[OpenWrt-Devel] [PATCH] ramips: add support for Planex MZK-EX300NP
John Crispin
john at phrozen.org
Thu Apr 21 15:30:30 EDT 2016
Hi,
fails to apply for some reason, please rebase and resend. there is one
small nitpick inline.
On 14/04/2016 16:59, YuheiOKAWA wrote:
> MZK-EX300NP is MT7620A based wifi repeater.
> Built-in power supply.
> 64MiB RAM, 8MiB SPI Flash, non Wired Ethernet.
>
> Signed-off-by: YuheiOKAWA <tochiro.srchack at gmail.com>
> ---
> target/linux/ramips/base-files/etc/board.d/01_leds | 1 +
> .../linux/ramips/base-files/etc/board.d/02_network | 1 +
> target/linux/ramips/base-files/etc/diag.sh | 1 +
> target/linux/ramips/base-files/lib/ramips.sh | 3 +
> .../ramips/base-files/lib/upgrade/platform.sh | 1 +
> target/linux/ramips/dts/MZK-EX300NP.dts | 132 +++++++++++++++++++++
> target/linux/ramips/image/mt7620.mk | 2 +
> target/linux/ramips/mt7620/profiles/planex.mk | 16 +++
> 8 files changed, 157 insertions(+)
> create mode 100644 target/linux/ramips/dts/MZK-EX300NP.dts
> create mode 100644 target/linux/ramips/mt7620/profiles/planex.mk
>
> diff --git a/target/linux/ramips/base-files/etc/board.d/01_leds b/target/linux/ramips/base-files/etc/board.d/01_leds
> index 5816e60..e8305d0 100755
> --- a/target/linux/ramips/base-files/etc/board.d/01_leds
> +++ b/target/linux/ramips/base-files/etc/board.d/01_leds
> @@ -118,6 +118,7 @@ dir-615-h1)
> ucidef_set_led_default "status" "Status LED (amber)" "$board:amber:status" "0"
> set_wifi_led "rt2800pci-phy0::radio"
> ;;
> +mzk-ex300np|\
> dir-620-d1)
> set_wifi_led "$board:green:wifi"
> ;;
> diff --git a/target/linux/ramips/base-files/etc/board.d/02_network b/target/linux/ramips/base-files/etc/board.d/02_network
> index 4b65d36..db2e6d9 100755
> --- a/target/linux/ramips/base-files/etc/board.d/02_network
> +++ b/target/linux/ramips/base-files/etc/board.d/02_network
> @@ -160,6 +160,7 @@ ramips_setup_interfaces()
> "0:lan" "1:lan" "2:lan" "3:lan" "4:wan" "9 at eth0"
> ;;
> d105|\
> + mzk-ex300np|\
this should be below hpm and not above it
John
> hpm|\
> na930|\
> wli-tx4-ag300n)
> diff --git a/target/linux/ramips/base-files/etc/diag.sh b/target/linux/ramips/base-files/etc/diag.sh
> index daa7fb1..8692da9 100644
> --- a/target/linux/ramips/base-files/etc/diag.sh
> +++ b/target/linux/ramips/base-files/etc/diag.sh
> @@ -151,6 +151,7 @@ get_status_led() {
> whr-600d)
> status_led="$board:orange:wifi"
> ;;
> + mzk-ex300np|\
> rt-n10-plus|\
> tew-691gr|\
> tew-692gr|\
> diff --git a/target/linux/ramips/base-files/lib/ramips.sh b/target/linux/ramips/base-files/lib/ramips.sh
> index 5f1df7b..b1cb2eb 100755
> --- a/target/linux/ramips/base-files/lib/ramips.sh
> +++ b/target/linux/ramips/base-files/lib/ramips.sh
> @@ -292,6 +292,9 @@ ramips_board_detect() {
> *"MZK-DP150N")
> name="mzk-dp150n"
> ;;
> + *"MZK-EX300NP")
> + name="mzk-ex300np"
> + ;;
> *"MZK-W300NH2"*)
> name="mzk-w300nh2"
> ;;
> diff --git a/target/linux/ramips/base-files/lib/upgrade/platform.sh b/target/linux/ramips/base-files/lib/upgrade/platform.sh
> index c329dce..d8e6f66 100755
> --- a/target/linux/ramips/base-files/lib/upgrade/platform.sh
> +++ b/target/linux/ramips/base-files/lib/upgrade/platform.sh
> @@ -87,6 +87,7 @@ platform_check_image() {
> mr-102n|\
> mt7628|\
> mzk-dp150n|\
> + mzk-ex300np|\
> mzk-w300nh2|\
> mzk-wdpr|\
> nbg-419n|\
> diff --git a/target/linux/ramips/dts/MZK-EX300NP.dts b/target/linux/ramips/dts/MZK-EX300NP.dts
> new file mode 100644
> index 0000000..51e87ad
> --- /dev/null
> +++ b/target/linux/ramips/dts/MZK-EX300NP.dts
> @@ -0,0 +1,132 @@
> +/dts-v1/;
> +
> +/include/ "mt7620a.dtsi"
> +
> +/ {
> + compatible = "ralink,mt7620a-soc";
> + model = "Planex MZK-EX300NP";
> +
> + palmbus at 10000000 {
> + gpio1: gpio at 638 {
> + status = "okay";
> + };
> +
> + gpio3: gpio at 688 {
> + status = "okay";
> + };
> +
> + spi at b00 {
> + status = "okay";
> +
> + m25p80 at 0 {
> + #address-cells = <1>;
> + #size-cells = <1>;
> + compatible = "jedec,spi-nor";
> + reg = <0 0>;
> + linux,modalias = "m25p80", "w25q64";
