[OpenWrt-Devel] [PATCH] ath79: add support for TP-Link Archer A7
Karl-Felix Glatzer
karl.glatzer at gmx.de
Sat Nov 10 12:06:08 EST 2018
This patch adds support for TP-Link Archer A7
Specification:
- SOC: QCA9563
- Flash: 16 MiB (SPI)
- RAM: 128 MiB (DDR2)
- Ethernet: 4x 1Gbps LAN + 1x 1Gbps WAN
- Wireless:
- 2.4GHz (bgn) SoC internal
- 5GHz (ac) QCA988x
- USB: 1x USB 2.0 port
- Button: 1x power, 1x reset, 1x wps
- LED: 10x LEDs
- UART: holes in PCB
- Vcc, GND, RX, TX from ethernet port side
- 115200n8
Flash instruction using factory image:
1. Connect the computer to one of the LAN ports of the Archer A7
2. Set the computer IP to 192.168.0.66
3. Start a tftp server with the OpenWrt factory image in the tftp
root directory renamed to ArcherC7v5_tp_recovery.bin
2. Connect power cable to Archer A7, press and hold the reset button
and turn the router on
3. Keep the reset button pressed for ~5 seconds
4. Wait ~150 seconds to complete flashing
Signed-off-by: Karl-Felix Glatzer <karl.glatzer at gmx.de>
---
.../ath79/base-files/etc/board.d/01_leds | 7 +
.../ath79/base-files/etc/board.d/02_network | 4 +
.../etc/hotplug.d/firmware/11-ath10k-caldata | 1 +
.../ath79/dts/qca9563_tplink_archer-a7-v5.dts | 255 ++++++++++++++++++
target/linux/ath79/image/common-tp-link.mk | 9 +
target/linux/ath79/image/generic-tp-link.mk | 16 ++
tools/firmware-utils/src/tplink-safeloader.c | 46 +++-
7 files changed, 337 insertions(+), 1 deletion(-)
create mode 100644 target/linux/ath79/dts/qca9563_tplink_archer-a7-v5.dts
diff --git a/target/linux/ath79/base-files/etc/board.d/01_leds b/target/linux/ath79/base-files/etc/board.d/01_leds
index f04eb7f5c6..4ddf04ef84 100755
--- a/target/linux/ath79/base-files/etc/board.d/01_leds
+++ b/target/linux/ath79/base-files/etc/board.d/01_leds
@@ -57,6 +57,13 @@ tplink,tl-mr3020-v1|\
tplink,tl-mr3040-v2)
ucidef_set_led_netdev "lan" "LAN" "tp-link:green:lan" "eth0"
;;
+tplink,archer-a7-v5)
+ ucidef_set_led_switch "wan" "WAN" "tp-link:green:wan" "switch0" "0x02"
+ ucidef_set_led_switch "lan1" "LAN1" "tp-link:green:lan1" "switch0" "0x04"
+ ucidef_set_led_switch "lan2" "LAN2" "tp-link:green:lan2" "switch0" "0x08"
+ ucidef_set_led_switch "lan3" "LAN3" "tp-link:green:lan3" "switch0" "0x10"
+ ucidef_set_led_switch "lan4" "LAN4" "tp-link:green:lan4" "switch0" "0x20"
+ ;;
tplink,tl-wr1043nd-v4)
ucidef_set_led_switch "wan" "WAN" "tp-link:green:wan" "switch0" "0x20"
ucidef_set_led_switch "lan1" "LAN1" "tp-link:green:lan1" "switch0" "0x10"
diff --git a/target/linux/ath79/base-files/etc/board.d/02_network b/target/linux/ath79/base-files/etc/board.d/02_network
index 5f02c5769a..7c7c9e14e1 100755
--- a/target/linux/ath79/base-files/etc/board.d/02_network
+++ b/target/linux/ath79/base-files/etc/board.d/02_network
@@ -107,6 +107,10 @@ ath79_setup_interfaces()
ucidef_add_switch "switch0" \
"0 at eth0" "3:lan:1" "5:lan:2" "4:wan"
;;
+ tplink,archer-a7-v5)
+ ucidef_add_switch "switch0" \
+ "0 at eth0" "2:lan:1" "3:lan:2" "4:lan:3" "5:lan:4" "1:wan"
+ ;;
tplink,archer-c7-v1|\
tplink,archer-c7-v2|\
tplink,tl-wdr4900-v2)
diff --git a/target/linux/ath79/base-files/etc/hotplug.d/firmware/11-ath10k-caldata b/target/linux/ath79/base-files/etc/hotplug.d/firmware/11-ath10k-caldata
