[PATCH v8 2/2] mvebu: add support for iEi Puzzle-M901/Puzzle-M902
Josef Schlehofer
josef.schlehofer at nic.cz
Thu Sep 2 02:52:20 PDT 2021
Hi,
Do you have any plans to upstream your DTS files for Puzzle M901 and
Puzzle M902 into kernel?
Regards,
Josef
On 02. 09. 21 11:47, eveans2002 at gmail.com wrote:
> From: Ian Chang <ianchang at ieiworld.com>
>
> Hardware specification
> ----------------------
> * CN9130 SoC, Quad-core ARMv8 Cortex-72 @ 2200 MHz
> * 4 GB DDR
> * 4 GB eMMC
> * mmcblk0
> - mmcblk0p1 64M kernel_1
> - mmcblk0p2 64M kernel_2
> - mmcblk0p3 512M rootfs_1
> - mmcblk0p4 512M rootfs_2
> - mmcblk0p5 512M Reserved
> - mmcblk0p6 64M Reserved
> - mmcblk0p7 1.8G rootfs_data
>
> * 4 MB (SPI Flash)
> * 6 x 2.5 Gigabit ports (Puzzle-M901)
> - External PHY with 6 ports (AQR112R)
>
> * 6 x 2.5 Gigabit ports (Puzzle-M902)
> - External PHY with 6 ports (AQR112R)
> 3 x 10 Gigabit ports (Puzzle-M902)
> - External PHY with 3 ports (AQR113R)
>
> * 4 x Front panel LED
> * 1 x USB 3.0
> * Reset button on Rear panel
> * UART (115200 8N1,header on PCB)
>
> Flash instructions:
> The original firmware is based on OpenWrt.
> Flash firmware using LuCI and CLI
>
> Signed-off-by: Ian Chang <ianchang at ieiworld.com>
> ---
> .../base-files/etc/board.d/02_network | 6 +
> .../base-files/lib/upgrade/emmc-puzzle.sh | 36 ++
> .../base-files/lib/upgrade/platform.sh | 8 +
> .../boot/dts/marvell/cn9131-puzzle-m901.dts | 319 ++++++++++++
> .../boot/dts/marvell/cn9132-puzzle-m902.dts | 481 ++++++++++++++++++
> target/linux/mvebu/image/cortexa72.mk | 18 +
> 6 files changed, 868 insertions(+)
> mode change 100644 => 100755 target/linux/mvebu/cortexa72/base-files/etc/board.d/02_network
> create mode 100755 target/linux/mvebu/cortexa72/base-files/lib/upgrade/emmc-puzzle.sh
> create mode 100644 target/linux/mvebu/files/arch/arm64/boot/dts/marvell/cn9131-puzzle-m901.dts
> create mode 100644 target/linux/mvebu/files/arch/arm64/boot/dts/marvell/cn9132-puzzle-m902.dts
>
> diff --git a/target/linux/mvebu/cortexa72/base-files/etc/board.d/02_network b/target/linux/mvebu/cortexa72/base-files/etc/board.d/02_network
> old mode 100644
> new mode 100755
> index dbffd00223..f185a88347
> --- a/target/linux/mvebu/cortexa72/base-files/etc/board.d/02_network
> +++ b/target/linux/mvebu/cortexa72/base-files/etc/board.d/02_network
> @@ -10,6 +10,12 @@ board_config_update
> board=$(board_name)
>
> case "$board" in
> +iei,puzzle-m901)
> + ucidef_set_interfaces_lan_wan "eth1 eth2 eth3 eth4 eth5" "eth0"
> + ;;
> +iei,puzzle-m902)
> + ucidef_set_interfaces_lan_wan "eth1 eth2 eth3 eth4 eth5 eth10 eth11 eth12" "eth0"
> + ;;
> marvell,armada8040-mcbin-doubleshot|\
> marvell,armada8040-mcbin-singleshot)
> ucidef_set_interfaces_lan_wan "eth0 eth1 eth3" "eth2"
> diff --git a/target/linux/mvebu/cortexa72/base-files/lib/upgrade/emmc-puzzle.sh b/target/linux/mvebu/cortexa72/base-files/lib/upgrade/emmc-puzzle.sh
> new file mode 100755
> index 0000000000..5e5c356ed6
> --- /dev/null
> +++ b/target/linux/mvebu/cortexa72/base-files/lib/upgrade/emmc-puzzle.sh
> @@ -0,0 +1,36 @@
> +platform_do_upgrade_emmc() {
> + local board=$(board_name)
> + local diskdev partdev
> +
> + export_bootdevice && export_partdevice diskdev 0 || {
> + v "Unable to determine upgrade device"
> + return 1
> + }
> + sync
> + if [ "$UPGRADE_OPT_SAVE_PARTITIONS" = "1" ]; then
> + get_partitions "/dev/$diskdev" bootdisk
> + v "Extract boot sector from the image"
> + get_image_dd "$1" of=/tmp/image.bs count=1 bs=512b
> + get_partitions /tmp/image.bs image
> + fi
> +
> + #iterate over each partition from the image and write it to the boot disk
> + while read part start size; do
> + if export_partdevice partdev $part; then
> + if [ "$partdev" = "mmcblk0p2" ]; then
> + v "Writing image mmcblk0p3 for /dev/$partdev $start $size"
> + get_image_dd "$1" of="/dev/mmcblk0p3" ibs="512" obs=1M skip="$start" count="$size" conv=fsync
> + elif [ "$partdev" = "mmcblk0p1" ]; then
> + v "Writing image mmcblk0p1 for /dev/$partdev $start $size"
> + get_image_dd "$1" of="/dev/$partdev" ibs="512" obs=1M skip="$start" count="$size" conv=fsync
> + fi
> + else
> + v "Unable to find partition $part device, skipped."
