[OpenWrt-Devel] [PATCH] ramips: add support for Planex CS-QR10
John Crispin
john at phrozen.org
Thu Apr 21 15:36:17 EDT 2016
Hi,
this one also fails to apply. please rebase/resend
JOhn
On 12/04/2016 14:16, YuheiOKAWA wrote:
> CS-QR10 is MT7620A based IP Camera.
>
> the camera and sound does not work with kernel 4.4.
> - camera chip is sn9c291.
> - sound chip is wm8960.
>
> Signed-off-by: YuheiOKAWA <tochiro.srchack at gmail.com>
> ---
> target/linux/ramips/base-files/etc/board.d/01_leds | 3 +-
> .../linux/ramips/base-files/etc/board.d/02_network | 1 +
> target/linux/ramips/base-files/etc/diag.sh | 1 +
> target/linux/ramips/base-files/lib/ramips.sh | 3 +
> .../ramips/base-files/lib/upgrade/platform.sh | 1 +
> target/linux/ramips/dts/CS-QR10.dts | 163 +++++++++++++++++++++
> target/linux/ramips/image/mt7620.mk | 2 +
> target/linux/ramips/mt7620/profiles/planex.mk | 19 +++
> 8 files changed, 192 insertions(+), 1 deletion(-)
> create mode 100644 target/linux/ramips/dts/CS-QR10.dts
> create mode 100644 target/linux/ramips/mt7620/profiles/planex.mk
>
> diff --git a/target/linux/ramips/base-files/etc/board.d/01_leds b/target/linux/ramips/base-files/etc/board.d/01_leds
> index 5816e60..e319f36 100755
> --- a/target/linux/ramips/base-files/etc/board.d/01_leds
> +++ b/target/linux/ramips/base-files/etc/board.d/01_leds
> @@ -30,7 +30,8 @@ br-6475nd|\
> mzk-w300nh2)
> set_wifi_led "$board:amber:wlan"
> ;;
> -a5-v11)
> +a5-v11|\
> +cs-qr10)
> ucidef_set_led_default "power" "POWER" "$board:red:power" "1"
> ;;
> ai-br100)
> diff --git a/target/linux/ramips/base-files/etc/board.d/02_network b/target/linux/ramips/base-files/etc/board.d/02_network
> index 4b65d36..416b13c 100755
> --- a/target/linux/ramips/base-files/etc/board.d/02_network
> +++ b/target/linux/ramips/base-files/etc/board.d/02_network
> @@ -159,6 +159,7 @@ ramips_setup_interfaces()
> ucidef_add_switch "switch0" \
> "0:lan" "1:lan" "2:lan" "3:lan" "4:wan" "9 at eth0"
> ;;
> + cs-qr10|\
> d105|\
> hpm|\
> na930|\
> diff --git a/target/linux/ramips/base-files/etc/diag.sh b/target/linux/ramips/base-files/etc/diag.sh
> index daa7fb1..233d15c 100644
> --- a/target/linux/ramips/base-files/etc/diag.sh
> +++ b/target/linux/ramips/base-files/etc/diag.sh
> @@ -32,6 +32,7 @@ get_status_led() {
> status_led="$board:green:power"
> ;;
> a5-v11|\
> + cs-qr10|\
> d105|\
> dcs-930l-b1|\
> ex2700|\
> diff --git a/target/linux/ramips/base-files/lib/ramips.sh b/target/linux/ramips/base-files/lib/ramips.sh
> index 5f1df7b..2df2591 100755
> --- a/target/linux/ramips/base-files/lib/ramips.sh
> +++ b/target/linux/ramips/base-files/lib/ramips.sh
> @@ -88,6 +88,9 @@ ramips_board_detect() {
> *"CF-WR800N")
> name="cf-wr800n"
> ;;
> + *"CS-QR10")
> + name="cs-qr10"
> + ;;
> *"CY-SWR1100")
> name="cy-swr1100"
> ;;
