[OpenWrt-Devel] [PATCH] ramips: add Netgear EX6150
David Bauer
mail at david-bauer.net
Thu Mar 21 10:55:09 EDT 2019
SoC: MediaTek MT7621
RAM: 64M (Winbond W9751G6KB-25)
FLASH: 16MB (Macronix MX25L12835F)
WiFi: MediaTek MT7662E bgn 2SS
WiFi: MediaTek MT7662E nac 2SS
BTN: ON/OFF - Reset - WPS - AP/Extender toggle
LED: - Arrow Right (blue)
- Arrow Left (blue)
- WiFi 1 (red/green)
- WiFi 2 (red/green)
- Power (green/amber)
- WPS (Green)
UART: UART is present as Pads on the backside of the PCB. They are
located on the other side of the Ethernet port.
3.3V - GND - TX - RX / 57600-8N1
3.3V is the nearest one to the antenna connectors
Installation
------------
Update the factory image via the Netgear web-interfaces (by default:
192.168.1.250/24).
You can also use the factory image with the nmrpflash tool.
For more information see https://github.com/jclehner/nmrpflash
Signed-off-by: David Bauer <mail at david-bauer.net>
---
.../ramips/base-files/etc/board.d/01_leds | 4 +
.../ramips/base-files/etc/board.d/02_network | 1 +
target/linux/ramips/dts/EX6150.dts | 245 ++++++++++++++++++
target/linux/ramips/image/mt7621.mk | 11 +
4 files changed, 261 insertions(+)
create mode 100644 target/linux/ramips/dts/EX6150.dts
diff --git a/target/linux/ramips/base-files/etc/board.d/01_leds b/target/linux/ramips/base-files/etc/board.d/01_leds
index 9cca231ab6..1aaab994c1 100755
--- a/target/linux/ramips/base-files/etc/board.d/01_leds
+++ b/target/linux/ramips/base-files/etc/board.d/01_leds
@@ -264,6 +264,10 @@ mtc,wr1201)
mzk-ex750np)
set_wifi_led "$boardname:red:wifi"
;;
+netgear,ex6150)
+ ucidef_set_led_wlan "wlan2g" "WiFi 2.4GHz" "$boardname:green:router" "phy1tpt"
+ ucidef_set_led_wlan "wlan5g" "WiFi 5GHz" "$boardname:green:client" "phy0tpt"
+ ;;
netgear,r6120)
ucidef_set_led_switch "lan" "lan" "$boardname:green:lan" "switch0" "0x0f"
ucidef_set_led_switch "wan" "wan" "$boardname:green:wan" "switch0" "0x10"
diff --git a/target/linux/ramips/base-files/etc/board.d/02_network b/target/linux/ramips/base-files/etc/board.d/02_network
index 890efa0d93..568ad97c73 100755
--- a/target/linux/ramips/base-files/etc/board.d/02_network
+++ b/target/linux/ramips/base-files/etc/board.d/02_network
@@ -368,6 +368,7 @@ ramips_setup_interfaces()
ucidef_add_switch "switch0" \
"0:lan:4" "1:lan:3" "2:lan:2" "3:lan:1" "5:wan" "6 at eth0"
;;
+ netgear,ex6150|\
re350-v1)
ucidef_add_switch "switch0" \
"0:lan" "6 at eth0"
diff --git a/target/linux/ramips/dts/EX6150.dts b/target/linux/ramips/dts/EX6150.dts
new file mode 100644
index 0000000000..540fa513b8
--- /dev/null
+++ b/target/linux/ramips/dts/EX6150.dts
@@ -0,0 +1,245 @@
+/dts-v1/;
+
+#include "mt7621.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+
+/ {
+ compatible = "netgear,ex6150", "mediatek,mt7621-soc";
+ model = "Netgear EX6150";
+
+ aliases {
+ led-boot = &power_green;
+ led-failsafe = &power_amber;
+ led-running = &power_green;
+ led-upgrade = &power_amber;
+ };
+
+ memory at 0 {
+ device_type = "memory";
+ reg = <0x0 0x4000000>;
+ };
+
+ chosen {
+ bootargs = "console=ttyS0,57600";
+ };
+
+ leds {
+ compatible = "gpio-leds";
+
+ power_amber: power_amber {
+ label = "ex6150:amber:power";
+ gpios = <&gpio0 15 GPIO_ACTIVE_LOW>;
+ };
+
+ power_green: power_green {
+ label = "ex6150:green:power";
+ gpios = <&gpio0 13 GPIO_ACTIVE_LOW>;
+ };
+
+ wps {
+ label = "ex6150:green:wps";
+ gpios = <&gpio0 16 GPIO_ACTIVE_LOW>;
+ };
+
+ rightarrow {
+ label = "ex6150:blue:rightarrow";
+ gpios = <&gpio0 28 GPIO_ACTIVE_LOW>;
+ };
+
+ leftarrow {
+ label = "ex6150:blue:leftarrow";
+ gpios = <&gpio0 31 GPIO_ACTIVE_LOW>;
+ };
+
+ router_green {
+ label = "ex6150:green:router";
+ gpios = <&gpio0 29 GPIO_ACTIVE_LOW>;
+ };
+
+ router_red {
+ label = "ex6150:red:router";
+ gpios = <&gpio0 30 GPIO_ACTIVE_LOW>;
+ };
+
+ client_green {