index dfe2d3ef31..6001df07bb 100644
--- a/target/linux/ath79/base-files/etc/hotplug.d/firmware/11-ath10k-caldata
+++ b/target/linux/ath79/base-files/etc/hotplug.d/firmware/11-ath10k-caldata
@@ -100,6 +100,7 @@ case "$FIRMWARE" in
ath10kcal_extract "ART" 20480 2116
ath10kcal_patch_mac $(macaddr_add $(cat /sys/class/net/eth0/address) +16)
;;
+ tplink,archer-a7-v5|\
tplink,archer-c7-v2)
ath10kcal_extract "art" 20480 2116
ath10kcal_patch_mac $(macaddr_add $(cat /sys/class/net/eth1/address) -1)
diff --git a/target/linux/ath79/dts/qca9563_tplink_archer-a7-v5.dts b/target/linux/ath79/dts/qca9563_tplink_archer-a7-v5.dts
new file mode 100644
index 0000000000..c62cb63b0d
--- /dev/null
+++ b/target/linux/ath79/dts/qca9563_tplink_archer-a7-v5.dts
@@ -0,0 +1,255 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/dts-v1/;
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+
+#include "qca956x.dtsi"
+
+/ {
+ compatible = "tplink,archer-a7-v5", "qca,qca9563";
+ model = "TP-Link Archer A7 Version 5";
+
+ chosen {
+ bootargs = "console=ttyS0,115200n8";
+ };
+
+ aliases {
+ led-status = &system;
+ };
+
+ gpio_leds: leds {
+ compatible = "gpio-leds";
+
+ system: system {
+ label = "tp-link:green:system";
+ gpios = <&gpio 6 GPIO_ACTIVE_LOW>;
+ default-state = "on";
+ };
+
+ led_wlan2g: wlan2g {
+ label = "tp-link:green:wlan2g";
+ gpios = <&gpio 14 GPIO_ACTIVE_LOW>;
+ default-state = "off";
+ linux,default-trigger = "phy1tpt";
+ };
+
+ usb {
+ label = "tp-link:green:usb";
+ gpios = <&gpio 7 GPIO_ACTIVE_LOW>;
+ default-state = "off";
+ trigger-sources = <&hub_port0>;
+ linux,default-trigger = "usbport";
+ };
+ };
+
+ gpio_keys: keys {
+ compatible = "gpio-keys";
+
+ reset {
+ label = "Reset button";
+ linux,code = <KEY_RESTART>;
+ gpios = <&gpio 11 GPIO_ACTIVE_LOW>;
+ debounce-interval = <60>;
+ };
+
+ wps {
+ label = "WPS button";
+ linux,code = <KEY_WPS_BUTTON>;
+ gpios = <&gpio 2 GPIO_ACTIVE_LOW>;
+ debounce-interval = <60>;
+ };
+ };
+
+ gpio-export {
+ compatible = "gpio-export";
+
+ gpio_usb_power {
+ gpio-export,name = "tp-link:power:usb";
+ gpio-export,output = <1>;
+ gpios = <&gpio 19 GPIO_ACTIVE_HIGH>;
+ };
+ };
+};
+
+&pcie {
+ status = "okay";
+};
+
+&uart {
+ status = "okay";
+};
+
+&gpio {
+ status = "okay";
+};
+
+&usb_phy0 {
+ status = "okay";
+};
+
+&usb0 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "okay";
+
+ hub_port0: port at 1 {
+ reg = <1>;
+ #trigger-source-cells = <0>;
+ };
+};
+
+&gpio_leds {
+ wlan5g {
+ label = "tp-link:green:wlan5g";
+ gpios = <&gpio 9 GPIO_ACTIVE_LOW>;
+ default-state = "off";
+ linux,default-trigger = "phy0tpt";
+ };
+
+ wan {
+ label = "tp-link:green:wan";
+ gpios = <&gpio 21 GPIO_ACTIVE_LOW>;
+ default-state = "off";
+ };
+
+ wan_fail {
+ label = "tp-link:orange:wan";
+ gpios = <&gpio 20 GPIO_ACTIVE_LOW>;
+ default-state = "off";
+ };
+
+ lan1 {
+ label = "tp-link:green:lan1";
+ gpios = <&gpio 8 GPIO_ACTIVE_LOW>;
+ default-state = "off";
+ };
+
+ lan2 {
+ label = "tp-link:green:lan2";
+ gpios = <&gpio 17 GPIO_ACTIVE_LOW>;
+ default-state = "off";
+ };
+
+ lan3 {
+ label = "tp-link:green:lan3";
+ gpios = <&gpio 16 GPIO_ACTIVE_LOW>;
+ default-state = "off";
+ };
+
+ lan4 {
+ label = "tp-link:green:lan4";
