[OpenWrt-Devel] [PATCH 02/16] ar71xx: add kernel support for the OpenMesh OM5P-AC board
Sven Eckelmann
sven.eckelmann at open-mesh.com
Tue Apr 5 11:17:47 EDT 2016
From: Sven Eckelmann <sven.eckelmann at open-mesh.com>
Signed-off-by: Sven Eckelmann <sven.eckelmann at open-mesh.com>
---
target/linux/ar71xx/config-4.1 | 1 +
target/linux/ar71xx/config-4.4 | 1 +
.../ar71xx/files/arch/mips/ath79/Kconfig.openwrt | 9 +
target/linux/ar71xx/files/arch/mips/ath79/Makefile | 1 +
.../ar71xx/files/arch/mips/ath79/mach-om5pac.c | 193 +++++++++++++++++++++
.../linux/ar71xx/files/arch/mips/ath79/machtypes.h | 1 +
6 files changed, 206 insertions(+)
create mode 100644 target/linux/ar71xx/files/arch/mips/ath79/mach-om5pac.c
diff --git a/target/linux/ar71xx/config-4.1 b/target/linux/ar71xx/config-4.1
index d6ad850..0ba1f53 100644
--- a/target/linux/ar71xx/config-4.1
+++ b/target/linux/ar71xx/config-4.1
@@ -109,6 +109,7 @@ CONFIG_ATH79_MACH_NBG460N=y
CONFIG_ATH79_MACH_NBG6716=y
CONFIG_ATH79_MACH_OM2P=y
CONFIG_ATH79_MACH_OM5P=y
+CONFIG_ATH79_MACH_OM5P_AC=y
CONFIG_ATH79_MACH_OMY_X1=y
CONFIG_ATH79_MACH_ONION_OMEGA=y
CONFIG_ATH79_MACH_PB42=y
diff --git a/target/linux/ar71xx/config-4.4 b/target/linux/ar71xx/config-4.4
index 49cecc5..5117829 100644
--- a/target/linux/ar71xx/config-4.4
+++ b/target/linux/ar71xx/config-4.4
@@ -112,6 +112,7 @@ CONFIG_ATH79_MACH_NBG460N=y
CONFIG_ATH79_MACH_NBG6716=y
CONFIG_ATH79_MACH_OM2P=y
CONFIG_ATH79_MACH_OM5P=y
+CONFIG_ATH79_MACH_OM5P_AC=y
CONFIG_ATH79_MACH_OMY_X1=y
CONFIG_ATH79_MACH_ONION_OMEGA=y
CONFIG_ATH79_MACH_PB42=y
diff --git a/target/linux/ar71xx/files/arch/mips/ath79/Kconfig.openwrt b/target/linux/ar71xx/files/arch/mips/ath79/Kconfig.openwrt
index f47f1b9..b12c42a 100644
--- a/target/linux/ar71xx/files/arch/mips/ath79/Kconfig.openwrt
+++ b/target/linux/ar71xx/files/arch/mips/ath79/Kconfig.openwrt
@@ -861,6 +861,15 @@ config ATH79_MACH_OM5P
select ATH79_DEV_M25P80
select ATH79_DEV_WMAC
+config ATH79_MACH_OM5P_AC
+ bool "OpenMesh OM5P-AC board support"
+ select SOC_QCA955X
+ select ATH79_DEV_AP9X_PCI if PCI
+ select ATH79_DEV_ETH
+ select ATH79_DEV_LEDS_GPIO
+ select ATH79_DEV_M25P80
+ select ATH79_DEV_WMAC
+
config ATH79_MACH_OMY_X1
bool "OMYlink OMY X1 support"
select SOC_AR934X
diff --git a/target/linux/ar71xx/files/arch/mips/ath79/Makefile b/target/linux/ar71xx/files/arch/mips/ath79/Makefile
index 74376b2..484dda0 100644
--- a/target/linux/ar71xx/files/arch/mips/ath79/Makefile
+++ b/target/linux/ar71xx/files/arch/mips/ath79/Makefile
@@ -115,6 +115,7 @@ obj-$(CONFIG_ATH79_MACH_MZK_W300NH) += mach-mzk-w300nh.o
obj-$(CONFIG_ATH79_MACH_NBG460N) += mach-nbg460n.o
obj-$(CONFIG_ATH79_MACH_OM2P) += mach-om2p.o
obj-$(CONFIG_ATH79_MACH_OM5P) += mach-om5p.o
+obj-$(CONFIG_ATH79_MACH_OM5P_AC) += mach-om5pac.o
obj-$(CONFIG_ATH79_MACH_OMY_X1) += mach-omy-x1.o
obj-$(CONFIG_ATH79_MACH_ONION_OMEGA) += mach-onion-omega.o
obj-$(CONFIG_ATH79_MACH_PB42) += mach-pb42.o
diff --git a/target/linux/ar71xx/files/arch/mips/ath79/mach-om5pac.c b/target/linux/ar71xx/files/arch/mips/ath79/mach-om5pac.c
new file mode 100644
index 0000000..f6974af
--- /dev/null
+++ b/target/linux/ar71xx/files/arch/mips/ath79/mach-om5pac.c
@@ -0,0 +1,193 @@
+/*
+ * OpenMesh OM5P-AC support
+ *
+ * Copyright (C) 2013 Marek Lindner <marek at open-mesh.com>
+ * Copyright (C) 2014 Sven Eckelmann <sven at open-mesh.com>
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License version 2 as published
+ * by the Free Software Foundation.
