[OpenWrt-Devel] [PATCH v6] ramips: add support for Trendnet TEW-810DR
Daniel Golle
daniel at makrotopia.org
Mon May 25 20:11:11 EDT 2020
On Mon, May 25, 2020 at 05:05:16PM -0700, Heppler, J. Scott wrote:
>
> * MediaTek MT7620A (580 Mhz)
> * 8 MB of FLASH
> * 64 MB of RAM
> * 2.4Ghz and 5.0Ghz radios both now functional
> * 5x 10/100 Mbps Ethernet (1 WAN and 4 LAN)
> * UART header on PCB (57600 8n1)
> * Green/Orange Power LEDs illuminating a Power-Button Lens
> Green/Orange Internet LEDs GPIO controlled illuminating a Globe/Internet Lens
> * 3x button - wps, power and reset
> * U-boot bootloader
>
> Installation:
>
> The sysupgrade.bin image is reported to be OEM web flashed with an ncc_att_hwid
> appended. ncc_att_hwid is a 32bit binary in the GPL Source download for either
> the TEW-810DR or DIR-810L and is located at
> source/user/wolf/cameo/ncc/hostTools.
> The invocation is: ncc_att_hwid
> -f tew-810dr-squashfs-factory.bin -a -m "TEW-810DR" -H "1.0R" -r "WW" -c "1.0"
> This may need to be altered if your hardware version is "1.1R".
> The image can also be directly flashed via serial tftp.
> 1. Load *.sysupgrade.bin to your tftp server directory and rename for
> convenience.
> 2. Set a static ip 192.168.10.100.
> 3. NIC cable to a lan port.
> 4. Serial connection parameters 57600,8N1
> 5. Power on the TEW-810 and press 4 for a u-boot command line prompt.
> 6. Verify IP's with U-Boot command "printenv".
> 7. Adjust tftp settings if needed per the tftp documentation
> 8. Boot the tftp image to test the build.
> 9. If the image loads, reset your server ip to 192.168.1.10 and restart network.
> 10. Log in to Luci, 192.168.1.1, and flash the *sysupgrade.bin image.
>
> Signed-off-by: J. Scott Heppler <shep971 at centurylink.net>
>
> Summary v4 -> v5
> 1. Enumerated installation steps and corrected grammar.
> 2. Added SPDX License Identifier to *.dts.
> 3. gpio-keys-polled -> gpio-keys in *.dts.
> 4. gpio2 0 is actually behind a Globe/Internet lens - changed to wan.
> 5. Increased spi-max-frequency 10000000 -> 50000000
> 6. jffs2 partition 0xe0000 -> 0xf0000.
> 7. &state_default groups dropped mdio, rgmii1, wled.
> 8. MAC assignments mirror DIR-810L and verify in Luci. Unchanged
> 02_network and *.dts.
> 9. 01_leds changed consistent with #4.
> 10. Removed SUPPORTED_DEVICES from image/mt7620.mk. Note: the D-Link
> DIR-810L has the same SUPPORTED_DEVICES entry in image/mt7620.mk.
> 11. Builds/Runs on my test Device.
