[OpenWrt-Devel] [PATCH 2/2] ipq40xx: add support for AVM FRITZ!Repeater 3000
David Bauer
mail at david-bauer.net
Tue Mar 5 13:38:38 EST 2019
Hardware
--------
CPU: Qualcomm IPQ4019
RAM: 256M
FLASH: 128M NAND
ETH: Qualcomm QCA8072
WiFi2: IPQ4019 2T2R 2SS b/g/n
WiFi5: IPQ4019 2T2R 2SS n/ac
WiFi5: QCA9984 4T4R 4SS n/ac
LED: - Connect green/blue/red
- Power green
BTN: WPS/Connect
UART: 115200n8 3.3V
VCC - RX - TX - GND (Square is VCC)
Installation
------------
1. Grab the uboot for the Device from the 'u-boot-fritz3000'
subdirectory. Place it in the same directory as the 'eva_ramboot.py'
script. It is located in the 'scripts/flashing' subdirectory of the
OpenWRT tree.
2. Assign yourself the IP address 192.168.178.10/24. Connect your
Computer to one of the boxes LAN ports.
3. Connect Power to the Box. As soon as the LAN port of your computer
shows link, load the U-Boot to the box using following command.
> ./eva_ramboot.py --offset 0x85000000 192.168.178.1 uboot-fritz3000.bin
4. The U-Boot will now start. Now assign yourself the IP address
192.168.1.70/24. Copy the OpenWRT initramfs (!) image to a TFTP
server root directory and rename it to 'FRITZ3000.bin'.
5. The Box will now boot OpenWRT from RAM. This can take up to two
minutes.
6. Copy the U-Boot and the OpenWRT sysupgrade (!) image to the Box using
scp. SSH into the Box and first write the Bootloader to both previous
kernel partitions.
> mtd write /path/to/uboot-fritz3000.bin uboot0
> mtd write /path/to/uboot-fritz3000.bin uboot1
7. Remove the AVM filesystem partitions to make room for our kernel +
rootfs + overlayfs.
> ubirmvol /dev/ubi0 --name=avm_filesys_0
> ubirmvol /dev/ubi0 --name=avm_filesys_1
8. Flash OpenWRT peristently using sysupgrade.
> sysupgrade -n /path/to/openwrt-sysupgrade.bin
Signed-off-by: David Bauer <mail at david-bauer.net>
---
package/boot/uboot-fritz4040/Makefile | 7 +-
.../ipq40xx/base-files/etc/board.d/02_network | 1 +
.../etc/hotplug.d/firmware/11-ath10k-caldata | 10 +-
.../base-files/lib/upgrade/platform.sh | 1 +
.../dts/qcom-ipq4019-fritzrepeater-3000.dts | 261 +++++++++++++++++
.../dts/qcom-ipq4019-fritzrepeater-3000.dts | 265 ++++++++++++++++++
target/linux/ipq40xx/image/Makefile | 9 +
.../901-arm-boot-add-dts-files.patch | 3 +-
.../901-arm-boot-add-dts-files.patch | 3 +-
9 files changed, 555 insertions(+), 5 deletions(-)
create mode 100644 target/linux/ipq40xx/files-4.14/arch/arm/boot/dts/qcom-ipq4019-fritzrepeater-3000.dts
create mode 100644 target/linux/ipq40xx/files-4.19/arch/arm/boot/dts/qcom-ipq4019-fritzrepeater-3000.dts
diff --git a/package/boot/uboot-fritz4040/Makefile b/package/boot/uboot-fritz4040/Makefile
index 3182842c89..015ca1deb9 100644
