[OpenWrt-Devel] [PATCH 2/6] [CC] [backport] ar71xx: add GL-AR300 support
alzhao
alzhao at gmail.com
Wed May 4 23:02:06 EDT 2016
Backport of changeset 47621
Add support for GL-AR300
Signed-off-by: alzhao <alzhao at gmail.com>
---
.../ar71xx/base-files/etc/uci-defaults/01_leds | 4 +
.../ar71xx/base-files/etc/uci-defaults/02_network | 6 ++
target/linux/ar71xx/base-files/lib/ar71xx.sh | 3 +
.../ar71xx/base-files/lib/upgrade/platform.sh | 1 +
target/linux/ar71xx/config-3.18 | 1 +
.../ar71xx/files/arch/mips/ath79/mach-gl-ar300.c | 106 +++++++++++++++++++++
target/linux/ar71xx/generic/profiles/gli.mk | 11 +++
target/linux/ar71xx/image/Makefile | 8 ++
.../patches-3.18/912-MIPS-ath79-add-gl_ar300.patch | 39 ++++++++
9 files changed, 179 insertions(+)
create mode 100644 target/linux/ar71xx/files/arch/mips/ath79/mach-gl-ar300.c
create mode 100644 target/linux/ar71xx/patches-3.18/912-MIPS-ath79-add-gl_ar300.patch
diff --git a/target/linux/ar71xx/base-files/etc/uci-defaults/01_leds b/target/linux/ar71xx/base-files/etc/uci-defaults/01_leds
index 0bd0b35..7c00947 100644
--- a/target/linux/ar71xx/base-files/etc/uci-defaults/01_leds
+++ b/target/linux/ar71xx/base-files/etc/uci-defaults/01_leds
@@ -185,6 +185,10 @@ gl-ar150)
ucidef_set_led_wlan "wlan" "WLAN" "gl_ar150:wlan" "phy0tpt"
;;
+gl-ar300)
+ ucidef_set_led_wlan "wlan" "WLAN" "gl_ar300:wlan" "phy0tpt"
+ ;;
+
gl-inet)
ucidef_set_led_netdev "lan" "LAN" "gl-connect:green:lan" "eth1"
ucidef_set_led_wlan "wlan" "WLAN" "gl-connect:red:wlan" "phy0tpt"
diff --git a/target/linux/ar71xx/base-files/etc/uci-defaults/02_network b/target/linux/ar71xx/base-files/etc/uci-defaults/02_network
index c7ba875..3cd97ec 100755
--- a/target/linux/ar71xx/base-files/etc/uci-defaults/02_network
+++ b/target/linux/ar71xx/base-files/etc/uci-defaults/02_network
@@ -391,6 +391,12 @@ wpe72)
ucidef_set_interfaces_lan_wan "eth1" "eth0"
;;
+gl-ar300)
+ ucidef_set_interfaces_lan_wan "eth1" "eth0"
+ ucidef_add_switch "switch0" "1" "1"
+ ucidef_add_switch_vlan "switch0" "1" "0 1 2 3 4"
+ ;;
+
wpj344)
ucidef_set_interfaces_lan_wan "eth0.1" "eth0.2"
ucidef_add_switch "switch0" "1" "1"
diff --git a/target/linux/ar71xx/base-files/lib/ar71xx.sh b/target/linux/ar71xx/base-files/lib/ar71xx.sh
index 813ff91..bc5dc17 100755
--- a/target/linux/ar71xx/base-files/lib/ar71xx.sh
+++ b/target/linux/ar71xx/base-files/lib/ar71xx.sh
@@ -442,6 +442,9 @@ ar71xx_board_detect() {
*"Dragino v2")
name="dragino2"
;;
+ *"GL-AR300")
+ name="gl-ar300"
+ ;;
*"EAP300 v2")
name="eap300v2"
;;
diff --git a/target/linux/ar71xx/base-files/lib/upgrade/platform.sh b/target/linux/ar71xx/base-files/lib/upgrade/platform.sh
index 59ee053..0800642 100755
--- a/target/linux/ar71xx/base-files/lib/upgrade/platform.sh
+++ b/target/linux/ar71xx/base-files/lib/upgrade/platform.sh
@@ -212,6 +212,7 @@ platform_check_image() {
dlan-pro-1200-ac | \
dragino2 | \
gl-ar150 | \
+ gl-ar300 | \
epg5000 | \
esr1750 | \
esr900 | \
diff --git a/target/linux/ar71xx/config-3.18 b/target/linux/ar71xx/config-3.18
index 3598a55..4365232 100644
--- a/target/linux/ar71xx/config-3.18
+++ b/target/linux/ar71xx/config-3.18
@@ -70,6 +70,7 @@ CONFIG_ATH79_MACH_ESR900=y
CONFIG_ATH79_MACH_EW_DORIN=y
CONFIG_ATH79_MACH_F9K1115V2=y
CONFIG_ATH79_MACH_GL_AR150=y
+CONFIG_ATH79_MACH_GL_AR300=y
CONFIG_ATH79_MACH_GL_INET=y
CONFIG_ATH79_MACH_GS_MINIBOX_V1=y
CONFIG_ATH79_MACH_GS_OOLITE=y
diff --git a/target/linux/ar71xx/files/arch/mips/ath79/mach-gl-ar300.c b/target/linux/ar71xx/files/arch/mips/ath79/mach-gl-ar300.c
new file mode 100644
index 0000000..62fafad
--- /dev/null
+++ b/target/linux/ar71xx/files/arch/mips/ath79/mach-gl-ar300.c
@@ -0,0 +1,106 @@
+/*
+ * Domino board support
+ *
+ * Copyright (C) 2011 dongyuqi <729650915 at qq.com>
+ * Copyright (C) 2011-2012 Gabor Juhos <juhosg at openwrt.org>
+ * Copyright (C) 2013 alzhao <alzhao at gmail.com>
+ * Copyright (C) 2014 Michel Stempin <michel.stempin at wanadoo.fr>
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License version 2 as published
+ * by the Free Software Foundation.