> ---
> .../ramips/dts/mt7620a_trendnet_tew-810dr.dts | 166 ++++++++++++++++++
> target/linux/ramips/image/mt7620.mk | 9 +
> .../mt7620/base-files/etc/board.d/01_leds | 3 +
> .../mt7620/base-files/etc/board.d/02_network | 8 +-
> 4 files changed, 183 insertions(+), 3 deletions(-)
> create mode 100644 target/linux/ramips/dts/mt7620a_trendnet_tew-810dr.dts
>
> diff --git a/target/linux/ramips/dts/mt7620a_trendnet_tew-810dr.dts b/target/linux/ramips/dts/mt7620a_trendnet_tew-810dr.dts
> new file mode 100644
> index 0000000000..5012d39b51
> --- /dev/null
> +++ b/target/linux/ramips/dts/mt7620a_trendnet_tew-810dr.dts
> @@ -0,0 +1,166 @@
> +//SPDX-License-Identifier: GPL-2.0-or-later OR MIT
> +/dts-v1/;
> +
> +#include "mt7620a.dtsi"
> +
> +#include <dt-bindings/gpio/gpio.h>
> +#include <dt-bindings/input/input.h>
> +
> +/ {
> + compatible = "trendnet,tew-810dr", "ralink,mt7620a-soc";
> + model = "TRENDnet TEW-810DR";
> +
> + aliases {
> + led-boot = &led_power_green;
> + led-failsafe = &led_power_green;
> + led-running = &led_power_green;
> + led-upgrade = &led_power_green;
> + label-mac-device = ðernet;
> + };
> +
> + keys {
> + compatible = "gpio-keys";
> +
> + reset {
> + label = "reset";
> + gpios = <&gpio0 1 GPIO_ACTIVE_LOW>;
> + linux,code = <KEY_RESTART>;
> + };
> +
> + wps {
> + label = "wps";
> + gpios = <&gpio0 2 GPIO_ACTIVE_LOW>;
> + linux,code = <KEY_WPS_BUTTON>;
> + };
> + };
> +
> + leds {
> + compatible = "gpio-leds";
> +
> + led_power_green: power_green {
> + label = "tew-810dr:green:power";
> + gpios = <&gpio0 9 GPIO_ACTIVE_HIGH>;
> + };
> +
> + wan_orange: wan_orange {
> + label = "tew-810dr:orange:wan";
> + gpios = <&gpio0 12 GPIO_ACTIVE_HIGH>;
> + };
> +
> + wan_green: wan_green {
> + label = "tew-810dr:green:wan";
> + gpios = <&gpio2 0 GPIO_ACTIVE_LOW>;
> + };
> +
> + led_power_orange {
> + label = "tew-810dr:orange:power";
> + gpios = <&gpio0 13 GPIO_ACTIVE_HIGH>;
> + };
> + };
> +};
> +
> +&spi0 {
> + status = "okay";
> +
> + flash at 0 {
> + compatible = "jedec,spi-nor";
> + reg = <0>;
> + spi-max-frequency = <50000000>;
> +
> + partitions {
> + compatible = "fixed-partitions";
> + #address-cells = <1>;
> + #size-cells = <1>;
> +
> + partition at 0 {
> + label = "u-boot";
> + reg = <0x0 0x30000>;
> + read-only;
> + };
> +
> + partition at 30000 {
> + label = "u-boot-env";
> + reg = <0x30000 0x10000>;
> + read-only;
> + };
> +
> + factory: partition at 40000 {
> + label = "factory";
> + reg = <0x40000 0x10000>;
> + read-only;
> + };
> +
> + factory5g: partition at 50000 {
> + label = "factory5g";
> + reg = <0x50000 0x10000>;
> + read-only;
> + };
> +
> + partition at 60000 {
> + label = "Wolf_Config";
> + reg = <0x60000 0x10000>;
> + read-only;
> + };
> +
> + partition at 70000 {
> + label = "MyDlink";
> + reg = <0x70000 0x80000>;
> + read-only;
> + };
> +
> + partition at f0000 {
> + label = "Jffs2";
> + reg = <0xf0000 0x80000>;
> + read-only;
> + };
> +
> + partition at 170000 {
> + compatible = "denx,uimage";
> + label = "firmware";
> + reg = <0x170000 0x690000>;
> + };
> + };
> + };
> +};
> +
> +&state_default {
> + gpio {
> + groups = "i2c", "uartf", "ephy";
> + function = "gpio";
> + };
> +};
> +
> +ðernet {
> + mtd-mac-address = <&factory 0x28>;
> + mediatek,portmap = "llllw";
> +};
> +
> +&gsw {
> + mediatek,port4 = "ephy";
> +};
> +
> +&pcie {
> + status = "okay";
> +};
> +
> +&wmac {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pa_pins>;
> +
> + ralink,mtd-eeprom = <&factory 0x0>;
white-space is odd here, please fix that and use tab like for the other
properties.