--- a/package/boot/uboot-fritz4040/Makefile
+++ b/package/boot/uboot-fritz4040/Makefile
@@ -25,6 +25,11 @@ define U-Boot/Default
UBOOT_IMAGE:=uboot-$(1).bin
endef
+define U-Boot/fritz3000
+ NAME:=FritzRepeater 3000
+ BUILD_DEVICES:=avm_fritzrepeater-3000
+endef
+
define U-Boot/fritz4040
NAME:=FritzBox 4040
BUILD_DEVICES:=avm_fritzbox-4040
@@ -61,6 +66,6 @@ define Package/u-boot/install
$(INSTALL_BIN) $(PKG_BUILD_DIR)/upload-to-f4040.sh $(1)/
endef
-UBOOT_TARGETS := fritz4040 fritz7530
+UBOOT_TARGETS := fritz3000 fritz4040 fritz7530
$(eval $(call BuildPackage/U-Boot))
diff --git a/target/linux/ipq40xx/base-files/etc/board.d/02_network b/target/linux/ipq40xx/base-files/etc/board.d/02_network
index 9c232d49f7..5f1f87974a 100755
--- a/target/linux/ipq40xx/base-files/etc/board.d/02_network
+++ b/target/linux/ipq40xx/base-files/etc/board.d/02_network
@@ -37,6 +37,7 @@ ipq40xx_setup_interfaces()
ucidef_add_switch "switch0" \
"0u at eth0" "1:lan" "2:lan" "3:lan" "4:lan"
;;
+ avm,fritzrepeater-3000|\
compex,wpj428)
ucidef_set_interface_lan "eth0 eth1"
;;
diff --git a/target/linux/ipq40xx/base-files/etc/hotplug.d/firmware/11-ath10k-caldata b/target/linux/ipq40xx/base-files/etc/hotplug.d/firmware/11-ath10k-caldata
index 1264d2ef36..8520dfb41d 100644
--- a/target/linux/ipq40xx/base-files/etc/hotplug.d/firmware/11-ath10k-caldata
+++ b/target/linux/ipq40xx/base-files/etc/hotplug.d/firmware/11-ath10k-caldata
@@ -111,6 +111,10 @@ case "$FIRMWARE" in
ln -sf /lib/firmware/ath10k/pre-cal-pci-0000\:00\:00.0.bin \
/lib/firmware/ath10k/QCA9888/hw2.0/board.bin
;;
+ avm,fritzrepeater-3000)
+ /usr/bin/fritz_cal_extract -i 1 -s 0x3D000 -e 0x212 -l 12064 -o /lib/firmware/$FIRMWARE $(find_mtd_chardev "urlader0") || \
+ /usr/bin/fritz_cal_extract -i 1 -s 0x3D000 -e 0x212 -l 12064 -o /lib/firmware/$FIRMWARE $(find_mtd_chardev "urlader1")
+ ;;
openmesh,a62)
ath10kcal_extract "0:ART" 36864 12064
;;
@@ -135,7 +139,8 @@ case "$FIRMWARE" in
avm,fritzbox-4040)
/usr/bin/fritz_cal_extract -i 1 -s 0x400 -e 0x207 -l 12064 -o /lib/firmware/$FIRMWARE $(find_mtd_chardev "urlader_config")
;;
- avm,fritzbox-7530)
+ avm,fritzbox-7530 |\
+ avm,fritzrepeater-3000)
/usr/bin/fritz_cal_extract -i 1 -s 0x3C000 -e 0x207 -l 12064 -o /lib/firmware/$FIRMWARE $(find_mtd_chardev "urlader0") || \
/usr/bin/fritz_cal_extract -i 1 -s 0x3C000 -e 0x207 -l 12064 -o /lib/firmware/$FIRMWARE $(find_mtd_chardev "urlader1")
;;
@@ -183,7 +188,8 @@ case "$FIRMWARE" in
avm,fritzbox-4040)
/usr/bin/fritz_cal_extract -i 1 -s 0x400 -e 0x208 -l 12064 -o /lib/firmware/$FIRMWARE $(find_mtd_chardev "urlader_config")
;;
- avm,fritzbox-7530)
+ avm,fritzbox-7530 |\
+ avm,fritzrepeater-3000)
