howto support ramoops (former crashlog.o)
Bastian Bittorf
bb at npl.de
Wed Aug 24 09:55:55 PDT 2022
On Tue, Aug 23, 2022 at 07:53:53PM +0200, Daniel Golle wrote:
> pstore/ramoops can only work on platforms which do NOT clear DRAM
> content on (re-)boot. Many of the $vendor loaders unfortunately do that.
> Archer C6U being an MT7621-based unit will probably need a replacement
> bootloader in order to change that behavior. As it is a rather
> straight-forward board with SPI-NOR, creating a replacement loader is
> not hard (see uboot-mediatek package).
Thanks for this very convincing argument!
Attached is the full bootlog (serial console) of the device
Archer C6U v1 (including DRAM/DDR3 calibration preamble)
But what still gives me hope, are the
offset-addresses in the bootlog, e.g.:
# Booting image at bc040000
this is decimal 3.154.378.752 - and:
# Load Address: 80001000
Both addresses are way bayond the 128k RAM border - maybe
i'am just calculating the ramoops-offset in a wrong way?
Thanks a lot & bye,
bastian
-------------- next part --------------
### serial console with 57600 baud:
===================================================================
MT7621 stage1 code Aug 28 2018 16:58:15 (ASIC)
CPU=500000000 HZ BUS=166666666 HZ
==================================================================
Change MPLL source from XTAL to CR...
do MEMPLL setting..
MEMPLL Config : 0x11100000
3PLL mode + External loopback
=== XTAL-40Mhz === DDR-1200Mhz ===
PLL3 FB_DL: 0xe, 1/0 = 562/462 39000000
PLL2 FB_DL: 0x14, 1/0 = 606/418 51000000
PLL4 FB_DL: 0x18, 1/0 = 602/422 61000000
do DDR setting..[01F40000]
Apply DDR3 Setting...(use customer AC)
0 8 16 24 32 40 48 56 64 72 80 88 96 104 112 120
--------------------------------------------------------------------------------
0000:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
0001:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
0002:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
0003:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
0004:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
0005:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
0006:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
0007:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
0008:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
0009:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
000A:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
000B:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
000C:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
000D:| 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1
000E:| 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1
000F:| 0 0 1 1 1 1 1 1 1 1 1 1 0 0 0 0
0010:| 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0
0011:| 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0
0012:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
0013:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
0014:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
0015:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
0016:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
0017:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
0018:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
0019:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
001A:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
001B:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
001C:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
001D:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
001E:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
001F:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
DRAMC_DQSCTL1[0e0]=13000000
DRAMC_DQSGCTL[124]=80000033
rank 0 coarse = 15
rank 0 fine = 56
B:| 0 0 0 0 0 0 0 0 1 1 1 0 0 0 0 0
opt_dle value:9
DRAMC_DDR2CTL[07c]=C287221D
DRAMC_PADCTL4[0e4]=000022B3
DRAMC_DQIDLY1[210]=0E0F0B0F
DRAMC_DQIDLY2[214]=0C0F0D0E
DRAMC_DQIDLY3[218]=0B0B090B
DRAMC_DQIDLY4[21c]=0A0B0C09
DRAMC_R0DELDLY[018]=00001F1F
==================================================================
RX DQS perbit delay software calibration
==================================================================
1.0-15 bit dq delay value
==================================================================
bit| 0 1 2 3 4 5 6 7 8 9
--------------------------------------
0 | 14 11 15 13 13 13 14 11 11 9
10 | 11 11 9 11 11 9
--------------------------------------
==================================================================
2.dqs window
x=pass dqs delay value (min~max)center
y=0-7bit DQ of every group
input delay:DQS0 =31 DQS1 = 31
==================================================================
bit DQS0 bit DQS1
0 (1~59)30 8 (1~61)31
1 (2~61)31 9 (1~62)31
2 (1~60)30 10 (1~62)31
3 (1~60)30 11 (1~61)31
4 (1~59)30 12 (1~62)31
5 (2~60)31 13 (1~60)30
6 (1~60)30 14 (1~62)31
