[PATCH-22.03 02/10] ipq40xx: Add subtarget for Google WiFi (Gale)
openwrt at aiyionpri.me
openwrt at aiyionpri.me
Fri Apr 7 06:23:40 PDT 2023
From: Brian Norris <computersforpeace at gmail.com>
Google WiFi (codename: Gale) is an IPQ4019-based AP, with 2 Ethernet
ports, 2x2 2.4+5GHz WiFi, 512 MB RAM, 4 GB eMMC, and a USB type C port.
In its stock configuration, it runs a Chromium OS-based system, but you
wouldn't know it, since you can only manage it via a "cloud" +
mobile-app system.
The "v2" label is coded into the bootloader, which prefers the
"google,gale-v2" compatible string. I believe "v1" must have been
pre-release hardware.
Note: this is *not* the Google Nest WiFi, released in 2019.
I include "factory.bin" support, where we generate a GPT-based disk
image with 2 partitions -- a kernel partition (using the custom "Chrome
OS kernel" GUID type) and a root filesystem partition. See below for
flashing instructions.
Sysupgrade is supported via recent emmc_do_upgrade() helper.
This is a subtarget because it enables different features
(FEATURES=boot-part rootfs-part) whose configurations don't make sense
in the "generic" target, and because it builds in a few USB drivers,
which are necessary for installation (installation is performed by
booting from USB storage, and so these drivers cannot be built as
modules, since we need to load modules from USB storage).
Flashing instructions
=====================
Documented here:
https://openwrt.org/inbox/toh/google/google_wifi
Note this requires booting from USB storage.
Features
========
I've tested:
* Ethernet, both WAN and LAN ports
* eMMC
* USB-C (hub, power-delivery, peripherals)
* LED0 (R/G/B)
* WiFi (limited testing)
* SPI flash
* Serial console: once in developer mode, console can be accessed via
the USB-C port with SuzyQable, or other similar "Closed Case
Debugging" tools:
https://chromium.googlesource.com/chromiumos/third_party/hdctools/+/master/docs/ccd.md#suzyq-suzyqable
* Sysupgrade
Not tested:
* TPM
Known not working:
* Reboot: this requires some additional TrustZone / SCM
configuration to disable Qualcomm's SDI. I have a proposal upstream,
and based on IRC chats, this might be acceptable with additional DT
logic:
[RFC PATCH] firmware: qcom_scm: disable SDI at boot
https://lore.kernel.org/linux-arm-msm/20200721080054.2803881-1-computersforpeace@gmail.com/
* SMP: enabling secondary CPUs doesn't currently work using the stock
bootloader, as the qcom_scm driver assumes newer features than this
TrustZone firmware has. I posted notes here:
[RFC] qcom_scm: IPQ4019 firmware does not support atomic API?
https://lore.kernel.org/linux-arm-msm/20200913201608.GA3162100@bDebian/
* There's a single external button, and a few useful internal GPIO
switches. I haven't hooked them up.
The first two are fixed with subsequent commits.
Additional notes
================
Much of the DTS is pulled from the Chrome OS kernel 3.18 branch, which
the manufacturer image uses.
Note: the manufacturer bootloader knows how to patch in calibration data
via the wifi{0,1} aliases in the DTB, so while these properties aren't
present in the DTS, they are available at runtime:
# ls -l
/sys/firmware/devicetree/base/soc/wifi at a*/qcom,ath10k-pre-calibration-data
-r--r--r-- 1 root root 12064 Jul 15 19:11 /sys/firmware/devicetree/base/soc/wifi at a000000/qcom,ath10k-pre-calibration-data
-r--r--r-- 1 root root 12064 Jul 15 19:11 /sys/firmware/devicetree/base/soc/wifi at a800000/qcom,ath10k-pre-calibration-data
Ethernet MAC addresses are similarly patched in via the ethernet{0,1} aliases.
