[OpenWrt-Devel] [PATCH v2] ath79: add support for Netgear WNR2200
John Crispin
john at phrozen.org
Thu Oct 31 08:48:06 EDT 2019
On 30/10/2019 10:07, Michal Cieslakiewicz wrote:
> This patch adds ath79 support for Netgear WNR2200.
> Router was previously supported by ar71xx target only (8 MiB variant).
> Netgear WNR2200 has two flash versions - 8MiB sold in EU, US etc. and
> 16 MiB for Russia and China markets. Apart from flash size both variants
> share the same hardware specification.
>
> Specification
> =============
> * Description: Netgear WNR2200
> * Loader: U-boot
> * SOC: Atheros AR7241 (360 MHz)
> * RAM: 64 MiB
> * Flash: 8 MiB or 16 MiB (SPI NOR)
> - U-boot binary: 256 KiB
> - U-boot environment: 64 KiB
> - Firmware: 7808 KiB or 16000 KiB
> - ART: 64 KiB
> * Ethernet: 4 x 10/100 LAN + 1 x 10/100 WAN
> * Wireless: 2.4 GHz b/g/n (Atheros AR9287)
> * USB: yes, 1 x USB 2.0
> * Buttons:
> - Reset
> - WiFi (rfkill)
> - WPS
> * LEDs:
> - Power (amber/green)
> - WAN (amber/green)
> - WLAN (blue)
> - 4 x LAN (amber/green)
> - WPS (green)
> * UART: 4-pin connector JP1, 3.3V (Vcc, TX, RX, GND), 115200 8N1
> * Power supply: DC 12V 1.5A
> * MAC addresses: LAN on case label, WAN +1, WLAN +2
>
> Installation
> ============
> * TFTP recovery
> * TFTP via U-boot prompt
> * sysupgrade
> * Web interface
>
> Test build configuration
> ========================
> CONFIG_TARGET_ath79=y
> CONFIG_TARGET_ath79_generic=y
> CONFIG_TARGET_ath79_generic_DEVICE_netgear_wnr2200-8m=y
> CONFIG_ALL_KMODS=y
> CONFIG_DEVEL=y
> CONFIG_CCACHE=y
> CONFIG_COLLECT_KERNEL_DEBUG=y
> CONFIG_IMAGEOPT=y
> CONFIG_KERNEL_DEBUG_INFO=y
> CONFIG_KERNEL_DEBUG_KERNEL=y
>
Hi,
sorry for the foo, patch fails to apply, kindly rebase/resend it
John
> Signed-off-by: Michal Cieslakiewicz <michal.cieslakiewicz at wp.pl>
> ---
> package/boot/uboot-envtools/files/ath79 | 2 +
> .../ath79/dts/ar7241_netgear_wnr2200-16m.dts | 34 +++
> .../ath79/dts/ar7241_netgear_wnr2200-8m.dts | 34 +++
> .../ath79/dts/ar7241_netgear_wnr2200.dtsi | 207 ++++++++++++++++++
> .../generic/base-files/etc/board.d/01_leds | 12 +
> .../generic/base-files/etc/board.d/02_network | 6 +
> .../etc/hotplug.d/firmware/10-ath9k-eeprom | 2 +
> target/linux/ath79/image/generic.mk | 34 +++
> 8 files changed, 331 insertions(+)
> create mode 100644 target/linux/ath79/dts/ar7241_netgear_wnr2200-16m.dts
> create mode 100644 target/linux/ath79/dts/ar7241_netgear_wnr2200-8m.dts
> create mode 100644 target/linux/ath79/dts/ar7241_netgear_wnr2200.dtsi
>
> diff --git a/package/boot/uboot-envtools/files/ath79 b/package/boot/uboot-envtools/files/ath79
> index d5b94823fd..cc9741cedf 100644
> --- a/package/boot/uboot-envtools/files/ath79
> +++ b/package/boot/uboot-envtools/files/ath79
