[OpenWrt-Devel] [PATCH v4] mvebu: add support for Buffalo LinkStation LS421DE
Daniel Gonzalez Cabanelas
dgcbueu at gmail.com
Tue Apr 7 08:35:26 EDT 2020
Buffalo LinkStation LS421DE is a dual bay NAS, based on Marvell Armada 370
Hardware:
SoC: Marvell Armada 88F6707-A1
CPU: Cortex-A9 1200 MHz, 1 core
Flash: SPI-NOR 1 MiB, NAND 512 MiB
RAM: DDR3 512 MiB
Ethernet: 1x 10/100/1000 Mbps
USB: 1x 2.0, 1x 3.0
SATA: 2x 3.0 Gbps
LEDs/Input : 5x / 2x (1x button, 1x slide-switch)
RTC: Ricoh RS5C372A, I2C, no battery
Flash instruction (UART+TFTP):
1. Downgrade the OEM firmware to 1.34 version (BUFFALO_BOOTVER=0.13)
2. Remove any hard drive from inside the bays.
3. Boot the Openwrt initramfs image using the U-Boot serial console:
tftpboot 0x1200000 buffalo_ls421de-initramfs-kernel.bin
bootm 0x1200000
4. Flash the sysupgrade image using the Openwrt console:
sysupgrade -n buffalo_ls421de-squashfs-sysupgrade.bin
5. Wait until it finish, the device will reboot with Openwrt installed
on the NAND flash.
Note:
- Device shuting down doesn't work, even if the power slide switch is
used. We must first, via MDIO, set the unused LED2 at the ethernet
phy0 to off state. Reboot works ok.
Signed-off-by: Daniel González Cabanelas <dgcbueu at gmail.com>
Reviewed-by: Tomasz Maciej Nowak <tomek_n at o2.pl>
---
Changes in v2:
- dts file tuned
- Adjusted the i2c bus speed to the max supported by the RTC
- Deleted unneded kernel patch
- Image creation: only included neccesary packages, delete the ubinize
parameter
Changes in v3:
- dts file tuned
- Adjusted the i2c bus speed to the max supported by the SoC
- Added vdd cpu power down pinmux
- Image creation: adjusted the packages required by this device.
Deleted redundant parameters.
- Fixed installation instructions
Changes in v4:
- Commit log: Added reviewer info
.../base-files/lib/preinit/06_set_iface_mac | 4 +
.../base-files/lib/upgrade/platform.sh | 3 +
.../boot/dts/armada-370-buffalo-ls421de.dts | 360 ++++++++++++++++++
target/linux/mvebu/image/Makefile | 14 +
target/linux/mvebu/image/cortexa9.mk | 16 +
5 files changed, 397 insertions(+)
create mode 100644 target/linux/mvebu/files-4.19/arch/arm/boot/dts/armada-370-buffalo-ls421de.dts
diff --git a/target/linux/mvebu/cortexa9/base-files/lib/preinit/06_set_iface_mac b/target/linux/mvebu/cortexa9/base-files/lib/preinit/06_set_iface_mac
index fd41836c8d..62ce2653a0 100644
--- a/target/linux/mvebu/cortexa9/base-files/lib/preinit/06_set_iface_mac
+++ b/target/linux/mvebu/cortexa9/base-files/lib/preinit/06_set_iface_mac
@@ -9,6 +9,10 @@ preinit_set_mac_address() {
. /lib/functions.sh
case $(board_name) in
+ buffalo,ls421de)
+ mac=$(mtd_get_mac_ascii u-boot-env eth1addr)
+ ip link set dev eth0 address $mac 2>/dev/null
+ ;;
linksys,caiman|linksys,cobra|linksys,rango|linksys,shelby|linksys,venom)