> + fi
> + done < /tmp/partmap.image
> +
> + v "Writing new UUID to /dev/$diskdev..."
> + get_image_dd "$1" of="/dev/$diskdev" bs=1 skip=440 count=4 seek=440 conv=fsync
> +
> + sleep 1
> +}
> diff --git a/target/linux/mvebu/cortexa72/base-files/lib/upgrade/platform.sh b/target/linux/mvebu/cortexa72/base-files/lib/upgrade/platform.sh
> index 74aad434ea..ef09a502cc 100755
> --- a/target/linux/mvebu/cortexa72/base-files/lib/upgrade/platform.sh
> +++ b/target/linux/mvebu/cortexa72/base-files/lib/upgrade/platform.sh
> @@ -9,6 +9,8 @@ REQUIRE_IMAGE_METADATA=1
>
> platform_check_image() {
> case "$(board_name)" in
> + iei,puzzle-m901|\
> + iei,puzzle-m902|\
> marvell,armada8040-mcbin-doubleshot|\
> marvell,armada8040-mcbin-singleshot)
> legacy_sdcard_check_image "$1"
> @@ -21,6 +23,10 @@ platform_check_image() {
>
> platform_do_upgrade() {
> case "$(board_name)" in
> + iei,puzzle-m901|\
> + iei,puzzle-m902)
> + platform_do_upgrade_emmc "$1"
> + ;;
> marvell,armada8040-mcbin-doubleshot|\
> marvell,armada8040-mcbin-singleshot)
> legacy_sdcard_do_upgrade "$1"
> @@ -32,6 +38,8 @@ platform_do_upgrade() {
> }
> platform_copy_config() {
> case "$(board_name)" in
> + iei,puzzle-m901|\
> + iei,puzzle-m902|\
> marvell,armada8040-mcbin-doubleshot|\
> marvell,armada8040-mcbin-singleshot)
> legacy_sdcard_copy_config
> diff --git a/target/linux/mvebu/files/arch/arm64/boot/dts/marvell/cn9131-puzzle-m901.dts b/target/linux/mvebu/files/arch/arm64/boot/dts/marvell/cn9131-puzzle-m901.dts
> new file mode 100644
> index 0000000000..58e749490a
> --- /dev/null
> +++ b/target/linux/mvebu/files/arch/arm64/boot/dts/marvell/cn9131-puzzle-m901.dts
> @@ -0,0 +1,319 @@
> +// SPDX-License-Identifier: (GPL-2.0-or-later OR MIT)
> +/*
> + * Copyright (C) 2019 Marvell International Ltd.
> + *
> + * Device tree for the CN9131-DB board.