/usr/bin/fritz_cal_extract -i 1 -s 0x3C800 -e 0x208 -l 12064 -o /lib/firmware/$FIRMWARE $(find_mtd_chardev "urlader0") || \
/usr/bin/fritz_cal_extract -i 1 -s 0x3C800 -e 0x208 -l 12064 -o /lib/firmware/$FIRMWARE $(find_mtd_chardev "urlader1")
;;
diff --git a/target/linux/ipq40xx/base-files/lib/upgrade/platform.sh b/target/linux/ipq40xx/base-files/lib/upgrade/platform.sh
index 9a2c13cf4d..84b123335c 100644
--- a/target/linux/ipq40xx/base-files/lib/upgrade/platform.sh
+++ b/target/linux/ipq40xx/base-files/lib/upgrade/platform.sh
@@ -49,6 +49,7 @@ platform_do_upgrade() {
8dev,jalapeno |\
alfa-network,ap120c-ac |\
avm,fritzbox-7530 |\
+ avm,fritzrepeater-3000|\
qxwlan,e2600ac-c2)
nand_do_upgrade "$ARGV"
;;
diff --git a/target/linux/ipq40xx/files-4.14/arch/arm/boot/dts/qcom-ipq4019-fritzrepeater-3000.dts b/target/linux/ipq40xx/files-4.14/arch/arm/boot/dts/qcom-ipq4019-fritzrepeater-3000.dts
new file mode 100644
index 0000000000..b73a214c09
--- /dev/null
+++ b/target/linux/ipq40xx/files-4.14/arch/arm/boot/dts/qcom-ipq4019-fritzrepeater-3000.dts
@@ -0,0 +1,261 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+
+#include "qcom-ipq4019.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/soc/qcom,tcsr.h>
+
+/ {
+ model = "AVM FRITZ!Repeater 3000";
+ compatible = "avm,fritzrepeater-3000";
+
+ aliases {
+ led-boot = &power_led;
+ led-failsafe = &power_led;
+ led-running = &power_led;
+ led-upgrade = &power_led;
+ };
+
+ soc {
+ mdio at 90000 {
+ status = "okay";
+ };
+
+ ess-psgmii at 98000 {
+ status = "okay";
+ };
+
+ tcsr at 1949000 {
+ compatible = "qcom,tcsr";
+ reg = <0x1949000 0x100>;
+ qcom,wifi_glb_cfg = <TCSR_WIFI_GLB_CFG>;
+ };
+
+ ess_tcsr at 1953000 {
+ compatible = "qcom,tcsr";
+ reg = <0x1953000 0x1000>;
+ qcom,ess-interface-select = <TCSR_ESS_PSGMII>;
+ };
+
+ tcsr at 1957000 {
+ compatible = "qcom,tcsr";
+ reg = <0x1957000 0x100>;
+ qcom,wifi_noc_memtype_m0_m2 = <TCSR_WIFI_NOC_MEMTYPE_M0_M2>;
+ };
+
+ crypto at 8e3a000 {
+ status = "okay";
+ };
+
+ watchdog at b017000 {
+ status = "okay";
+ };
+
+ ess-switch at c000000 {
+ status = "okay";
+
+ switch_lan_bmp = <0x10>;
+ switch_wan_bmp = <0x20>;
+ };
+
+ edma at c080000 {
+ status = "okay";
+ };
+ };
+
+ keys {
+ compatible = "gpio-keys";
+
+ connect {
+ label = "Connect";
+ gpios = <&tlmm 10 GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_WPS_BUTTON>;
+ };
+ };
+
+ leds {
+ compatible = "gpio-leds";
+
+ connect_red {
+ label = "fritzwlan-3000:red:connect";
+ gpios = <&tlmm 30 GPIO_ACTIVE_LOW>;
+ };
+
+ connect_green {
+ label = "fritzwlan-3000:green:connect";
+ gpios = <&tlmm 31 GPIO_ACTIVE_LOW>;
+ };
+
+ connect_blue {
+ label = "fritzwlan-3000:blue:connect";
+ gpios = <&tlmm 32 GPIO_ACTIVE_LOW>;