7 (1~59)30 15 (2~59)30
==================================================================
3.dq delay value last
==================================================================
bit| 0 1 2 3 4 5 6 7 8 9
--------------------------------------
0 | 15 11 15 14 14 13 15 12 11 9
10 | 11 11 9 12 11 10
==================================================================
==================================================================
TX perbyte calibration
==================================================================
DQS loop = 15, cmp_err_1 = ffff0000
dqs_perbyte_dly.last_dqsdly_pass[0]=15, finish count=1
dqs_perbyte_dly.last_dqsdly_pass[1]=15, finish count=2
DQ loop=15, cmp_err_1 = ffff0000
dqs_perbyte_dly.last_dqdly_pass[0]=15, finish count=1
dqs_perbyte_dly.last_dqdly_pass[1]=15, finish count=2
byte:0, (DQS,DQ)=(8,8)
byte:1, (DQS,DQ)=(8,8)
DRAMC_DQODLY1[200]=88888888
DRAMC_DQODLY2[204]=88888888
20,data:88
[EMI] DRAMC calibration passed
===================================================================
MT7621 stage1 code done
CPU=500000000 HZ BUS=166666666 HZ
===================================================================
### serial console with 115200 baud:
U-Boot 1.1.3 (Feb 24 2020 - 11:29:39)
Board: Ralink APSoC DRAM: 128 MB
relocate_code Poiner at: 87f58000
Config XHCI 40M PLL
******************************
Software System Reset Occurred
******************************
flash manufacture id: ef, device id 40 18
find flash: W25Q128BV
*** Warning - bad CRC, using default environment
============================================
Ralink UBoot Version: 5.0.0.0
--------------------------------------------
ASIC MT7621A DualCore (MAC to MT7530 Mode)
DRAM_CONF_FROM: Auto-Detection
DRAM_TYPE: DDR3
DRAM bus: 16 bit
Xtal Mode=3 OCP Ratio=1/3
Flash component: SPI Flash
Date:Feb 24 2020 Time:11:29:39
============================================
THIS IS uboot
icache: sets:256, ways:4, linesz:32 ,total:32768
dcache: sets:256, ways:4, linesz:32 ,total:32768
##### The CPU freq = 880 MHZ ####
estimate memory size =128 Mbytes
Press '4' or 't' to break the booting process
Press 'x' to enter recovery web server 0
nm_init:791
nm_initFwupPtnStruct:276
nm_lib_readPtnTable:738
[NM_Debug](nm_lib_readPtnTable) 00743: NM_PTN_TABLE_BASE = 0xfe0000
[NM_Debug](nm_lib_readPtnFromNvram) 00569: partition_used_len = 920, requried len = 8192
[NM_Debug](nm_lib_readPtnTable) 00751: Reading Partition Table from NVRAM ... OK
[NM_Debug](nm_lib_readPtnTable) 00759: Parsing Partition Table ... OK
[NM_Debug](nm_lib_readPtnFromNvram) 00569: partition_used_len = 2, requried len = 2
factory boot check integer ok.
3: System Boot system code via Flash.
## Booting image at bc040000 ...
Image Name: MIPS OpenWrt Linux-5.10.137
Image Type: MIPS Linux Kernel Image (lzma compressed)
Data Size: 2609199 Bytes = 2.5 MB
Load Address: 80001000
Entry Point: 80001000
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK
No initrd
## Transferring control to Linux (at address 80001000) ...
## Giving linux memsize in MB, 128
Starting kernel ...
[ 0.000000] Linux version 5.10.137 (bastian at ryzen) (mipsel-openwrt-linux-musl-gcc (OpenWrt GCC 11.3.0 r20179+31-57cad53f4e) 11.3.0, GNU ld (GNU Binutils) 2.37) #0 SMP Wed Aug 24 15:42:49 2022
[ 0.000000] SoC Type: MediaTek MT7621 ver:1 eco:3
[ 0.000000] printk: bootconsole [early0] enabled
[ 0.000000] CPU0 revision is: 0001992f (MIPS 1004Kc)
[ 0.000000] MIPS: machine is TP-Link Archer C6U v1
[ 0.000000] OF: fdt: Reserved memory: unsupported node format, ignoring
[ 0.000000] Initrd not found or empty - disabling initrd
[ 0.000000] VPE topology {2,2} total 4
[ 0.000000] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
[ 0.000000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
[ 0.000000] MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
[ 0.000000] Zone ranges:
[ 0.000000] Normal [mem 0x0000000000000000-0x0000000007ffffff]
[ 0.000000] HighMem empty
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x0000000000000000-0x0000000007ffffff]
[ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000007ffffff]
[ 0.000000] percpu: Embedded 15 pages/cpu s30224 r8192 d23024 u61440
[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 32480
[ 0.000000] Kernel command line: console=ttyS0,115200 rootfstype=squashfs,jffs2 oops=panic panic=10
[ 0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes, linear)
[ 0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes, linear)
[ 0.000000] Writing ErrCtl register=000032b0
[ 0.000000] Readback ErrCtl register=000032b0
[ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
[ 0.000000] Memory: 119796K/131072K available (6397K kernel code, 624K rwdata, 1148K rodata, 1288K init, 235K bss, 11276K reserved, 0K cma-reserved, 0K highmem)
[ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
[ 0.000000] rcu: Hierarchical RCU implementation.
