[OpenWrt-Devel] [PATCH] ramips: add support for GL.iNet microuter-N300
David Bauer
mail at david-bauer.net
Sun Jan 26 17:26:05 EST 2020
The GL.iNet microuter-N300 (internally referred as MT300N-v4) is a
pocket-size travel router. It is essentially identical to the VIXMINI
(internally referred as MT300N-v3) but with double the RAM and
SPI-flash.
Hardware
--------
SoC: MediaTek MT7628NN
RAM: 128M DDR2
FLASH: 16M
LED: Power - WLAN
BTN: Reset
UART: 115200 8N1
TX and RX are labled on the board as pads next to the SoC
Installation via web-interface
------------------------------
1. Visit the web-interface at 192.168.8.1
Note: The ethernet port is by default WAN. So you need to connect to
the router via WiFi
2. Navigate to the Update tab on the left side.
3. Select "Local Update"
4. Upload the OpenWrt sysupgrade image.
Note: Make sure you select not to preserve the configuration.
Installation via U-Boot
-----------------------
1. Hold down the reset button while powering on the device.
Wait for the LED to flash 5 times.
2. Assign yourself a static IPv4 in 192.168.1.0/24
3. Upload the OpenWrt sysupgrade image at 192.168.1.1.
Signed-off-by: David Bauer <mail at david-bauer.net>
---
.../dts/mt7628an_glinet_microuter-n300.dts | 21 ++++
.../ramips/dts/mt7628an_glinet_vixmini.dts | 97 ++--------------
.../mt7628an_glinet_vixmini_microuter.dtsi | 104 ++++++++++++++++++
target/linux/ramips/image/mt76x8.mk | 8 ++
.../mt76x8/base-files/etc/board.d/02_network | 1 +
5 files changed, 141 insertions(+), 90 deletions(-)
create mode 100644 target/linux/ramips/dts/mt7628an_glinet_microuter-n300.dts
create mode 100644 target/linux/ramips/dts/mt7628an_glinet_vixmini_microuter.dtsi
diff --git a/target/linux/ramips/dts/mt7628an_glinet_microuter-n300.dts b/target/linux/ramips/dts/mt7628an_glinet_microuter-n300.dts
new file mode 100644
index 0000000000..742cd6a8ef
--- /dev/null
+++ b/target/linux/ramips/dts/mt7628an_glinet_microuter-n300.dts
@@ -0,0 +1,21 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/dts-v1/;
+
+#include "mt7628an_glinet_vixmini_microuter.dtsi"
+
+/{
+ compatible = "glinet,microuter-n300", "mediatek,mt7628an-soc";
+ model = "GL.iNet microuter-N300";
+};
+
+&led_power_blue {
+ label = "microuter-n300:blue:power";
+};
+
+&led_wlan_white {
+ label = "microuter-n300:white:wlan";
+};
+
+&firmware_part {
+ reg = <0x50000 0xfb0000>;
+};
diff --git a/target/linux/ramips/dts/mt7628an_glinet_vixmini.dts b/target/linux/ramips/dts/mt7628an_glinet_vixmini.dts
index 0935ec869b..9cdd9a0e14 100644
--- a/target/linux/ramips/dts/mt7628an_glinet_vixmini.dts
+++ b/target/linux/ramips/dts/mt7628an_glinet_vixmini.dts
@@ -1,104 +1,21 @@
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
/dts-v1/;
-#include "mt7628an.dtsi"
-
-#include <dt-bindings/gpio/gpio.h>
-#include <dt-bindings/input/input.h>
+#include "mt7628an_glinet_vixmini_microuter.dtsi"
/{
compatible = "glinet,vixmini", "mediatek,mt7628an-soc";
model = "GL.iNet VIXMINI";
-
- aliases {
- led-boot = &led_power;
- led-failsafe = &led_power;
- led-running = &led_power;
- led-upgrade = &led_power;
- };
-
- chosen {
- bootargs = "console=ttyS0,115200";
- };
-
- leds {
- compatible = "gpio-leds";
-
- led_power: power {
- label = "vixmini:blue:power";
- default-state = "on";
- gpios = <&gpio1 10 GPIO_ACTIVE_LOW>;
- };
-
- wlan {
- label = "vixmini:white:wlan";
- gpios = <&gpio1 12 GPIO_ACTIVE_LOW>;
- linux,default-trigger = "phy0tpt";
- };
- };
-
- keys {
- compatible = "gpio-keys";
-
- reset {
- label = "reset";
- gpios = <&gpio1 6 GPIO_ACTIVE_LOW>;
- linux,code = <KEY_RESTART>;
- };
- };
};
-&state_default {
- gpio {
- ralink,group = "wdt", "wled_an", "p1led_an";
- ralink,function = "gpio";
- };
+&led_power_blue {
+ label = "vixmini:blue:power";
};
-ðernet {
- mtd-mac-address = <&factory 0x4>;
+&led_wlan_white {
+ label = "vixmini:white:wlan";
};
-&wmac {
- status = "okay";
-};
-
-&spi0 {
- status = "okay";
-
- flash at 0 {
- compatible = "jedec,spi-nor";