+ };
+
+ power_led: power {
+ label = "fritzwlan-3000:green:power";
+ gpios = <&tlmm 33 GPIO_ACTIVE_LOW>;
+ };
+ };
+};
+
+&tlmm {
+ serial_0_pins: serial_pinmux {
+ mux {
+ pins = "gpio16", "gpio17";
+ function = "blsp_uart0";
+ bias-disable;
+ };
+ };
+
+ nand_pins: nand_pins {
+ pullups {
+ pins = "gpio53", "gpio58", "gpio59";
+ function = "qpic";
+ bias-pull-up;
+ };
+
+ pulldowns {
+ pins = "gpio54", "gpio55", "gpio56",
+ "gpio57", "gpio60", "gpio61",
+ "gpio62", "gpio63", "gpio64",
+ "gpio65", "gpio66", "gpio67",
+ "gpio68", "gpio69";
+ function = "qpic";
+ bias-pull-down;
+ };
+ };
+};
+
+&nand {
+ pinctrl-0 = <&nand_pins>;
+ pinctrl-names = "default";
+ status = "okay";
+ cs-gpios = <&tlmm 54 GPIO_ACTIVE_HIGH>;
+
+ nand at 0 {
+ partitions {
+ compatible = "fixed-partitions";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ partition at 0 {
+ label = "SBL1";
+ reg = <0x000000 0x80000>;
+ read-only;
+ };
+
+ partition at 80000 {
+ label = "MIBIB";
+ reg = <0x080000 0x80000>;
+ read-only;
+ };
+
+ partition at 100000 {
+ label = "QSEE";
+ reg = <0x100000 0x80000>;
+ read-only;
+ };
+
+ partition at 180000 {
+ label = "CDT";
+ reg = <0x180000 0x40000>;
+ read-only;
+ };
+
+ partition at 1c0000 {
+ label = "QSEE_B";
+ reg = <0x1c0000 0x80000>;
+ read-only;
+ };
+
+ partition at 240000 {
+ label = "urlader0";
+ reg = <0x240000 0x40000>;
+ read-only;
+ };
+
+ partition at 280000 {
+ label = "urlader1";
+ reg = <0x280000 0x40000>;
+ read-only;
+ };
+
+ partition at 2c0000 {
+ label = "nand-tffs";
+ reg = <0x2c0000 0x840000>;
+ read-only;
+ };
+
+ partition at b00000 {
+ /* 'kernel1' in AVM firmware */
+ label = "uboot0";
+ reg = <0xb00000 0x400000>;
+ };
+
+ partition at f00000 {
+ /* 'kernel2' in AVM firmware */
+ label = "uboot1";
+ reg = <0xf00000 0x400000>;
+ };
+
+ partition at 1300000 {
+ label = "ubi";
+ reg = <0x1300000 0x6d00000>;
+ };
+ };
+ };
+};
+
+&cryptobam {
+ status = "okay";
+};
+
+&blsp_dma {
+ status = "okay";
+};
+
+&blsp1_uart1 {
+ pinctrl-0 = <&serial_0_pins>;
+ pinctrl-names = "default";
+ status = "okay";
+};
+
+&qpic_bam {
+ status = "okay";
+};
+
+&wifi0 {
+ status = "okay";
+ /* BDFs are identical for the FRITZ!Box 7530 and the FRITZ!Repeater 3000 */
+ qcom,ath10k-calibration-variant = "AVM-FRITZBox-7530";
+};
+
+&wifi1 {
+ status = "okay";
+ ieee80211-freq-limit = <5170000 5350000>;
+ /* BDFs are identical for the FRITZ!Box 7530 and the FRITZ!Repeater 3000 */
+ qcom,ath10k-calibration-variant = "AVM-FRITZBox-7530";
+};
+
+&pcie0 {
+ status = "okay";
+
+ perst-gpio = <&tlmm 35 GPIO_ACTIVE_LOW>;
+ wake-gpio = <&tlmm 50 GPIO_ACTIVE_LOW>;
+
+ bridge at 0,0 {
+ reg = <0x00000000 0 0 0 0>;
+ #address-cells = <3>;