[ 0.000000] Tracing variant of Tasks RCU enabled.
[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies.
[ 0.000000] NR_IRQS: 256
[ 0.000000] CPU Clock: 880MHz
[ 0.000000] clocksource: GIC: mask: 0xffffffffffffffff max_cycles: 0xcaf478abb4, max_idle_ns: 440795247997
ns
[ 0.000012] sched_clock: 64 bits at 880MHz, resolution 1ns, wraps every 4398046511103ns
[ 0.007944] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 4343773742 ns
[ 0.016996] Calibrating delay loop... 586.13 BogoMIPS (lpj=2930688)
[ 0.083165] pid_max: default: 32768 minimum: 301
[ 0.087927] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
[ 0.095129] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
[ 0.105707] rcu: Hierarchical SRCU implementation.
[ 0.110743] dyndbg: Ignore empty _ddebug table in a CONFIG_DYNAMIC_DEBUG_CORE build
[ 0.118838] smp: Bringing up secondary CPUs ...
[ 0.124102] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
[ 0.124113] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
[ 0.124125] MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
[ 0.124201] CPU1 revision is: 0001992f (MIPS 1004Kc)
[ 0.178649] Synchronize counters for CPU 1: done.
[ 0.211038] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
[ 0.211048] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
[ 0.211055] MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
[ 0.211107] CPU2 revision is: 0001992f (MIPS 1004Kc)
[ 0.270038] Synchronize counters for CPU 2: done.
[ 0.300617] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
[ 0.300626] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
[ 0.300633] MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
[ 0.300686] CPU3 revision is: 0001992f (MIPS 1004Kc)
[ 0.355226] Synchronize counters for CPU 3: done.
[ 0.385088] smp: Brought up 1 node, 4 CPUs
[ 0.393415] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000
ns
[ 0.403239] futex hash table entries: 1024 (order: 3, 32768 bytes, linear)
[ 0.410248] pinctrl core: initialized pinctrl subsystem
[ 0.417752] NET: Registered protocol family 16
[ 0.424582] cpuidle: using governor teo
[ 0.475389] clocksource: Switched to clocksource GIC
[ 0.482156] NET: Registered protocol family 2
[ 0.486825] IP idents hash table entries: 2048 (order: 2, 16384 bytes, linear)
[ 0.494726] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes, linear)
[ 0.503119] TCP established hash table entries: 1024 (order: 0, 4096 bytes, linear)
[ 0.510712] TCP bind hash table entries: 1024 (order: 1, 8192 bytes, linear)
[ 0.517742] TCP: Hash tables configured (established 1024 bind 1024)
[ 0.524156] UDP hash table entries: 256 (order: 1, 8192 bytes, linear)
[ 0.530650] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes, linear)
[ 0.537832] NET: Registered protocol family 1
[ 0.542123] PCI: CLS 0 bytes, default 32
[ 0.548590] workingset: timestamp_bits=14 max_order=15 bucket_order=1
[ 0.559068] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.564813] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 0.577441] mt7621_gpio 1e000600.gpio: registering 32 gpios
[ 0.583287] mt7621_gpio 1e000600.gpio: registering 32 gpios
[ 0.589314] mt7621_gpio 1e000600.gpio: registering 32 gpios
[ 0.595907] Serial: 8250/16550 driver, 3 ports, IRQ sharing disabled
[ 0.603810] printk: console [ttyS0] disabled
[ 0.608187] 1e000c00.uartlite: ttyS0 at MMIO 0x1e000c00 (irq = 19, base_baud = 3125000) is a 16550A