> + */
> +
> +#include "cn9130.dtsi"
> +
> +#include <dt-bindings/gpio/gpio.h>
> +
> +/ {
> + model = "iEi Puzzle-M901";
> + compatible = "iei,puzzle-m901",
> + "marvell,armada-ap807-quad", "marvell,armada-ap807";
> +
> + chosen {
> + stdout-path = "serial0:115200n8";
> + };
> +
> + aliases {
> + i2c0 = &cp1_i2c0;
> + i2c1 = &cp0_i2c0;
> + ethernet0 = &cp0_eth0;
> + ethernet1 = &cp0_eth1;
> + ethernet2 = &cp0_eth2;
> + ethernet3 = &cp1_eth0;
> + ethernet4 = &cp1_eth1;
> + ethernet5 = &cp1_eth2;
> + gpio1 = &cp0_gpio1;
> + gpio2 = &cp0_gpio2;
> + gpio3 = &cp1_gpio1;
> + gpio4 = &cp1_gpio2;
> + };
> +
> + memory at 00000000 {
> + device_type = "memory";
> + reg = <0x0 0x0 0x0 0x80000000>;
> + };
> +};
> +
> +&uart0 {
> + status = "okay";
> +};
> +
> +&cp0_uart0 {
> + status = "okay";
> +};
> +
> +/* on-board eMMC - U9 */
> +&ap_sdhci0 {
> + pinctrl-names = "default";
> + bus-width = <8>;
> + status = "okay";
> + mmc-ddr-1_8v;
> + mmc-hs400-1_8v;
> +};
> +
> +&cp0_crypto {
> + status = "okay";
> +};
> +
> +&cp0_xmdio {
> + status = "okay";
> + cp0_nbaset_phy0: ethernet-phy at 0 {
> + compatible = "ethernet-phy-ieee802.3-c45";
> + reg = <2>;
> + };
> + cp0_nbaset_phy1: ethernet-phy at 1 {
> + compatible = "ethernet-phy-ieee802.3-c45";
> + reg = <0>;
> + };
> + cp0_nbaset_phy2: ethernet-phy at 2 {
> + compatible = "ethernet-phy-ieee802.3-c45";
> + reg = <8>;
> + };
> +};
> +
> +&cp0_ethernet {
> + status = "okay";
> +};
> +
> +/* SLM-1521-V2, CON9 */
> +&cp0_eth0 {
> + status = "okay";
> + phy-mode = "2500base-x";
> + phys = <&cp0_comphy2 0>;
> + managed = "in-band-status";
> +};
> +
> +&cp0_eth1 {
> + status = "okay";
> + phy-mode = "2500base-x";
> + phys = <&cp0_comphy4 1>;
> + managed = "in-band-status";
> +};
> +
> +&cp0_eth2 {
> + status = "okay";
> + phy-mode = "2500base-x";
> + phys = <&cp0_comphy5 2>;
> + managed = "in-band-status";
> +};
> +
> +&cp0_gpio1 {
> + status = "okay";
> +};
> +
> +&cp0_gpio2 {
> + status = "okay";
> +};
> +
> +&cp0_i2c0 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&cp0_i2c0_pins>;
> + status = "okay";
> + clock-frequency = <100000>;
> + rtc at 32 {
> + compatible = "epson,rx8130";
> + reg = <0x32>;
> + wakeup-source;
> + };
> +};
> +
> +/* SLM-1521-V2, CON6 */
> +&cp0_pcie0 {
> + status = "okay";
> + num-lanes = <2>;
> + num-viewport = <8>;
> + phys = <&cp0_comphy0 0>, <&cp0_comphy1 0>;
> +};
> +
> +/* U55 */
> +&cp0_spi1 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&cp0_spi0_pins>;
> + reg = <0x700680 0x50>, /* control */
> + <0x2000000 0x1000000>; /* CS0 */
> + status = "okay";
> + spi-flash at 0 {
> + #address-cells = <0x1>;
> + #size-cells = <0x1>;
> + compatible = "jedec,spi-nor";
> + reg = <0x0>;
> + spi-max-frequency = <40000000>;
> + partitions {
> + compatible = "fixed-partitions";
> + #address-cells = <1>;
> + #size-cells = <1>;
> + partition at 0 {
> + label = "U-Boot";
> + reg = <0x0 0x1f0000>;
> + };
> + partition at 1f0000 {
> + label = "U-Boot ENV Factory";
> + reg = <0x1f0000 0x10000>;
> + };
> + partition at 200000 {
> + label = "Reserved";
> + reg = <0x200000 0x1f0000>;
> + };
> + partition at 3f0000 {
> + label = "U-Boot ENV";
> + reg = <0x3f0000 0x10000>;
> + };
> + };
> + };
> +};
> +
> +&cp0_syscon0 {
> + cp0_pinctrl: pinctrl {
> + compatible = "marvell,cp115-standalone-pinctrl";
> + cp0_i2c0_pins: cp0-i2c-pins-0 {
> + marvell,pins = "mpp37", "mpp38";
> + marvell,function = "i2c0";
> + };
> + cp0_i2c1_pins: cp0-i2c-pins-1 {
> + marvell,pins = "mpp35", "mpp36";
> + marvell,function = "i2c1";
> + };