> + mtd-mac-address = <&factory 0x28>;
> +};
> +
> +&pcie0 {
> + wifi at 0,0 {
> + reg = <0x0000 0 0 0 0>;
> + mediatek,mtd-eeprom = <&factory 0x8000>;
> + ieee80211-freq-limit = <5000000 6000000>;
> + mtd-mac-address = <&factory 0x28>;
> + mtd-mac-address-increment = <2>;
> + };
> +};
> +
> +&gpio2 {
> + status = "okay";
> +};
> diff --git a/target/linux/ramips/image/mt7620.mk b/target/linux/ramips/image/mt7620.mk
> index e435b1d15f..386809e40f 100644
> --- a/target/linux/ramips/image/mt7620.mk
> +++ b/target/linux/ramips/image/mt7620.mk
> @@ -1005,6 +1005,15 @@ define Device/tplink_re210-v1
> endef
> TARGET_DEVICES += tplink_re210-v1
> +define Device/trendnet_tew-810dr
> + SOC := mt7620a
> + DEVICE_PACKAGES := kmod-mt76x0e
> + DEVICE_VENDOR := TRENDnet
> + DEVICE_MODEL := TEW-810DR
> + IMAGE_SIZE := 6720k
> +endef
> +TARGET_DEVICES += trendnet_tew-810dr
> +
> define Device/vonets_var11n-300
> SOC := mt7620n
> IMAGE_SIZE := 3776k
> diff --git a/target/linux/ramips/mt7620/base-files/etc/board.d/01_leds b/target/linux/ramips/mt7620/base-files/etc/board.d/01_leds
> index c1deae59e3..595f84f5d2 100755
> --- a/target/linux/ramips/mt7620/base-files/etc/board.d/01_leds
> +++ b/target/linux/ramips/mt7620/base-files/etc/board.d/01_leds
> @@ -191,6 +191,9 @@ tplink,archer-mr200)
> tplink,re200-v1)
> ucidef_set_led_netdev "lan" "lan" "$boardname:green:lan" "eth0"
> ;;
> +trendnet,tew-810dr)
> + ucidef_set_led_netdev "wan" "wan" "$boardname:green:wan" "eth0.2" "link tx rx"
> + ;;
and here as well. please use tabs instead of spaces to be consistent
with the rest of the file.
> youku,yk1)
> set_wifi_led "$boardname:blue:air"
> ucidef_set_led_switch "wan" "wan" "$boardname:blue:wan" "switch0" "0x10"
> diff --git a/target/linux/ramips/mt7620/base-files/etc/board.d/02_network b/target/linux/ramips/mt7620/base-files/etc/board.d/02_network
> index d024674c10..3fc0ce3049 100755
> --- a/target/linux/ramips/mt7620/base-files/etc/board.d/02_network
> +++ b/target/linux/ramips/mt7620/base-files/etc/board.d/02_network
> @@ -26,6 +26,7 @@ ramips_setup_interfaces()
> ralink,mt7620a-mt7610e-evb|\
> ralink,mt7620a-v22sg-evb|\
> sanlinking,d240|\
> + trendnet,tew-810dr|\
> youku,yk1|\
> zbtlink,zbt-ape522ii|\
> zbtlink,zbt-we826-16m|\
> @@ -259,9 +260,10 @@ ramips_setup_macs()
> alfa-network,ac1200rm|\
> dlink,dir-810l|\
> phicomm,psg1218a|\
> - phicomm,psg1218b)
> - wan_mac=$(macaddr_add "$(mtd_get_mac_binary factory 0x28)" 1)
> - ;;
> + phicomm,psg1218b|\
> + trendnet,tew-810dr)
> + wan_mac=$(macaddr_add "$(mtd_get_mac_binary factory 0x28)" 1)
> + ;;
and here.
> alfa-network,r36m-e4g|\
> zbtlink,zbt-we1026-h-32m)
> wan_mac=$(mtd_get_mac_binary factory 0x2e)
> --
> 2.20.1
lgtm apart from than the white-space issues.
Cheers
Daniel
>
>
> --
> J. Scott Heppler
>
> _______________________________________________
> openwrt-devel mailing list
> openwrt-devel at lists.openwrt.org
> https://lists.openwrt.org/mailman/listinfo/openwrt-devel
_______________________________________________
openwrt-devel mailing list
openwrt-devel at lists.openwrt.org
https://lists.openwrt.org/mailman/listinfo/openwrt-devel
More information about the openwrt-devel
mailing list