[ 0.617187] printk: console [ttyS0] enabled
[ 0.617187] printk: console [ttyS0] enabled
[ 0.625445] printk: bootconsole [early0] disabled
[ 0.625445] printk: bootconsole [early0] disabled
[ 0.637666] spi-mt7621 1e000b00.spi: sys_freq: 220000000
[ 0.644687] spi-nor spi0.0: w25q128 (16384 Kbytes)
[ 0.649730] 5 fixed-partitions partitions found on MTD device spi0.0
[ 0.656135] OF: Bad cell count for /palmbus at 1e000000/spi at b00/flash at 0/partitions
[ 0.663436] OF: Bad cell count for /palmbus at 1e000000/spi at b00/flash at 0/partitions
[ 0.671500] OF: Bad cell count for /palmbus at 1e000000/spi at b00/flash at 0/partitions
[ 0.678854] OF: Bad cell count for /palmbus at 1e000000/spi at b00/flash at 0/partitions
[ 0.687307] Creating 5 MTD partitions on "spi0.0":
[ 0.692112] 0x000000000000-0x000000040000 : "u-boot"
[ 0.698301] 0x000000040000-0x000000fa0000 : "firmware"
[ 0.704645] 2 uimage-fw partitions found on MTD device firmware
[ 0.710654] Creating 2 MTD partitions on "firmware":
[ 0.715723] 0x000000000000-0x00000027d06f : "kernel"
[ 0.720665] mtd: partition "kernel" doesn't end on an erase/write block -- force read-only
[ 0.729922] 0x00000027d06f-0x000000f60000 : "rootfs"
[ 0.734888] mtd: partition "rootfs" doesn't start on an erase/write block boundary -- force read-only
[ 0.744827] mtd: device 3 (rootfs) set to be root filesystem
[ 0.750642] 1 squashfs-split partitions found on MTD device rootfs
[ 0.756845] 0x0000008b0000-0x000000f60000 : "rootfs_data"
[ 0.763153] 0x000000fa0000-0x000000fb0000 : "config"
[ 0.769120] 0x000000fb0000-0x000000ff0000 : "tplink"
[ 0.774960] 0x000000ff0000-0x000001000000 : "radio"
[ 0.826606] mt7530 mdio-bus:1f: MT7530 adapts as multi-chip module
[ 0.837268] mtk_soc_eth 1e100000.ethernet eth0: mediatek frame engine at 0xbe100000, irq 21
[ 0.846558] mtk_soc_eth 1e100000.ethernet wan: mediatek frame engine at 0xbe100000, irq 21
[ 0.856282] i2c /dev entries driver
[ 0.861977] mt7621-pci 1e140000.pcie: host bridge /pcie at 1e140000 ranges:
[ 0.868750] mt7621-pci 1e140000.pcie: No bus range found for /pcie at 1e140000, using [bus 00-ff]
[ 0.877576] mt7621-pci 1e140000.pcie: MEM 0x0060000000..0x006fffffff -> 0x0000000000
[ 0.885755] mt7621-pci 1e140000.pcie: IO 0x001e160000..0x001e16ffff -> 0x0000000000
[ 0.893992] mt7621-pci 1e140000.pcie: Parsing DT failed
[ 0.901178] NET: Registered protocol family 10
[ 0.907504] Segment Routing with IPv6
[ 0.911255] NET: Registered protocol family 17
[ 0.916264] 8021q: 802.1Q VLAN Support v1.8
[ 0.924397] mt7530 mdio-bus:1f: MT7530 adapts as multi-chip module
[ 0.948996] mt7530 mdio-bus:1f lan1 (uninitialized): PHY [mt7530-0:01] driver [MediaTek MT7530 PHY] (irq=26)
[ 0.961378] mt7530 mdio-bus:1f lan2 (uninitialized): PHY [mt7530-0:02] driver [MediaTek MT7530 PHY] (irq=27)
[ 0.973748] mt7530 mdio-bus:1f lan3 (uninitialized): PHY [mt7530-0:03] driver [MediaTek MT7530 PHY] (irq=28)
[ 0.986141] mt7530 mdio-bus:1f lan4 (uninitialized): PHY [mt7530-0:04] driver [MediaTek MT7530 PHY] (irq=29)
[ 0.998774] mt7530 mdio-bus:1f: configuring for fixed/rgmii link mode
[ 1.009257] DSA: tree 0 setup
[ 1.012598] rt2880-pinmux pinctrl: pcie is already enabled
[ 1.018181] mt7621-pci 1e140000.pcie: host bridge /pcie at 1e140000 ranges:
[ 1.024869] mt7621-pci 1e140000.pcie: No bus range found for /pcie at 1e140000, using [bus 00-ff]
