[OpenWrt-Devel] [19.07] [PATCH] ath79: add support for Sitecom WLR-7100
mail at adrianschmutzler.de
mail at adrianschmutzler.de
Mon May 4 14:31:15 EDT 2020
Hi,
> -----Original Message-----
> From: openwrt-devel [mailto:openwrt-devel-bounces at lists.openwrt.org]
> On Behalf Of Tomasz Maciej Nowak
> Sent: Montag, 4. Mai 2020 19:49
> To: openwrt-devel at lists.openwrt.org
> Subject: [OpenWrt-Devel] [19.07] [PATCH] ath79: add support for Sitecom
> WLR-7100
>
> Backported from: 1bc921f419df508c57dc07cd3e43cdf0408c17dd
Device support is typically not backported to stable branches, unless you have a very good reason for it.
Best
Adrian
>
> Sitecom WLR-7100 v1 002 (marketed as X7 AC1200) is a dual band wireless
> router.
>
> Specification
> SoC: Atheros AR1022
> RAM: 64 MB DDR2
> Flash: 8 MB SPI NOR
> WIFI: 2.4 GHz 2T2R integrated
> 5 GHz 2T2R QCA9882 integrated (connected to PCIe lane)
> Ethernet: 5x 10/100/1000 Mbps QCA8337N
> USB: 1x 2.0
> LEDS: 4x GPIO controlled, 5x switch
> Buttons: 2x GPIO controlled
> UART: row of 4 unpopulated holes near USB port, starting count from
> white triangle on PCB
> 1. VCC 3.3V, 2. GND, 3. TX, 4. RX
> baud: 115200, parity: none, flow control: none
>
> Installation
> 1. Connect to one of LAN (yellow) ethernet ports, 2. Open router
> configuration interface, 3. Go to Toolbox > Firmware, 4. Browse for OpenWrt
> factory image with dlf extension and hit Apply, 5. Wait few minutes, after the
> Power LED will stop blinking, the router
> is ready for configuration.
>
> Known issues
> 5GHz LED doesn't work
>
> Additional information
> When TX line on UART is connected, and board is switched on from power
> off state, the DDR memory training may fail.
> If connected to UART, when prompted for number on boot, one can enter
> number 4 to open bootloader (U-Boot) command line.
> OEM firmware shell password is: SitecomSenao useful for creating backup of
> original firmware.
> There is also another revision of this device (v1 001), which may or may not
> work with introduced images.
>
> Signed-off-by: Tomasz Maciej Nowak <tomek_n at o2.pl>
> ---
> .../ath79/base-files/etc/board.d/02_network | 6 +
> .../etc/hotplug.d/firmware/10-ath9k-eeprom | 3 +-
> .../etc/hotplug.d/firmware/11-ath10k-caldata | 3 +-
> .../ath79/dts/ar1022_sitecom_wlr-7100.dts | 171 ++++++++++++++++++
> target/linux/ath79/image/generic.mk | 12 ++
> 5 files changed, 193 insertions(+), 2 deletions(-) create mode 100644
> target/linux/ath79/dts/ar1022_sitecom_wlr-7100.dts
>
> diff --git a/target/linux/ath79/base-files/etc/board.d/02_network
> b/target/linux/ath79/base-files/etc/board.d/02_network
> index 1b0e76b1593b..d494c0144725 100755
> --- a/target/linux/ath79/base-files/etc/board.d/02_network
> +++ b/target/linux/ath79/base-files/etc/board.d/02_network
> @@ -150,6 +150,7 @@ ath79_setup_interfaces()
> iodata,wn-ac1600dgr2|\
> iodata,wn-ag300dgr|\
> pcs,cr5000|\
> + sitecom,wlr-7100|\
> wd,mynet-n750)
> ucidef_add_switch "switch0" \
> "0 at eth0" "1:lan" "2:lan" "3:lan" "4:lan" "5:wan"
> @@ -349,6 +350,11 @@ ath79_setup_macs()
> wan_mac=$(mtd_get_mac_binary factory 0)
> lan_mac=$(macaddr_setbit_la "$wan_mac")
> ;;
> + sitecom,wlr-7100)
> + lan_mac=$(mtd_get_mac_ascii u-boot-env ethaddr)
