[OpenWrt-Devel] 19.07.0 boot hang on Mikrotik device
mail at adrianschmutzler.de
mail at adrianschmutzler.de
Sun Jan 26 18:35:10 EST 2020
Hi,
> -----Original Message-----
> From: openwrt-devel [mailto:openwrt-devel-bounces at lists.openwrt.org]
> On Behalf Of Baptiste Jonglez
> Sent: Montag, 27. Januar 2020 00:10
> To: Joe Ayers <joe at ayerscasa.com>
> Cc: openwrt-devel at lists.openwrt.org
> Subject: Re: [OpenWrt-Devel] 19.07.0 boot hang on Mikrotik device
>
> Hi,
>
> You should report this bug under "openwrt-19.07":
> https://bugs.openwrt.org/
>
> You are apparently using ar71xx, did you try an ath79 19.07 image?
the first mikrotik device in ath79 was merged to master last week, so ath79 is not an option here ATM.
Best
Adrian
>
> Regards,
> Baptiste
>
> On 25-01-20, Joe Ayers wrote:
> > At http:\\arednmesh.org, we've had several mikrotik devices working,
> > all with "LHG" motherboards. One of the devices, RB LHG 2nD-XL no
> > longer boots with upgrade from 18.06.2 to 19.07.0. Other devices with
> > same "LHG" mother board continue to work fine, e.g. RB LHG 5nD-XL, LHG
> > 5nDHP.
> >
> > I'm stuck on getting this working, if you have any pointers, please
> > let me know. Here's dmesg where it hangs:
> >
> > [ 0.000000] Linux version 4.14.162 (joe at AE6XE-VM) (gcc version
> > 7.5.0 (OpenWrt GCC 7.5.0 r10860-a3ffeb413b)) #0 Mon Jan 6 16:47:09
> > 2020
> > [ 0.000000] bootconsole [early0] enabled
> > [ 0.000000] CPU0 revision is: 00019374 (MIPS 24Kc)
> > [ 0.000000] SoC: Qualcomm Atheros QCA9533 ver 2 rev 0
> > [ 0.000000] Determined physical RAM map:
> > [ 0.000000] memory: 04000000 @ 00000000 (usable)
> > [ 0.000000] User-defined physical RAM map:
> > [ 0.000000] memory: 04000000 @ 00000000 (usable)
> > [ 0.000000] Initrd not found or empty - disabling initrd
> > [ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
> > [ 0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases,
> > linesize 32 bytes
> > [ 0.000000] Zone ranges:
> > [ 0.000000] Normal [mem 0x0000000000000000-0x0000000003ffffff]
> > [ 0.000000] Movable zone start for each node
> > [ 0.000000] Early memory node ranges
> > [ 0.000000] node 0: [mem 0x0000000000000000-0x0000000003ffffff]
> > [ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-
> 0x0000000003ffffff]
> > [ 0.000000] random: get_random_bytes called from 0x80477740 with
> crng_init=0
> > [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 16256
> > [ 0.000000] Kernel command line: no-uart no-buzzer no-nand parts=1
> > boot_part_size=16777216 gpio=0 HZ=325000000 mem=64M
> > kmac=B8:69:F4:79:52:22 board=lhg-hb board=lhg-hb ver=6.42
> > hw_opt=00284001 boot=1 mlc=11 console=ttyS0,115200
> rootfstype=squashfs
> > noinitrd
> > [ 0.000000] PID hash table entries: 256 (order: -2, 1024 bytes)
> > [ 0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
> > [ 0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
> > [ 0.000000] Writing ErrCtl register=00000000
> > [ 0.000000] Readback ErrCtl register=00000000
> > [ 0.000000] Memory: 59928K/65536K available (3634K kernel code,
> > 162K rwdata, 384K rodata, 228K init, 198K bss, 5608K reserved, 0K
> > cma-reserved)
> > [ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1,
> Nodes=1
> > [ 0.000000] NR_IRQS: 51
> > [ 0.000000] Clocks: CPU:650.000MHz, DDR:600.000MHz, AHB:300.000MHz,
> > Ref:25.000MHz
> > [ 0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles:
> > 0xffffffff, max_idle_ns: 5880801374 ns