Signed-off-by: Brian Norris <computersforpeace at gmail.com>
(updated 901 - x1pro moved in the process)
Signed-off-by: Christian Lamparter <chunkeey at gmail.com>
(cherry picked from commit f1c041e34f9742fcdd0c8c65f69888d3ec580541)
Signed-off-by: Jan-Niklas Burfeind <git at aiyionpri.me>
(updated 901 - fixed offset, after missing drop commit)
---
target/linux/ipq40xx/Makefile | 2 +-
.../ipq40xx/base-files/etc/board.d/02_network | 1 +
.../base-files/lib/upgrade/platform.sh | 10 +-
target/linux/ipq40xx/chromium/config-default | 10 +
target/linux/ipq40xx/chromium/target.mk | 2 +
.../arch/arm/boot/dts/qcom-ipq4019-wifi.dts | 413 ++++++++++++++++++
target/linux/ipq40xx/image/chromium.mk | 14 +
.../901-arm-boot-add-dts-files.patch | 5 +-
8 files changed, 453 insertions(+), 4 deletions(-)
create mode 100644 target/linux/ipq40xx/chromium/config-default
create mode 100644 target/linux/ipq40xx/chromium/target.mk
create mode 100644 target/linux/ipq40xx/files/arch/arm/boot/dts/qcom-ipq4019-wifi.dts
diff --git a/target/linux/ipq40xx/Makefile b/target/linux/ipq40xx/Makefile
index b704e1b54e..6051c82945 100644
--- a/target/linux/ipq40xx/Makefile
+++ b/target/linux/ipq40xx/Makefile
@@ -6,7 +6,7 @@ BOARDNAME:=Qualcomm Atheros IPQ40XX
FEATURES:=squashfs fpu ramdisk nand
CPU_TYPE:=cortex-a7
CPU_SUBTYPE:=neon-vfpv4
-SUBTARGETS:=generic mikrotik
+SUBTARGETS:=generic chromium mikrotik
KERNEL_PATCHVER:=5.10
KERNEL_TESTING_PATCHVER:=5.10
diff --git a/target/linux/ipq40xx/base-files/etc/board.d/02_network b/target/linux/ipq40xx/base-files/etc/board.d/02_network
index a38d35a10d..5072e70942 100644
--- a/target/linux/ipq40xx/base-files/etc/board.d/02_network
+++ b/target/linux/ipq40xx/base-files/etc/board.d/02_network
@@ -46,6 +46,7 @@ ipq40xx_setup_interfaces()
cilab,meshpoint-one|\
edgecore,ecw5211|\
edgecore,oap100|\
+ google,wifi|\
openmesh,a42|\
openmesh,a62)
ucidef_set_interfaces_lan_wan "eth1" "eth0"
diff --git a/target/linux/ipq40xx/base-files/lib/upgrade/platform.sh b/target/linux/ipq40xx/base-files/lib/upgrade/platform.sh
index e9c17e5b01..f02500a86c 100644
--- a/target/linux/ipq40xx/base-files/lib/upgrade/platform.sh
+++ b/target/linux/ipq40xx/base-files/lib/upgrade/platform.sh
@@ -153,6 +153,13 @@ platform_do_upgrade() {
compex,wpj419)
nand_do_upgrade "$1"
;;
+ google,wifi)
+ export_bootdevice
+ export_partdevice CI_ROOTDEV 0
+ CI_KERNPART="kernel"
+ CI_ROOTPART="rootfs"
+ emmc_do_upgrade "$1"
+ ;;
linksys,ea6350v3 |\
linksys,ea8300 |\
linksys,mr8300)
@@ -202,7 +209,8 @@ platform_do_upgrade() {
platform_copy_config() {
case "$(board_name)" in
- glinet,gl-b2200)
+ glinet,gl-b2200 |\
+ google,wifi)
emmc_copy_config
;;
esac
diff --git a/target/linux/ipq40xx/chromium/config-default b/target/linux/ipq40xx/chromium/config-default
new file mode 100644
index 0000000000..83a42dfb66
--- /dev/null
+++ b/target/linux/ipq40xx/chromium/config-default
@@ -0,0 +1,10 @@
+CONFIG_BLK_DEV_SD=y
+CONFIG_BLK_SCSI_REQUEST=y
+CONFIG_SCSI=y
+CONFIG_SG_POOL=y
+CONFIG_USB_DWC3=y
+CONFIG_USB_DWC3_HOST=y
+CONFIG_USB_DWC3_QCOM=y
+CONFIG_USB_STORAGE=y
+CONFIG_USB_XHCI_HCD=y
+CONFIG_USB_XHCI_PLATFORM=y
diff --git a/target/linux/ipq40xx/chromium/target.mk b/target/linux/ipq40xx/chromium/target.mk
new file mode 100644
index 0000000000..3983a9281a
--- /dev/null
+++ b/target/linux/ipq40xx/chromium/target.mk
@@ -0,0 +1,2 @@
+BOARDNAME:=Google Chromium
+FEATURES += emmc boot-part rootfs-part
diff --git a/target/linux/ipq40xx/files/arch/arm/boot/dts/qcom-ipq4019-wifi.dts b/target/linux/ipq40xx/files/arch/arm/boot/dts/qcom-ipq4019-wifi.dts
new file mode 100644
index 0000000000..9448e5145e
--- /dev/null
+++ b/target/linux/ipq40xx/files/arch/arm/boot/dts/qcom-ipq4019-wifi.dts
@@ -0,0 +1,413 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (c) 2016, 2018 The Linux Foundation. All rights reserved.