+ gpios = <&gpio 15 GPIO_ACTIVE_LOW>;
+ default-state = "off";
+ };
+
+ wps {
+ label = "tp-link:green:wps";
+ gpios = <&gpio 1 GPIO_ACTIVE_LOW>;
+ default-state = "off";
+ };
+};
+
+&spi {
+ status = "okay";
+ num-cs = <1>;
+
+ flash at 0 {
+ compatible = "jedec,spi-nor";
+ reg = <0>;
+ spi-max-frequency = <25000000>;
+
+ mtdparts: partitions {
+ compatible = "fixed-partitions";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ };
+ };
+};
+
+&mdio0 {
+ status = "okay";
+
+ phy-mask = <0>;
+
+ phy0: ethernet-phy at 0 {
+ reg = <0>;
+ phy-mode = "sgmii";
+
+ qca,ar8327-initvals = <
+ 0x04 0x00080080 /* PORT0 PAD MODE CTRL */
+ 0x10 0x81000080 /* POWER_ON_STRIP */
+ 0x50 0xcc35cc35 /* LED_CTRL0 */
+ 0x54 0xcb37cb37 /* LED_CTRL1 */
+ 0x58 0x00000000 /* LED_CTRL2 */
+ 0x5c 0x00f3cf00 /* LED_CTRL3 */
+ 0x7c 0x0000007e /* PORT0_STATUS */
+ >;
+ };
+};
+
+ð0 {
+ status = "okay";
+
+ pll-data = <0x03000101 0x00000101 0x00001919>;
+
+ phy-mode = "sgmii";
+ mtd-mac-address = <&info 0x8>;
+ phy-handle = <&phy0>;
+};
+
+&wmac {
+ status = "okay";
+ mtd-cal-data = <&art 0x1000>;
+ mtd-mac-address = <&info 0x8>;
+};
+
+&mtdparts {
+ factory-uboot at 0 {
+ label = "factory-uboot";
+ reg = <0x000000 0x020000>;
+ read-only;
+ };
+
+ uboot: u-boot at 0 {
+ label = "u-boot";
+ reg = <0x020000 0x020000>;
+ read-only;
+ };
+
+ kernel: kernel at 0 {
+ label = "kernel";
+ reg = <0x040000 0x190000>;
+ };
+
+ rootfs: rootfs at 0 {
+ label = "rootfs";
+ reg = <0x1d0000 0xd30000>;
+ };
+
+ info: info at f40000 {
+ label = "info";
+ reg = <0xf40000 0x020000>;
+ };
+
+ config: config at f60000 {
+ label = "config";
+ reg = <0xf60000 0x050000>;
+ };
+
+ partition at fc0000 {
+ label = "partition-table";
+ reg = <0xfc0000 0x010000>;
+ };
+
+ firmware at 40000 {
+ label = "firmware";
+ reg = <0x040000 0xec0000>;
+ };
+
+ art: art at ff0000 {
+ label = "art";
+ reg = <0xff0000 0x010000>;
+ read-only;
+ };
+};
diff --git a/target/linux/ath79/image/common-tp-link.mk b/target/linux/ath79/image/common-tp-link.mk
index 7490aeb1f3..4a29459196 100644
--- a/target/linux/ath79/image/common-tp-link.mk
+++ b/target/linux/ath79/image/common-tp-link.mk
@@ -39,6 +39,15 @@ define Build/mktplinkfw-combined
@mv $@.new $@
endef
+define Build/uImageArcher
+ ${STAGING_DIR_HOST}/bin/mkimage \
+ -A $(LINUX_KARCH) \
+ -O linux -T kernel \
+ -C $(1) -a $(KERNEL_LOADADDR) -e $(if $(KERNEL_ENTRY),$(KERNEL_ENTRY),$(KERNEL_LOADADDR)) \
+ -n '$(call toupper,$(LINUX_KARCH)) OpenWrt Linux-$(LINUX_VERSION)' -d $@ $@.new
+ @mv $@.new $@
+endef
+
define Device/tplink
TPLINK_HWREV := 0x1
TPLINK_HEADER_VERSION := 1
diff --git a/target/linux/ath79/image/generic-tp-link.mk b/target/linux/ath79/image/generic-tp-link.mk
index d65e29e72a..d24222e9e3 100644
--- a/target/linux/ath79/image/generic-tp-link.mk
+++ b/target/linux/ath79/image/generic-tp-link.mk
@@ -1,5 +1,21 @@
include ./common-tp-link.mk
+define Device/tplink_archer-a7-v5
+ $(Device/tplink)
+ ATH_SOC := qca9563
+ DEVICE_TITLE := TP-LINK Archer A7 v5
+ DEVICE_PACKAGES := kmod-usb-core kmod-usb2 kmod-usb-ledtrig-usbport kmod-ath10k ath10k-firmware-qca988x
+ SUPPORTED_DEVICES := tplink,archer-a7-v5
+ BOARDNAME := ARCHER-A7-V5
+ TPLINK_BOARD_ID := ARCHER-A7-V5
+ IMAGE_SIZE := 15104k