> @@ -22,6 +22,8 @@ glinet,gl-ar300m-nor|\
> librerouter,librerouter-v1|\
> netgear,ex6400|\
> netgear,ex7300|\
> +netgear,wnr2200-8m|\
> +netgear,wnr2200-16m|\
> ocedo,koala|\
> ocedo,raccoon|\
> openmesh,om5p-ac-v2|\
> diff --git a/target/linux/ath79/dts/ar7241_netgear_wnr2200-16m.dts b/target/linux/ath79/dts/ar7241_netgear_wnr2200-16m.dts
> new file mode 100644
> index 0000000000..d182b58c05
> --- /dev/null
> +++ b/target/linux/ath79/dts/ar7241_netgear_wnr2200-16m.dts
> @@ -0,0 +1,34 @@
> +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
> +/dts-v1/;
> +
> +#include "ar7241_netgear_wnr2200.dtsi"
> +
> +/ {
> + compatible = "netgear,wnr2200-16m", "qca,ar7241";
> + model = "Netgear WNR2200 (16M)";
> +};
> +
> +&partitions {
> + partition at 0 {
> + label = "u-boot";
> + reg = <0x0 0x40000>;
> + read-only;
> + };
> +
> + partition at 40000 {
> + label = "u-boot-env";
> + reg = <0x40000 0x10000>;
> + };
> +
> + partition at 50000 {
> + label = "firmware";
> + reg = <0x50000 0xfa0000>;
> + compatible = "netgear,uimage";
> + };
> +
> + art: partition at ff0000 {
> + label = "art";
> + reg = <0xff0000 0x10000>;
> + read-only;
> + };
> +};
> diff --git a/target/linux/ath79/dts/ar7241_netgear_wnr2200-8m.dts b/target/linux/ath79/dts/ar7241_netgear_wnr2200-8m.dts
> new file mode 100644
> index 0000000000..e926c17893
> --- /dev/null
> +++ b/target/linux/ath79/dts/ar7241_netgear_wnr2200-8m.dts
> @@ -0,0 +1,34 @@
> +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
> +/dts-v1/;
> +
> +#include "ar7241_netgear_wnr2200.dtsi"
> +
> +/ {
> + compatible = "netgear,wnr2200-8m", "qca,ar7241";
> + model = "Netgear WNR2200 (8M)";
> +};
> +
> +&partitions {
> + partition at 0 {
> + label = "u-boot";
> + reg = <0x0 0x40000>;
> + read-only;
> + };
> +
> + partition at 40000 {
> + label = "u-boot-env";
> + reg = <0x40000 0x10000>;
> + };
> +
> + partition at 50000 {
> + label = "firmware";
> + reg = <0x50000 0x7a0000>;
> + compatible = "netgear,uimage";
> + };
> +
> + art: partition at 7f0000 {
> + label = "art";
> + reg = <0x7f0000 0x10000>;
> + read-only;
> + };
> +};
> diff --git a/target/linux/ath79/dts/ar7241_netgear_wnr2200.dtsi b/target/linux/ath79/dts/ar7241_netgear_wnr2200.dtsi
> new file mode 100644
> index 0000000000..1ce4d11835
> --- /dev/null
> +++ b/target/linux/ath79/dts/ar7241_netgear_wnr2200.dtsi
> @@ -0,0 +1,207 @@
> +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
> +/dts-v1/;
> +
> +#include <dt-bindings/gpio/gpio.h>
> +#include <dt-bindings/input/input.h>
> +
> +#include "ar7241.dtsi"
> +
> +/ {
> + chosen {
> + bootargs = "console=ttyS0,115200n8";
> + };
> +
> + aliases {
> + led-boot = &power_amber;
> + led-failsafe = &power_amber;