+ #size-cells = <2>;
+ ranges;
+
+ wifi at 1,0 {
+ /* QCA9984 */
+ compatible = "qcom,ath10k";
+ status = "okay";
+ reg = <0x00010000 0 0 0 0>;
+ ieee80211-freq-limit = <5470000 5875000>;
+ /* Uses the reference BDF */
+ };
+ };
+};
diff --git a/target/linux/ipq40xx/files-4.19/arch/arm/boot/dts/qcom-ipq4019-fritzrepeater-3000.dts b/target/linux/ipq40xx/files-4.19/arch/arm/boot/dts/qcom-ipq4019-fritzrepeater-3000.dts
new file mode 100644
index 0000000000..744aa6a940
--- /dev/null
+++ b/target/linux/ipq40xx/files-4.19/arch/arm/boot/dts/qcom-ipq4019-fritzrepeater-3000.dts
@@ -0,0 +1,265 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+
+#include "qcom-ipq4019.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/soc/qcom,tcsr.h>
+
+/ {
+ model = "AVM FRITZ!Repeater 3000";
+ compatible = "avm,fritzrepeater-3000";
+
+ aliases {
+ led-boot = &power_led;
+ led-failsafe = &power_led;
+ led-running = &power_led;
+ led-upgrade = &power_led;
+ };
+
+ soc {
+ rng at 22000 {
+ status = "okay";
+ };
+
+ mdio at 90000 {
+ status = "okay";
+ };
+
+ ess-psgmii at 98000 {
+ status = "okay";
+ };
+
+ tcsr at 1949000 {
+ compatible = "qcom,tcsr";
+ reg = <0x1949000 0x100>;
+ qcom,wifi_glb_cfg = <TCSR_WIFI_GLB_CFG>;
+ };
+
+ ess_tcsr at 1953000 {
+ compatible = "qcom,tcsr";
+ reg = <0x1953000 0x1000>;
+ qcom,ess-interface-select = <TCSR_ESS_PSGMII>;
+ };
+
+ tcsr at 1957000 {
+ compatible = "qcom,tcsr";
+ reg = <0x1957000 0x100>;
+ qcom,wifi_noc_memtype_m0_m2 = <TCSR_WIFI_NOC_MEMTYPE_M0_M2>;
+ };
+
+ crypto at 8e3a000 {
+ status = "okay";
+ };
+
+ watchdog at b017000 {
+ status = "okay";
+ };
+
+ ess-switch at c000000 {
+ status = "okay";
+
+ switch_lan_bmp = <0x10>;
+ switch_wan_bmp = <0x20>;
+ };
+
+ edma at c080000 {
+ status = "okay";
+ };
+ };
+
+ keys {
+ compatible = "gpio-keys";
+
+ connect {
+ label = "Connect";
+ gpios = <&tlmm 10 GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_WPS_BUTTON>;
+ };
+ };
+
+ leds {
+ compatible = "gpio-leds";
+
+ connect_red {
+ label = "fritzwlan-3000:red:connect";
+ gpios = <&tlmm 30 GPIO_ACTIVE_LOW>;
+ };
+
+ connect_green {
+ label = "fritzwlan-3000:green:connect";
+ gpios = <&tlmm 31 GPIO_ACTIVE_LOW>;
+ };
+
+ connect_blue {
+ label = "fritzwlan-3000:blue:connect";
+ gpios = <&tlmm 32 GPIO_ACTIVE_LOW>;
+ };
+
+ power_led: power {
+ label = "fritzwlan-3000:green:power";
+ gpios = <&tlmm 33 GPIO_ACTIVE_LOW>;
+ };
+ };
+};
+
+&tlmm {
+ serial_0_pins: serial_pinmux {
+ mux {
+ pins = "gpio16", "gpio17";
+ function = "blsp_uart0";
+ bias-disable;
+ };
+ };
+
+ nand_pins: nand_pins {
+ pullups {
+ pins = "gpio53", "gpio58", "gpio59";
+ function = "qpic";
+ bias-pull-up;
+ };
+
+ pulldowns {