[ 1.033662] mt7621-pci 1e140000.pcie: MEM 0x0060000000..0x006fffffff -> 0x0000000000
[ 1.041838] mt7621-pci 1e140000.pcie: IO 0x001e160000..0x001e16ffff -> 0x0000000000
[ 1.050110] mt7621-pci-phy 1e149000.pcie-phy: PHY for 0xbe149000 (dual port = 1)
[ 1.057914] mt7621-pci-phy 1e14a000.pcie-phy: PHY for 0xbe14a000 (dual port = 0)
[ 1.065666] mt7621-pci 1e140000.pcie: failed to parse bus ranges property: -22
[ 1.173122] mt7621-pci-phy 1e149000.pcie-phy: Xtal is 40MHz
[ 1.178717] mt7621-pci-phy 1e14a000.pcie-phy: Xtal is 40MHz
[ 1.284480] mt7621-pci 1e140000.pcie: pcie2 no card, disable it (RST & CLK)
[ 1.291432] mt7621-pci 1e140000.pcie: PCIE0 enabled
[ 1.296309] mt7621-pci 1e140000.pcie: PCIE1 enabled
[ 1.301170] mt7621-pci 1e140000.pcie: PCI coherence region base: 0x60000000, mask/settings: 0xf0000002
[ 1.310631] mt7621-pci 1e140000.pcie: PCI host bridge to bus 0000:00
[ 1.317011] pci_bus 0000:00: root bus resource [io 0x1e160000-0x1e16ffff]
[ 1.323861] pci_bus 0000:00: root bus resource [mem 0x60000000-0x6fffffff]
[ 1.330727] pci_bus 0000:00: root bus resource [bus 00-ff]
[ 1.336224] pci_bus 0000:00: root bus resource [mem 0x60000000-0x6fffffff] (bus address [0x00000000-0x0fffffff])
[ 1.346420] pci 0000:00:00.0: [0e8d:0801] type 01 class 0x060400
[ 1.352417] pci 0000:00:00.0: reg 0x10: [mem 0x00000000-0x7fffffff]
[ 1.358682] pci 0000:00:00.0: reg 0x14: [mem 0x60500000-0x6050ffff]
[ 1.364998] pci 0000:00:00.0: supports D1
[ 1.369011] pci 0000:00:00.0: PME# supported from D0 D1 D3hot
[ 1.375521] pci 0000:00:01.0: [0e8d:0801] type 01 class 0x060400
[ 1.381554] pci 0000:00:01.0: reg 0x10: [mem 0x00000000-0x7fffffff]
[ 1.387821] pci 0000:00:01.0: reg 0x14: [mem 0x60510000-0x6051ffff]
[ 1.394124] pci 0000:00:01.0: supports D1
[ 1.398135] pci 0000:00:01.0: PME# supported from D0 D1 D3hot
[ 1.405897] pci 0000:01:00.0: [14c3:7603] type 00 class 0x028000
[ 1.411948] pci 0000:01:00.0: reg 0x10: initial BAR value 0x00000000 invalid
[ 1.419001] pci 0000:01:00.0: reg 0x10: [mem size 0x00100000]
[ 1.424864] pci 0000:01:00.0: PME# supported from D0 D3hot D3cold
[ 1.432669] pci 0000:00:00.0: PCI bridge to [bus 01-ff]
[ 1.437928] pci 0000:00:00.0: bridge window [io 0x0000-0x0fff]
[ 1.443998] pci 0000:00:00.0: bridge window [mem 0x60000000-0x600fffff]
[ 1.450774] pci 0000:00:00.0: bridge window [mem 0x60100000-0x601fffff pref]
[ 1.458000] pci_bus 0000:01: busn_res: [bus 01-ff] end is updated to 01
[ 1.464867] pci 0000:02:00.0: [14c3:7663] type 00 class 0x000280
[ 1.470926] pci 0000:02:00.0: reg 0x10: initial BAR value 0x00000000 invalid
[ 1.477976] pci 0000:02:00.0: reg 0x10: [mem size 0x00100000 64bit pref]
[ 1.484664] pci 0000:02:00.0: reg 0x18: initial BAR value 0x00000000 invalid
[ 1.491724] pci 0000:02:00.0: reg 0x18: [mem size 0x00004000 64bit pref]
[ 1.498433] pci 0000:02:00.0: reg 0x20: initial BAR value 0x00000000 invalid
[ 1.505468] pci 0000:02:00.0: reg 0x20: [mem size 0x00001000 64bit pref]
[ 1.512261] pci 0000:02:00.0: supports D1 D2
[ 1.516531] pci 0000:02:00.0: PME# supported from D0 D1 D2 D3hot D3cold
[ 1.523159] pci 0000:02:00.0: 2.000 Gb/s available PCIe bandwidth, limited by 2.5 GT/s PCIe x1 link at 0000:00:01.0 (capable of 4.000 Gb/s with 5.0 GT/s PCIe x1 link)
[ 1.539661] pci 0000:00:01.0: PCI bridge to [bus 02-ff]
[ 1.544889] pci 0000:00:01.0: bridge window [io 0x0000-0x0fff]