+ * Copyright (c) 2016 Google, Inc
+ */
+
+#include "qcom-ipq4019.dtsi"
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/leds/common.h>
+
+/ {
+ model = "Google WiFi (Gale)";
+ compatible = "google,wifi", "google,gale-v2", "qcom,ipq4019";
+
+ chosen {
+ /*
+ * rootwait: in case we're booting from slow/async USB storage.
+ */
+ bootargs-append = " rootwait";
+ stdout-path = &blsp1_uart1;
+ };
+
+ memory {
+ device_type = "memory";
+ reg = <0x80000000 0x20000000>; /* 512MB */
+ };
+
+ soc {
+ ess-switch at c000000 {
+ status = "okay";
+ };
+
+ edma at c080000 {
+ status = "okay";
+ };
+
+ ess-psgmii at 98000 {
+ status = "okay";
+ };
+ };
+};
+
+&tlmm {
+ fw_pinmux {
+ wp {
+ pins = "gpio53";
+ output-low;
+ };
+ recovery {
+ pins = "gpio57";
+ bias-none;
+ };
+ developer {
+ pins = "gpio41";
+ bias-none;
+ };
+ };
+
+ reset802_15_4 {
+ pins = "gpio60";
+ };
+
+ led_reset {
+ pins = "gpio22";
+ output-high;
+ };
+
+ sys_reset {
+ pins = "gpio19";
+ output-high;
+ };
+
+ rx_active {
+ pins = "gpio43";
+ bias-pull,down;
+ };
+
+ spi_0_pins: spi_0_pinmux {
+ pinmux {
+ function = "blsp_spi0";
+ pins = "gpio13", "gpio14","gpio15";
+ };
+ pinmux_cs {
+ function = "gpio";
+ pins = "gpio12";
+ };
+ pinconf {
+ pins = "gpio13", "gpio14","gpio15";
+ drive-strength = <12>;
+ bias-disable;
+ };
+ pinconf_cs {
+ pins = "gpio12";
+ drive-strength = <2>;
+ bias-disable;
+ output-high;
+ };
+ };
+
+ spi_1_pins: spi_1_pinmux {
+ pinmux {
+ function = "blsp_spi1";
+ pins = "gpio44", "gpio46","gpio47";
+ };
+ pinmux_cs {
+ function = "gpio";
+ pins = "gpio45";
+ };
+ pinconf {
+ pins = "gpio44", "gpio46","gpio47";
+ drive-strength = <12>;
+ bias-disable;
+ };
+ pinconf_cs {
+ pins = "gpio45";
+ drive-strength = <2>;
+ bias-disable;
+ output-high;
+ };
+ };
+
+ serial_0_pins: serial0_pinmux {
+ mux {
+ pins = "gpio16", "gpio17";
+ function = "blsp_uart0";
+ bias-disable;
+ };
+ };
+
+ serial_1_pins: serial1_pinmux {
+ mux {
+ pins = "gpio8", "gpio9", "gpio10", "gpio11";
+ function = "blsp_uart1";
+ bias-disable;
+ };
+ };
+
+ i2c_0_pins: i2c_0_pinmux {
+ mux {
+ pins = "gpio20", "gpio21";
+ function = "blsp_i2c0";
+ drive-open-drain;
+ };
+ };
+
+ i2c_1_pins: i2c_1_pinmux {
+ mux {
+ pins = "gpio34", "gpio35";
+ function = "blsp_i2c1";
+ drive-open-drain;
+ };
+ };
+
+ sd_0_pins: sd_0_pinmux {
+ sd0 {
+ pins = "gpio23", "gpio24", "gpio25", "gpio26", "gpio29", "gpio30", "gpio31", "gpio32";
+ function = "sdio";
+ drive-strength = <10>;
+ bias-pull-up;
+ pull-up-res = <0>;
+ };
+ sdclk {
+ pins = "gpio27";
+ function = "sdio";
+ drive-strength = <2>;
+ bias-pull-up;
+ pull-up-res = <0>;
+ };
+ sdcmd {
+ pins = "gpio28";
+ function = "sdio";
+ drive-strength = <10>;