> + wan_mac=$(mtd_get_mac_ascii u-boot-env wanaddr)
> + label_mac=$lan_mac
> + ;;
> tplink,archer-a7-v5|\
> tplink,archer-c7-v4|\
> tplink,archer-c7-v5|\
> diff --git a/target/linux/ath79/base-files/etc/hotplug.d/firmware/10-ath9k-
> eeprom b/target/linux/ath79/base-files/etc/hotplug.d/firmware/10-ath9k-
> eeprom
> index d85e90f10683..69ffad1a99ef 100644
> --- a/target/linux/ath79/base-files/etc/hotplug.d/firmware/10-ath9k-
> eeprom
> +++ b/target/linux/ath79/base-files/etc/hotplug.d/firmware/10-ath9k-eepr
> +++ om
> @@ -119,7 +119,8 @@ case "$FIRMWARE" in
> iodata,wn-ac1167dgr|\
> iodata,wn-ac1600dgr|\
> iodata,wn-ac1600dgr2|\
> - iodata,wn-ag300dgr)
> + iodata,wn-ag300dgr|\
> + sitecom,wlr-7100)
> ath9k_eeprom_extract "art" 4096 1088
> ath9k_patch_fw_mac $(mtd_get_mac_ascii u-boot-env
> ethaddr) 2
> ;;
> diff --git a/target/linux/ath79/base-files/etc/hotplug.d/firmware/11-ath10k-
> caldata b/target/linux/ath79/base-files/etc/hotplug.d/firmware/11-ath10k-
> caldata
> index d93e6dcd71ab..5b29ad0ce9fc 100644
> --- a/target/linux/ath79/base-files/etc/hotplug.d/firmware/11-ath10k-
> caldata
> +++ b/target/linux/ath79/base-files/etc/hotplug.d/firmware/11-ath10k-cal
> +++ data
> @@ -109,7 +109,8 @@ case "$FIRMWARE" in
> ;;
> engenius,epg5000|\
> iodata,wn-ac1167dgr|\
> - iodata,wn-ac1600dgr2)
> + iodata,wn-ac1600dgr2|\
> + sitecom,wlr-7100)
> ath10kcal_extract "art" 20480 2116
> ath10kcal_patch_mac $(macaddr_add $(mtd_get_mac_ascii
> u-boot-env ethaddr) +1)
> ;;
> diff --git a/target/linux/ath79/dts/ar1022_sitecom_wlr-7100.dts
> b/target/linux/ath79/dts/ar1022_sitecom_wlr-7100.dts
> new file mode 100644
> index 000000000000..8a70b597b0fe
> --- /dev/null
> +++ b/target/linux/ath79/dts/ar1022_sitecom_wlr-7100.dts
> @@ -0,0 +1,171 @@
> +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT /dts-v1/;
> +
> +#include <dt-bindings/gpio/gpio.h>
> +#include <dt-bindings/input/input.h>
> +
> +#include "ar9344.dtsi"
> +
> +/ {
> + model = "Sitecom WLR-7100 v1 002 (X7 AC1200)";
> + compatible = "sitecom,wlr-7100", "qca,ar9344";
> +
> + aliases {
> + led-boot = &power;
> + led-failsafe = &power;
> + led-running = &power;
> + led-upgrade = &power;
> + };
> +
> + keys {
> + compatible = "gpio-keys";
> +
> + wlan2g {
> + label = "2.4GHz";
> + gpios = <&gpio 16 GPIO_ACTIVE_LOW>;
> + linux,code = <KEY_RESTART>;
> + };
> +
> + wlan5g {
> + label = "5GHz";
> + gpios = <&gpio 15 GPIO_ACTIVE_LOW>;
> + linux,code = <KEY_WPS_BUTTON>;
> + };
> + };
> +
> + leds {
> + compatible = "gpio-leds";
> +
> + ops {
> + label = "wlr-7100:white:ops";
> + gpios = <&gpio 12 GPIO_ACTIVE_LOW>;
> + };
> +
> + power: power {
> + label = "wlr-7100:amber:power";
> + gpios = <&gpio 2 GPIO_ACTIVE_LOW>;
> + default-state = "on";
> + };
> +
> + wlan2g {
> + label = "wlr-7100:blue:wlan2g";
> + gpios = <&gpio 14 GPIO_ACTIVE_LOW>;
> + linux,default-trigger = "phy1tpt";
> + };
> + };
> +};
> +
> +ð0 {
> + status = "okay";
> +
> + pll-data = <0x06000000 0x00000101 0x00001616>;
> +
> + phy-mode = "rgmii";
> + phy-handle = <&phy0>;
> +
> + gmac-config {
> + device = <&gmac>;
> + rgmii-gmac0 = <1>;
> + };
> +};
> +
> +&mdio0 {
> + status = "okay";
> +
> + phy0: ethernet-phy at 0 {
