[OpenWrt-Devel] [PATCH] Add support for ZTE Q7
郭传鈜
gch981213 at gmail.com
Tue Mar 31 07:45:53 EDT 2015
Sorry I forgot to edit the title.This is a router with MT7620a SoC so
it belongs to ramips target.
2015-03-31 19:38 GMT+08:00 郭传鈜 <gch981213 at gmail.com>:
> ZTE Q7 is a wireless router with SD Card,USB,1 ethernet port and a battery.
> I can,t find any information about this router on ZTE's website.
> But I found this : http://en.cctairmobi.com/plus/list.php?tid=40
> This router is the same as ZTE Q7 and later I found that both routers are
> made by the same company:-D
>
> This patch adds support for it.
> Because there is only one port,I disabled VLAN and use eth0 as lan port.
> I could only create a sysupgrade firmware because I don't know how the
> orignal webpage check the uploaded image:-(
> Signed-off-by: 郭传鈜 <gch981213 at gmail.com>
>
> ---
> target/linux/ramips/base-files/etc/board.d/01_leds | 3 +
> .../linux/ramips/base-files/etc/board.d/02_network | 1 +
> target/linux/ramips/base-files/etc/diag.sh | 3 +
> target/linux/ramips/base-files/lib/ramips.sh | 3 +
> .../ramips/base-files/lib/upgrade/platform.sh | 1 +
> target/linux/ramips/dts/ZTE-Q7.dts | 111
> +++++++++++++++++++++
> target/linux/ramips/image/Makefile | 2 +
> 7 files changed, 124 insertions(+)
> create mode 100644 target/linux/ramips/dts/ZTE-Q7.dts
>
> diff --git a/target/linux/ramips/base-files/etc/board.d/01_leds
> b/target/linux/ramips/base-files/etc/board.d/01_leds
> index bfe1c0c..56ba3b7 100755
> --- a/target/linux/ramips/base-files/etc/board.d/01_leds
> +++ b/target/linux/ramips/base-files/etc/board.d/01_leds
> @@ -237,6 +237,9 @@ case $board in
> set_usb_led "lenovo:blue:usb"
> set_wifi_led "lenovo:blue:wifi"
> ;;
> + zte-q7)
> + set_wifi_led "zte:blue:status"
> + ;;
> esac
>
> board_config_flush
> diff --git a/target/linux/ramips/base-files/etc/board.d/02_network
> b/target/linux/ramips/base-files/etc/board.d/02_network
> index 89d1681..d4ec19d 100755
> --- a/target/linux/ramips/base-files/etc/board.d/02_network
> +++ b/target/linux/ramips/base-files/etc/board.d/02_network
> @@ -46,6 +46,7 @@ ramips_setup_interfaces()
> 3g150b | \
> 3g300m | \
> w150m | \
> + zte-q7 | \
> all0256n | \
> all5002 | \
> all5003 | \
> diff --git a/target/linux/ramips/base-files/etc/diag.sh
> b/target/linux/ramips/base-files/etc/diag.sh
> index 50b6ff2..5301593 100644
> --- a/target/linux/ramips/base-files/etc/diag.sh
> +++ b/target/linux/ramips/base-files/etc/diag.sh
> @@ -224,6 +224,9 @@ get_status_led() {
> y1s)
> status_led="lenovo:blue:power"
> ;;
> + zte-q7)
> + status_led="zte:red:status"
> + ;;
> esac
> }
>
> diff --git a/target/linux/ramips/base-files/lib/ramips.sh
> b/target/linux/ramips/base-files/lib/ramips.sh
> index 4527414..fc6eb37 100755
> --- a/target/linux/ramips/base-files/lib/ramips.sh
> +++ b/target/linux/ramips/base-files/lib/ramips.sh
> @@ -379,6 +379,9 @@ ramips_board_detect() {
> *"ZBT WR8305RT")
> name="wr8305rt"
> ;;
> + *"ZTE Q7")
> + name="zte-q7"
> + ;;
> *"Lenovo Y1")
> name="y1"
> ;;
> diff --git a/target/linux/ramips/base-files/lib/upgrade/platform.sh
> b/target/linux/ramips/base-files/lib/upgrade/platform.sh
> index fffbe72..a5773b5 100755
> --- a/target/linux/ramips/base-files/lib/upgrade/platform.sh
> +++ b/target/linux/ramips/base-files/lib/upgrade/platform.sh
> @@ -114,6 +114,7 @@ platform_check_image() {
> xiaomi-miwifi-mini |\
> y1 |\
> y1s |\
> + zte-q7 |\
> zbt-wa05)
> [ "$magic" != "27051956" ] && {
> echo "Invalid image type."
