[OpenWrt-Devel] [PATCH v2] ath79: add support for COMFAST CF-E130N v2
Adrian Schmutzler
mail at adrianschmutzler.de
Thu Nov 14 11:04:49 EST 2019
Hi,
> -----Original Message-----
> From: openwrt-devel [mailto:openwrt-devel-bounces at lists.openwrt.org] On
> Behalf Of admin at kryma.net
> Sent: Mittwoch, 13. November 2019 19:23
> To: openwrt-devel at lists.openwrt.org
> Cc: Pavel Balan <admin at kryma.net>
> Subject: [OpenWrt-Devel] [PATCH v2] ath79: add support for COMFAST CF-E130N
> v2
>
> From: Pavel Balan <admin at kryma.net>
>
> This patch adds support for the COMFAST CF-E130N v2, an outdoor wireless
> CPE with a single Ethernet port and a 802.11bgn radio.
>
> Specifications:
>
> - QCA9531 SoC
> - 1x 10/100 Mbps Ethernet, both with PoE-in support
> - 64 MB of RAM (DDR2)
> - 16 MB of FLASH
> - 5 dBi built-in antenna
> - POWER/LAN/WLAN green LEDs
> - 4x RSSI LEDs (2x red, 2x green)
> - UART (115200 8N1) and GPIO (J9) headers on PCB
>
> Flashing instructions:
>
> The original firmware is based on OpenWrt so a sysupgrade image can be
> installed via the stock web GUI.
>
> The U-boot bootloader also contains a backup TFTP client to upload the
> firmware from. Upon boot, it checks its ethernet network for the IP
> 192.168.1.10. Host a TFTP server and provide the image to be flashed as
> file firmware_auto.bin.
>
> Changes since v1:
>
> -Formatting fixes.
> -Looked into rssi_medium_high more - found the correct GPIO pin.
> -Removed the pin muxer.
> -Changed 802.11an to 802.11bgn in the patch description.
>
> Open questions:
>
> -LED menu in LUCI does not show the list of LEDs properly.
> A LUCI issue or a device config one?
Please put patch revision changes and questions after a line with "---" mark in your commit message. This automatically cuts off those when the patch is applied to a repository with git am.
>
>
> Signed-off-by: Pavel Balan <admin at kryma.net>
> ---
> .../ath79/dts/qca9531_comfast_cf-e130n-v2.dts | 139 ++++++++++++++++++
> .../generic/base-files/etc/board.d/01_leds | 8 +
> target/linux/ath79/image/generic.mk | 10 ++
> 3 files changed, 157 insertions(+)
> create mode 100644 target/linux/ath79/dts/qca9531_comfast_cf-e130n-v2.dts
>
> diff --git a/target/linux/ath79/dts/qca9531_comfast_cf-e130n-v2.dts
> b/target/linux/ath79/dts/qca9531_comfast_cf-e130n-v2.dts
> new file mode 100644
> index 0000000000..b5527c0a49
> --- /dev/null
> +++ b/target/linux/ath79/dts/qca9531_comfast_cf-e130n-v2.dts
> @@ -0,0 +1,139 @@
> +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
> +/dts-v1/;
> +
> +#include <dt-bindings/gpio/gpio.h>
> +#include <dt-bindings/input/input.h>
> +
> +#include "qca953x.dtsi"
> +
> +/ {
> + compatible = "comfast,cf-e130n-v2", "qca,qca9531";
> + model = "COMFAST CF-E130N v2";
> +
> + aliases {
> + serial0 = &uart;
> + led-boot = &led_rssihigh;
> + led-failsafe = &led_rssihigh;
> + led-upgrade = &led_rssihigh;
> + label-mac-device = ð0;
> + };
> +
> + leds {
> + compatible = "gpio-leds";
> +
> + pinctrl-names = "default";
> + pinctrl-0 = <&led_rssimediumhigh_pin>;
I do not see the node corresponding to this reference. So, you haven't even build-tested that one (it should produce an error during build...).