> + cp0_ge1_rgmii_pins: cp0-ge-rgmii-pins-0 {
> + marvell,pins = "mpp0", "mpp1", "mpp2",
> + "mpp3", "mpp4", "mpp5",
> + "mpp6", "mpp7", "mpp8",
> + "mpp9", "mpp10", "mpp11";
> + marvell,function = "ge0";
> + };
> + cp0_ge2_rgmii_pins: cp0-ge-rgmii-pins-1 {
> + marvell,pins = "mpp44", "mpp45", "mpp46",
> + "mpp47", "mpp48", "mpp49",
> + "mpp50", "mpp51", "mpp52",
> + "mpp53", "mpp54", "mpp55";
> + marvell,function = "ge1";
> + };
> + cp0_spi0_pins: cp0-spi-pins-0 {
> + marvell,pins = "mpp13", "mpp14", "mpp15", "mpp16";
> + marvell,function = "spi1";
> + };
> + };
> +};
> +
> +/*
> + * Instantiate the first connected CP115
> + */
> +
> +#define CP11X_NAME cp1
> +#define CP11X_BASE f6000000
> +#define CP11X_PCIEx_MEM_BASE(iface) (0xe2000000 + (iface * 0x1000000))
> +#define CP11X_PCIEx_MEM_SIZE(iface) 0xf00000
> +#define CP11X_PCIE0_BASE f6600000
> +#define CP11X_PCIE1_BASE f6620000
> +#define CP11X_PCIE2_BASE f6640000
> +
> +#include "armada-cp115.dtsi"
> +
> +#undef CP11X_NAME
> +#undef CP11X_BASE
> +#undef CP11X_PCIEx_MEM_BASE
> +#undef CP11X_PCIEx_MEM_SIZE
> +#undef CP11X_PCIE0_BASE
> +#undef CP11X_PCIE1_BASE
> +#undef CP11X_PCIE2_BASE
> +
> +&cp1_crypto {
> + status = "okay";
> +};
> +
> +&cp1_xmdio {
> + status = "okay";
> + cp1_nbaset_phy0: ethernet-phy at 3 {
> + compatible = "ethernet-phy-ieee802.3-c45";
> + reg = <2>;
> + };
> + cp1_nbaset_phy1: ethernet-phy at 4 {
> + compatible = "ethernet-phy-ieee802.3-c45";
> + reg = <0>;
> + };
> + cp1_nbaset_phy2: ethernet-phy at 5 {
> + compatible = "ethernet-phy-ieee802.3-c45";
> + reg = <8>;
> + };
> +};
> +
> +&cp1_ethernet {
> + status = "okay";
> +};
> +
> +/* CON50 */
> +&cp1_eth0 {
> + status = "okay";
> + phy-mode = "2500base-x";
> + phys = <&cp1_comphy2 0>;
> + managed = "in-band-status";
> +};
> +
> +&cp1_eth1 {
> + status = "okay";
> + phy-mode = "2500base-x";
> + phys = <&cp1_comphy4 1>;
> + managed = "in-band-status";
> +};
> +
> +&cp1_eth2 {
> + status = "okay";
> + phy-mode = "2500base-x";
> + phys = <&cp1_comphy5 2>;
> + managed = "in-band-status";
> +};
> +
> +&cp1_sata0 {
> + status = "okay";
> + sata-port at 1 {
> + status = "okay";
> + phys = <&cp1_comphy0 1>;
> + };
> +};
> +
> +&cp1_gpio1 {
> + status = "okay";
> +};
> +
> +&cp1_gpio2 {
> + status = "okay";
> +};
> +
> +&cp1_i2c0 {
> + status = "okay";
> + pinctrl-names = "default";
> + pinctrl-0 = <&cp1_i2c0_pins>;
> + clock-frequency = <100000>;
> +};
> +
> +&cp1_syscon0 {
> + cp1_pinctrl: pinctrl {
> + compatible = "marvell,cp115-standalone-pinctrl";
> + cp1_i2c0_pins: cp1-i2c-pins-0 {
> + marvell,pins = "mpp37", "mpp38";
> + marvell,function = "i2c0";
> + };
> + cp1_spi0_pins: cp1-spi-pins-0 {
> + marvell,pins = "mpp13", "mpp14", "mpp15", "mpp16";
> + marvell,function = "spi1";
> + };
> + cp1_xhci0_vbus_pins: cp1-xhci0-vbus-pins {
> + marvell,pins = "mpp3";
> + marvell,function = "gpio";
> + };
> + cp1_sfp_pins: sfp-pins {
> + marvell,pins = "mpp8", "mpp9", "mpp10", "mpp11";
> + marvell,function = "gpio";
> + };
> + };
> +};
> +
> +&cp1_usb3_1 {
> + status = "okay";
> + phys = <&cp1_comphy3 1>;
> + phy-names = "usb";
> +};
> diff --git a/target/linux/mvebu/files/arch/arm64/boot/dts/marvell/cn9132-puzzle-m902.dts b/target/linux/mvebu/files/arch/arm64/boot/dts/marvell/cn9132-puzzle-m902.dts
> new file mode 100644
> index 0000000000..dc4e6527f1
> --- /dev/null
> +++ b/target/linux/mvebu/files/arch/arm64/boot/dts/marvell/cn9132-puzzle-m902.dts
> @@ -0,0 +1,481 @@
> +// SPDX-License-Identifier: (GPL-2.0-or-later OR MIT)
> +/*
> + * Copyright (C) 2019 Marvell International Ltd.