> diff --git a/target/linux/ramips/dts/ZTE-Q7.dts
> b/target/linux/ramips/dts/ZTE-Q7.dts
> new file mode 100644
> index 0000000..9efc35e
> --- /dev/null
> +++ b/target/linux/ramips/dts/ZTE-Q7.dts
> @@ -0,0 +1,111 @@
> +/dts-v1/;
> +
> +/include/ "mt7620a.dtsi"
> +
> +/ {
> + compatible = "ZTE-Q7", "ralink,mt7620a-soc";
> + model = "ZTE Q7";
> +
> + palmbus at 10000000 {
> +
> + gpio0: gpio at 600 {
> + status = "okay";
> + };
> +
> + gpio1: gpio at 638 {
> + status = "okay";
> + };
> +
> + spi at b00 {
> + status = "okay";
> +
> + m25p80 at 0 {
> + #address-cells = <1>;
> + #size-cells = <1>;
> + compatible = "en25q64";
> + reg = <0 0>;
> + linux,modalias = "m25p80", "en25q64";
> + spi-max-frequency = <10000000>;
> +
> + partition at 0 {
> + label = "u-boot";
> + reg = <0x0 0x30000>;
> + read-only;
> + };
> +
> + partition at 30000 {
> + label = "u-boot-env";
> + reg = <0x30000 0x10000>;
> + read-only;
> + };
> +
> + factory: partition at 40000 {
> + label = "factory";
> + reg = <0x40000 0x10000>;
> + read-only;
> + };
> +
> + partition at 50000 {
> + label = "firmware";
> + reg = <0x50000 0x7b0000>;
> + };
> + };
> + };
> + };
> +
> + pinctrl {
> + state_default: pinctrl0 {
> + gpio {
> + ralink,group = "i2c", "uartf", "rgmii1",
> "rgmii2", "ephy", "wled", "nd_sd";
> + ralink,function = "gpio";
> + };
> + };
> + };
> +
> + ethernet at 10100000 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&ephy_pins>;
> + mtd-mac-address = <&factory 0x4>;
> + ralink,port-map = "wllll";
> + };
> +
> + wmac at 10180000 {
> + ralink,mtd-eeprom = <&factory 0>;
> + };
> +
> + sdhci at 10130000 {
> + status = "okay";
> + };
> +
> + ehci at 101c0000 {
> + status = "okay";
> + };
> +
> + ohci at 101c1000 {
> + status = "okay";
> + };
> +
> + gpio-leds {
> + compatible = "gpio-leds";
> + statred {
> + label = "zte:red:status";
> + gpios = <&gpio0 13 1>;
> + };
> + statblue {
> + label = "zte:blue:status";
> + gpios = <&gpio0 9 1>;
> + };
> + };
> +
> + gpio-keys-polled {
> + compatible = "gpio-keys-polled";
> + #address-cells = <1>;
> + #size-cells = <0>;
> + poll-interval = <20>;
> + reset {
> + label = "reset";
> + gpios = <&gpio1 2 1>;
> + linux,code = <0x198>;
> + };
> + };
> +};
> diff --git a/target/linux/ramips/image/Makefile
> b/target/linux/ramips/image/Makefile
> index 45ae3a5..bc1fe181 100644
> --- a/target/linux/ramips/image/Makefile
> +++ b/target/linux/ramips/image/Makefile
> @@ -862,6 +862,7 @@ Image/Build/Profile/WR8305RT=$(call
> BuildFirmware/Default8M/$(1),$(1),wr8305rt,W
> Image/Build/Profile/WRTNODE=$(call
> BuildFirmware/Default16M/$(1),$(1),wrtnode,WRTNODE)
> Image/Build/Profile/WT3020=$(call
> BuildFirmware/PorayDualSize/$(1),$(1),wt3020,WT3020)
> Image/Build/Profile/XIAOMI-MIWIFI-MINI=$(call
> BuildFirmware/Default16M/$(1),$(1),xiaomi-miwifi-mini,XIAOMI-MIWIFI-MINI)
> +Image/Build/Profile/ZTE-Q7=$(call
> BuildFirmware/Default8M/$(1),$(1),zte-q7,ZTE-Q7)
> Image/Build/Profile/ZBT-WA05=$(call
> BuildFirmware/Default8M/$(1),$(1),zbt-wa05,ZBT-WA05)
> Image/Build/Profile/ArcherC20i=$(call
> BuildFirmware/Tplink/$(1),$(1),ArcherC20i,ArcherC20i)
>
> @@ -891,6 +892,7 @@ define Image/Build/Profile/Default
> $(call Image/Build/Profile/WRTNODE,$(1))
> $(call Image/Build/Profile/WT3020,$(1))
> $(call Image/Build/Profile/XIAOMI-MIWIFI-MINI,$(1))
> + $(call Image/Build/Profile/ZTE-Q7,$(1))
> $(call Image/Build/Profile/ZBT-WA05,$(1))
> $(call Image/Build/Profile/ArcherC20i,$(1))
> endef
> --
> 2.1.0
>
>
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://lists.infradead.org/pipermail/openwrt-devel/attachments/20150331/707a9120/attachment.htm>
-------------- next part --------------
_______________________________________________
openwrt-devel mailing list
openwrt-devel at lists.openwrt.org
https://lists.openwrt.org/cgi-bin/mailman/listinfo/openwrt-devel
More information about the openwrt-devel
mailing list