[ 1.550989] pci 0000:00:01.0: bridge window [mem 0x60200000-0x602fffff]
[ 1.557773] pci 0000:00:01.0: bridge window [mem 0x60300000-0x604fffff pref]
[ 1.564970] pci_bus 0000:02: busn_res: [bus 02-ff] end is updated to 02
[ 1.571631] pci 0000:00:00.0: BAR 0: no space for [mem size 0x80000000]
[ 1.578246] pci 0000:00:00.0: BAR 0: failed to assign [mem size 0x80000000]
[ 1.585182] pci 0000:00:01.0: BAR 0: no space for [mem size 0x80000000]
[ 1.591782] pci 0000:00:01.0: BAR 0: failed to assign [mem size 0x80000000]
[ 1.598738] pci 0000:00:00.0: BAR 8: assigned [mem 0x60000000-0x600fffff]
[ 1.605525] pci 0000:00:00.0: BAR 9: assigned [mem 0x60100000-0x601fffff pref]
[ 1.612715] pci 0000:00:01.0: BAR 8: assigned [mem 0x60200000-0x602fffff]
[ 1.619497] pci 0000:00:01.0: BAR 9: assigned [mem 0x60300000-0x604fffff pref]
[ 1.626710] pci 0000:00:00.0: BAR 1: assigned [mem 0x60500000-0x6050ffff]
[ 1.633473] pci 0000:00:01.0: BAR 1: assigned [mem 0x60510000-0x6051ffff]
[ 1.640256] pci 0000:00:00.0: BAR 7: assigned [io 0x1e160000-0x1e160fff]
[ 1.647036] pci 0000:00:01.0: BAR 7: assigned [io 0x1e161000-0x1e161fff]
[ 1.653807] pci 0000:01:00.0: BAR 0: assigned [mem 0x60000000-0x600fffff]
[ 1.660589] pci 0000:00:00.0: PCI bridge to [bus 01]
[ 1.665558] pci 0000:00:00.0: bridge window [io 0x1e160000-0x1e160fff]
[ 1.672318] pci 0000:00:00.0: bridge window [mem 0x60000000-0x600fffff]
[ 1.679096] pci 0000:00:00.0: bridge window [mem 0x60100000-0x601fffff pref]
[ 1.686318] pci 0000:02:00.0: BAR 0: assigned [mem 0x60300000-0x603fffff 64bit pref]
[ 1.694039] pci 0000:02:00.0: BAR 2: assigned [mem 0x60400000-0x60403fff 64bit pref]
[ 1.701790] pci 0000:02:00.0: BAR 4: assigned [mem 0x60404000-0x60404fff 64bit pref]
[ 1.709529] pci 0000:00:01.0: PCI bridge to [bus 02]
[ 1.714472] pci 0000:00:01.0: bridge window [io 0x1e161000-0x1e161fff]
[ 1.721251] pci 0000:00:01.0: bridge window [mem 0x60200000-0x602fffff]
[ 1.728034] pci 0000:00:01.0: bridge window [mem 0x60300000-0x604fffff pref]
[ 1.736981] mt7530 mdio-bus:1f: Link is Up - 1Gbps/Full - flow control rx/tx
[ 1.749109] VFS: Mounted root (squashfs filesystem) readonly on device 31:3.
[ 1.760556] Freeing unused kernel memory: 1288K
[ 1.765085] This architecture does not have kernel memory protection.
[ 1.771570] Run /sbin/init as init process
[ 2.161951] init: Console is alive
[ 2.165838] init: - watchdog -
[ 3.274301] kmodloader: loading kernel modules from /etc/modules-boot.d/*
[ 3.315206] usbcore: registered new interface driver usbfs
[ 3.320944] usbcore: registered new interface driver hub
[ 3.326457] usbcore: registered new device driver usb
[ 3.435574] SCSI subsystem initialized
[ 3.450639] xhci-mtk 1e1c0000.xhci: supply vusb33 not found, using dummy regulator
[ 3.458654] xhci-mtk 1e1c0000.xhci: xHCI Host Controller
[ 3.464008] xhci-mtk 1e1c0000.xhci: new USB bus registered, assigned bus number 1
[ 3.485613] xhci-mtk 1e1c0000.xhci: hcc params 0x01401198 hci version 0x96 quirks 0x0000000000290010
[ 3.494791] xhci-mtk 1e1c0000.xhci: irq 20, io mem 0x1e1c0000
[ 3.501819] hub 1-0:1.0: USB hub found
[ 3.505750] hub 1-0:1.0: 2 ports detected
[ 3.510390] xhci-mtk 1e1c0000.xhci: xHCI Host Controller
[ 3.515776] xhci-mtk 1e1c0000.xhci: new USB bus registered, assigned bus number 2
[ 3.523260] xhci-mtk 1e1c0000.xhci: Host supports USB 3.0 SuperSpeed
[ 3.529828] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM.
