[OpenWrt-Devel] [PATCH 4/6] [CC] [backport] ramips: Add GL-MT300A support
alzhao
alzhao at gmail.com
Wed May 4 23:02:08 EDT 2016
Backport of changeset 48992
Add GL-MT300A support
Signed-off-by: alzhao <alzhao at gmail.com>
---
target/linux/ramips/base-files/etc/board.d/01_leds | 3 +
.../linux/ramips/base-files/etc/board.d/02_network | 7 +
target/linux/ramips/base-files/lib/ramips.sh | 3 +
.../ramips/base-files/lib/upgrade/platform.sh | 1 +
target/linux/ramips/dts/GL-MT300A.dts | 164 +++++++++++++++++++++
target/linux/ramips/image/Makefile | 2 +
target/linux/ramips/mt7620/profiles/gli.mk | 16 ++
7 files changed, 196 insertions(+)
create mode 100644 target/linux/ramips/dts/GL-MT300A.dts
create mode 100644 target/linux/ramips/mt7620/profiles/gli.mk
diff --git a/target/linux/ramips/base-files/etc/board.d/01_leds b/target/linux/ramips/base-files/etc/board.d/01_leds
index 5327d00..a3661e8 100755
--- a/target/linux/ramips/base-files/etc/board.d/01_leds
+++ b/target/linux/ramips/base-files/etc/board.d/01_leds
@@ -147,6 +147,9 @@ case $board in
mofi3500-3gn)
set_usb_led "mofi3500-3gn:green:usb"
;;
+ gl-mt300a)
+ set_wifi_led "gl-mt300a:wlan"
+ ;;
mpr-a1)
set_wifi_led "hame:blue:system"
;;
diff --git a/target/linux/ramips/base-files/etc/board.d/02_network b/target/linux/ramips/base-files/etc/board.d/02_network
index a78912d..b5c2b81 100755
--- a/target/linux/ramips/base-files/etc/board.d/02_network
+++ b/target/linux/ramips/base-files/etc/board.d/02_network
@@ -153,6 +153,13 @@ ramips_setup_interfaces()
ucidef_add_switch_vlan "switch0" "1" "0 1 2 3 6t"
ucidef_add_switch_vlan "switch0" "2" "4 6t"
;;
+
+ gl-mt300a)
+ ucidef_set_interfaces_lan_wan "eth0.1" "eth0.2"
+ ucidef_add_switch "switch0" "1" "1"
+ ucidef_add_switch_vlan "switch0" "2" "0 6t"
+ ucidef_add_switch_vlan "switch0" "1" "1 2 3 4 6t"
+ ;;
whr-1166d)
ucidef_set_interfaces_lan_wan "eth0.1" "eth0.2"
diff --git a/target/linux/ramips/base-files/lib/ramips.sh b/target/linux/ramips/base-files/lib/ramips.sh
index 8dc05b0..40c26e6 100755
--- a/target/linux/ramips/base-files/lib/ramips.sh
+++ b/target/linux/ramips/base-files/lib/ramips.sh
@@ -169,6 +169,9 @@ ramips_board_detect() {
*"F5D8235 v2")
name="f5d8235-v2"
;;
+ *"GL-MT300A")
+ name="gl-mt300a"
+ ;;
*"Hauppauge Broadway")
name="broadway"
;;
diff --git a/target/linux/ramips/base-files/lib/upgrade/platform.sh b/target/linux/ramips/base-files/lib/upgrade/platform.sh
index a3d0175..cfd44d7 100755
--- a/target/linux/ramips/base-files/lib/upgrade/platform.sh
+++ b/target/linux/ramips/base-files/lib/upgrade/platform.sh
@@ -55,6 +55,7 @@ platform_check_image() {
fonera20n | \
freestation5 | \
firewrt |\
+ gl-mt300a |\
pbr-m1 |\
hg255d | \
hlk-rm04 | \
diff --git a/target/linux/ramips/dts/GL-MT300A.dts b/target/linux/ramips/dts/GL-MT300A.dts
new file mode 100644
index 0000000..c1eb0a9
--- /dev/null
+++ b/target/linux/ramips/dts/GL-MT300A.dts
@@ -0,0 +1,164 @@
+/dts-v1/;
+
+/include/ "mt7620a.dtsi"
+
+/ {
+ compatible = "GL-MT300A", "ralink,mt7620a-soc";
+ model = "GL-MT300A";
+
+ chosen {
+ bootargs = "console=ttyS0,115200";
+ };
+
+ palmbus at 10000000 {
+ gpio0: gpio at 600 {
+ status = "okay";
+ };
+
+ gpio1: gpio at 638 {
+ status = "okay";
+ };
+
+ gpio2: gpio at 660 {
+ status = "okay";
+ };
+
+ gpio3: gpio at 688 {
+ status = "okay";
+ };
+
+ spi at b00 {
+ status = "okay";
+
+ m25p80 at 0 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "w25q128";
+ reg = <0 0>;
+ linux,modalias = "m25p80", "w25q128";
+ spi-max-frequency = <10000000>;
+
+ partition at 0 {
+ label = "u-boot";
+ reg = <0x0 0x30000>;
+ };
+
+ partition at 30000 {
+ label = "u-boot-env";
+ reg = <0x30000 0x10000>;
+ read-only;
+ };
+
+ factory: partition at 40000 {
+ label = "factory";
+ reg = <0x40000 0x10000>;
+ read-only;
+ };