> + led-running = &power_green;
> + led-upgrade = &power_amber;
> + label-mac-device = ð1;
> + };
> +
> + ath9k-keys {
> + compatible = "gpio-keys-polled";
> + poll-interval = <20>;
> +
> + wps {
> + label = "wps";
> + linux,code = <KEY_WPS_BUTTON>;
> + gpios = <&ath9k 5 GPIO_ACTIVE_LOW>;
> + debounce-interval = <60>;
> + };
> +
> + reset {
> + label = "reset";
> + linux,code = <KEY_RESTART>;
> + gpios = <&ath9k 6 GPIO_ACTIVE_LOW>;
> + debounce-interval = <60>;
> + };
> +
> + rfkill {
> + label = "rfkill";
> + linux,code = <KEY_RFKILL>;
> + gpios = <&ath9k 3 GPIO_ACTIVE_LOW>;
> + debounce-interval = <60>;
> + };
> + };
> +
> + leds {
> + compatible = "gpio-leds";
> +
> + pinctrl-names = "default";
> + pinctrl-0 = <&jtag_disable_pins &switch_led_disable_pins &clks_disable_pins>;
> +
> + wan_green {
> + label = "netgear:green:wan";
> + gpios = <&gpio 17 GPIO_ACTIVE_LOW>;
> + };
> +
> + wan_amber {
> + label = "netgear:amber:wan";
> + gpios = <&gpio 12 GPIO_ACTIVE_LOW>;
> + };
> +
> + lan1_green {
> + label = "netgear:green:lan1";
> + gpios = <&gpio 13 GPIO_ACTIVE_LOW>;
> + };
> +
> + lan1_amber {
> + label = "netgear:amber:lan1";
> + gpios = <&gpio 6 GPIO_ACTIVE_LOW>;
> + };
> +
> + lan2_green {
> + label = "netgear:green:lan2";
> + gpios = <&gpio 14 GPIO_ACTIVE_LOW>;
> + };
> +
> + lan2_amber {
> + label = "netgear:amber:lan2";
> + gpios = <&gpio 0 GPIO_ACTIVE_LOW>;
> + };
> +
> + lan3_green {
> + label = "netgear:green:lan3";
> + gpios = <&gpio 15 GPIO_ACTIVE_LOW>;
> + };
> +
> + lan3_amber {
> + label = "netgear:amber:lan3";
> + gpios = <&gpio 11 GPIO_ACTIVE_LOW>;
> + };
> +
> + lan4_green {
> + label = "netgear:green:lan4";
> + gpios = <&gpio 16 GPIO_ACTIVE_LOW>;
> + };
> +
> + lan4_amber {
> + label = "netgear:amber:lan4";
> + gpios = <&gpio 1 GPIO_ACTIVE_LOW>;
> + };
> +
> + wps_green {
> + label = "netgear:green:wps";
> + gpios = <&gpio 7 GPIO_ACTIVE_LOW>;
> + };
> +
> + usb_green {
> + label = "netgear:green:usb";
> + gpios = <&gpio 8 GPIO_ACTIVE_LOW>;
> + trigger-sources = <&hub_port>;
> + linux,default-trigger = "usbport";
> + };
> + };
> +
> + ath9k-leds {
> + compatible = "gpio-leds";
> +
> + power_green: power_green {
> + label = "netgear:green:power";
> + gpios = <&ath9k 2 GPIO_ACTIVE_LOW>;
> + };
> +
> + power_amber: power_amber {
> + label = "netgear:amber:power";
> + gpios = <&ath9k 1 GPIO_ACTIVE_LOW>;
> + default-state = "keep";
> + };
> +
> + wlan_blue {
> + label = "netgear:blue:wlan";
> + gpios = <&ath9k 0 GPIO_ACTIVE_LOW>;
> + linux,default-trigger = "phy0tpt";
> + };
> + };
> +};
> +
> +&spi {
> + status = "okay";
> + num-cs = <1>;
> +
> + flash at 0 {
> + compatible = "jedec,spi-nor";
> + reg = <0>;
> + spi-max-frequency = <25000000>;
> +
