[OpenWrt-Devel] [PATCH v4 2/2] ath79: add support for Teltonika RUT955
Daniel Golle
daniel at makrotopia.org
Tue Feb 11 13:34:43 EST 2020
Specification:
- 550/400/200 MHz (CPU/DDR/AHB)
- 128 MB of RAM (DDR2)
- 16 MB of FLASH (SPI NOR)
- 4x 10/100 Mbps Ethernet, with passive PoE support on LAN1
- 2T2R 2,4 GHz (AR9344)
- built-in 4G/3G module (example: Quectel EC-25EU)
- internal microSD slot (spi-mmc, buggy and disabled for now)
- RS232 on D-Sub9 port (Cypress ACM via USB, /dev/ttyACM0)
- RS422/RS485 (AR934x high speed UART, /dev/ttyATH1)
- analog 0-24V input (MCP3221)
- various digital inputs and outputs incl. a relay
- 11x LED (4 are driven by AR9344, 7 by 74HC595)
- 2x miniSIM slot (can be swapped via GPIO)
- 2x RP-SMA/F (Wi-Fi), 3x SMA/F (2x WWAN, GPS)
- 1x button (reset)
- DC jack for main power input (9-30 V)
- debugging UART available on PCB edge connector
Serial console (/dev/ttyS0) pinout:
- RX: pin1 (square) on top side of the main PCB (AR9344 is on top)
- TX: pin1 (square) on bottom side
Flash instruction:
Vendor firmware is based on OpenWrt CC release. Use the "factory" image
directly in GUI (make sure to uncheck "keep settings") or in U-Boot web
based recovery. To avoid any problems, make sure to first update vendor
firmware to latest version - "factory" image was successfully tested on
device running "RUT9XX_R_00.06.051" firmware and U-Boot "3.0.2".
Signed-off-by: Daniel Golle <daniel at makrotopia.org>
---
.../ath79/dts/ar9344_teltonika_rut955.dts | 348 ++++++++++++++++++
.../generic/base-files/etc/board.d/02_network | 5 +
.../base-files/etc/board.d/03_gpio_switches | 8 +
target/linux/ath79/image/generic.mk | 38 ++
4 files changed, 399 insertions(+)
create mode 100644 target/linux/ath79/dts/ar9344_teltonika_rut955.dts
diff --git a/target/linux/ath79/dts/ar9344_teltonika_rut955.dts b/target/linux/ath79/dts/ar9344_teltonika_rut955.dts
new file mode 100644
index 0000000000..8efe198673
--- /dev/null
+++ b/target/linux/ath79/dts/ar9344_teltonika_rut955.dts
@@ -0,0 +1,348 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/dts-v1/;
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+
+#include "ar9344.dtsi"
+
+/ {
+ model = "Teltonika RUT955";
+ compatible = "teltonika,rut955", "qca,ar9344";
+
+ aliases {
+ serial0 = &uart;
+ serial1 = &hs_uart;
+ led-boot = &led_system_green;
+ led-failsafe = &led_system_red;
+ led-running = &led_system_green;
+ led-upgrade = &led_system_red;
+ label-mac-device = ð1;
+ };
+
+ i2c {
+ compatible = "i2c-gpio";
+ scl-gpios = <&gpio 16 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>;
+ sda-gpios = <&gpio 17 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ hwmon at 4d {
+ compatible = "microchip,mcp3221";
+ reg = <0x4d>;
+ };
+ };
+
+
+ leds {
+ compatible = "gpio-leds";
+
+ signal1 {
+ label = "rut955:green:signal1";
+ gpios = <&gpio_ext 0 GPIO_ACTIVE_HIGH>;
+ };
+
+ signal2 {
+ label = "rut955:green:signal2";
+ gpios = <&gpio_ext 1 GPIO_ACTIVE_HIGH>;
+ };
+
+ signal3 {
+ label = "rut955:green:signal3";
+ gpios = <&gpio_ext 2 GPIO_ACTIVE_HIGH>;
+ };
+
+ signal4 {
+ label = "rut955:green:signal4";