+ pins = "gpio54", "gpio55", "gpio56",
+ "gpio57", "gpio60", "gpio61",
+ "gpio62", "gpio63", "gpio64",
+ "gpio65", "gpio66", "gpio67",
+ "gpio68", "gpio69";
+ function = "qpic";
+ bias-pull-down;
+ };
+ };
+};
+
+&nand {
+ pinctrl-0 = <&nand_pins>;
+ pinctrl-names = "default";
+ status = "okay";
+ cs-gpios = <&tlmm 54 GPIO_ACTIVE_HIGH>;
+
+ nand at 0 {
+ partitions {
+ compatible = "fixed-partitions";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ partition at 0 {
+ label = "SBL1";
+ reg = <0x000000 0x80000>;
+ read-only;
+ };
+
+ partition at 80000 {
+ label = "MIBIB";
+ reg = <0x080000 0x80000>;
+ read-only;
+ };
+
+ partition at 100000 {
+ label = "QSEE";
+ reg = <0x100000 0x80000>;
+ read-only;
+ };
+
+ partition at 180000 {
+ label = "CDT";
+ reg = <0x180000 0x40000>;
+ read-only;
+ };
+
+ partition at 1c0000 {
+ label = "QSEE_B";
+ reg = <0x1c0000 0x80000>;
+ read-only;
+ };
+
+ partition at 240000 {
+ label = "urlader0";
+ reg = <0x240000 0x40000>;
+ read-only;
+ };
+
+ partition at 280000 {
+ label = "urlader1";
+ reg = <0x280000 0x40000>;
+ read-only;
+ };
+
+ partition at 2c0000 {
+ label = "nand-tffs";
+ reg = <0x2c0000 0x840000>;
+ read-only;
+ };
+
+ partition at b00000 {
+ /* 'kernel1' in AVM firmware */
+ label = "uboot0";
+ reg = <0xb00000 0x400000>;
+ };
+
+ partition at f00000 {
+ /* 'kernel2' in AVM firmware */
+ label = "uboot1";
+ reg = <0xf00000 0x400000>;
+ };
+
+ partition at 1300000 {
+ label = "ubi";
+ reg = <0x1300000 0x6d00000>;
+ };
+ };
+ };
+};
+
+&cryptobam {
+ status = "okay";
+};
+
+&blsp_dma {
+ status = "okay";
+};
+
+&blsp1_uart1 {
+ pinctrl-0 = <&serial_0_pins>;
+ pinctrl-names = "default";
+ status = "okay";
+};
+
+&qpic_bam {
+ status = "okay";
+};
+
+&wifi0 {
+ status = "okay";
+ /* BDFs are identical for the FRITZ!Box 7530 and the FRITZ!Repeater 3000 */
+ qcom,ath10k-calibration-variant = "AVM-FRITZBox-7530";
+};
+
+&wifi1 {
+ status = "okay";
+ ieee80211-freq-limit = <5170000 5350000>;
+ /* BDFs are identical for the FRITZ!Box 7530 and the FRITZ!Repeater 3000 */
+ qcom,ath10k-calibration-variant = "AVM-FRITZBox-7530";
+};
+
+&pcie0 {
+ status = "okay";
+
+ perst-gpio = <&tlmm 35 GPIO_ACTIVE_LOW>;
+ wake-gpio = <&tlmm 50 GPIO_ACTIVE_LOW>;
+
+ bridge at 0,0 {
+ reg = <0x00000000 0 0 0 0>;
+ #address-cells = <3>;
+ #size-cells = <2>;
+ ranges;
+
+ wifi at 1,0 {
+ /* QCA9984 */
+ compatible = "qcom,ath10k";
+ status = "okay";
+ reg = <0x00010000 0 0 0 0>;
+ ieee80211-freq-limit = <5470000 5875000>;
+ /* Uses the reference BDF */
+ };
+ };
+};
diff --git a/target/linux/ipq40xx/image/Makefile b/target/linux/ipq40xx/image/Makefile
index 3a7ecf39eb..e36a3a7a22 100644
--- a/target/linux/ipq40xx/image/Makefile