+ */
+
+#include <linux/gpio.h>
+#include <linux/mtd/mtd.h>
+#include <linux/mtd/partitions.h>
+#include <linux/platform_device.h>
+#include <linux/i2c.h>
+#include <linux/i2c-algo-bit.h>
+#include <linux/i2c-gpio.h>
+#include <linux/platform_data/phy-at803x.h>
+
+#include <asm/mach-ath79/ar71xx_regs.h>
+#include <asm/mach-ath79/ath79.h>
+
+#include "common.h"
+#include "dev-ap9x-pci.h"
+#include "dev-eth.h"
+#include "dev-leds-gpio.h"
+#include "dev-m25p80.h"
+#include "dev-wmac.h"
+#include "machtypes.h"
+#include "pci.h"
+
+#define OM5PAC_GPIO_LED_POWER 18
+#define OM5PAC_GPIO_LED_GREEN 21
+#define OM5PAC_GPIO_LED_RED 23
+#define OM5PAC_GPIO_LED_YELLOW 22
+#define OM5PAC_GPIO_LED_LAN 20
+#define OM5PAC_GPIO_LED_WAN 19
+#define OM5PAC_GPIO_I2C_SCL 12
+#define OM5PAC_GPIO_I2C_SDA 11
+
+#define OM5PAC_KEYS_POLL_INTERVAL 20 /* msecs */
+#define OM5PAC_KEYS_DEBOUNCE_INTERVAL (3 * OM5PAC_KEYS_POLL_INTERVAL)
+
+#define OM5PAC_WMAC_CALDATA_OFFSET 0x1000
+
+static struct gpio_led om5pac_leds_gpio[] __initdata = {
+ {
+ .name = "om5pac:blue:power",
+ .gpio = OM5PAC_GPIO_LED_POWER,
+ .active_low = 1,
+ }, {
+ .name = "om5pac:red:wifi",
+ .gpio = OM5PAC_GPIO_LED_RED,
+ .active_low = 1,
+ }, {
+ .name = "om5pac:yellow:wifi",
+ .gpio = OM5PAC_GPIO_LED_YELLOW,
+ .active_low = 1,
+ }, {
+ .name = "om5pac:green:wifi",
+ .gpio = OM5PAC_GPIO_LED_GREEN,
+ .active_low = 1,
+ }, {
+ .name = "om5pac:blue:lan",
+ .gpio = OM5PAC_GPIO_LED_LAN,
+ .active_low = 1,
+ }, {
+ .name = "om5pac:blue:wan",
+ .gpio = OM5PAC_GPIO_LED_WAN,
+ .active_low = 1,
+ }
+};
+
+static struct flash_platform_data om5pac_flash_data = {
+ .type = "mx25l12805d",
+};
+
+static struct i2c_gpio_platform_data om5pac_i2c_device_platdata = {
+ .sda_pin = OM5PAC_GPIO_I2C_SDA,
+ .scl_pin = OM5PAC_GPIO_I2C_SCL,
+ .udelay = 10,
+ .sda_is_open_drain = 1,
+ .scl_is_open_drain = 1,
+};
+
+static struct platform_device om5pac_i2c_device = {
+ .name = "i2c-gpio",
+ .id = 0,
+ .dev = {
+ .platform_data = &om5pac_i2c_device_platdata,
+ },
+};
+
+static struct i2c_board_info om5pac_i2c_devs[] __initdata = {
+ {
+ I2C_BOARD_INFO("tmp423", 0x4c),
+ },
+};
+
+static struct at803x_platform_data om5pac_at803x_data = {
+ .disable_smarteee = 1,
+ .enable_rgmii_rx_delay = 1,
+ .enable_rgmii_tx_delay = 1,
+};
+
+static struct mdio_board_info om5pac_mdio0_info[] = {
+ {
+ .bus_id = "ag71xx-mdio.0",
+ .phy_addr = 1,
+ .platform_data = &om5pac_at803x_data,
+ },
+ {
+ .bus_id = "ag71xx-mdio.0",
+ .phy_addr = 2,
+ .platform_data = &om5pac_at803x_data,
+ },
+};
+
+static void __init om5p_ac_setup_qca955x_eth_cfg(u32 mask,
+ unsigned int rxd,
+ unsigned int rxdv,
+ unsigned int txd,
+ unsigned int txe)
+{
+ void __iomem *base;
+ u32 t;
+
+ base = ioremap(QCA955X_GMAC_BASE, QCA955X_GMAC_SIZE);
+
+ t = mask;
+ t |= rxd << QCA955X_ETH_CFG_RXD_DELAY_SHIFT;