+ gpios = <&gpio_ext 3 GPIO_ACTIVE_HIGH>;
+ };
+
+ signal5 {
+ label = "rut955:green:signal5";
+ gpios = <&gpio_ext 4 GPIO_ACTIVE_HIGH>;
+ };
+
+ led_system_red: system_red {
+ label = "rut955:red:system";
+ gpios = <&gpio_ext 5 GPIO_ACTIVE_HIGH>;
+ };
+
+ led_system_green: system_green {
+ label = "rut955:green:system";
+ gpios = <&gpio_ext 6 GPIO_ACTIVE_HIGH>;
+ default-state = "on";
+ };
+ };
+
+ keys {
+ compatible = "gpio-keys";
+
+ reset {
+ label = "reset";
+ linux,code = <KEY_RESTART>;
+ gpios = <&gpio 15 GPIO_ACTIVE_LOW>;
+ debounce-interval = <60>;
+ };
+ };
+};
+
+&gpio {
+ pinctrl-names = "default";
+ pinctrl-0 = <&jtag_disable_pins>;
+
+ gpio-line-names = "RS485_D", "wan_led", "DIN3", "mmc_cs",
+ "leds_sck", "", "", "",
+ "", "", "", "",
+ "leds_mosi", "lan2_led", "lan1_led", "",
+ "i2c_scl", "i2c_sda", "", "DIN2",
+ "leds_cs", "DIN1", "lan3_led", "",
+ "", "", "", "",
+ "", "", "", "";
+
+ gpio_leds_sck {
+ gpio-hog;
+ gpios = <4 GPIO_ACTIVE_HIGH>;
+ output-high;
+ line-name = "rut955:leds:sck";
+ };
+
+ gpio_leds_mosi {
+ gpio-hog;
+ gpios = <12 GPIO_ACTIVE_HIGH>;
+ output-high;
+ line-name = "rut955:leds:mosi";
+ };
+
+ gpio_leds_cs {
+ gpio-hog;
+ gpios = <20 GPIO_ACTIVE_HIGH>;
+ output-low;
+ line-name = "rut955:leds:cs";
+ };
+
+ gpio_mmc_cs {
+ gpio-hog;
+ gpios = <3 GPIO_ACTIVE_HIGH>;
+ output-high;
+ line-name = "rut955:mmc:cs";
+ };
+
+ gpio_uart1_td {
+ gpio-hog;
+ gpios = <18 GPIO_ACTIVE_HIGH>;
+ output-high;
+ line-name = "rut955:uart1:td";
+ };
+
+ gpio_uart1_rd {
+ gpio-hog;
+ gpios = <11 GPIO_ACTIVE_LOW>;
+ input;
+ line-name = "rut955:uart1:rd";
+ };
+
+ gpio_switch_wanled {
+ gpio-hog;
+ gpios = <1 GPIO_ACTIVE_HIGH>;
+ output-high;
+ line-name = "rut955:led:wan";
+ };
+
+ gpio_switch_lan2led {
+ gpio-hog;
+ gpios = <13 GPIO_ACTIVE_HIGH>;
+ output-high;
+ line-name = "rut955:led:lan2";
+ };
+
+ gpio_switch_lan1led {
+ gpio-hog;
+ gpios = <14 GPIO_ACTIVE_HIGH>;
+ output-high;
+ line-name = "rut955:led:lan1";
+ };
+
+ gpio_switch_lan3led {
+ gpio-hog;
+ gpios = <22 GPIO_ACTIVE_HIGH>;
+ output-high;
+ line-name = "rut955:led:lan3";
+ };
+};
+
+&ref {
+ clock-frequency = <40000000>;
+};
+
+&uart {
+ status = "okay";
+};
+
+&hs_uart {
+ status = "okay";
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&pmx_uart2>;
+
+ rts-gpios = <&gpio 0 GPIO_ACTIVE_HIGH>;
+ rs485-rts-active-low;
+ linux,rs485-enabled-at-boot-time;
+};
+
+&spi {
+ status = "okay";
+
+ num-cs = <3>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pmx_spi>;
+
+ flash at 0 {
+ compatible = "jedec,spi-nor";
+ reg = <0>;
+ spi-max-frequency = <25000000>;
+
+ partitions {
+ compatible = "fixed-partitions";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ partition at 0 {
+ label = "u-boot";
+ reg = <0x0 0x20000>;
+ read-only;
+ };
+
+ config: partition at 20000 {
+ label = "config";
+ reg = <0x20000 0x10000>;
+ read-only;
+ };
+
+ art: partition at 30000 {
+ label = "art";
+ reg = <0x30000 0x10000>;
+ read-only;
+ };
+
+ partition at 40000 {
+ label = "firmware";
+ reg = <0x40000 0xf30000>;
+ compatible = "tplink,firmware";
+ };
+
+ partition at f70000 {
+ label = "event-log";
+ reg = <0xf70000 0x90000>;