> + *
> + * Device tree for the CN9132-DB board.
> + */
> +
> +#include "cn9130.dtsi"
> +
> +#include <dt-bindings/gpio/gpio.h>
> +
> +/ {
> + model = "iEi Puzzle-M902";
> + compatible = "iei,puzzle-m902",
> + "marvell,armada-ap807-quad", "marvell,armada-ap807";
> +
> + chosen {
> + stdout-path = "serial0:115200n8";
> + };
> +
> + aliases {
> + i2c0 = &cp1_i2c0;
> + i2c1 = &cp0_i2c0;
> + gpio1 = &cp0_gpio1;
> + gpio2 = &cp0_gpio2;
> + gpio3 = &cp1_gpio1;
> + gpio4 = &cp1_gpio2;
> + gpio5 = &cp2_gpio1;
> + gpio6 = &cp2_gpio2;
> + ethernet0 = &cp0_eth0;
> + ethernet1 = &cp0_eth1;
> + ethernet2 = &cp0_eth2;
> + ethernet3 = &cp1_eth0;
> + ethernet4 = &cp1_eth1;
> + ethernet5 = &cp1_eth2;
> + ethernet6 = &cp2_eth0;
> + ethernet7 = &cp2_eth1;
> + ethernet8 = &cp2_eth2;
> + spi1 = &cp0_spi0;
> + spi2 = &cp0_spi1;
> + serial1 = &cp0_uart0;
> + };
> +
> + memory at 00000000 {
> + device_type = "memory";
> + reg = <0x0 0x0 0x0 0x80000000>;
> + };
> +
> + cp2_reg_usb3_vbus0: cp2_usb3_vbus at 0 {
> + compatible = "regulator-fixed";
> + regulator-name = "cp2-xhci0-vbus";
> + regulator-min-microvolt = <5000000>;
> + regulator-max-microvolt = <5000000>;
> + enable-active-high;
> + gpio = <&cp2_gpio1 2 GPIO_ACTIVE_HIGH>;
> + };
> +
> + cp2_usb3_0_phy0: cp2_usb3_phy0 {
> + compatible = "usb-nop-xceiv";
> + vcc-supply = <&cp2_reg_usb3_vbus0>;
> + };
> +
> + cp2_reg_usb3_vbus1: cp2_usb3_vbus at 1 {
> + compatible = "regulator-fixed";
> + regulator-name = "cp2-xhci1-vbus";
> + regulator-min-microvolt = <5000000>;
> + regulator-max-microvolt = <5000000>;
> + enable-active-high;
> + gpio = <&cp2_gpio1 3 GPIO_ACTIVE_HIGH>;
> + };
> +
> + cp2_usb3_0_phy1: cp2_usb3_phy1 {
> + compatible = "usb-nop-xceiv";
> + vcc-supply = <&cp2_reg_usb3_vbus1>;
> + };
> +
> + cp2_sfp_eth0: sfp-eth0 {
> + compatible = "sff,sfp";
> + i2c-bus = <&cp2_sfpp0_i2c>;
> + los-gpio = <&cp2_module_expander1 11 GPIO_ACTIVE_HIGH>;
> + mod-def0-gpio = <&cp2_module_expander1 10 GPIO_ACTIVE_LOW>;
> + tx-disable-gpio = <&cp2_module_expander1 9 GPIO_ACTIVE_HIGH>;
> + tx-fault-gpio = <&cp2_module_expander1 8 GPIO_ACTIVE_HIGH>;
> + status = "disabled";
> + };
> +};
> +
> +&uart0 {
> + status = "okay";
> +};
> +
> +&cp0_uart0 {
> + status = "okay";
> +};
> +
> +/* on-board eMMC - U9 */
> +&ap_sdhci0 {
> + pinctrl-names = "default";
> + bus-width = <8>;
> + status = "okay";
> + mmc-ddr-1_8v;
> + mmc-hs400-1_8v;
> +};
> +
> +&cp0_crypto {
> + status = "okay";
> +};
> +
> +&cp0_xmdio {
> + status = "okay";
> + cp0_nbaset_phy0: ethernet-phy at 0 {
> + compatible = "ethernet-phy-ieee802.3-c45";
> + reg = <2>;
> + };
> + cp0_nbaset_phy1: ethernet-phy at 1 {
> + compatible = "ethernet-phy-ieee802.3-c45";
> + reg = <0>;
> + };
> + cp0_nbaset_phy2: ethernet-phy at 2 {
> + compatible = "ethernet-phy-ieee802.3-c45";
> + reg = <8>;
> + };
> +};
> +
> +&cp0_ethernet {
> + status = "okay";
> +};
> +
> +/* SLM-1521-V2, CON9 */
> +&cp0_eth0 {
