[OpenWrt-Devel] QCA9994 outdoor 13km link
Maxnet Support
support at maxnet.al
Wed Sep 25 17:37:09 EDT 2019
I have attached iw phy phy0 info output. It shows only 2 antennas. Is this wrong? Qca9994 has 4 chains.
On 25 Sep 2019, 22:51, at 22:51, support at maxnet.al wrote:
>Hi,
>
>
>
>
>
>
>In the beginning i was using 2 dishes on each side. They are ubiquiti
>2x2 dual polarized dishes and i connected the chains of station in the
>same way as AP and i still had issues. After that i thought the problem
>might be because this card uses mimo multipath and AP ch0 should talk
>with station ch 0 1 2 3. With 2x2 dishes that's not possible because
>
>
>
>
>
>
>DISH 1
>
>
>
>
>CH0 -H
>
>
>
>
>CH1 -V
>
>
>
>
>
>
>CH2 -H
>
>
>
>
>CH3 -V
>
>
>
>
>
>
>The station pigtails were connected in the same way as AP.
>
>
>
>
>In this configuration AP ch0 whish is Horizontal can talk only with
>station ch0 and ch2.
>
>
>
>
>
>
>So i decided to go with Jiroues single polarity dishes on each side.
>You think that single polarity might be the problem but why it doesn't
>cause problems in routers when there are 4 omni antennas and still you
>can get datarates 866Mbps by phone(my phone is 2x2). The testing
>distance now is 5km but the distance where they will be installed is
>13km. We also have dozens of ubiquiti and mikrotik links and 13km it's
>not a big deal.
>
>
>
>
>
>
>Today also i noticed something strange. The AP was openwrt and station
>was ddwrt and i got 433/866 and after changing the station to openwrt
>the datarates got worse. Ddwrt wasn't good either. It had datarates
>problem.
>
>
>
>
>
>
>Can it be something wrong with firmware antenna configuration? Why it
>shows only two antennas iw phy phy0 info?
>
>
>
>
>
>
>Thank you
>
>
>
>
>
>
>
>
>
>On Wed, Sep 25, 2019 at 6:34 PM +0200, "Koen Vandeputte"
><koen.vandeputte at ncentric.com> wrote:
>
>
>
>
>
>
>
>
>
>
>
>On 25.09.19 17:14, support at maxnet.al wrote:
>> This is long distance, 5km with 4 dishes on each side. They are all
>> vertical and all chains have signal range -60 to -65.
>>
>> I don't have omni antennas. Is there a problem that i am using
>dishes?
>>
>>
>I run dozens of long-range devices, and I'm seeing 2 issues in your
>setup:
>
>1)
>
>- Ack-to issues kick in starting from roughly 1000m. When you cannot
>alter ack_to (coverage class), you will notice severe performance
>issues
>above 1000m
>
>2)
>
>- Using identical polarization on all chains is an absolute performance
>
>killer.
>
>I have 2 devices, both 2x2 802.11n, HT40 SGI, which are only 150m
>apart, all chains V polarized.
>
>When running speedtests, inspecting ath9k rate control shows it is
>stuck
>at the max speed for 1 chain (iso 2)
>
>In my case it means the absolute link rate is 130Mbit iso 270 in this
>configuration.
>
>I can imagine using 4 chains will even reduce performance a lot more.
>
>You should really try to use use H + V+ (-45) + (+45).
>
>Also, ensure radio's at both sides have the chains on identical
>polarization. (Chain0 - V, Chain1 - H, ..)
>
>
>Regards,
>
>Koen
>
>>
>> On Wed, Sep 25, 2019 at 5:11 PM +0200, "Ben Greear"
>> > wrote:
>>
>> Is this short distance or long?
>>
>> Please try short distance with omni antenna first to make sure
>you are not hitting the delayed-ack issue
>> or problems with your antenna.
>>
>> Change your antenna orientation so that they point in different
>directions.
>>
>> Thanks,
>> Ben
>>
>> On 9/25/19 6:49 AM, support at maxnet.al wrote:
>> > Hello,
>> >
>> > Today i managed to connect the station wds at 80MHz channel.
>Signal is -56 and i have very low datarates. I have attached a photo.
>> >
>> > When station was ddwrt and AP openwrt the datarates were
>866/433. TX won't do more than VHT-NSS 1 although RX it's not good
>either because it's a 4 chain
>> > radio and it should do VHT-NSS4.