+
+ partition at 50000 {
+ label = "firmware";
+ reg = <0x50000 0xf80000>;
+ };
+
+ partition at ff0000 {
+ label = "art";
+ reg = <0xff0000 0x10000>;
+ };
+ };
+ };
+ };
+
+ sdhci at 10130000 {
+ status = "okay";
+ };
+
+ ehci at 101c0000 {
+ status = "okay";
+ };
+
+ ohci at 101c1000 {
+ status = "okay";
+ };
+
+ ethernet at 10100000 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&ephy_pins>;
+ mtd-mac-address = <&factory 0x4000>;
+ ralink,port-map = "wllll";
+ };
+
+ wmac at 10180000 {
+ ralink,mtd-eeprom = <&factory 0>;
+ };
+
+ pcie at 10140000 {
+ status = "okay";
+
+ pcie-bridge {
+ mt76 at 0,0 {
+ reg = <0x0000 0 0 0 0>;
+ device_type = "pci";
+ mediatek,mtd-eeprom = <&factory 0x8000>;
+ mediatek,2ghz = <0>;
+ };
+ };
+ };
+
+ pinctrl {
+ state_default: pinctrl0 {
+ gpio {
+ ralink,group = "wled","ephy","uartf","i2c";
+ ralink,function = "gpio";
+ };
+ };
+ };
+
+ gpio-leds {
+ compatible = "gpio-leds";
+
+ wan {
+ label = "gl-mt300a:wan";
+ gpios = <&gpio2 0 1>;
+ };
+
+ lan {
+ label = "gl-mt300a:lan";
+ gpios = <&gpio2 1 1>;
+ };
+
+ wlan {
+ label = "gl-mt300a:wlan";
+ gpios = <&gpio3 0 1>;
+ };
+
+ usb {
+ label = "gl-mt300a:usb";
+ gpios = <&gpio0 7 1>;
+ };
+
+ };
+
+ gpio-keys-polled {
+ compatible = "gpio-keys-polled";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ poll-interval = <20>;
+ reset {
+ label = "reset";
+ gpios = <&gpio0 13 1>;
+ linux,code = <0x198>;
+ };
+
+ BTN_0 {
+ label = "BTN_0";
+ gpios = <&gpio0 1 1>;
+ linux,code = <0x100>;
+ };
+
+ BTN_1 {
+ label = "BTN_1";
+ gpios = <&gpio0 2 1>;
+ linux,code = <0x101>;
+ };
+ };
+};
diff --git a/target/linux/ramips/image/Makefile b/target/linux/ramips/image/Makefile
index c4f4028..d4991ad 100644
--- a/target/linux/ramips/image/Makefile
+++ b/target/linux/ramips/image/Makefile
@@ -910,6 +910,7 @@ Image/Build/Profile/WR8305RT=$(call BuildFirmware/Default8M/$(1),$(1),wr8305rt,W
Image/Build/Profile/WRTNODE=$(call BuildFirmware/Default16M/$(1),$(1),wrtnode,WRTNODE)
Image/Build/Profile/WT3020=$(call BuildFirmware/PorayDualSize/$(1),$(1),wt3020,WT3020)
Image/Build/Profile/XIAOMI-MIWIFI-MINI=$(call BuildFirmware/Default16M/$(1),$(1),xiaomi-miwifi-mini,XIAOMI-MIWIFI-MINI)
+Image/Build/Profile/GL-MT300A=$(call BuildFirmware/Default16M/$(1),$(1),gl-mt300a,GL-MT300A)
Image/Build/Profile/ZTE-Q7=$(call BuildFirmware/Default8M/$(1),$(1),zte-q7,ZTE-Q7)
Image/Build/Profile/ZBT-WA05=$(call BuildFirmware/Default8M/$(1),$(1),zbt-wa05,ZBT-WA05)
Image/Build/Profile/ArcherC20i=$(call BuildFirmware/Tplink/$(1),$(1),ArcherC20i,ArcherC20i)
@@ -944,6 +945,7 @@ define Image/Build/Profile/Default
$(call Image/Build/Profile/WRTNODE,$(1))
$(call Image/Build/Profile/WT3020,$(1))
$(call Image/Build/Profile/XIAOMI-MIWIFI-MINI,$(1))
+ $(call Image/Build/Profile/GL-MT300A,$(1))
$(call Image/Build/Profile/ZTE-Q7,$(1))
$(call Image/Build/Profile/ZBT-WA05,$(1))
$(call Image/Build/Profile/ArcherC20i,$(1))
diff --git a/target/linux/ramips/mt7620/profiles/gli.mk b/target/linux/ramips/mt7620/profiles/gli.mk
new file mode 100644
index 0000000..53e2e9d
--- /dev/null
+++ b/target/linux/ramips/mt7620/profiles/gli.mk
@@ -0,0 +1,16 @@
+#
+# Copyright (C) 2015 OpenWrt.org
+#
+# This is free software, licensed under the GNU General Public License v2.
+# See /LICENSE for more information.
+#
+
+define Profile/GL-MT300A
+ NAME:=GL-MT300A
+ PACKAGES:=kmod-usb-core kmod-usb-dwc2 kmod-usb2 kmod-usb-ohci kmod-mt76
+endef
+
+define Profile/GL-MT300A/Description
+ Support for gl-mt300a Router
+endef
+$(eval $(call Profile,GL-MT300A))
--
1.9.1
_______________________________________________
openwrt-devel mailing list
openwrt-devel at lists.openwrt.org
https://lists.openwrt.org/cgi-bin/mailman/listinfo/openwrt-devel
More information about the openwrt-devel
mailing list