> + status = "okay";
> + phy-mode = "10gbase-kr";
> + phys = <&cp0_comphy2 0>;
> + managed = "in-band-status";
> +};
> +
> +&cp0_eth1 {
> + status = "okay";
> + phy-mode = "2500base-x";
> + phys = <&cp0_comphy4 1>;
> + managed = "in-band-status";
> +};
> +
> +&cp0_eth2 {
> + status = "okay";
> + phy-mode = "2500base-x";
> + phys = <&cp0_comphy1 2>;
> + managed = "in-band-status";
> +};
> +
> +&cp0_gpio1 {
> + status = "okay";
> +};
> +
> +&cp0_gpio2 {
> + status = "okay";
> +};
> +
> +&cp0_i2c0 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&cp0_i2c0_pins>;
> + status = "okay";
> + clock-frequency = <100000>;
> + rtc at 32 {
> + compatible = "epson,rx8130";
> + reg = <0x32>;
> + wakeup-source;
> + };
> +};
> +
> +&cp0_i2c1 {
> + clock-frequency = <100000>;
> +};
> +
> +/* SLM-1521-V2, CON6 */
> +&cp0_sata0 {
> + status = "okay";
> + sata-port at 1 {
> + status = "okay";
> + phys = <&cp0_comphy0 1>;
> + };
> +};
> +
> +&cp0_pcie2 {
> + status = "okay";
> + num-lanes = <1>;
> + num-viewport = <8>;
> + phys = <&cp0_comphy5 2>;
> +};
> +
> +/* U55 */
> +&cp0_spi1 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&cp0_spi0_pins>;
> + reg = <0x700680 0x50>, /* control */
> + <0x2000000 0x1000000>; /* CS0 */
> + status = "okay";
> + spi-flash at 0 {
> + #address-cells = <0x1>;
> + #size-cells = <0x1>;
> + compatible = "jedec,spi-nor";
> + reg = <0x0>;
> + spi-max-frequency = <40000000>;
> + partitions {
> + compatible = "fixed-partitions";
> + #address-cells = <1>;
> + #size-cells = <1>;
> + partition at 0 {
> + label = "U-Boot";
> + reg = <0x0 0x1f0000>;
> + };
> + partition at 1f0000 {
> + label = "U-Boot ENV Factory";
> + reg = <0x1f0000 0x10000>;
> + };
> + partition at 200000 {
> + label = "Reserved";
> + reg = <0x200000 0x1f0000>;
> + };
> + partition at 3f0000 {
> + label = "U-Boot ENV";
> + reg = <0x3f0000 0x10000>;
> + };
> + };
> + };
> +};
> +
> +&cp0_syscon0 {
> + cp0_pinctrl: pinctrl {
> + compatible = "marvell,cp115-standalone-pinctrl";
> + cp0_i2c0_pins: cp0-i2c-pins-0 {
> + marvell,pins = "mpp37", "mpp38";
> + marvell,function = "i2c0";
> + };
> + cp0_i2c1_pins: cp0-i2c-pins-1 {
> + marvell,pins = "mpp35", "mpp36";
> + marvell,function = "i2c1";
> + };
> + cp0_ge1_rgmii_pins: cp0-ge-rgmii-pins-0 {
> + marvell,pins = "mpp0", "mpp1", "mpp2",
> + "mpp3", "mpp4", "mpp5",
> + "mpp6", "mpp7", "mpp8",
> + "mpp9", "mpp10", "mpp11";
> + marvell,function = "ge0";
> + };
> + cp0_ge2_rgmii_pins: cp0-ge-rgmii-pins-1 {
> + marvell,pins = "mpp44", "mpp45", "mpp46",
> + "mpp47", "mpp48", "mpp49",
> + "mpp50", "mpp51", "mpp52",
> + "mpp53", "mpp54", "mpp55";
> + marvell,function = "ge1";
> + };
> + cp0_spi0_pins: cp0-spi-pins-0 {
> + marvell,pins = "mpp13", "mpp14", "mpp15", "mpp16";
> + marvell,function = "spi1";
> + };
> + };
> +};
> +
> +&cp0_usb3_1 {
> + status = "okay";
> + phys = <&cp0_comphy3 1>;
> + phy-names = "usb";
> +};
> +
> +/*
> + * Instantiate the first connected CP115