+ bias-pull-up;
+ pull-up-res = <0>;
+ };
+ };
+
+ mdio_pins: mdio_pinmux {
+ mux_1 {
+ pins = "gpio6";
+ function = "mdio";
+ bias-disable;
+ };
+ mux_2 {
+ pins = "gpio7";
+ function = "mdc";
+ bias-disable;
+ };
+ mux_3 {
+ pins = "gpio40";
+ function = "gpio";
+ bias-disable;
+ output-high;
+ };
+ };
+
+ wifi1_1_pins: wifi2_pinmux {
+ mux {
+ pins = "gpio58";
+ output-low;
+ };
+ };
+};
+
+&blsp_dma {
+ status = "okay";
+};
+
+&blsp1_i2c3 {
+ pinctrl-0 = <&i2c_0_pins>;
+ pinctrl-names = "default";
+ status = "okay";
+
+ tpm at 20 {
+ compatible = "infineon,slb9645tt";
+ reg = <0x20>;
+ powered-while-suspended;
+ };
+};
+
+&blsp1_i2c4 {
+ pinctrl-0 = <&i2c_1_pins>;
+ pinctrl-names = "default";
+ status = "okay";
+
+ led-controller at 32 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "national,lp5523";
+ reg = <0x32>;
+ clock-mode = /bits/ 8 <1>;
+
+#if 1
+ led at 0 {
+ reg = <0>;
+ chan-name = "LED0_Red";
+ led-cur = /bits/ 8 <0x64>;
+ max-cur = /bits/ 8 <0x78>;
+ color = <LED_COLOR_ID_RED>;
+ };
+
+ led at 1 {
+ reg = <1>;
+ chan-name = "LED0_Green";
+ led-cur = /bits/ 8 <0x64>;
+ max-cur = /bits/ 8 <0x78>;
+ color = <LED_COLOR_ID_GREEN>;
+ };
+
+ led at 2 {
+ reg = <2>;
+ chan-name = "LED0_Blue";
+ led-cur = /bits/ 8 <0x64>;
+ max-cur = /bits/ 8 <0x78>;
+ color = <LED_COLOR_ID_BLUE>;
+ };
+#else
+ /*
+ * openwrt isn't ready to handle multi-intensity leds yet
+ * # echo 255 255 255 > /sys/class/leds/tricolor/multi_intensity
+ * # echo 255 > /sys/class/leds/tricolor/brightness
+ */
+ multi-led at 2 {
+ reg = <2>;
+ color = <LED_COLOR_ID_RGB>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ led at 0 {
+ reg = <0>;
+ chan-name = "tricolor";
+ led-cur = /bits/ 8 <0x64>;
+ max-cur = /bits/ 8 <0x78>;
+ color = <LED_COLOR_ID_RED>;
+ };
+
+ led at 1 {
+ reg = <1>;
+ chan-name = "tricolor";
+ led-cur = /bits/ 8 <0x64>;
+ max-cur = /bits/ 8 <0x78>;
+ color = <LED_COLOR_ID_GREEN>;
+ };
+
+ led at 2 {
+ reg = <2>;
+ chan-name = "tricolor";
+ led-cur = /bits/ 8 <0x64>;
+ max-cur = /bits/ 8 <0x78>;
+ color = <LED_COLOR_ID_BLUE>;
+ };
+ };
+#endif
+ };
+};
+
+&blsp1_spi1 {
+ pinctrl-0 = <&spi_0_pins>;
+ pinctrl-names = "default";
+ status = "okay";
+ cs-gpios = <&tlmm 12 GPIO_ACTIVE_HIGH>;
+
+ flash at 0 {
+ compatible = "jedec,spi-nor";
+ reg = <0>;
+ spi-max-frequency = <24000000>;
+ };
+};
+
+&blsp1_spi2 {
+ pinctrl-0 = <&spi_1_pins>;
+ pinctrl-names = "default";
+ status = "okay";
+ cs-gpios = <&tlmm 45 GPIO_ACTIVE_HIGH>;
+
+ /*
+ * This "spidev" was included in the manufacturer device tree. I
+ * suspect it's the (unused; and removed from later HW spins) Zigbee
+ * radio -- SiliconLabs EM3581 Zigbee? There's no driver or binding for
+ * this at the moment.