# rename interfaces back to the way they were with 4.4
case "$(readlink /sys/class/net/eth0)" in
diff --git a/target/linux/mvebu/cortexa9/base-files/lib/upgrade/platform.sh b/target/linux/mvebu/cortexa9/base-files/lib/upgrade/platform.sh
index 8baed969a3..63042b1535 100755
--- a/target/linux/mvebu/cortexa9/base-files/lib/upgrade/platform.sh
+++ b/target/linux/mvebu/cortexa9/base-files/lib/upgrade/platform.sh
@@ -22,6 +22,9 @@ platform_check_image() {
platform_do_upgrade() {
case "$(board_name)" in
+ buffalo,ls421de)
+ nand_do_upgrade "$1"
+ ;;
cznic,turris-omnia|\
solidrun,clearfog-base-a1|\
solidrun,clearfog-pro-a1)
diff --git a/target/linux/mvebu/files-4.19/arch/arm/boot/dts/armada-370-buffalo-ls421de.dts b/target/linux/mvebu/files-4.19/arch/arm/boot/dts/armada-370-buffalo-ls421de.dts
new file mode 100644
index 0000000000..6b8a964ab3
--- /dev/null
+++ b/target/linux/mvebu/files-4.19/arch/arm/boot/dts/armada-370-buffalo-ls421de.dts
@@ -0,0 +1,360 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Device Tree file for Buffalo LinkStation LS421DE
+ *
+ * Copyright (C) 2020 Daniel González Cabanelas <dgcbueu at gmail.com>
+ */
+
+/dts-v1/;
+
+#include "armada-370.dtsi"
+#include "mvebu-linkstation-fan.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+
+/ {
+ model = "Buffalo LinkStation LS421DE";
+ compatible = "buffalo,ls421de", "marvell,armada370", "marvell,armada-370-xp";
+
+ aliases {
+ led-boot = &led_boot;
+ led-failsafe = &led_failsafe;
+ led-running = &led_power;
+ led-upgrade = &led_upgrade;
+ };
+
+ chosen {
+ bootargs = "console=ttyS0,115200 earlyprintk noinitrd rootfstype=squashfs";
+ stdout-path = "serial0:115200n8";
+ append-rootblock = "nullparameter="; /* override the bootloader args */
+ };
+
+ memory {
+ device_type = "memory";
+ reg = <0x00000000 0x20000000>; /* 512 MB */
+ };
+
+ soc {
+ ranges = <MBUS_ID(0xf0, 0x01) 0 0xd0000000 0x100000
+ MBUS_ID(0x01, 0xe0) 0 0xfff00000 0x100000
+ MBUS_ID(0x09, 0x01) 0 0xf1100000 0x10000>;
+ };
+
+ gpio_fan {
+ gpios = <&gpio0 13 GPIO_ACTIVE_HIGH
+ &gpio0 14 GPIO_ACTIVE_HIGH>;
+ alarm-gpios = <&gpio0 10 GPIO_ACTIVE_HIGH>;
+ };
+
+ gpio_keys {
+ compatible = "gpio-keys";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ pinctrl-0 = <&pmx_hdd_present &pmx_buttons>;
+ pinctrl-names = "default";
+
+ hdd1-present {
+ label = "HDD1 Present";
+ linux,code = <KEY_PROG1>;
+ gpios = <&gpio0 11 GPIO_ACTIVE_LOW>;
+ };
+
+ hdd2-present {
+ label = "HDD2 Present";
+ linux,code = <KEY_PROG2>;
+ gpios = <&gpio0 12 GPIO_ACTIVE_LOW>;
+
+ };
+
+ power {
+ label = "Power Switch";
+ linux,code = <KEY_POWER>;
+ linux,input-type = <EV_SW>;
+ gpios = <&gpio0 15 GPIO_ACTIVE_LOW>;
+ };
+
+ function {
+ label = "Function Button";
+ linux,code = <KEY_OPTION>;
+ gpios = <&gpio0 16 GPIO_ACTIVE_LOW>;
+ };
+ };
+
+ gpio_leds {