> + */
> +
> +#define CP11X_NAME cp1
> +#define CP11X_BASE f4000000
> +#define CP11X_PCIEx_MEM_BASE(iface) (0xe2000000 + (iface * 0x1000000))
> +#define CP11X_PCIEx_MEM_SIZE(iface) 0xf00000
> +#define CP11X_PCIE0_BASE f4600000
> +#define CP11X_PCIE1_BASE f4620000
> +#define CP11X_PCIE2_BASE f4640000
> +
> +#include "armada-cp115.dtsi"
> +
> +#undef CP11X_NAME
> +#undef CP11X_BASE
> +#undef CP11X_PCIEx_MEM_BASE
> +#undef CP11X_PCIEx_MEM_SIZE
> +#undef CP11X_PCIE0_BASE
> +#undef CP11X_PCIE1_BASE
> +#undef CP11X_PCIE2_BASE
> +
> +&cp1_crypto {
> + status = "okay";
> +};
> +
> +&cp1_xmdio {
> + status = "okay";
> + cp1_nbaset_phy0: ethernet-phy at 3 {
> + compatible = "ethernet-phy-ieee802.3-c45";
> + reg = <2>;
> + };
> + cp1_nbaset_phy1: ethernet-phy at 4 {
> + compatible = "ethernet-phy-ieee802.3-c45";
> + reg = <0>;
> + };
> + cp1_nbaset_phy2: ethernet-phy at 5 {
> + compatible = "ethernet-phy-ieee802.3-c45";
> + reg = <8>;
> + };
> +};
> +
> +&cp1_ethernet {
> + status = "okay";
> +};
> +
> +/* CON50 */
> +&cp1_eth0 {
> + status = "okay";
> + phy-mode = "10gbase-kr";
> + phys = <&cp1_comphy2 0>;
> + managed = "in-band-status";
> +};
> +
> +&cp1_eth1 {
> + status = "okay";
> + phy-mode = "2500base-x";
> + phys = <&cp1_comphy4 1>;
> + managed = "in-band-status";
> +};
> +
> +&cp1_eth2 {
> + status = "okay";
> + phy-mode = "2500base-x";
> + phys = <&cp1_comphy1 2>;
> + managed = "in-band-status";
> +};
> +
> +&cp1_gpio1 {
> + status = "okay";
> +};
> +
> +&cp1_gpio2 {
> + status = "okay";
> +};
> +
> +&cp1_i2c0 {
> + status = "okay";
> + pinctrl-names = "default";
> + pinctrl-0 = <&cp1_i2c0_pins>;
> + clock-frequency = <100000>;
> +};
> +
> +&cp1_syscon0 {
> + cp1_pinctrl: pinctrl {
> + compatible = "marvell,cp115-standalone-pinctrl";
> + cp1_i2c0_pins: cp1-i2c-pins-0 {
> + marvell,pins = "mpp37", "mpp38";
> + marvell,function = "i2c0";
> + };
> + cp1_spi0_pins: cp1-spi-pins-0 {
> + marvell,pins = "mpp13", "mpp14", "mpp15", "mpp16";
> + marvell,function = "spi1";
> + };
> + cp1_xhci0_vbus_pins: cp1-xhci0-vbus-pins {
> + marvell,pins = "mpp3";
> + marvell,function = "gpio";
> + };
> + };
> +};
> +
> +/*
> + * Instantiate the second connected CP115
> + */
> +
> +#define CP11X_NAME cp2
> +#define CP11X_BASE f6000000
> +#define CP11X_PCIEx_MEM_BASE(iface) (0xe5000000 + (iface * 0x1000000))
> +#define CP11X_PCIEx_MEM_SIZE(iface) 0xf00000
> +#define CP11X_PCIE0_BASE f6600000
> +#define CP11X_PCIE1_BASE f6620000
> +#define CP11X_PCIE2_BASE f6640000
> +
> +#include "armada-cp115.dtsi"
> +
> +#undef CP11X_NAME
> +#undef CP11X_BASE
> +#undef CP11X_PCIEx_MEM_BASE
> +#undef CP11X_PCIEx_MEM_SIZE
> +#undef CP11X_PCIE0_BASE
> +#undef CP11X_PCIE1_BASE
> +#undef CP11X_PCIE2_BASE
> +
> +&cp2_crypto {
> + status = "okay";
> +};
> +
> +&cp2_ethernet {
> + status = "okay";
> +};
> +
> +&cp2_xmdio {
> + status = "okay";
> + cp2_nbaset_phy0: ethernet-phy at 6 {