> > [ 0.000009] sched_clock: 32 bits at 325MHz, resolution 3ns, wraps
> > every 6607641598ns
> > [ 0.008858] Calibrating delay loop... 432.53 BogoMIPS (lpj=2162688)
> > [ 0.075986] pid_max: default: 32768 minimum: 301
> > [ 0.081432] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
> > [ 0.088943] Mountpoint-cache hash table entries: 1024 (order: 0, 4096
> bytes)
> > [ 0.099268] clocksource: jiffies: mask: 0xffffffff max_cycles:
> > 0xffffffff, max_idle_ns: 19112604462750000 ns
> > [ 0.110476] futex hash table entries: 256 (order: -1, 3072 bytes)
> > [ 0.117873] NET: Registered protocol family 16
> > [ 0.126436] MIPS: machine is MikroTik RouterBOARD LHG 2nD-XL
> > [ 0.133043] ar71xx: invalid MDIO id 1
> > [ 0.385180] clocksource: Switched to clocksource MIPS
> > [ 0.391886] NET: Registered protocol family 2
> > [ 0.397634] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
> > [ 0.405608] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
> > [ 0.412831] TCP: Hash tables configured (established 1024 bind 1024)
> > [ 0.420200] UDP hash table entries: 256 (order: 0, 4096 bytes)
> > [ 0.426879] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
> > [ 0.434266] NET: Registered protocol family 1
> > [ 0.444824] workingset: timestamp_bits=30 max_order=14
> bucket_order=0
> > [ 0.457143] squashfs: version 4.0 (2009/01/31) Phillip Lougher
> > [ 0.463756] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME)
> > (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
> > [ 0.484675] io scheduler noop registered
> > [ 0.489176] io scheduler deadline registered (default)
> > [ 0.495371] Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled
> > [ 0.502913] console [ttyS0] disabled
> > [ 0.527117] serial8250.0: ttyS0 at MMIO 0x18020000 (irq = 11,
> > base_baud = 1562500) is a 16550A
> > [ 0.536918] console [ttyS0] enabled
> > [ 0.536918] console [ttyS0] enabled
> > [ 0.544460] bootconsole [early0] disabled
> > [ 0.544460] bootconsole [early0] disabled
> > [ 0.556787] m25p80 spi0.0: found w25q128jv, expected m25p80
> > [ 0.572223] m25p80 spi0.0: w25q128jv (16384 Kbytes)
> > [ 0.577745] Creating 6 MTD partitions on "spi0.0":
> > [ 0.582708] 0x000000000000-0x00000000e000 : "routerboot"
> > [ 0.589854] 0x00000000e000-0x00000000f000 : "hard_config"
> > [ 0.596836] 0x00000000f000-0x000000010000 : "bios"
> > [ 0.603684] 0x000000010000-0x00000001f000 : "routerboot2"
> > [ 0.610655] 0x00000001f000-0x000000020000 : "soft_config"
> > [ 0.618205] 0x000000020000-0x000001000000 : "firmware"
> > [ 0.624569] 2 minor-fw partitions found on MTD device firmware
> > [ 0.630670] 0x000000020000-0x000000190000 : "kernel"
> > [ 0.636507] 0x000000190000-0x000001000000 : "rootfs"
> > [ 0.642258] mtd: device 7 (rootfs) set to be root filesystem
> > [ 0.648186] 1 squashfs-split partitions found on MTD device rootfs
> > [ 0.654578] 0x0000006f0000-0x000001000000 : "rootfs_data"
> > [ 0.664200] libphy: Fixed MDIO Bus: probed
> > [ 0.690987] libphy: ag71xx_mdio: probed
> > [ 1.327500] ag71xx-mdio.1: Found an AR934X built-in switch
> > [ 1.380907] eth0: Atheros AG71xx at 0xba000000, irq 5, mode: gmii
> > [ 1.388695] NET: Registered protocol family 17
> > [ 1.393352] 8021q: 802.1Q VLAN Support v1.8
> > [ 1.410019] VFS: Mounted root (squashfs filesystem) readonly on device
> 31:7.
> > [ 1.418636] Freeing unused kernel memory: 228K
> > [ 1.423222] This architecture does not have kernel memory protection.