>> >
>> > Thank you,
>> > Klevis
>> >
>> >
>> >
>> >
>> > On Mon, Sep 23, 2019 at 6:36 PM +0200, "Ben Greear" > wrote: >
>> Weeks or months or whenever I have time, and maybe
>> sooner if someone > wants to sponsor it. Please understand I, and
>> probably everyone else working > on OpenWRT, am busy with lots of
>> other projects and community work often > gets pushed to the back
>> burner. > > Thanks, > Ben > > On 9/23/19 8:18 AM,
>> support at maxnet.al wrote: > > Hi Ben, > > > > When do you think
>you
>> might be able to make those changes to your driver? > > > >
>> Thanks, > > Klevis. > > > > > > > > On 2019-09-20 13:00, Ben
>> Greear wrote: > >> On 9/20/19 12:55 PM, Vincent Wiemann wrote: >
>> >>> Hi Klevis, > >>> > >>> have you tried it with a short
>> distance? > >>> If you did you should better ask Ben Greear
>> directly. > >> > >> I asked him to post publicly so that others
>> can help answer and that > >> my own answers might > >> help
>> someone else. > >> > >> I have some patches that should enable
>> coverage class settings for > >> wave-2, but I am too busy > >>
>> with other things right now to port them to my ath10k-ct
>> driver/firmware. > >> > >> Thanks, > >> Ben > >> > >>> > >>> By
>> the way ath10k gen 2 chipsets don't work very well with long
>> distance links without a > >>> special feature which
>> implementation is only available to companies like Ubiquiti and
>> very few > >>> people who have an own reverse-engineered
>> implementation. > >>> It works on IPQ401X, QCA9886 and QCA9888
>> based chips only. > >>> > >>> And it is not possible to set a
>> coverage class for gen 2 devices, yet as far as I know due to
>> missing > >>> documentation and implementation (correct me if
>that
>> information is outdated). > >>> Furthermore a high channel width
>> often results in problems > >>> due to lower receiver
>sensibility.
>> > >>> We have better experiences with lower channel widths and
>> sometimes get more throughput with that. > >>> > >>> Actually I
>> think this does not explain your connection issues as 13 km is
>not
>> that much. > >>> > >>> Regards, > >>> > >>> Vincent Wiemann > >>>
>> > >>> On 20.09.19 18:30, support at maxnet.al wrote: > >>>> Hello
>> everyone, > >>>> > >>>> I am trying to setup a custom made
>outdoor
>> link with Apu2d2 board devices and QCA9994 cards from compex.
>> After i installed openwrt and ath10k ct driver, > >>>> kmod
>ath10k
>> and board-2.bin the device can run a 80MHz channel in WDS AP. The
>> problem is that it won't run as station or station wds. It can
>> scan > >>>> the SSIDs but won't connect them. > >>>> > >>>> Any
>> suggestion? > >>>> > >>>> Thank you! > >>>> Klevis > >>>> > >>> >
>> >>> _______________________________________________ > >>>
>> openwrt-devel mailing list > >>> openwrt-devel at lists.openwrt.org
>>
>> >>> https://lists.openwrt.org/mailman/listinfo/openwrt-devel >
>>>>
>> > > > > > -- > Ben GreearCandela Technologies Inc
>> http://www.candelatech.com > -- Ben Greear Candela Technologies
>> Inc http://www.candelatech.com
>>
>>
>> _______________________________________________
>> openwrt-devel mailing list
>> openwrt-devel at lists.openwrt.org
>> https://lists.openwrt.org/mailman/listinfo/openwrt-devel
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://lists.infradead.org/pipermail/openwrt-devel/attachments/20190925/96cd41fc/attachment.htm>
-------------- next part --------------
A non-text attachment was scrubbed...
Name: Screenshot_20190925-233504_VX ConnectBot.jpg
Type: image/jpeg
Size: 337263 bytes
Desc: not available
URL: <http://lists.infradead.org/pipermail/openwrt-devel/attachments/20190925/96cd41fc/attachment.jpg>
-------------- next part --------------
_______________________________________________
openwrt-devel mailing list
openwrt-devel at lists.openwrt.org
https://lists.openwrt.org/mailman/listinfo/openwrt-devel
More information about the openwrt-devel
mailing list