+*/
+
+#include <linux/gpio.h>
+#include <linux/platform_device.h>
+#include <linux/ath9k_platform.h>
+#include <asm/mach-ath79/ar71xx_regs.h>
+#include <asm/mach-ath79/ath79.h>
+
+#include "common.h"
+#include "dev-eth.h"
+#include "dev-gpio-buttons.h"
+#include "dev-leds-gpio.h"
+#include "dev-m25p80.h"
+#include "dev-usb.h"
+#include "dev-wmac.h"
+#include "machtypes.h"
+
+#define GL_AR300_GPIO_LED_WLAN 13
+#define GL_AR300_GPIO_LED_WAN 14
+#define GL_AR300_GPIO_BTN_RESET 16
+
+
+#define GL_AR300_KEYS_POLL_INTERVAL 20 /* msecs */
+#define GL_AR300_KEYS_DEBOUNCE_INTERVAL (3 * GL_AR300_KEYS_POLL_INTERVAL)
+
+#define GL_AR300_MAC0_OFFSET 0x0000
+#define GL_AR300_MAC1_OFFSET 0x0000
+#define GL_AR300_CALDATA_OFFSET 0x1000
+#define GL_AR300_WMAC_MAC_OFFSET 0x0000
+
+static struct gpio_led gl_ar300_leds_gpio[] __initdata = {
+ {
+ .name = "gl_ar300:wlan",
+ .gpio = GL_AR300_GPIO_LED_WLAN,
+ .active_low = 1,
+ },
+ {
+ .name = "gl_ar300:wan",
+ .gpio = GL_AR300_GPIO_LED_WAN,
+ .active_low = 1,
+ },
+};
+
+static struct gpio_keys_button gl_ar300_gpio_keys[] __initdata = {
+ {
+ .desc = "reset",
+ .type = EV_KEY,
+ .code = KEY_RESTART,
+ .debounce_interval = GL_AR300_KEYS_DEBOUNCE_INTERVAL,
+ .gpio = GL_AR300_GPIO_BTN_RESET,
+ .active_low = 1,
+ },
+};
+
+static void __init gl_ar300_setup(void)
+{
+
+ /* ART base address */
+ u8 *art = (u8 *) KSEG1ADDR(0x1fff0000);
+
+ /* disable PHY_SWAP and PHY_ADDR_SWAP bits */
+ //ath79_setup_ar933x_phy4_switch(false, false);
+
+ /* register flash. */
+ ath79_register_m25p80(NULL);
+
+ /* register gpio LEDs and keys */
+ ath79_register_leds_gpio(-1, ARRAY_SIZE(gl_ar300_leds_gpio),
+ gl_ar300_leds_gpio);
+ ath79_register_gpio_keys_polled(-1, GL_AR300_KEYS_POLL_INTERVAL,
+ ARRAY_SIZE(gl_ar300_gpio_keys),
+ gl_ar300_gpio_keys);
+
+ /* enable usb */
+ ath79_register_usb();
+ ath79_register_mdio(1, 0x0);
+
+ /* register eth0 as WAN, eth1 as LAN */
+ ath79_init_mac(ath79_eth0_data.mac_addr, art+GL_AR300_MAC0_OFFSET, 0);
+ ath79_switch_data.phy4_mii_en = 1;
+ ath79_switch_data.phy_poll_mask = BIT(4);
+ ath79_eth0_data.phy_if_mode = PHY_INTERFACE_MODE_MII;
+ ath79_eth0_data.phy_mask = BIT(4);
+ ath79_eth0_data.mii_bus_dev = &ath79_mdio1_device.dev;
+ ath79_register_eth(0);
+
+ ath79_init_mac(ath79_eth1_data.mac_addr, art+GL_AR300_MAC1_OFFSET, 0);
+ ath79_eth1_data.phy_if_mode = PHY_INTERFACE_MODE_GMII;
+ ath79_register_eth(1);
+
+ /* register wireless mac with cal data */
+ ath79_register_wmac(art + GL_AR300_CALDATA_OFFSET, art + GL_AR300_WMAC_MAC_OFFSET);
+}
+
+MIPS_MACHINE(ATH79_MACH_GL_AR300, "GL-AR300", "GL-AR300",gl_ar300_setup);
diff --git a/target/linux/ar71xx/generic/profiles/gli.mk b/target/linux/ar71xx/generic/profiles/gli.mk
index 89b2ead..e399739 100644
--- a/target/linux/ar71xx/generic/profiles/gli.mk
+++ b/target/linux/ar71xx/generic/profiles/gli.mk
@@ -25,3 +25,14 @@ define Profile/GL-AR150/Description
endef
$(eval $(call Profile,GL-AR150))
+
+define Profile/GL-AR300
+ NAME:=GL-AR300
+ PACKAGES:=kmod-usb-core kmod-usb2
+endef
+
+define Profile/GL-AR300/Description
+ Configuration of GL-AR300.