> > [ 2.026942] init: Console is alive
> > [ 2.030709] init: - watchdog -
> > [ 2.445217] random: fast init done
> > [ 3.102742] kmodloader: loading kernel modules from /etc/modules-
> boot.d/*
> > [ 3.154160] usbcore: registered new interface driver usbfs
> > [ 3.159975] usbcore: registered new interface driver hub
> > [ 3.165584] usbcore: registered new device driver usb
> > [ 3.176012] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
> > [ 3.183571] kmodloader: done loading kernel modules from
> > /etc/modules-boot.d/*
> > [ 3.193344] init: - preinit -
> > [ 3.630728] random: procd: uninitialized urandom read (4 bytes read)
> > Press the [f] key and hit [enter] to enter failsafe mode Press the
> > [1], [2], [3] or [4] key and hit [enter] to select the debug level
> > [ 6.266613] eth0: link up (1000Mbps/Full duplex)
> >
> > It hangs at this point. What should occur, but does not (from 18.06.2):
> >
> > [ 7.632244] jffs2: notice: (354) jffs2_build_xattr_subsystem:
> > complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan)
> > and 0 of xref (0 dead, 0 orphan) found.
> > [ 7.649615] mount_root: switching to jffs2 overlay
> > [ 7.687438] urandom-seed: Seeding with /etc/urandom.seed
> > [ 7.841353] eth0: link down
> > [ 7.855127] procd: - early -
> > [ 7.858915] procd: - watchdog -
> > [ 8.436062] procd: - watchdog -
> > [ 8.440039] procd: - ubus -
> > [ 8.632931] random: ubusd: uninitialized urandom read (4 bytes read)
> > [ 8.643930] random: ubusd: uninitialized urandom read (4 bytes read)
> > [ 8.651001] random: ubusd: uninitialized urandom read (4 bytes read)
> > [ 8.658593] procd: - init -
> > Please press Enter to activate this console.
> > [ 9.049497] kmodloader: loading kernel modules from /etc/modules.d/*
> > [ 9.061251] ipip: IPv4 and MPLS over IPv4 tunneling driver
> > [ 9.089565] Loading modules backported from Linux version
> > wt-2017-11-01-0-gfe248fc2c180
> > [ 9.097904] Backport generated by backports.git v4.14-rc2-1-31-g86cf0e5d
> > [ 9.119572] nf_conntrack version 0.5.0 (1024 buckets, 4096 max)
> > [ 9.293129] xt_time: kernel timezone is -0000
> > [ 9.447984] ip_tables: (C) 2000-2006 Netfilter Core Team
> > [ 9.629677] ieee80211 phy0: Atheros AR9531 Rev:2 mem=0xb8100000,
> irq=47
> > [ 9.722604] kmodloader: done loading kernel modules from
> /etc/modules.d/*
> > [ 10.709017] urandom_read: 5 callbacks suppressed
> > [ 10.709024] random: jshn: uninitialized urandom read (4 bytes read)
> > [ 17.996749] br-lan: port 1(eth0) entered blocking state
> > [ 18.002220] br-lan: port 1(eth0) entered disabled state
> > [ 18.007947] device eth0 entered promiscuous mode
> > [ 19.628494] eth0: link up (1000Mbps/Full duplex)
> > [ 19.633311] br-lan: port 1(eth0) entered blocking state
> > [ 19.638743] br-lan: port 1(eth0) entered forwarding state
> > [ 25.137046] wlan0: Trigger new scan to find an IBSS to join
> > [ 29.136992] wlan0: Trigger new scan to find an IBSS to join
> > [ 29.177032] wlan0: Creating new IBSS network, BSSID 0a:9e:06:dd:57:f0
> > [ 73.657038] random: crng init done
> >
> > _______________________________________________
> > openwrt-devel mailing list
> > openwrt-devel at lists.openwrt.org
> > https://lists.openwrt.org/mailman/listinfo/openwrt-devel
-------------- next part --------------
A non-text attachment was scrubbed...
Name: openpgp-digital-signature.asc
Type: application/pgp-signature
Size: 834 bytes
Desc: not available
URL: <http://lists.infradead.org/pipermail/openwrt-devel/attachments/20200127/a994299b/attachment.sig>
-------------- next part --------------
_______________________________________________
openwrt-devel mailing list
openwrt-devel at lists.openwrt.org
https://lists.openwrt.org/mailman/listinfo/openwrt-devel
More information about the openwrt-devel
mailing list