[ 3.538830] hub 2-0:1.0: USB hub found
[ 3.542741] hub 2-0:1.0: 1 port detected
[ 3.558426] usbcore: registered new interface driver usb-storage
[ 3.565109] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
[ 3.585756] init: - preinit -
[ 4.121064] random: jshn: uninitialized urandom read (4 bytes read)
[ 4.200831] random: jshn: uninitialized urandom read (4 bytes read)
[ 4.249632] random: jshn: uninitialized urandom read (4 bytes read)
[ 4.639626] mtk_soc_eth 1e100000.ethernet eth0: configuring for fixed/rgmii link mode
[ 4.647945] mtk_soc_eth 1e100000.ethernet eth0: Link is Up - 1Gbps/Full - flow control rx/tx
[ 4.655901] mt7530 mdio-bus:1f lan1: configuring for phy/gmii link mode
[ 4.663270] 8021q: adding VLAN 0 to HW filter on device lan1
[ 4.671997] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
Press the [f] key and hit [enter] to enter failsafe mode
Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level
[ 6.845195] mount_root: loading kmods from internal overlay
[ 6.889493] kmodloader: loading kernel modules from //etc/modules-boot.d/*
[ 6.903495] kmodloader: done loading kernel modules from //etc/modules-boot.d/*
[ 7.121211] jffs2: notice: (602) jffs2_build_xattr_subsystem: complete building xattr subsystem, 30 of xdatum (28 unchecked, 2 orphan) and 40 of xref (2 dead, 0 orphan) found.
[ 7.137895] block: attempting to load /tmp/jffs_cfg/upper/etc/config/fstab
[ 7.152480] block: extroot: not configured
[ 7.188275] jffs2: notice: (600) jffs2_build_xattr_subsystem: complete building xattr subsystem, 30 of xdatum (28 unchecked, 2 orphan) and 40 of xref (2 dead, 0 orphan) found.
[ 7.206277] mount_root: loading kmods from internal overlay
[ 7.243451] kmodloader: loading kernel modules from /tmp/overlay/upper/etc/modules-boot.d/*
[ 7.255831] kmodloader: done loading kernel modules from /tmp/overlay/upper/etc/modules-boot.d/*
[ 7.379914] block: attempting to load /tmp/jffs_cfg/upper/etc/config/fstab
[ 7.390085] block: extroot: not configured
[ 7.395579] mount_root: switching to jffs2 overlay
[ 7.422799] overlayfs: upper fs does not support tmpfile.
[ 7.436618] urandom-seed: Seeding with /etc/urandom.seed
[ 7.503213] procd: - early -
[ 7.506421] procd: - watchdog -
[ 7.525698] random: crng init done
[ 7.529156] random: 7 urandom warning(s) missed due to ratelimiting
[ 8.095720] procd: - watchdog -
[ 8.106338] procd: - ubus -
[ 8.173128] procd: - init -
Please press Enter to activate this console.
[ 8.411781] zram: Added device: zram0
[ 8.419012] zram0: detected capacity change from 0 to 4194304
[ 8.495489] Adding 4092k swap on /dev/zram0. Priority:-2 extents:1 across:4092k SS
[ 12.848464] urngd: v1.0.2 started.