+ compatible = "gpio-leds";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pmx_leds1 &pmx_leds2>;
+
+ system_red {
+ label = "ls421de:red:system";
+ gpios = <&gpio0 7 GPIO_ACTIVE_HIGH>;
+ };
+
+ led_power: power_white {
+ label = "ls421de:white:power";
+ gpios = <&gpio1 22 GPIO_ACTIVE_HIGH>;
+ default-state = "on";
+ };
+
+ led_failsafe: power_red {
+ label = "ls421de:red:power";
+ gpios = <&gpio1 23 GPIO_ACTIVE_HIGH>;
+ };
+
+ led_upgrade: power_orange {
+ label = "ls421de:orange:power";
+ gpios = <&gpio1 25 GPIO_ACTIVE_HIGH>;
+ };
+
+ led_boot: system_white {
+ label = "ls421de:white:system";
+ gpios = <&gpio1 27 GPIO_ACTIVE_HIGH>;
+ };
+
+ hdd1_red {
+ label = "ls421de:red:hdd1";
+ gpios = <&gpio1 29 GPIO_ACTIVE_HIGH>;
+ default-state = "off";
+ linux,default-trigger = "disk-activity";
+ };
+
+ hdd2_red {
+ label = "ls421de:red:hdd2";
+ gpios = <&gpio1 30 GPIO_ACTIVE_HIGH>;
+ default-state = "off";
+ linux,default-trigger = "disk-activity";
+ };
+ };
+
+ regulators {
+ compatible = "simple-bus";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ pinctrl-0 = <&pmx_power_usb &pmx_power_hdd1 &pmx_power_hdd2>;
+
+ pinctrl-names = "default";
+
+ usb_v5_regulator: usb-v5-regulator {
+ compatible = "regulator-fixed";
+ regulator-name = "USB";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ enable-active-high;
+ regulator-always-on;
+ regulator-boot-on;
+ gpio = <&gpio0 5 GPIO_ACTIVE_HIGH>;
+ };
+
+ ata1_regulator: ata1-regulator {
+ compatible = "regulator-fixed";
+ reg = <1>;
+ regulator-name = "HDD1";
+ regulator-min-microvolt = <12000000>;
+ regulator-max-microvolt = <12000000>;
+ startup-delay-us = <2000000>;
+ enable-active-high;
+ regulator-always-on;
+ regulator-boot-on;
+ gpio = <&gpio0 8 GPIO_ACTIVE_HIGH>;
+ };
+
+ ata2_regulator: ata2-regulator {
+ compatible = "regulator-fixed";
+ reg = <2>;
+ regulator-name = "HDD2";
+ regulator-min-microvolt = <12000000>;
+ regulator-max-microvolt = <12000000>;
+ startup-delay-us = <4000000>;
+ enable-active-high;
+ regulator-always-on;
+ regulator-boot-on;
+ gpio = <&gpio0 9 GPIO_ACTIVE_HIGH>;
+ };
+ };
+
+ /* FIXME: this driver needs to be aware of the LED2 eth phy use,
+ which must be set to off state before shutting down the machine */
+ restart_poweroff {
+ compatible = "restart-poweroff";
+ };
+};
+
+ð1 {
+ pinctrl-0 = <&ge1_rgmii_pins>;
+ pinctrl-names = "default";
+ status = "okay";
+ phy = <&phy0>;
+ phy-mode = "rgmii-id";
+};
+
+&i2c0 {
+ clock-frequency = <100000>;
+ status = "okay";
+
+ rs5c372a: rs5c372a at 32 {
+ compatible = "ricoh,rs5c372a";
+ reg = <0x32>;
+ };
+};
+
+&mdio {
+ pinctrl-0 = <&mdio_pins>;
+ pinctrl-names = "default";
+
+ phy0: ethernet-phy at 0 { /* Marvell 88E1518 */
+ reg = <0>;
+ /* LED2 is used to inform uBoot if the power-switch was slided
+ to the "off" position, and then power off the machine.
