[OpenWrt-Devel] [PATCH] ath79: add support for gl-ar750

[Moritz Warning]

It would be a good idea to rewrite

DEVICE_TITLE := GL.iNet GL-AR750

to

DEVICE_VENDOR := GL.iNet
DEVICE_MODEL := GL-AR750

See https://github.com/openwrt/openwrt/pull/2124

On 7/23/19 9:45 AM, Luochongjun wrote:
> This patch supports gl-ar750, which was previously supported by ar71xx.
>
> Specification:
> - SOC: QCA9531 (650MHz)
> - Flash: 16 MiB (W25Q128FVSG)
> - RAM: 128 MiB DDR2
> - Ethernet: 10/100: 2xLAN + 10/100: 1xWAN
> - Wireless: 2.4GHz (bgn) and 5GHz (ac)
> - USB: 1x USB 2.0 port
> - Switch: 1x switch
> - Button: 1x reset button
> - LED: 3x LEDS (white)
>
> Flash instruction:
> Support for sysupgrade directive upgrades, as well as luci upgrades.
>
> Signed-off-by: Luochongjun <luochongjun at gl-inet.com>
> ---
>  .../etc/hotplug.d/firmware/11-ath10k-caldata       |   1 +
>  target/linux/ath79/dts/qca9531_glinet_gl-ar750.dts | 149 +++++++++++++++++++++
>  target/linux/ath79/image/generic.mk                |   9 ++
>  3 files changed, 159 insertions(+)
>  create mode 100644 target/linux/ath79/dts/qca9531_glinet_gl-ar750.dts
>
> diff --git a/target/linux/ath79/base-files/etc/hotplug.d/firmware/11-ath10k-caldata b/target/linux/ath79/base-files/etc/hotplug.d/firmware/11-ath10k-caldata
> index 8f0ea1d..6a9cb1c 100644
> --- a/target/linux/ath79/base-files/etc/hotplug.d/firmware/11-ath10k-caldata
> +++ b/target/linux/ath79/base-files/etc/hotplug.d/firmware/11-ath10k-caldata
> @@ -116,6 +116,7 @@ case "$FIRMWARE" in
>  		ath10kcal_extract "art" 20480 2116
>  		ath10kcal_patch_mac $(macaddr_add $(cat /sys/class/net/eth0/address) +1)
>  		;;
> +	glinet,gl-ar750|\
>  	glinet,gl-ar750s)
>  		ath10kcal_extract "art" 20480 2116
>  		ath10kcal_patch_mac $(macaddr_add $(mtd_get_mac_binary art 0) +1)
> diff --git a/target/linux/ath79/dts/qca9531_glinet_gl-ar750.dts b/target/linux/ath79/dts/qca9531_glinet_gl-ar750.dts
> new file mode 100644
> index 0000000..b8f9735
> --- /dev/null
> +++ b/target/linux/ath79/dts/qca9531_glinet_gl-ar750.dts
> @@ -0,0 +1,149 @@
> +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
> +/dts-v1/;
> +
> +#include <dt-bindings/gpio/gpio.h>
> +#include <dt-bindings/input/input.h>
> +
> +#include "qca953x.dtsi"
> +
> +/ {
> +	compatible = "glinet,gl-ar750", "qca,qca9531";
> +	model = "GL.iNet GL-AR750";
> +
> +	keys {
> +		compatible = "gpio-keys";
> +
> +		pinctrl-names = "default";
> +		pinctrl-0 = <&jtag_disable_pins>;
> +
> +		reset {
> +			label = "reset";
> +			linux,code = <KEY_RESTART>;
> +			gpios = <&gpio 3 GPIO_ACTIVE_LOW>;
> +		};
> +
> +		mode {
> +			label = "mode";
> +			linux,code = <BTN_0>;
> +			gpios = <&gpio 0 GPIO_ACTIVE_LOW>;
> +		};
> +	};
> +
> +	leds {
> +		compatible = "gpio-leds";
> +
> +		power {
> +			label = "gl-ar750:white:power";
> +			gpios = <&gpio 12 GPIO_ACTIVE_LOW>;