> +
> + led_wlan {
> + label = "cf-e130n-v2:green:wlan";
> + gpios = <&gpio 0 GPIO_ACTIVE_LOW>;
> + linux,default-trigger = "phy0tpt";
> + };
> +
> + led_lan {
> + label = "cf-e130n-v2:green:lan";
> + gpios = <&gpio 2 GPIO_ACTIVE_LOW>;
> + };
> +
> + led_unused {
> + label = "cf-e130n-v2:green:unused";
> + gpios = <&gpio 3 GPIO_ACTIVE_LOW>;
> + };
> +
> + led_rssilow {
> + label = "cf-e130n-v2:red:rssilow";
> + gpios = <&gpio 11 GPIO_ACTIVE_LOW>;
> + };
> +
> + led_rssimediumlow {
> + label = "cf-e130n-v2:red:rssimediumlow";
> + gpios = <&gpio 12 GPIO_ACTIVE_LOW>;
> + };
> +
> + led_rssimediumhigh {
> + label = "cf-e130n-v2:green:rssimediumhigh";
> + gpios = <&gpio 14 GPIO_ACTIVE_LOW>;
> + };
> +
> + led_rssihigh: led_rssihigh {
> + label = "cf-e130n-v2:green:rssihigh";
> + gpios = <&gpio 16 GPIO_ACTIVE_LOW>;
> + };
Sorry, maybe I wasn't precise enough here:
The _node label_ should be prefixed by "led_", but the _node name_ should not include it:
" led_rssihigh: rssihigh {"
" rssimediumhigh {"
etc.
> + };
> +
> + keys {
> + compatible = "gpio-keys";
> +
> + reset {
> + label = "reset";
> + linux,code = <KEY_RESTART>;
> + gpios = <&gpio 17 GPIO_ACTIVE_LOW>;
> + debounce-interval = <60>;
> + };
> + };
> +};
> +
> +&spi {
> + status = "okay";
> +
> + num-cs = <1>;
> +
> + flash at 0 {
> + compatible = "jedec,spi-nor";
> + reg = <0>;
> + spi-max-frequency = <25000000>;
> +
> + partitions {
> + compatible = "fixed-partitions";
> + #address-cells = <1>;
> + #size-cells = <1>;
> +
> + partition at 0 {
> + label = "u-boot";
> + reg = <0x000000 0x010000>;
> + read-only;
> + };
> +
> + art: partition at 10000 {
> + label = "art";
> + reg = <0x010000 0x010000>;
> + read-only;
> + };
> +
> + partition at 20000 {
> + compatible = "denx,uimage";
> + label = "firmware";
> + reg = <0x020000 0x7d0000>;
> + };
> +
> + partition at 7f0000 {
> + label = "nvram";
> + reg = <0x7f0000 0x010000>;
> + read-only;
> + };
> + };
> + };
> +};
> +
> +&uart {
> + status = "okay";
> +
> +};
Remove empty line.
> +
> +ð0 {
> + status = "okay";
> + phy-handle = <&swphy0>;
Add empty line after status.
> +
> + mtd-mac-address = <&art 0x0>;
> +
> + gmac-config {
> + device = <&gmac>;
> + switch-phy-swap = <1>;
> + };
> +};
> +
> +&wmac {
> + status = "okay";
Add empty line after status.
> + mtd-cal-data = <&art 0x1000>;
> +};
> +
Remove empty line at the end.
Best
Adrian
-------------- next part --------------
A non-text attachment was scrubbed...
Name: openpgp-digital-signature.asc
Type: application/pgp-signature
Size: 834 bytes
Desc: not available
URL: <http://lists.infradead.org/pipermail/openwrt-devel/attachments/20191114/57d3158e/attachment.sig>
-------------- next part --------------
_______________________________________________
openwrt-devel mailing list
openwrt-devel at lists.openwrt.org
https://lists.openwrt.org/mailman/listinfo/openwrt-devel
More information about the openwrt-devel
mailing list