+ read-only;
+ };
+ };
+ };
+
+ microsd at 1 {
+ status = "disabled";
+
+ compatible = "mmc-spi-slot";
+ spi-max-frequency = <25000000>;
+ reg = <1>;
+ voltage-ranges = <3200 3400>;
+ broken-cd;
+ };
+
+ gpio_ext: gpio_ext at 2 {
+ compatible = "fairchild,74hc595";
+ reg = <2>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ registers-number = <2>;
+ spi-max-frequency = <10000000>;
+ gpio-line-names = "led_signal_bar1", "led_signal_bar2", "led_signal_bar3", "led_signal_bar4",
+ "led_signal_bar5", "led_status_red", "led_status_green", "sim_sel",
+ "DOUT1", "DOUT2", "modem_vbus", "modem_rst",
+ "DOUT3", "RS485_R", "SDCS", "HWRST";
+ };
+};
+
+&usb {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "okay";
+
+ port at 1 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <1>;
+
+ port at 1 {
+ compatible = "usb-a-connector";
+ label = "USB2.0 port";
+ reg = <1>;
+ };
+
+ port at 3 {
+ label = "internal Cypress CDC-ACM serial";
+ reg = <3>;
+ };
+
+ port at 4 {
+ label = "internal Quectel EC-25 modem";
+ reg = <4>;
+ };
+ };
+};
+
+&usb_phy {
+ status = "okay";
+};
+
+&wmac {
+ status = "okay";
+
+ mtd-cal-data = <&art 0x1000>;
+ mtd-mac-address = <&config 0x0>;
+ mtd-mac-address-increment = <2>;
+};
+
+ð0 {
+ status = "okay";
+
+ phy-handle = <&swphy4>;
+
+ mtd-mac-address = <&config 0x0>;
+ mtd-mac-address-increment = <1>;
+};
+
+ð1 {
+ status = "okay";
+
+ mtd-mac-address = <&config 0x0>;
+};
+
+&builtin_switch {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pmx_leds_switch>;
+};
+
+&pinmux {
+ pmx_spi: pinmux_spi {
+ // SPI_CS1 on GPIO 3, 2nd SCK on GPIO 4
+ // 2nd MOSI on GPIO 12, SPI_CS2 on GPIO 20
+ pinctrl-single,bits = <0x0 0x07000000 0xff000000>,
+ <0x4 0x0a 0xff>,
+ <0xc 0x0b 0xff>,
+ <0x14 0x08 0xff>;
+ };
+
+ pmx_leds_switch: pinmux_leds_switch {
+ // switch port LEDs on GPIO 1, GPIO 13, GPIO 14 and GPIO 22
+ pinctrl-single,bits = <0x0 0x00002d00 0x0000ff00>,
+ <0xc 0x002c2b00 0x00ffff00>,
+ <0x14 0x002a0000 0x00ff0000>;
+ };
+
+ pmx_uart2: pinmux_uart2 {
+ // UART1_DTR on GPIO 0, UART1_RD on GPIO 11, UART1_TD on GPIO 18
+ pinctrl-single,bits = <0x0 0x0 0xff>,
+ <0x10 0x4f000000 0xff000000>,
+ <0x3c 0x000b0000 0x00ff0000>;
+ };
+};
diff --git a/target/linux/ath79/generic/base-files/etc/board.d/02_network b/target/linux/ath79/generic/base-files/etc/board.d/02_network
index a3fcf35715..6ba782f89b 100755
--- a/target/linux/ath79/generic/base-files/etc/board.d/02_network
+++ b/target/linux/ath79/generic/base-files/etc/board.d/02_network
@@ -217,6 +217,11 @@ ath79_setup_interfaces()
ucidef_add_switch "switch0" \
"0 at eth0" "1:lan" "2:lan" "3:wan"
;;
+ teltonika,rut955)
+ ucidef_set_interface_wan "eth1"
+ ucidef_add_switch "switch0" \
+ "0 at eth0" "2:lan:3" "3:lan:2" "4:lan:1"
+ ;;
tplink,archer-a7-v5|\
tplink,archer-c6-v2|\
tplink,archer-c6-v2-us|\
diff --git a/target/linux/ath79/generic/base-files/etc/board.d/03_gpio_switches b/target/linux/ath79/generic/base-files/etc/board.d/03_gpio_switches
index 967e2c7680..b5b46f16bf 100755
--- a/target/linux/ath79/generic/base-files/etc/board.d/03_gpio_switches