> +			default-state = "on";
> +		};
> +
> +		wlan2g {
> +			label = "gl-ar750:white:wlan2g";
> +			gpios = <&gpio 14 GPIO_ACTIVE_LOW>;
> +			linux,default-trigger = "phy1tpt";
> +		};
> +
> +		wlan5g {
> +			label = "gl-ar750:white:wlan5g";
> +			gpios = <&gpio 13 GPIO_ACTIVE_LOW>;
> +			linux,default-trigger = "phy0tpt";
> +		};
> +
> +	};
> +
> +	i2c {
> +		compatible = "i2c-gpio";
> +
> +		sda-gpios = <&gpio 17 GPIO_ACTIVE_LOW>;
> +		scl-gpios = <&gpio 16 GPIO_ACTIVE_LOW>;
> +	};
> +
> +
> +};
> +
> +&pcie0 {
> +	status = "okay";
> +
> +	wifi at 0,0 {
> +		compatible = "qcom,ath10k";
> +		reg = <0 0 0 0 0>;
> +		device_type = "pci";
> +	};
> +};
> +
> +&uart {
> +	status = "okay";
> +};
> +
> +&usb0 {
> +	#address-cells = <1>;
> +	#size-cells = <0>;
> +	status = "okay";
> +
> +	hub_port: port at 1 {
> +		reg = <1>;
> +		#trigger-source-cells = <0>;
> +	};
> +};
> +
> +&usb_phy {
> +	status = "okay";
> +};
> +
> +&spi {
> +	status = "okay";
> +	num-cs = <0>;
> +
> +	flash at 0 {
> +		compatible = "jedec,spi-nor";
> +		reg = <0>;
> +		spi-max-frequency = <25000000>;
> +
> +		partitions {
> +			compatible = "fixed-partitions";
> +			#address-cells = <1>;
> +			#size-cells = <1>;
> +
> +			partition at 0 {
> +				label = "u-boot";
> +				reg = <0x000000 0x040000>;
> +				read-only;
> +			};
> +
> +			partition at 40000 {
> +				label = "u-boot-env";
> +				reg = <0x040000 0x010000>;
> +				read-only;
> +			};
> +
> +			art: partition at 50000 {
> +				label = "art";
> +				reg = <0x050000 0x010000>;
> +				read-only;
> +			};
> +
> +			partition at 60000 {
> +				compatible = "denx,uimage";
> +				label = "firmware";
> +				reg = <0x060000 0xfa0000>;
> +			};
> +		};
> +	};
> +};
> +
> +&eth0 {
> +	status = "okay";
> +	mtd-mac-address = <&art 0x0>;
> +	phy-handle = <&swphy4>;
> +};
> +
> +&eth1 {
> +	mtd-mac-address = <&art 0x0>;
> +	mtd-mac-address-increment = <1>;
> +};
> +
> +&wmac {
> +	status = "okay";
> +	mtd-cal-data = <&art 0x1000>;
> +};
> diff --git a/target/linux/ath79/image/generic.mk b/target/linux/ath79/image/generic.mk
> index d5f67b8..86da1a9 100644
> --- a/target/linux/ath79/image/generic.mk
> +++ b/target/linux/ath79/image/generic.mk
> @@ -389,6 +389,15 @@ define Device/glinet_gl-ar300m-nor
>  endef
>  TARGET_DEVICES += glinet_gl-ar300m-nor
>
> +define Device/glinet_gl-ar750
> +  ATH_SOC := qca9531
> +  DEVICE_TITLE := GL.iNet GL-AR750
> +  DEVICE_PACKAGES := kmod-usb-core kmod-usb2 kmod-ath10k-ct ath10k-firmware-qca9887-ct
> +  IMAGE_SIZE := 16000k
> +  SUPPORTED_DEVICES += gl-ar750
> +endef
> +TARGET_DEVICES += glinet_gl-ar750
> +
>  define Device/glinet_gl-ar750s
>    ATH_SOC := qca9563
>    DEVICE_TITLE := GL.iNet GL-AR750S
>


_______________________________________________
openwrt-devel mailing list
openwrt-devel at lists.openwrt.org
https://lists.openwrt.org/mailman/listinfo/openwrt-devel