> + compatible = "ethernet-phy-ieee802.3-c45";
> + reg = <2>;
> + };
> + cp2_nbaset_phy1: ethernet-phy at 7 {
> + compatible = "ethernet-phy-ieee802.3-c45";
> + reg = <0>;
> + };
> + cp2_nbaset_phy2: ethernet-phy at 8 {
> + compatible = "ethernet-phy-ieee802.3-c45";
> + reg = <8>;
> + };
> +};
> +
> +/* SLM-1521-V2, CON9 */
> +&cp2_eth0 {
> + status = "okay";
> + phy-mode = "10gbase-kr";
> + phys = <&cp2_comphy2 0>;
> + managed = "in-band-status";
> +};
> +
> +&cp2_eth1 {
> + status = "okay";
> + phy-mode = "2500base-x";
> + phys = <&cp2_comphy4 1>;
> + managed = "in-band-status";
> +};
> +
> +&cp2_eth2 {
> + status = "okay";
> + phy-mode = "2500base-x";
> + phys = <&cp2_comphy1 2>;
> + managed = "in-band-status";
> +};
> +
> +&cp2_gpio1 {
> + status = "okay";
> +};
> +
> +&cp2_gpio2 {
> + status = "okay";
> +};
> +
> +&cp2_i2c0 {
> + clock-frequency = <100000>;
> + /* SLM-1521-V2 - U3 */
> + i2c-mux at 72 {
> + compatible = "nxp,pca9544";
> + #address-cells = <1>;
> + #size-cells = <0>;
> + reg = <0x72>;
> + cp2_sfpp0_i2c: i2c at 0 {
> + #address-cells = <1>;
> + #size-cells = <0>;
> + reg = <0>;
> + };
> +
> + i2c at 1 {
> + #address-cells = <1>;
> + #size-cells = <0>;
> + reg = <1>;
> + /* U12 */
> + cp2_module_expander1: pca9555 at 21 {
> + compatible = "nxp,pca9555";
> + pinctrl-names = "default";
> + gpio-controller;
> + #gpio-cells = <2>;
> + reg = <0x21>;
> + };
> + };
> + };
> +};
> +
> +&cp2_syscon0 {
> + cp2_pinctrl: pinctrl {
> + compatible = "marvell,cp115-standalone-pinctrl";
> + cp2_i2c0_pins: cp2-i2c-pins-0 {
> + marvell,pins = "mpp37", "mpp38";
> + marvell,function = "i2c0";
> + };
> + };
> +};
> diff --git a/target/linux/mvebu/image/cortexa72.mk b/target/linux/mvebu/image/cortexa72.mk
> index 1440c07a0b..29727f8b9d 100644
> --- a/target/linux/mvebu/image/cortexa72.mk
> +++ b/target/linux/mvebu/image/cortexa72.mk
> @@ -43,3 +43,21 @@ define Device/marvell_macchiatobin-singleshot
> SUPPORTED_DEVICES := marvell,armada8040-mcbin-singleshot
> endef
> TARGET_DEVICES += marvell_macchiatobin-singleshot
> +
> +define Device/iei_puzzle-m901
> + $(call Device/Default-arm64)
> + DEVICE_VENDOR := iEi
> + DEVICE_MODEL := Puzzle-M901
> + SOC := cn9131
> + IMAGE/sdcard.img.gz := boot-img-ext4 | sdcard-img-ext4 | gzip | append-metadata
> +endef
> +TARGET_DEVICES += iei_puzzle-m901
> +
> +define Device/iei_puzzle-m902
> + $(call Device/Default-arm64)
> + DEVICE_VENDOR := iEi
> + DEVICE_MODEL := Puzzle-M902
> + SOC := cn9132
> + IMAGE/sdcard.img.gz := boot-img-ext4 | sdcard-img-ext4 | gzip | append-metadata
> +endef
> +TARGET_DEVICES += iei_puzzle-m902
-------------- next part --------------
A non-text attachment was scrubbed...
Name: OpenPGP_signature
Type: application/pgp-signature
Size: 665 bytes
Desc: OpenPGP digital signature
URL: <http://lists.openwrt.org/pipermail/openwrt-devel/attachments/20210902/c7b7f959/attachment-0001.sig>
More information about the openwrt-devel
mailing list