+ label = "ex6150:green:client";
+ gpios = <&gpio1 1 GPIO_ACTIVE_LOW>;
+ };
+
+ client_red {
+ label = "ex6150:red:client";
+ gpios = <&gpio1 0 GPIO_ACTIVE_LOW>;
+ };
+ };
+
+ keys {
+ compatible = "gpio-keys-polled";
+ poll-interval = <20>;
+
+ wps {
+ label = "wps";
+ gpios = <&gpio1 15 GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_WPS_BUTTON>;
+ };
+
+ reset {
+ label = "reset";
+ gpios = <&gpio1 14 GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_RESTART>;
+ };
+
+ toggle {
+ label = "AP/Extender toggle";
+ gpios = <&gpio1 16 GPIO_ACTIVE_LOW>;
+ linux,code = <BTN_0>;
+ /* Active when switch is set to "Access Point" */
+ };
+ };
+};
+
+&spi0 {
+ status = "okay";
+
+ m25p80 at 0 {
+ compatible = "jedec,spi-nor";
+ reg = <0>;
+ spi-max-frequency = <10000000>;
+
+ partitions {
+ compatible = "fixed-partitions";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ partition at 0 {
+ label = "u-boot";
+ reg = <0x0 0x30000>;
+ read-only;
+ };
+
+ partition at 30000 {
+ label = "config";
+ reg = <0x30000 0x10000>;
+ read-only;
+ };
+
+ factory: partition at 40000 {
+ label = "factory";
+ reg = <0x40000 0x10000>;
+ read-only;
+ };
+
+ partition at 50000 {
+ compatible = "denx,uimage";
+ label = "firmware";
+ reg = <0x50000 0xe80000>;
+ };
+
+ partition at ed0000 {
+ label = "ML1";
+ reg = <0xed0000 0x10000>;
+ read-only;
+ };
+
+ partition at ef0000 {
+ label = "ML2";
+ reg = <0xef0000 0x20000>;
+ read-only;
+ };
+
+ partition at f10000 {
+ label = "ML3";
+ reg = <0xf10000 0x20000>;
+ read-only;
+ };
+
+ partition at f30000 {
+ label = "ML4";
+ reg = <0xf30000 0x20000>;
+ read-only;
+ };
+
+ partition at f50000 {
+ label = "ML5";
+ reg = <0xf50000 0x20000>;
+ read-only;
+ };
+
+ partition at f70000 {
+ label = "ML6";
+ reg = <0xf70000 0x20000>;
+ read-only;
+ };
+
+ partition at f90000 {
+ label = "ML7";
+ reg = <0xf90000 0x20000>;
+ read-only;
+ };
+
+ partition at fb0000 {
+ label = "T_Meter1";
+ reg = <0xfb0000 0x10000>;
+ read-only;
+ };
+
+ partition at fc0000 {
+ label = "T_Meter2";
+ reg = <0xfc0000 0x10000>;
+ read-only;
+ };
+
+ partition at fd0000 {
+ label = "POT";
+ reg = <0xfd0000 0x10000>;
+ read-only;
+ };
+
+ partition at fe0000 {
+ label = "board_data";
+ reg = <0xfe0000 0x10000>;
+ read-only;
+ };
+
+ partition at ff0000 {
+ label = "nvram";
+ reg = <0xff0000 0x10000>;
+ read-only;
+ };
+ };
+ };
+};
+
+&pcie {
+ status = "okay";
+};
+
+&pcie0 {
+ wifi at 0,0 {
+ reg = <0x0000 0 0 0 0>;
+ mediatek,mtd-eeprom = <&factory 0x8000>;
+ ieee80211-freq-limit = <5000000 6000000>;
+ };
+};
+
+&pcie1 {
+ wifi at 0,0 {
+ reg = <0x0000 0 0 0 0>;
+ mediatek,mtd-eeprom = <&factory 0x0000>;
+ ieee80211-freq-limit = <2400000 2500000>;
+ };
+};
+
+ðernet {
+ mtd-mac-address = <&factory 0x00000004>;
+};
+
+&pinctrl {
+ state_default: pinctrl0 {
+ gpio {
+ ralink,group = "sdhci", "rgmii2", "jtag";
+ ralink,function = "gpio";
+ };
+ };
+};
diff --git a/target/linux/ramips/image/mt7621.mk b/target/linux/ramips/image/mt7621.mk
index 8b0b28a941..31b7216daa 100644
--- a/target/linux/ramips/image/mt7621.mk
+++ b/target/linux/ramips/image/mt7621.mk
@@ -323,6 +323,17 @@ define Device/r6220
endef
TARGET_DEVICES += r6220
+define Device/netgear_ex6150
+ DTS := EX6150
+ DEVICE_TITLE := Netgear EX6150
+ DEVICE_PACKAGES := kmod-mt76x2 wpad-basic
+ NETGEAR_BOARD_ID := U12H318T00_NETGEAR
+ IMAGE_SIZE := 14848k
+ IMAGES += factory.chk
+ IMAGE/factory.chk := $$(sysupgrade_bin) | check-size $$$$(IMAGE_SIZE) | netgear-chk
+endef
+TARGET_DEVICES += netgear_ex6150
+
define Device/netgear_r6350
DTS := R6350
BLOCKSIZE := 128k
--
2.21.0
_______________________________________________
openwrt-devel mailing list
openwrt-devel at lists.openwrt.org
https://lists.openwrt.org/mailman/listinfo/openwrt-devel
More information about the openwrt-devel
mailing list