[OpenWrt-Devel] [PATCH v2] ath79: add support for OCEDO Ursus
markus.scheck1 at gmail.com
markus.scheck1 at gmail.com
Thu Mar 21 11:43:27 EDT 2019
From: Markus Scheck <markus.scheck1 at gmail.com>
SOC: Qualcomm Atheros QCA9558
RAM: 128MB
FLASH: 16MB (Macronix MX25L12845EMI-10G)
WLAN1: QCA9558 2.4GHz 802.11bgn 3SS
WLAN2: QCA9880 5GHz 802.11ac 3SS
LED: Power, LAN1, LAN2, 2.4GHz, 5GHz
Serial:Next to SPI Flash,
Pinout is 3V3 - GND - TX - RX (Square Pin is 3V3)
The Serial setting is 115200-8-N-1
INSTALLATION:
1. Serve an OpenWrt ramdisk image named "ursus.bin".
Set your IP-address to 192.168.100.8/24.
2. Connect to the serial. Power up the device and interrupt
the boot process.
3. Set the correct bootcmd with
> setenv bootcmd run bootcmd_1
> saveenv
4. Run
> tftpboot 0x81000000 ursus.bin
> bootm 0x81000000
5. Wait for OpenWrt to boot up.
6. Transfer OpenWrt sysupdate image and flash via sysupgrade.
Signed-off-by: Markus Scheck <markus.scheck1 at gmail.com>
---
.../ath79/base-files/etc/board.d/02_network | 3 +-
.../etc/hotplug.d/firmware/11-ath10k-caldata | 3 +-
.../linux/ath79/dts/qca9558_ocedo_ursus.dts | 148 ++++++++++++++++++
target/linux/ath79/image/generic.mk | 9 ++
4 files changed, 161 insertions(+), 2 deletions(-)
create mode 100644 target/linux/ath79/dts/qca9558_ocedo_ursus.dts
diff --git a/target/linux/ath79/base-files/etc/board.d/02_network b/target/linux/ath79/base-files/etc/board.d/02_network
index 62318ee232..69b5c265b4 100755
--- a/target/linux/ath79/base-files/etc/board.d/02_network
+++ b/target/linux/ath79/base-files/etc/board.d/02_network
@@ -65,7 +65,8 @@ ath79_setup_interfaces()
"0 at eth0" "1:lan:1" "3:lan:4" "4:lan:3" "5:lan:2" "2:wan"
;;
devolo,dvl1200e|\
- devolo,dvl1750e)
+ devolo,dvl1750e|\
+ ocedo,ursus)
ucidef_set_interface_lan "eth0 eth1"
;;
dlink,dir-825-b1)
diff --git a/target/linux/ath79/base-files/etc/hotplug.d/firmware/11-ath10k-caldata b/target/linux/ath79/base-files/etc/hotplug.d/firmware/11-ath10k-caldata
index 8651c97099..661008da8f 100644
--- a/target/linux/ath79/base-files/etc/hotplug.d/firmware/11-ath10k-caldata
+++ b/target/linux/ath79/base-files/etc/hotplug.d/firmware/11-ath10k-caldata
@@ -119,7 +119,8 @@ case "$FIRMWARE" in
ath10kcal_extract "art" 20480 2116
ath10kcal_patch_mac_crc $(mtd_get_mac_text board_data 2176)
;;
- ocedo,koala)
+ ocedo,koala|\
+ ocedo,ursus)
ath10kcal_extract "art" 20480 2116
ath10kcal_patch_mac $(mtd_get_mac_binary art 12)
;;
diff --git a/target/linux/ath79/dts/qca9558_ocedo_ursus.dts b/target/linux/ath79/dts/qca9558_ocedo_ursus.dts
new file mode 100644
index 0000000000..ddd6e3047e
--- /dev/null
+++ b/target/linux/ath79/dts/qca9558_ocedo_ursus.dts
@@ -0,0 +1,148 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/dts-v1/;
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+
+#include "qca9557.dtsi"
+
+/ {
+ compatible = "ocedo,ursus", "qca,qca9557";
+ model = "OCEDO Ursus";
+
+ chosen {
+ bootargs = "console=ttyS0,115200n8";