> + spi-max-frequency = <10000000>;
> +
> + partition at 0 {
> + label = "u-boot";
> + reg = <0x0 0x30000>;
> + read-only;
> + };
> +
> + partition at 30000 {
> + label = "u-boot-env";
> + reg = <0x30000 0x10000>;
> + read-only;
> + };
> +
> + factory: partition at 40000 {
> + label = "factory";
> + reg = <0x40000 0x10000>;
> + read-only;
> + };
> +
> + partition at 50000 {
> + label = "firmware";
> + reg = <0x50000 0x730000>;
> + };
> +
> + partition at 780000 {
> + label = "Udata";
> + reg = <0x780000 0x80000>;
> + };
> + };
> + };
> + };
> +
> + pinctrl {
> + state_default: pinctrl0 {
> + gpio {
> + ralink,group = "i2c", "spi refclk", "rgmii1", "wled";
> + ralink,function = "gpio";
> + };
> + };
> + };
> +
> + ethernet at 10100000 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&ephy_pins>;
> + mtd-mac-address = <&factory 0x4>;
> + mediatek,portmap = "llllw";
> + };
> +
> + wmac at 10180000 {
> + ralink,mtd-eeprom = <&factory 0>;
> + };
> +
> + gpio-leds {
> + compatible = "gpio-leds";
> +
> + wifi {
> + label = "mzk-ex300np:green:wifi";
> + gpios = <&gpio3 0 0>;
> + };
> +
> + wps {
> + label = "mzk-ex300np:green:wps";
> + gpios = <&gpio1 5 0>;
> + };
> +
> + rep {
> + label = "mzk-ex300np:blue:rep";
> + gpios = <&gpio1 4 1>;
> + };
> +
> + wifi1 {
> + label = "mzk-ex300np:blue:wifi1";
> + gpios = <&gpio1 1 1>;
> + };
> +
> + wifi2 {
> + label = "mzk-ex300np:blue:wifi2";
> + gpios = <&gpio1 2 1>;
> + };
> +
> + wifi3 {
> + label = "mzk-ex300np:blue:wifi3";
> + gpios = <&gpio1 0 1>;
> + };
> + };
> +
> + gpio-keys-polled {
> + compatible = "gpio-keys-polled";
> + #address-cells = <1>;
> + #size-cells = <0>;
> + poll-interval = <20>;
> +
> + reset {
> + label = "reset";
> + gpios = <&gpio0 1 1>;
> + linux,code = <0x198>;
> + };
> +
> + wps {
> + label = "wps";
> + gpios = <&gpio1 3 0>;
> + linux,code = <0x211>;
> + };
> + };
> +};
> diff --git a/target/linux/ramips/image/mt7620.mk b/target/linux/ramips/image/mt7620.mk
> index 18cd20a..3c9d6ce 100644
> --- a/target/linux/ramips/image/mt7620.mk
> +++ b/target/linux/ramips/image/mt7620.mk
> @@ -87,6 +87,7 @@ na930_mtd_size=20971520
> Image/Build/Profile/NA930=$(call BuildFirmware/CustomFlash/$(1),$(1),na930,NA930,$(na930_mtd_size))
> Image/Build/Profile/DB-WRT01=$(call BuildFirmware/Default8M/$(1),$(1),db-wrt01,DB-WRT01)
> Image/Build/Profile/MZK-750DHP=$(call BuildFirmware/Default8M/$(1),$(1),mzk-750dhp,MZK-750DHP)
> +Image/Build/Profile/MZK-EX300NP=$(call BuildFirmware/Default8M/$(1),$(1),mzk-ex300np,MZK-EX300NP)
> Image/Build/Profile/HC5661=$(call BuildFirmware/Default16M/$(1),$(1),hc5661,HC5661)
> Image/Build/Profile/HC5761=$(call BuildFirmware/Default16M/$(1),$(1),hc5761,HC5761)
> Image/Build/Profile/HC5861=$(call BuildFirmware/Default16M/$(1),$(1),hc5861,HC5861)
> @@ -131,6 +132,7 @@ define Image/Build/Profile/Default
> $(call Image/Build/Profile/WHR1166D,$(1))
> $(call Image/Build/Profile/DB-WRT01,$(1))
> $(call Image/Build/Profile/MZK-750DHP,$(1))
> + $(call Image/Build/Profile/MZK-EX300NP,$(1))
> $(call Image/Build/Profile/NA930,$(1))
> $(call Image/Build/Profile/HC5661,$(1))
> $(call Image/Build/Profile/HC5761,$(1))
> diff --git a/target/linux/ramips/mt7620/profiles/planex.mk b/target/linux/ramips/mt7620/profiles/planex.mk
> new file mode 100644
> index 0000000..79bfbdb
> --- /dev/null
> +++ b/target/linux/ramips/mt7620/profiles/planex.mk
> @@ -0,0 +1,16 @@
> +#
> +# Copyright (C) 2015 OpenWrt.org
> +#
> +# This is free software, licensed under the GNU General Public License v2.
> +# See /LICENSE for more information.
> +#
> +
> +define Profile/MZK-EX300NP
> + NAME:=Planex MZK-EX300NP
> + PACKAGES:=
> +endef
> +
> +define Profile/MZK-EX300NP/Description
> + Package set optimized for the Planex MZK-EX300NP.
> +endef
> +$(eval $(call Profile,MZK-EX300NP))
>
_______________________________________________
openwrt-devel mailing list
openwrt-devel at lists.openwrt.org
https://lists.openwrt.org/cgi-bin/mailman/listinfo/openwrt-devel
More information about the openwrt-devel
mailing list