> diff --git a/target/linux/ramips/base-files/lib/upgrade/platform.sh b/target/linux/ramips/base-files/lib/upgrade/platform.sh
> index c329dce..af7fb12 100755
> --- a/target/linux/ramips/base-files/lib/upgrade/platform.sh
> +++ b/target/linux/ramips/base-files/lib/upgrade/platform.sh
> @@ -34,6 +34,7 @@ platform_check_image() {
> broadway|\
> carambola|\
> cf-wr800n|\
> + cs-qr10|\
> d105|\
> dap-1350|\
> db-wrt01|\
> diff --git a/target/linux/ramips/dts/CS-QR10.dts b/target/linux/ramips/dts/CS-QR10.dts
> new file mode 100644
> index 0000000..08299e3
> --- /dev/null
> +++ b/target/linux/ramips/dts/CS-QR10.dts
> @@ -0,0 +1,163 @@
> +/dts-v1/;
> +
> +/include/ "mt7620a.dtsi"
> +
> +/ {
> + compatible = "ralink,mt7620a-soc";
> + model = "Planex CS-QR10";
> +
> + palmbus at 10000000 {
> + gpio0: gpio at 600 {
> + status = "okay";
> + };
> +
> + gpio1: gpio at 638 {
> + status = "okay";
> + };
> +
> + gpio2: gpio at 660 {
> + status = "okay";
> + };
> +
> + gpio3: gpio at 688 {
> + status = "okay";
> + };
> +
> + i2c at 900 {
> + status = "okay";
> + };
> +
> + i2s: i2s at a00 {
> + status = "okay";
> + pinctrl-names = "default";
> + pinctrl-0 = <&pcm_i2s_pins>;
> + };
> +
> + spi at b00 {
> + status = "okay";
> +
> + m25p80 at 0 {
> + #address-cells = <1>;
> + #size-cells = <1>;
> + compatible = "jedec,spi-nor";
> + reg = <0 0>;
> + linux,modalias = "m25p80", "mx25l6405d";
> + spi-max-frequency = <10000000>;
> +
> + partition at 0 {
> + label = "u-boot";
> + reg = <0x0 0x30000>;
> + read-only;
> + };
> +
> + partition at 30000 {
> + label = "u-boot-env";
> + reg = <0x30000 0x10000>;
> + read-only;
> + };
> +
> + factory: partition at 40000 {
> + label = "factory";
> + reg = <0x40000 0x10000>;
> + read-only;
> + };
> +
> + partition at 50000 {
> + label = "firmware";
> + reg = <0x50000 0x7b0000>;
> + };
> + };
> + };
> +
> + pcm at 2000 {
> + status = "okay";
> + };
> +
> + gdma at 2800 {
> + status = "okay";
> + };
> + };
> +
> + pinctrl {
> + state_default: pinctrl0 {
> + gpio {
> + ralink,group = "spi refclk", "rgmii1";
> + ralink,function = "gpio";
> + };
> + wdt {
> + ralink,group = "wdt";
> + ralink,function = "wdt refclk";
> + };
> + };
> + };
> +
> + ethernet at 10100000 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&ephy_pins>;
> + mtd-mac-address = <&factory 0x4>;
> + mediatek,portmap = "llllw";
> + };
> +
> + gsw at 10110000 {
> + ralink,port4 = "ephy";
> + };
> +
> + sdhci at 10130000 {
> + status = "okay";
> + };
> +
> + ehci at 101c0000 {
> + status = "okay";
> + };
> +
> + ohci at 101c1000 {
> + status = "okay";
> + };
> +
> + wmac at 10180000 {
> + ralink,mtd-eeprom = <&factory 0>;
> + };
> +
> + pcie at 10140000 {
> + status = "okay";
> + };
> +
> + sound {
> + compatible = "mediatek,mt7620-audio-wm8960";
> + model = "mt7620-wm8960";
> + i2s-controller = <&i2s>;