+endef
+
+$(eval $(call Profile,GL-AR300))
diff --git a/target/linux/ar71xx/image/Makefile b/target/linux/ar71xx/image/Makefile
index fc932e6..59bc919 100644
--- a/target/linux/ar71xx/image/Makefile
+++ b/target/linux/ar71xx/image/Makefile
@@ -152,6 +152,14 @@ define Device/gl-ar150
endef
TARGET_DEVICES += gl-ar150
+define Device/gl-ar300
+ BOARDNAME = GL-AR300
+ IMAGE_SIZE = 16000k
+ CONSOLE = ttyS0,115200
+ MTDPARTS = spi0.0:256k(u-boot)ro,64k(u-boot-env)ro,16000k(firmware),64k(art)ro
+endef
+TARGET_DEVICES += gl-ar300
+
define Device/wndr3700
BOARDNAME = WNDR3700
NETGEAR_KERNEL_MAGIC = 0x33373030
diff --git a/target/linux/ar71xx/patches-3.18/912-MIPS-ath79-add-gl_ar300.patch b/target/linux/ar71xx/patches-3.18/912-MIPS-ath79-add-gl_ar300.patch
new file mode 100644
index 0000000..f7cfb57
--- /dev/null
+++ b/target/linux/ar71xx/patches-3.18/912-MIPS-ath79-add-gl_ar300.patch
@@ -0,0 +1,39 @@
+--- a/arch/mips/ath79/Kconfig
++++ b/arch/mips/ath79/Kconfig
+@@ -543,6 +543,16 @@ config ATH79_MACH_GL_AR150
+ select ATH79_DEV_USB
+ select ATH79_DEV_WMAC
+
++config ATH79_MACH_GL_AR300
++ bool "GL_AR300 support"
++ select SOC_AR934X
++ select ATH79_DEV_ETH
++ select ATH79_DEV_GPIO_BUTTONS
++ select ATH79_DEV_LEDS_GPIO
++ select ATH79_DEV_M25P80
++ select ATH79_DEV_USB
++ select ATH79_DEV_WMAC
++
+ config ATH79_MACH_EAP300V2
+ bool "EnGenius EAP300 v2 support"
+ select SOC_AR934X
+--- a/arch/mips/ath79/Makefile
++++ b/arch/mips/ath79/Makefile
+@@ -79,6 +79,7 @@ obj-$(CONFIG_ATH79_MACH_EPG5000) += mach
+ obj-$(CONFIG_ATH79_MACH_ESR1750) += mach-esr1750.o
+ obj-$(CONFIG_ATH79_MACH_F9K1115V2) += mach-f9k1115v2.o
+ obj-$(CONFIG_ATH79_MACH_GL_AR150) += mach-gl-ar150.o
++obj-$(CONFIG_ATH79_MACH_GL_AR300) += mach-gl-ar300.o
+ obj-$(CONFIG_ATH79_MACH_GL_INET) += mach-gl-inet.o
+ obj-$(CONFIG_ATH79_MACH_GS_MINIBOX_V1) += mach-gs-minibox-v1.o
+ obj-$(CONFIG_ATH79_MACH_GS_OOLITE) += mach-gs-oolite.o
+--- a/arch/mips/ath79/machtypes.h
++++ b/arch/mips/ath79/machtypes.h
+@@ -68,6 +68,7 @@ enum ath79_mach_type {
+ ATH79_MACH_EPG5000, /* EnGenius EPG5000 */
+ ATH79_MACH_F9K1115V2, /* Belkin AC1750DB */
+ ATH79_MACH_GL_AR150, /* GL-AR150 support */
++ ATH79_MACH_GL_AR300, /* GL-AR300 */
+ ATH79_MACH_GL_INET, /* GL-CONNECT GL-INET */
+ ATH79_MACH_GS_MINIBOX_V1, /* Gainstrong MiniBox V1.0 */
+ ATH79_MACH_GS_OOLITE, /* GS OOLITE V1.0 */
--
1.9.1
_______________________________________________
openwrt-devel mailing list
openwrt-devel at lists.openwrt.org
https://lists.openwrt.org/cgi-bin/mailman/listinfo/openwrt-devel
More information about the openwrt-devel
mailing list