+ t |= rxdv << QCA955X_ETH_CFG_RDV_DELAY_SHIFT;
+ t |= txd << QCA955X_ETH_CFG_TXD_DELAY_SHIFT;
+ t |= txe << QCA955X_ETH_CFG_TXE_DELAY_SHIFT;
+
+ __raw_writel(t, base + QCA955X_GMAC_REG_ETH_CFG);
+
+ iounmap(base);
+}
+
+static void __init om5p_ac_setup(void)
+{
+ u8 *art = (u8 *)KSEG1ADDR(0x1fff0000);
+ u8 mac[6];
+
+ /* temperature sensor */
+ platform_device_register(&om5pac_i2c_device);
+ i2c_register_board_info(0, om5pac_i2c_devs,
+ ARRAY_SIZE(om5pac_i2c_devs));
+
+ ath79_gpio_output_select(OM5PAC_GPIO_LED_WAN, QCA955X_GPIO_OUT_GPIO);
+
+ ath79_register_m25p80(&om5pac_flash_data);
+ ath79_register_leds_gpio(-1, ARRAY_SIZE(om5pac_leds_gpio),
+ om5pac_leds_gpio);
+
+ ath79_init_mac(mac, art, 0x02);
+ ath79_register_wmac(art + OM5PAC_WMAC_CALDATA_OFFSET, mac);
+
+ om5p_ac_setup_qca955x_eth_cfg(QCA955X_ETH_CFG_RGMII_EN, 3, 3, 0, 0);
+ ath79_register_mdio(0, 0x0);
+
+ mdiobus_register_board_info(om5pac_mdio0_info,
+ ARRAY_SIZE(om5pac_mdio0_info));
+
+ ath79_init_mac(ath79_eth0_data.mac_addr, art, 0x00);
+ ath79_init_mac(ath79_eth1_data.mac_addr, art, 0x01);
+
+ /* GMAC0 is connected to the PHY1 */
+ ath79_eth0_data.phy_if_mode = PHY_INTERFACE_MODE_RGMII;
+ ath79_eth0_data.mii_bus_dev = &ath79_mdio0_device.dev;
+ ath79_eth0_data.phy_mask = BIT(1);
+ ath79_eth0_pll_data.pll_1000 = 0x82000101;
+ ath79_eth0_pll_data.pll_100 = 0x80000101;
+ ath79_eth0_pll_data.pll_10 = 0x80001313;
+ ath79_register_eth(0);
+
+ /* GMAC1 is connected to MDIO1 in SGMII mode */
+ ath79_eth1_data.phy_if_mode = PHY_INTERFACE_MODE_SGMII;
+ ath79_eth1_data.mii_bus_dev = &ath79_mdio0_device.dev;
+ ath79_eth1_data.phy_mask = BIT(2);
+ ath79_eth1_pll_data.pll_1000 = 0x03000101;
+ ath79_eth1_pll_data.pll_100 = 0x80000101;
+ ath79_eth1_pll_data.pll_10 = 0x80001313;
+ ath79_eth1_data.speed = SPEED_1000;
+ ath79_eth1_data.duplex = DUPLEX_FULL;
+ ath79_register_eth(1);
+
+ ath79_register_pci();
+}
+
+MIPS_MACHINE(ATH79_MACH_OM5P_AC, "OM5P-AC", "OpenMesh OM5P AC", om5p_ac_setup);
diff --git a/target/linux/ar71xx/files/arch/mips/ath79/machtypes.h b/target/linux/ar71xx/files/arch/mips/ath79/machtypes.h
index 307d2df..12e30c7 100644
--- a/target/linux/ar71xx/files/arch/mips/ath79/machtypes.h
+++ b/target/linux/ar71xx/files/arch/mips/ath79/machtypes.h
@@ -113,6 +113,7 @@ enum ath79_mach_type {
ATH79_MACH_OM2P_LC, /* OpenMesh OM2P-LC */
ATH79_MACH_OM2Pv2, /* OpenMesh OM2Pv2 */
ATH79_MACH_OM2P, /* OpenMesh OM2P */
+ ATH79_MACH_OM5P_AC, /* OpenMesh OM5P-AC */
ATH79_MACH_OM5P_AN, /* OpenMesh OM5P-AN */
ATH79_MACH_OM5P, /* OpenMesh OM5P */
ATH79_MACH_OMY_X1, /* OMYlink OMY-X1 */
--
2.8.0.rc3
_______________________________________________
openwrt-devel mailing list
openwrt-devel at lists.openwrt.org
https://lists.openwrt.org/cgi-bin/mailman/listinfo/openwrt-devel
More information about the openwrt-devel
mailing list