> + audio-routing =
> + "Ext Spk", "SPK_LP",
> + "Ext Spk", "SPK_LN",
> + "Ext Spk", "SPK_RP",
> + "Ext Spk", "SPK_RN";
> + };
> +
> + gpio-leds {
> + compatible = "gpio-leds";
> +
> + power {
> + label = "cs-qr10:red:power";
> + gpios = <&gpio1 4 1>;
> + };
> + };
> +
> + gpio-keys-polled {
> + compatible = "gpio-keys-polled";
> + #address-cells = <1>;
> + #size-cells = <0>;
> + poll-interval = <20>;
> +
> + s1 {
> + label = "reset";
> + gpios = <&gpio1 1 1>;
> + linux,code = <0x198>;
> + };
> +
> + s2 {
> + label = "wps";
> + gpios = <&gpio1 3 1>;
> + linux,code = <0x211>;
> + };
> + };
> +};
> diff --git a/target/linux/ramips/image/mt7620.mk b/target/linux/ramips/image/mt7620.mk
> index 18cd20a..2055116 100644
> --- a/target/linux/ramips/image/mt7620.mk
> +++ b/target/linux/ramips/image/mt7620.mk
> @@ -82,6 +82,7 @@ whr_1166d_mtd_size=15400960
> Image/Build/Profile/WHR1166D=$(call BuildFirmware/CustomFlash/$(1),$(1),whr-1166d,WHR-1166D,$(whr_1166d_mtd_size))
> dlink810l_mtd_size=6881280
> Image/Build/Profile/CF-WR800N=$(call BuildFirmware/Default8M/$(1),$(1),cf-wr800n,CF-WR800N)
> +Image/Build/Profile/CS-QR10=$(call BuildFirmware/Default8M/$(1),$(1),cs-qr10,CS-QR10)
> Image/Build/Profile/DIR-810L=$(call BuildFirmware/CustomFlash/$(1),$(1),dir-810l,DIR-810L,$(dlink810l_mtd_size))
> na930_mtd_size=20971520
> Image/Build/Profile/NA930=$(call BuildFirmware/CustomFlash/$(1),$(1),na930,NA930,$(na930_mtd_size))
> @@ -124,6 +125,7 @@ define Image/Build/Profile/Default
> $(call Image/Build/Profile/MT7620a_V22SG,$(1))
> $(call Image/Build/Profile/AI-BR100,$(1))
> $(call Image/Build/Profile/CF-WR800N,$(1))
> + $(call Image/Build/Profile/CS-QR10,$(1))
> $(call Image/Build/Profile/RP-N53,$(1))
> $(call Image/Build/Profile/DIR-810L,$(1))
> $(call Image/Build/Profile/WHR300HP2,$(1))
> diff --git a/target/linux/ramips/mt7620/profiles/planex.mk b/target/linux/ramips/mt7620/profiles/planex.mk
> new file mode 100644
> index 0000000..9d99cac
> --- /dev/null
> +++ b/target/linux/ramips/mt7620/profiles/planex.mk
> @@ -0,0 +1,19 @@
> +#
> +# Copyright (C) 2015 OpenWrt.org
> +#
> +# This is free software, licensed under the GNU General Public License v2.
> +# See /LICENSE for more information.
> +#
> +
> +define Profile/CS-QR10
> + NAME:=Planex CS-QR10
> + PACKAGES:=\
> + kmod-usb-core kmod-usb2 kmod-usb-ohci \
> + kmod-i2c-core kmod-i2c-ralink kmod-sound-core kmod-sound-mtk \
> + kmod-sdhci-mt7620
> +endef
> +
> +define Profile/CS-QR10/Description
> + Package set optimized for the Planex CS-QR10.
> +endef
> +$(eval $(call Profile,CS-QR10))
>
_______________________________________________
openwrt-devel mailing list
openwrt-devel at lists.openwrt.org
https://lists.openwrt.org/cgi-bin/mailman/listinfo/openwrt-devel
More information about the openwrt-devel
mailing list