> + partitions: partitions {
> + compatible = "fixed-partitions";
> + #address-cells = <1>;
> + #size-cells = <1>;
> + };
> + };
> +};
> +
> +ð0 {
> + status = "okay";
> +
> + mtd-mac-address = <&art 0x0>;
> +};
> +
> +ð1 {
> + status = "okay";
> +
> + compatible = "qca,ar7241-eth", "syscon", "simple-mfd";
> + mtd-mac-address = <&art 0x6>;
> +};
> +
> +&pcie {
> + status = "okay";
> +
> + ath9k: wifi at 0,0 {
> + compatible = "pci168c,002e";
> + reg = <0x0000 0 0 0 0>;
> + mtd-mac-address = <&art 0x0>;
> + mtd-mac-address-increment = <1>;
> + qca,no-eeprom;
> + #gpio-cells = <2>;
> + gpio-controller;
> +
> + usb_power {
> + gpio-hog;
> + line-name = "netgear:power:usb";
> + gpios = <4 GPIO_ACTIVE_HIGH>;
> + output-high;
> + };
> + };
> +};
> +
> +&uart {
> + status = "okay";
> +};
> +
> +&usb_phy {
> + status = "okay";
> +};
> +
> +&usb {
> + #address-cells = <1>;
> + #size-cells = <0>;
> + status = "okay";
> +
> + hub_port: port at 1 {
> + reg = <1>;
> + #trigger-source-cells = <0>;
> + };
> +};
> diff --git a/target/linux/ath79/generic/base-files/etc/board.d/01_leds b/target/linux/ath79/generic/base-files/etc/board.d/01_leds
> index e3575ff041..441091de32 100755
> --- a/target/linux/ath79/generic/base-files/etc/board.d/01_leds
> +++ b/target/linux/ath79/generic/base-files/etc/board.d/01_leds
> @@ -103,6 +103,18 @@ glinet,gl-ar300m-lite)
> glinet,gl-x750)
> ucidef_set_led_netdev "wan" "WAN" "$boardname:green:wan" "eth1"
> ;;
> +netgear,wnr2200-8m|\
> +netgear,wnr2200-16m)
> + ucidef_set_led_netdev "wan-amber" "WAN (amber)" "netgear:amber:wan" "eth0"
> + ucidef_set_led_switch "lan1green" "LAN1 (green)" "netgear:green:lan1" "switch0" "0x02" "0x04"
> + ucidef_set_led_switch "lan2green" "LAN2 (green)" "netgear:green:lan2" "switch0" "0x04" "0x04"
> + ucidef_set_led_switch "lan3green" "LAN3 (green)" "netgear:green:lan3" "switch0" "0x08" "0x04"
> + ucidef_set_led_switch "lan4green" "LAN4 (green)" "netgear:green:lan4" "switch0" "0x10" "0x04"
> + ucidef_set_led_switch "lan1amber" "LAN1 (amber)" "netgear:amber:lan1" "switch0" "0x02" "0x02"
> + ucidef_set_led_switch "lan2amber" "LAN2 (amber)" "netgear:amber:lan2" "switch0" "0x04" "0x02"
> + ucidef_set_led_switch "lan3amber" "LAN3 (amber)" "netgear:amber:lan3" "switch0" "0x08" "0x02"
> + ucidef_set_led_switch "lan4amber" "LAN4 (amber)" "netgear:amber:lan4" "switch0" "0x10" "0x02"
> + ;;
> pcs,cap324)
> ucidef_set_led_netdev "lan" "LAN" "pcs:lan:green" "eth0"
> ;;
> diff --git a/target/linux/ath79/generic/base-files/etc/board.d/02_network b/target/linux/ath79/generic/base-files/etc/board.d/02_network
> index 90f622b262..0cf411041d 100755
> --- a/target/linux/ath79/generic/base-files/etc/board.d/02_network