+ };
+
+ leds {
+ compatible = "gpio-leds";
+
+
+ wifi2 {
+ label = "ursus:green:wlan2";
+ gpios = <&gpio 14 GPIO_ACTIVE_LOW>;
+ linux,default-trigger = "phy1tpt";
+ };
+
+ wifi5 {
+ label = "ursus:green:wlan5";
+ gpios = <&gpio 15 GPIO_ACTIVE_LOW>;
+ linux,default-trigger = "phy0tpt";
+ };
+
+ };
+
+};
+
+&pcie1 {
+ status = "okay";
+};
+
+&uart {
+ status = "okay";
+};
+
+&pll {
+ clocks = <&extosc>;
+};
+
+&spi {
+ status = "okay";
+ num-cs = <1>;
+
+ flash at 0 {
+ compatible = "jedec,spi-nor";
+ reg = <0>;
+ spi-max-frequency = <25000000>;
+
+ partitions {
+ compatible = "fixed-partitions";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ uboot: partition at 0 {
+ label = "u-boot";
+ reg = <0x000000 0x040000>;
+ read-only;
+ };
+
+ partition at 40000 {
+ label = "u-boot-env";
+ reg = <0x040000 0x010000>;
+ };
+
+ partition at 50000 {
+ compatible = "denx,uimage";
+ label = "firmware";
+ reg = <0x050000 0x740000>;
+ };
+
+ partition at 790000 {
+ label = "vendor";
+ reg = <0x790000 0x740000>;
+ read-only;
+ };
+
+ partition at ed0000 {
+ label = "data";
+ reg = <0xed0000 0x110000>;
+ read-only;
+ };
+
+ partition at fe0000 {
+ label = "id";
+ reg = <0xfe0000 0x010000>;
+ read-only;
+ };
+
+ art: partition at ff0000 {
+ label = "art";
+ reg = <0xff0000 0x010000>;
+ read-only;
+ };
+ };
+ };
+};
+
+&wmac {
+ status = "okay";
+
+ mtd-cal-data = <&art 0x1000>;
+ mtd-mac-address = <&art 0x06>;
+};
+
+&mdio0 {
+ status = "okay";
+
+ phy1: ethernet-phy at 1 {
+ reg = <1>;
+ };
+
+ phy2: ethernet-phy at 2 {
+ reg = <2>;
+ };
+};
+
+ð0 {
+ status = "okay";
+ mtd-mac-address = <&art 0x00>;
+ phy-handle = <&phy1>;
+ pll-data = <0xa6000000 0x80000101 0x80001313>;
+
+ gmac_config: gmac-config {
+ device = <&gmac>;
+
+ rxdv-delay = <3>;
+ rxd-delay = <3>;
+ txen-delay = <0>;
+ txd-delay = <0>;
+ rgmii-enabled = <1>;
+ };
+};
+
+ð1 {
+ status = "okay";
+ mtd-mac-address = <&art 0x12>;
+ phy-handle = <&phy2>;
+ pll-data = <0x3000101 0x101 0x1313>;
+};
diff --git a/target/linux/ath79/image/generic.mk b/target/linux/ath79/image/generic.mk
index ddf0e62898..042a342034 100644
--- a/target/linux/ath79/image/generic.mk
+++ b/target/linux/ath79/image/generic.mk
@@ -468,6 +468,15 @@ define Device/ocedo_raccoon
endef
TARGET_DEVICES += ocedo_raccoon
+define Device/ocedo_ursus
+ ATH_SOC := qca9558
+ DEVICE_TITLE := OCEDO Ursus
+ DEVICE_PACKAGES := kmod-ath10k-ct ath10k-firmware-qca988x-ct
+ IMAGE_SIZE := 7424k
+ IMAGE/sysupgrade.bin := append-kernel | append-rootfs | pad-rootfs | append-metadata | check-size $$$$(IMAGE_SIZE)
+endef
+TARGET_DEVICES += ocedo_ursus
+
define Device/openmesh_om5p-ac-v2
ATH_SOC := qca9558
DEVICE_TITLE := OpenMesh OM5P-AC v2
--
2.21.0
_______________________________________________
openwrt-devel mailing list
openwrt-devel at lists.openwrt.org
https://lists.openwrt.org/mailman/listinfo/openwrt-devel
More information about the openwrt-devel
mailing list