+++ b/target/linux/ipq40xx/image/Makefile
@@ -130,6 +130,15 @@ define Device/avm_fritzbox-7530
endef
TARGET_DEVICES += avm_fritzbox-7530
+define Device/avm_fritzrepeater-3000
+ $(call Device/FitImageLzma)
+ DEVICE_DTS := qcom-ipq4019-fritzrepeater-3000
+ DEVICE_TITLE := AVM Fritz!Repeater 3000
+ DEVICE_PACKAGES := ath10k-firmware-qca9984-ct fritz-caldata ipq-wifi-avm_fritzbox-7530
+ IMAGES := sysupgrade.bin
+endef
+TARGET_DEVICES += avm_fritzrepeater-3000
+
define Device/compex_wpj428
$(call Device/FitImage)
DEVICE_DTS := qcom-ipq4028-wpj428
diff --git a/target/linux/ipq40xx/patches-4.14/901-arm-boot-add-dts-files.patch b/target/linux/ipq40xx/patches-4.14/901-arm-boot-add-dts-files.patch
index 89ce5b1538..951479a2ef 100644
--- a/target/linux/ipq40xx/patches-4.14/901-arm-boot-add-dts-files.patch
+++ b/target/linux/ipq40xx/patches-4.14/901-arm-boot-add-dts-files.patch
@@ -10,7 +10,7 @@ Signed-off-by: John Crispin <john at phrozen.org>
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
-@@ -697,7 +697,27 @@ dtb-$(CONFIG_ARCH_QCOM) += \
+@@ -697,7 +697,28 @@ dtb-$(CONFIG_ARCH_QCOM) += \
qcom-apq8074-dragonboard.dtb \
qcom-apq8084-ifc6540.dtb \
qcom-apq8084-mtp.dtb \
@@ -29,6 +29,7 @@ Signed-off-by: John Crispin <john at phrozen.org>
+ qcom-ipq4019-a62.dtb \
+ qcom-ipq4019-ap.dk04.1-c1.dtb \
+ qcom-ipq4019-fritzbox-7530.dtb \
++ qcom-ipq4019-fritzrepeater-3000.dtb \
+ qcom-ipq4019-map-ac2200.dtb \
+ qcom-ipq4019-qxwlan-e2600ac-c1.dtb \
+ qcom-ipq4019-qxwlan-e2600ac-c2.dtb \
diff --git a/target/linux/ipq40xx/patches-4.19/901-arm-boot-add-dts-files.patch b/target/linux/ipq40xx/patches-4.19/901-arm-boot-add-dts-files.patch
index f47b7b6dab..23b3b4546a 100644
--- a/target/linux/ipq40xx/patches-4.19/901-arm-boot-add-dts-files.patch
+++ b/target/linux/ipq40xx/patches-4.19/901-arm-boot-add-dts-files.patch
@@ -10,7 +10,7 @@ Signed-off-by: John Crispin <john at phrozen.org>
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
-@@ -785,11 +785,30 @@ dtb-$(CONFIG_ARCH_QCOM) += \
+@@ -785,11 +785,31 @@ dtb-$(CONFIG_ARCH_QCOM) += \
qcom-apq8074-dragonboard.dtb \
qcom-apq8084-ifc6540.dtb \
qcom-apq8084-mtp.dtb \
@@ -32,6 +32,7 @@ Signed-off-by: John Crispin <john at phrozen.org>
qcom-ipq4019-ap.dk07.1-c2.dtb \
+ qcom-ipq4019-a62.dtb \
+ qcom-ipq4019-fritzbox-7530.dtb \
++ qcom-ipq4019-fritzrepeater-3000.dtb \
+ qcom-ipq4019-map-ac2200.dtb \
+ qcom-ipq4019-qxwlan-e2600ac-c1.dtb \
+ qcom-ipq4019-qxwlan-e2600ac-c2.dtb \
--
2.21.0
_______________________________________________
openwrt-devel mailing list
openwrt-devel at lists.openwrt.org
https://lists.openwrt.org/mailman/listinfo/openwrt-devel
More information about the openwrt-devel
mailing list