- reg = <0>;
- spi-max-frequency = <10000000>;
-
- partitions {
- compatible = "fixed-partitions";
- #address-cells = <1>;
- #size-cells = <1>;
-
- partition at 0 {
- label = "u-boot";
- reg = <0x0 0x30000>;
- read-only;
- };
-
- partition at 30000 {
- label = "u-boot-env";
- reg = <0x30000 0x10000>;
- read-only;
- };
-
- factory: partition at 40000 {
- label = "factory";
- reg = <0x40000 0x10000>;
- read-only;
- };
-
- partition at 50000 {
- compatible = "denx,uimage";
- label = "firmware";
- reg = <0x50000 0x7b0000>;
- };
- };
- };
+&firmware_part {
+ reg = <0x50000 0x7b0000>;
};
diff --git a/target/linux/ramips/dts/mt7628an_glinet_vixmini_microuter.dtsi b/target/linux/ramips/dts/mt7628an_glinet_vixmini_microuter.dtsi
new file mode 100644
index 0000000000..b5611ac11e
--- /dev/null
+++ b/target/linux/ramips/dts/mt7628an_glinet_vixmini_microuter.dtsi
@@ -0,0 +1,104 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+
+#include "mt7628an.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+
+/{
+ aliases {
+ led-boot = &led_power_blue;
+ led-failsafe = &led_power_blue;
+ led-running = &led_power_blue;
+ led-upgrade = &led_power_blue;
+
+ label-mac-device = ðernet;
+ };
+
+ chosen {
+ bootargs = "console=ttyS0,115200";
+ };
+
+ leds {
+ compatible = "gpio-leds";
+
+ led_power_blue: power {
+ /* Name is set device-specific */
+ gpios = <&gpio1 10 GPIO_ACTIVE_LOW>;
+ };
+
+ led_wlan_white: wlan {
+ /* Name is set device-specific */
+ gpios = <&gpio1 12 GPIO_ACTIVE_LOW>;
+ linux,default-trigger = "phy0tpt";
+ };
+ };
+
+ keys {
+ compatible = "gpio-keys";
+
+ reset {
+ label = "reset";
+ gpios = <&gpio1 6 GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_RESTART>;
+ };
+ };
+};
+
+&state_default {
+ gpio {
+ ralink,group = "wdt", "wled_an", "p1led_an";
+ ralink,function = "gpio";
+ };
+};
+
+ðernet {
+ mtd-mac-address = <&factory 0x4>;
+};
+
+&wmac {
+ status = "okay";
+};
+
+&spi0 {
+ status = "okay";
+
+ flash at 0 {
+ compatible = "jedec,spi-nor";
+ reg = <0>;
+ spi-max-frequency = <10000000>;
+
+ partitions: partitions {
+ compatible = "fixed-partitions";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ partition at 0 {
+ label = "u-boot";
+ reg = <0x0 0x30000>;
+ read-only;
+ };
+
+ partition at 30000 {
+ label = "u-boot-env";
+ reg = <0x30000 0x10000>;
+ read-only;
+ };
+
+ factory: partition at 40000 {
+ label = "factory";
+ reg = <0x40000 0x10000>;
+ read-only;
+ };
+
+ /*
+ * Firmware-partition size is model-specific
+ * due to different flash sizes.
+ */
+ firmware_part: partition at 50000 {
+ compatible = "denx,uimage";
+ label = "firmware";
+ };
+ };
+ };
+};
diff --git a/target/linux/ramips/image/mt76x8.mk b/target/linux/ramips/image/mt76x8.mk
index 5ddeec14d5..37cac84229 100644
--- a/target/linux/ramips/image/mt76x8.mk
+++ b/target/linux/ramips/image/mt76x8.mk
@@ -70,6 +70,14 @@ define Device/glinet_gl-mt300n-v2
endef
TARGET_DEVICES += glinet_gl-mt300n-v2
+define Device/glinet_microuter-n300
+ IMAGE_SIZE := 16064k
+ DEVICE_VENDOR := GL.iNet
+ DEVICE_MODEL := microuter-N300
+ SUPPORTED_DEVICES += microuter-n300
+endef
+TARGET_DEVICES += glinet_microuter-n300
+
define Device/glinet_vixmini
IMAGE_SIZE := 7872k
DEVICE_VENDOR := GL.iNet
diff --git a/target/linux/ramips/mt76x8/base-files/etc/board.d/02_network b/target/linux/ramips/mt76x8/base-files/etc/board.d/02_network
index b036eb76e6..259a257f16 100755
--- a/target/linux/ramips/mt76x8/base-files/etc/board.d/02_network
+++ b/target/linux/ramips/mt76x8/base-files/etc/board.d/02_network
@@ -33,6 +33,7 @@ ramips_setup_interfaces()
ucidef_add_switch "switch0" \
"1:lan" "0:wan" "6 at eth0"
;;
+ glinet,microuter-n300|\
glinet,vixmini)
ucidef_add_switch "switch0" \
"0:lan" "6 at eth0"
--
2.25.0
_______________________________________________
openwrt-devel mailing list
openwrt-devel at lists.openwrt.org
https://lists.openwrt.org/mailman/listinfo/openwrt-devel
More information about the openwrt-devel
mailing list