+ */
+ spidev at 0 {
+ compatible = "spidev";
+ reg = <0>;
+ spi-max-frequency = <24000000>;
+ };
+};
+
+&blsp1_uart1 {
+ pinctrl-0 = <&serial_0_pins>;
+ pinctrl-names = "default";
+ status = "okay";
+};
+
+&blsp1_uart2 {
+ pinctrl-0 = <&serial_1_pins>;
+ pinctrl-names = "default";
+ status = "okay";
+};
+
+&gmac0 {
+ qcom,phy_mdio_addr = <4>;
+ qcom,poll_required = <1>;
+ qcom,forced_speed = <1000>;
+ qcom,forced_duplex = <1>;
+ vlan_tag = <2 0x20>;
+};
+
+&gmac1 {
+ qcom,phy_mdio_addr = <3>;
+ qcom,forced_duplex = <1>;
+ vlan_tag = <1 0x10>;
+};
+
+&mdio {
+ status = "okay";
+ pinctrl-0 = <&mdio_pins>;
+ pinctrl-names = "default";
+};
+
+&prng {
+ status = "okay";
+};
+
+&sdhci {
+ status = "okay";
+ pinctrl-0 = <&sd_0_pins>;
+ pinctrl-names = "default";
+ clock-frequency = <192000000>;
+ vqmmc-supply = <&vqmmc>;
+ non-removable;
+};
+
+&usb2 {
+ status = "okay";
+};
+
+&usb2_hs_phy {
+ status = "okay";
+};
+
+&usb3 {
+ status = "okay";
+};
+
+&usb3_ss_phy {
+ status = "okay";
+};
+
+&usb3_hs_phy {
+ status = "okay";
+};
+
+&vqmmc {
+ status = "okay";
+};
+
+&watchdog {
+ status = "okay";
+};
+
+&wifi0 {
+ status = "okay";
+ qcom,ath10k-calibration-variant = "GO_GALE";
+};
+
+&wifi1 {
+ status = "okay";
+ pinctrl-0 = <&wifi1_1_pins>;
+ pinctrl-names = "default";
+ qcom,ath10k-calibration-variant = "GO_GALE";
+};
diff --git a/target/linux/ipq40xx/image/chromium.mk b/target/linux/ipq40xx/image/chromium.mk
index 15d4c1a077..2c8457dcfb 100644
--- a/target/linux/ipq40xx/image/chromium.mk
+++ b/target/linux/ipq40xx/image/chromium.mk
@@ -20,3 +20,17 @@ define Build/cros-vboot
-k $@ -c "root=PARTUUID=%U/PARTNROFF=1" -o $@.new
@mv $@.new $@
endef
+
+define Device/google_wifi
+ DEVICE_VENDOR := Google
+ DEVICE_MODEL := WiFi (Gale)
+ SOC := qcom-ipq4019
+ KERNEL_SUFFIX := -fit-zImage.itb.vboot
+ KERNEL = kernel-bin | fit none $$(DTS_DIR)/$$(DEVICE_DTS).dtb | cros-vboot
+ KERNEL_NAME := zImage
+ IMAGES += factory.bin
+ IMAGE/factory.bin := cros-gpt | append-kernel-part | append-rootfs
+ DEVICE_PACKAGES := ipq-wifi-google_wifi partx-utils mkf2fs e2fsprogs \
+ kmod-fs-ext4 kmod-fs-f2fs kmod-google-firmware
+endef
+TARGET_DEVICES += google_wifi
diff --git a/target/linux/ipq40xx/patches-5.10/901-arm-boot-add-dts-files.patch b/target/linux/ipq40xx/patches-5.10/901-arm-boot-add-dts-files.patch
index c51586a232..c30bc011d7 100644
--- a/target/linux/ipq40xx/patches-5.10/901-arm-boot-add-dts-files.patch
+++ b/target/linux/ipq40xx/patches-5.10/901-arm-boot-add-dts-files.patch
@@ -10,7 +10,7 @@ Signed-off-by: John Crispin <john at phrozen.org>
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
-@@ -904,11 +904,76 @@ dtb-$(CONFIG_ARCH_QCOM) += \
+@@ -904,11 +904,77 @@ dtb-$(CONFIG_ARCH_QCOM) += \
qcom-apq8074-dragonboard.dtb \
qcom-apq8084-ifc6540.dtb \
qcom-apq8084-mtp.dtb \
@@ -72,10 +72,11 @@ Signed-off-by: John Crispin <john at phrozen.org>
+ qcom-ipq4019-rtl30vw.dtb \
+ qcom-ipq4019-srr60.dtb \
+ qcom-ipq4019-srs60.dtb \
-+ qcom-ipq4019-x1pro.dtb \
+ qcom-ipq4019-u4019-32m.dtb \
++ qcom-ipq4019-wifi.dtb \
+ qcom-ipq4019-wpj419.dtb \
+ qcom-ipq4019-wtr-m2133hp.dtb \
++ qcom-ipq4019-x1pro.dtb \
+ qcom-ipq4028-wpj428.dtb \
+ qcom-ipq4029-ap-303.dtb \
+ qcom-ipq4029-ap-303h.dtb \
--
2.40.0
More information about the openwrt-devel
mailing list