+ Page 0x3, Register 0x10, bit 8:
+ 0x800: LED2 off, power off the machine
+ 0x900: LED2 on, boot the machine */
+ marvell,reg-init = <0x3 0x10 0x1 0x1991>, /* LED Function */
+ <0x3 0x11 0x1 0x4401>, /* LED polarity */
+ <0x3 0x12 0x1 0x4905>; /* LED Timer */
+ };
+};
+
+&pciec {
+ status = "okay";
+ /* Connected to uPD720202 USB 3.0 Host */
+ pcie at 1,0 {
+ status = "okay";
+ };
+};
+
+&pmsu {
+ pinctrl-0 = <&pmx_power_cpu>;
+ pinctrl-names = "default";
+};
+
+&rtc {
+ status = "disabled";
+};
+
+&sata {
+ nr-ports = <2>;
+ status = "okay";
+};
+
+&sdio {
+ pinctrl-0 = <&sdio_pins2>;
+ pinctrl-names = "default";
+ status = "okay";
+ /* No CD or WP GPIOs */
+ broken-cd;
+};
+
+&uart0 {
+ status = "okay";
+};
+
+&usb0 {
+ status = "okay";
+};
+
+&nand_controller {
+ status = "okay";
+
+ nand at 0 {
+ reg = <0>;
+ label = "pxa3xx_nand-0";
+ nand-rb = <0>;
+ marvell,nand-keep-config;
+ nand-on-flash-bbt;
+ nand-ecc-strength = <4>;
+ nand-ecc-step-size = <512>;
+
+ partitions {
+ compatible = "fixed-partitions";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ partition at 0 {
+ label = "kernel";
+ reg = <0x00000000 0x02000000>; /* 32 MiB */
+ };
+
+ partition at 2000000 {
+ label = "ubi";
+ reg = <0x02000000 0x1e000000>; /* 480 MiB */
+ };
+ };
+ };
+};
+
+&spi0 {
+ status = "okay";
+ pinctrl-0 = <&spi0_pins2>;
+ pinctrl-names = "default";
+
+ spi-flash at 0 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "mxicy,mx25l8005", "jedec,spi-nor";
+ reg = <0>; /* Chip select 0 */
+ spi-max-frequency = <50000000>;
+
+ partitions {
+ compatible = "fixed-partitions";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ partition at 0 {
+ reg = <0x00000 0xf0000>; /* 960 KiB*/
+ label = "u-boot";
+ read-only;
+ };
+ partition at f0000 {
+ reg = <0xf0000 0x10000>; /* 64 KiB */
+ label = "u-boot-env";
+ };
+ };
+ };
+};
+
+&pinctrl {
+ pmx_power_cpu: pmx-power-cpu {
+ marvell,pins = "mpp4";
+ marvell,function = "vdd";
+ };
+ pmx_power_usb: pmx-power-usb {
+ marvell,pins = "mpp5";
+ marvell,function = "gpo";
+ };
+ pmx_power_hdd1: pmx-power-hdd1 {
+ marvell,pins = "mpp8";
+ marvell,function = "gpio";
+ };
+ pmx_power_hdd2: pmx-power-hdd2 {
+ marvell,pins = "mpp9";
+ marvell,function = "gpo";
+ };
+ pmx_fan_lock: pmx-fan-lock {
+ marvell,pins = "mpp10";
+ marvell,function = "gpio";
+ };
+ pmx_hdd_present: pmx-hdd-present {
+ marvell,pins = "mpp11", "mpp12";
+ marvell,function = "gpio";
+ };
+ pmx_fan_high: pmx-fan-high {
+ marvell,pins = "mpp13";
+ marvell,function = "gpio";
+ };
+ pmx_fan_low: pmx-fan-low {