+++ b/target/linux/ath79/generic/base-files/etc/board.d/03_gpio_switches
@@ -38,6 +38,14 @@ dlink,dir-835-a1)
librerouter,librerouter-v1)
ucidef_add_gpio_switch "poe_passthrough" "PoE Passthrough" "1" "0"
;;
+teltonika,rut955)
+ ucidef_add_gpio_switch "sim_sel" "SIM select" "503" "1"
+ ucidef_add_gpio_switch "DOUT1" "DOUT1 (OC)" "504" "0"
+ ucidef_add_gpio_switch "DOUT2" "DOUT2 (Relay)" "505" "0"
+ ucidef_add_gpio_switch "modem_vbus" "Modem enable" "506" "1"
+ ucidef_add_gpio_switch "modem_rst" "Modem reset" "507" "0"
+ ucidef_add_gpio_switch "DOUT3" "DOUT3" "508" "0"
+ ;;
tplink,archer-c25-v1)
ucidef_add_gpio_switch "led_control" "LED control" "21" "0"
ucidef_add_gpio_switch "led_reset" "LED reset" "19" "1"
diff --git a/target/linux/ath79/image/generic.mk b/target/linux/ath79/image/generic.mk
index 3c74b0f7d7..3447871385 100644
--- a/target/linux/ath79/image/generic.mk
+++ b/target/linux/ath79/image/generic.mk
@@ -36,6 +36,11 @@ define Build/addpattern
-mv "$@.new" "$@"
endef
+define Build/append-md5sum-bin
+ $(STAGING_DIR_HOST)/bin/mkhash md5 $@ | sed 's/../\\\\x&/g' |\
+ xargs echo -ne >> $@
+endef
+
define Build/cybertan-trx
@echo -n '' > $@-empty.bin
-$(STAGING_DIR_HOST)/bin/trx -o $@.new \
@@ -73,6 +78,17 @@ define Build/pisen_wmb001n-factory
rm -rf "$@.tmp"
endef
+define Build/teltonika-fw-fake-checksum
+ # Teltonika U-Boot web based firmware upgrade/recovery routine compares
+ # 16 bytes from md5sum1[16] field in TP-Link v1 header (offset: 76 bytes
+ # from begin of the firmware file) with 16 bytes stored just before
+ # 0xdeadc0de marker. Values are only compared, MD5 sum is not verified.
+ let \
+ offs="$$(stat -c%s $@) - 20"; \
+ dd if=$@ bs=1 count=16 skip=76 |\
+ dd of=$@ bs=1 count=16 seek=$$offs conv=notrunc
+endef
+
define Device/seama
KERNEL := kernel-bin | append-dtb | relocate-kernel | lzma
KERNEL_INITRAMFS := $$(KERNEL) | seama
@@ -1054,6 +1070,28 @@ define Device/sitecom_wlr-7100
endef
TARGET_DEVICES += sitecom_wlr-7100
+define Device/teltonika_rut955
+ SOC := ar9344
+ DEVICE_VENDOR := Teltonika
+ DEVICE_MODEL := RUT955
+ DEVICE_PACKAGES := kmod-usb2 kmod-usb-acm kmod-usb-net-qmi-wwan \
+ kmod-usb-serial-option kmod-hwmon-mcp3021 uqmi -uboot-envtools
+ IMAGE_SIZE := 15552k
+ TPLINK_HWID := 0x35000001
+ TPLINK_HWREV := 0x1
+ TPLINK_HEADER_VERSION := 1
+ KERNEL := kernel-bin | append-dtb | lzma | tplink-v1-header
+ KERNEL_INITRAMFS := kernel-bin | append-dtb | lzma | uImage lzma
+ IMAGES += factory.bin
+ IMAGE/factory.bin := append-kernel | pad-to $$$$(BLOCKSIZE) | append-rootfs |\
+ pad-rootfs | teltonika-fw-fake-checksum | append-string master |\
+ append-md5sum-bin | check-size $$$$(IMAGE_SIZE)
+ IMAGE/sysupgrade.bin := append-kernel | pad-to $$$$(BLOCKSIZE) |\
+ append-rootfs | pad-rootfs | append-metadata |\
+ check-size $$$$(IMAGE_SIZE)
+endef
+TARGET_DEVICES += teltonika_rut955
+
define Device/trendnet_tew-823dru
SOC := qca9558
DEVICE_VENDOR := Trendnet
--
2.25.0
_______________________________________________
openwrt-devel mailing list
openwrt-devel at lists.openwrt.org
https://lists.openwrt.org/mailman/listinfo/openwrt-devel
More information about the openwrt-devel
mailing list