> + reg = <0>;
> + phy-mode = "rgmii";
> +
> + qca,ar8327-initvals = <
> + 0x04 0x87a00000 /* PORT0 PAD Mode */
> + 0x0c 0x01000000 /* PORT6 PAD Mode */
> + 0x10 0x80000000 /* PWS_REG_VALUE */
> + 0x7c 0x000000fe /* PORT0_STATUS */
> + 0x94 0x000000fe /* PORT6_STATUS */
> + >;
> + };
> +};
> +
> +&pcie {
> + status = "okay";
> +
> + wifi at 0,0 {
> + compatible = "qcom,ath10k";
> + reg = <0x0000 0 0 0 0>;
> + };
> +};
> +
> +&ref {
> + clock-frequency = <25000000>;
> +};
> +
> +&spi {
> + num-cs = <1>;
> + status = "okay";
> +
> + flash at 0 {
> + compatible = "jedec,spi-nor";
> + reg = <0>;
> + spi-max-frequency = <25000000>;
> +
> + partitions {
> + compatible = "fixed-partitions";
> + #address-cells = <1>;
> + #size-cells = <1>;
> +
> + partition at 0 {
> + label = "u-boot";
> + reg = <0x000000 0x030000>;
> + read-only;
> + };
> +
> + uenv: partition at 30000 {
> + label = "u-boot-env";
> + reg = <0x030000 0x010000>;
> + read-only;
> + };
> +
> + partition at 40000 {
> + compatible = "denx,uimage";
> + label = "firmware";
> + reg = <0x040000 0x750000>;
> + };
> +
> + partition at 790000 {
> + label = "backup";
> + reg = <0x790000 0x010000>;
> + read-only;
> + };
> +
> + partition at 7a0000 {
> + label = "storage";
> + reg = <0x7a0000 0x050000>;
> + read-only;
> + };
> +
> + art: partition at 7f0000 {
> + label = "art";
> + reg = <0x7f0000 0x010000>;
> + read-only;
> + };
> + };
> + };
> +};
> +
> +&uart {
> + status = "okay";
> +};
> +
> +&usb {
> + status = "okay";
> +};
> +
> +&usb_phy {
> + status = "okay";
> +};
> +
> +&wmac {
> + status = "okay";
> +
> + qca,no-eeprom;
> +};
> diff --git a/target/linux/ath79/image/generic.mk
> b/target/linux/ath79/image/generic.mk
> index 55053be34f11..550f24f45c8b 100644
> --- a/target/linux/ath79/image/generic.mk
> +++ b/target/linux/ath79/image/generic.mk
> @@ -674,6 +674,18 @@ define Device/rosinson_wr818 endef
> TARGET_DEVICES += rosinson_wr818
>
> +define Device/sitecom_wlr-7100
> + ATH_SOC := ar1022
> + DEVICE_TITLE := Sitecom WLR-7100 v1 002
> + DEVICE_PACKAGES := ath10k-firmware-qca988x-ct
> +kmod-ath10k-ct-smallbuffers kmod-usb2
> + IMAGES += factory.dlf
> + IMAGE/factory.dlf := append-kernel | pad-to $$$$(BLOCKSIZE) | \
> + append-rootfs | pad-rootfs | check-size $$$$(IMAGE_SIZE) | \
> + senao-header -r 0x222 -p 0x53 -t 2
> + IMAGE_SIZE := 7488k
> +endef
> +TARGET_DEVICES += sitecom_wlr-7100
> +
> define Device/wd_mynet-n750
> $(Device/seama)
> ATH_SOC := ar9344
> --
> 2.26.2
>
>
> _______________________________________________
> openwrt-devel mailing list
> openwrt-devel at lists.openwrt.org
> https://lists.openwrt.org/mailman/listinfo/openwrt-devel
-------------- next part --------------
A non-text attachment was scrubbed...
Name: openpgp-digital-signature.asc
Type: application/pgp-signature
Size: 834 bytes
Desc: not available
URL: <http://lists.infradead.org/pipermail/openwrt-devel/attachments/20200504/fd8d272f/attachment.sig>
-------------- next part --------------
_______________________________________________
openwrt-devel mailing list
openwrt-devel at lists.openwrt.org
https://lists.openwrt.org/mailman/listinfo/openwrt-devel
More information about the openwrt-devel
mailing list