+ marvell,pins = "mpp14";
+ marvell,function = "gpio";
+ };
+ pmx_buttons: pmx-buttons {
+ marvell,pins = "mpp15", "mpp16";
+ marvell,function = "gpio";
+ };
+ pmx_leds1: pmx-leds {
+ marvell,pins = "mpp7", "mpp54", "mpp59", "mpp61";
+ marvell,function = "gpo";
+ };
+ pmx_leds2: pmx-leds {
+ marvell,pins = "mpp55", "mpp57", "mpp62";
+ marvell,function = "gpio";
+ };
+};
diff --git a/target/linux/mvebu/image/Makefile b/target/linux/mvebu/image/Makefile
index ef9274866d..3a47878069 100644
--- a/target/linux/mvebu/image/Makefile
+++ b/target/linux/mvebu/image/Makefile
@@ -40,6 +40,20 @@ define Build/boot-img-ext4
make_ext4fs -J -L kernel -l $(CONFIG_TARGET_KERNEL_PARTSIZE)M $@.bootimg $@.boot
endef
+define Build/buffalo-kernel-jffs2
+ rm -rf $(KDIR)/kernel_jffs2 $@.fakerd
+ mkdir -p $(KDIR)/kernel_jffs2
+ dd if=/dev/zero of=$@.fakerd bs=131008 count=1 conv=sync
+ $(STAGING_DIR_HOST)/bin/mkimage \
+ -T ramdisk -A $(LINUX_KARCH) -O linux -C gzip -n 'fake initrd' \
+ -d $@.fakerd $(KDIR)/kernel_jffs2/initrd.buffalo
+ cp $@ $(KDIR)/kernel_jffs2/uImage.buffalo
+ $(STAGING_DIR_HOST)/bin/mkfs.jffs2 \
+ --little-endian -v --squash-uids -q -f -n -x lzma -x rtime -m none \
+ --eraseblock=128KiB --pad=$(KERNEL_SIZE) -d $(KDIR)/kernel_jffs2 -o $@
+ rm -rf $(KDIR)/kernel_jffs2 $@.fakerd
+endef
+
define Build/sdcard-img
SIGNATURE="$(IMG_PART_SIGNATURE)" \
./gen_mvebu_sdcard_img.sh $@ \
diff --git a/target/linux/mvebu/image/cortexa9.mk b/target/linux/mvebu/image/cortexa9.mk
index 85bfa94dbd..4ab6f4a7e8 100644
--- a/target/linux/mvebu/image/cortexa9.mk
+++ b/target/linux/mvebu/image/cortexa9.mk
@@ -6,6 +6,22 @@
# See /LICENSE for more information.
#
+define Device/buffalo_ls421de
+ $(Device/NAND-128K)
+ DEVICE_VENDOR := Buffalo
+ DEVICE_MODEL := LinkStation LS421DE
+ SUBPAGESIZE :=
+ KERNEL_SIZE := 33554432
+ FILESYSTEMS := squashfs ubifs
+ KERNEL := kernel-bin | append-dtb | uImage none | buffalo-kernel-jffs2
+ KERNEL_INITRAMFS := kernel-bin | append-dtb | uImage none
+ DEVICE_DTS := armada-370-buffalo-ls421de
+ DEVICE_PACKAGES := \
+ kmod-rtc-rs5c372a kmod-hwmon-gpiofan kmod-usb3 kmod-md-raid0 \
+ kmod-md-raid1 kmod-md-mod kmod-fs-xfs mkf2fs e2fsprogs partx-utils
+endef
+TARGET_DEVICES += buffalo_ls421de
+
define Device/cznic_turris-omnia
DEVICE_VENDOR := CZ.NIC
DEVICE_MODEL := Turris Omnia
--
2.26.0
_______________________________________________
openwrt-devel mailing list
openwrt-devel at lists.openwrt.org
https://lists.openwrt.org/mailman/listinfo/openwrt-devel
More information about the openwrt-devel
mailing list