+ KERNEL := kernel-bin | append-dtb | lzma | uImageArcher lzma
+ IMAGE/sysupgrade.bin := append-rootfs | tplink-safeloader sysupgrade | \
+ append-metadata | check-size $$$$(IMAGE_SIZE)
+ IMAGE/factory.bin := append-rootfs | tplink-safeloader factory
+endef
+TARGET_DEVICES += tplink_archer-a7-v5
+
define Device/tplink_archer-c7-v1
$(Device/tplink-8mlzma)
ATH_SOC := qca9558
diff --git a/tools/firmware-utils/src/tplink-safeloader.c b/tools/firmware-utils/src/tplink-safeloader.c
index a51cca476e..7fa0a313d4 100644
--- a/tools/firmware-utils/src/tplink-safeloader.c
+++ b/tools/firmware-utils/src/tplink-safeloader.c
@@ -357,6 +357,50 @@ static struct device_info boards[] = {
.last_sysupgrade_partition = "file-system"
},
+ /** Firmware layout for the A7-V5 */
+ {
+ .id = "ARCHER-A7-V5",
+ .support_list =
+ "SupportList:\n"
+ "{product_name:Archer A7,product_ver:5.0.0,special_id:45550000}\n"
+ "{product_name:Archer A7,product_ver:5.0.0,special_id:55530000}\n"
+ "{product_name:Archer A7,product_ver:5.0.0,special_id:43410000}\n"
+ "{product_name:Archer A7,product_ver:5.0.0,special_id:4A500000}\n"
+ "{product_name:Archer A7,product_ver:5.0.0,special_id:54570000}\n",
+ .support_trail = '\x00',
+ .soft_ver = "soft_ver:1.0.0\n",
+
+ /**
+ We use a bigger os-image partition than the stock images (and thus
+ smaller file-system), as our kernel doesn't fit in the stock firmware's
+ 1MB os-image.
+ */
+ .partitions = {
+ {"factory-boot", 0x00000, 0x20000},
+ {"fs-uboot", 0x20000, 0x20000},
+ {"os-image", 0x40000, 0x190000}, /* Stock: base 0x40000 size 0x120000 */
+ {"file-system", 0x1d0000, 0xd30000}, /* Stock: base 0x160000 size 0xda0000 */
+ {"default-mac", 0xf40000, 0x00200},
+ {"pin", 0xf40200, 0x00200},
+ {"device-id", 0xf40400, 0x00100},
+ {"product-info", 0xf40500, 0x0fb00},
+ {"soft-version", 0xf50000, 0x00100},
+ {"extra-para", 0xf51000, 0x01000},
+ {"support-list", 0xf52000, 0x0a000},
+ {"profile", 0xf5c000, 0x04000},
+ {"default-config", 0xf60000, 0x10000},
+ {"user-config", 0xf70000, 0x40000},
+ {"certificate", 0xfb0000, 0x10000},
+ {"partition-table", 0xfc0000, 0x10000},
+ {"log", 0xfd0000, 0x20000},
+ {"radio", 0xff0000, 0x10000},
+ {NULL, 0, 0}
+ },
+
+ .first_sysupgrade_partition = "os-image",
+ .last_sysupgrade_partition = "file-system",
+ },
+
/** Firmware layout for the C25v1 */
{
.id = "ARCHER-C25-V1",
@@ -1577,7 +1621,7 @@ static void build_image(const char *output,
strcasecmp(info->id, "TLWR1043NV5") == 0) {
const char mdat[11] = {0x00, 0x00, 0x00, 0x02, 0x00, 0x00, 0x00, 0x00, 0x01, 0x00, 0x00};
parts[5] = put_data("extra-para", mdat, 11);
- } else if (strcasecmp(info->id, "ARCHER-C7-V4") == 0 || strcasecmp(info->id, "ARCHER-C7-V5") == 0) {
+ } else if (strcasecmp(info->id, "ARCHER-A7-V5") == 0 || strcasecmp(info->id, "ARCHER-C7-V4") == 0 || strcasecmp(info->id, "ARCHER-C7-V5") == 0) {
const char mdat[11] = {0x01, 0x00, 0x00, 0x02, 0x00, 0x00, 0xca, 0x00, 0x01, 0x00, 0x00};
parts[5] = put_data("extra-para", mdat, 11);
}
--
2.19.1
_______________________________________________
openwrt-devel mailing list
openwrt-devel at lists.openwrt.org
https://lists.openwrt.org/mailman/listinfo/openwrt-devel
More information about the openwrt-devel
mailing list