[ 20.819388] kmodloader: loading kernel modules from /etc/modules.d/*
[ 21.048193] GACT probability on
[ 21.052917] Mirror/redirect action on
[ 21.068822] u32 classifier
[ 21.071546] input device check on
[ 21.075184] Actions configured
[ 21.092203] Simple TC action Loaded
[ 21.119488] Loading modules backported from Linux version v5.15.58-0-g7d8048d4e064
[ 21.127115] Backport generated by backports.git v5.15.58-1-0-g42a95ce7
[ 21.161103] usbcore: registered new interface driver ums-alauda
[ 21.168895] usbcore: registered new interface driver ums-cypress
[ 21.176870] usbcore: registered new interface driver ums-datafab
[ 21.184609] usbcore: registered new interface driver ums-freecom
[ 21.192680] usbcore: registered new interface driver ums-isd200
[ 21.200601] usbcore: registered new interface driver ums-jumpshot
[ 21.208559] usbcore: registered new interface driver ums-karma
[ 21.216646] usbcore: registered new interface driver ums-sddr09
[ 21.224403] usbcore: registered new interface driver ums-sddr55
[ 21.232389] usbcore: registered new interface driver ums-usbat
[ 21.260599] xt_time: kernel timezone is -0000
[ 21.479606] mt7621-pci 1e140000.pcie: bus=1 slot=0 irq=22
[ 21.485069] pci 0000:00:00.0: enabling device (0006 -> 0007)
[ 21.490747] mt7603e 0000:01:00.0: enabling device (0000 -> 0002)
[ 21.496926] mt7603e 0000:01:00.0: ASIC revision: 76030010
[ 22.553204] mt7603e 0000:01:00.0: Firmware Version: ap_pcie
[ 22.558833] mt7603e 0000:01:00.0: Build Time: 20160107100755
[ 22.585379] mt7603e 0000:01:00.0: firmware init done
[ 22.835718] PPP generic driver version 2.4.2
[ 22.842440] NET: Registered protocol family 24
[ 22.875466] kmodloader: done loading kernel modules from /etc/modules.d/*
[ 29.365482] mtk_soc_eth 1e100000.ethernet eth0: Link is Down
[ 29.384300] mtk_soc_eth 1e100000.ethernet eth0: configuring for fixed/rgmii link mode
[ 29.392629] mtk_soc_eth 1e100000.ethernet eth0: Link is Up - 1Gbps/Full - flow control rx/tx
[ 29.395998] mt7530 mdio-bus:1f lan1: configuring for phy/gmii link mode
[ 29.409020] 8021q: adding VLAN 0 to HW filter on device lan1
[ 29.417736] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 29.426262] br-lan: port 1(lan1) entered blocking state
[ 29.431547] br-lan: port 1(lan1) entered disabled state
[ 29.438587] device lan1 entered promiscuous mode
[ 29.443253] device eth0 entered promiscuous mode
[ 29.481614] mt7530 mdio-bus:1f lan2: configuring for phy/gmii link mode
[ 29.489023] 8021q: adding VLAN 0 to HW filter on device lan2
[ 29.498331] br-lan: port 2(lan2) entered blocking state
[ 29.503635] br-lan: port 2(lan2) entered disabled state
[ 29.510319] device lan2 entered promiscuous mode
[ 29.531866] mt7530 mdio-bus:1f lan3: configuring for phy/gmii link mode
[ 29.539150] 8021q: adding VLAN 0 to HW filter on device lan3
[ 29.549766] br-lan: port 3(lan3) entered blocking state
[ 29.555071] br-lan: port 3(lan3) entered disabled state
[ 29.562045] device lan3 entered promiscuous mode
[ 29.579273] mt7530 mdio-bus:1f lan4: configuring for phy/gmii link mode
[ 29.586606] 8021q: adding VLAN 0 to HW filter on device lan4
[ 29.595859] br-lan: port 4(lan4) entered blocking state
[ 29.601140] br-lan: port 4(lan4) entered disabled state
[ 29.608240] device lan4 entered promiscuous mode
[ 29.640154] mtk_soc_eth 1e100000.ethernet wan: PHY [mdio-bus:00] driver [Generic PHY] (irq=POLL)
[ 29.649029] mtk_soc_eth 1e100000.ethernet wan: configuring for phy/rgmii-rxid link mode
[ 32.385813] mt7530 mdio-bus:1f lan1: Link is Up - 1Gbps/Full - flow control rx/tx
[ 32.393452] br-lan: port 1(lan1) entered blocking state
[ 32.399208] br-lan: port 1(lan1) entered forwarding state
[ 32.407764] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
[ 32.523368] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0-1: link becomes ready archer-C6U-v1-routerwand
[ 33.735566] NET: Unregistered protocol family 24
[ 33.839966] wlan0: Created IBSS using preconfigured BSSID 02:ca:ff:ee:ba:be
[ 33.847112] wlan0: Creating new IBSS network, BSSID 02:ca:ff:ee:ba:be
[ 33.864188] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[ 33.978373] device wlan0-1 entered promiscuous mode
[ 33.984551] br-mastergate: port 1(roaming1) entered blocking state
[ 33.991101] br-mastergate: port 1(roaming1) entered disabled state
[ 33.998240] device roaming1 entered promiscuous mode
[ 34.010134] br-mastergate: port 1(roaming1) entered blocking state
[ 34.016393] br-mastergate: port 1(roaming1) entered forwarding state
More information about the openwrt-devel
mailing list