> +++ b/target/linux/ath79/generic/base-files/etc/board.d/02_network
> @@ -184,6 +184,12 @@ ath79_setup_interfaces()
> ucidef_add_switch_port_attr "switch0" 2 led 9
> ucidef_add_switch_port_attr "switch0" 5 led 2
> ;;
> + netgear,wnr2200-8m|\
> + netgear,wnr2200-16m)
> + ucidef_set_interface_wan "eth0"
> + ucidef_add_switch "switch0" \
> + "0 at eth1" "1:lan" "2:lan" "3:lan" "4:lan"
> + ;;
> phicomm,k2t)
> ucidef_add_switch "switch0" \
> "0 at eth0" "3:lan:1" "5:lan:2" "4:wan"
> diff --git a/target/linux/ath79/generic/base-files/etc/hotplug.d/firmware/10-ath9k-eeprom b/target/linux/ath79/generic/base-files/etc/hotplug.d/firmware/10-ath9k-eeprom
> index 4b07660f02..6a6484879a 100644
> --- a/target/linux/ath79/generic/base-files/etc/hotplug.d/firmware/10-ath9k-eeprom
> +++ b/target/linux/ath79/generic/base-files/etc/hotplug.d/firmware/10-ath9k-eeprom
> @@ -76,6 +76,8 @@ case "$FIRMWARE" in
> winchannel,wb2000)
> caldata_extract "art" 0x5000 0x440
> ;;
> + netgear,wnr2200-8m|\
> + netgear,wnr2200-16m|\
> pcs,cap324|\
> tplink,tl-wr2543-v1|\
> tplink,tl-wr842n-v1|\
> diff --git a/target/linux/ath79/image/generic.mk b/target/linux/ath79/image/generic.mk
> index cea903f253..70631c20d0 100644
> --- a/target/linux/ath79/image/generic.mk
> +++ b/target/linux/ath79/image/generic.mk
> @@ -794,6 +794,40 @@ define Device/netgear_wndr3800ch
> endef
> TARGET_DEVICES += netgear_wndr3800ch
>
> +define Device/netgear_wnr2200_common
> + ATH_SOC := ar7241
> + DEVICE_MODEL := WNR2200
> + DEVICE_PACKAGES := kmod-usb2 kmod-usb-ledtrig-usbport
> + NETGEAR_KERNEL_MAGIC := 0x32323030
> + NETGEAR_BOARD_ID := wnr2200
> + IMAGE/default := append-kernel | pad-to $$$$(BLOCKSIZE) | netgear-squashfs | \
> + append-rootfs | pad-rootfs
> + $(Device/netgear_ath79)
> +endef
> +
> +define Device/netgear_wnr2200-8m
> + $(Device/netgear_wnr2200_common)
> + DEVICE_VARIANT := 8M
> + NETGEAR_HW_ID := 29763600+08+64
> + IMAGE_SIZE := 7808k
> + IMAGES += factory-NA.img
> + IMAGE/factory-NA.img := $$(IMAGE/default) | netgear-dni NA | \
> + check-size $$$$(IMAGE_SIZE)
> + SUPPORTED_DEVICES += wnr2200
> +endef
> +TARGET_DEVICES += netgear_wnr2200-8m
> +
> +define Device/netgear_wnr2200-16m
> + $(Device/netgear_wnr2200_common)
> + DEVICE_VARIANT := 16M
> + DEVICE_ALT0_VENDOR := NETGEAR
> + DEVICE_ALT0_MODEL := WNR2200
> + DEVICE_ALT0_VARIANT := CN/RU
> + NETGEAR_HW_ID :=
> + IMAGE_SIZE := 16000k
> +endef
> +TARGET_DEVICES += netgear_wnr2200-16m
> +
> define Device/ocedo_koala
> ATH_SOC := qca9558
> DEVICE_VENDOR := Ocedo
>
_______________________________________________
openwrt-devel mailing list
openwrt-devel at lists.openwrt.org
https://lists.openwrt.org/mailman/listinfo/openwrt-devel
More information about the openwrt-devel
mailing list