[OpenWrt-Devel] [PATCH] ath79: add support for Qihoo C301
Chuanhong Guo
gch981213 at gmail.com
Mon Jul 15 07:53:42 EDT 2019
Specifications:
- SoC: AR9344
- RAM: 128MB
- Flash: 2 * 16MB (MX25L12845)
- Ethernet: 2 * FE LAN & 1 * FE WAN
- WiFi: 2.4G: AR9344 5G: QCA9882
Flash instruction:
1. Hold reset and power up the router
2. Set your IP to 192.168.1.x
3. Open 192.168.1.1 and upload the generated *factory* firmware
Signed-off-by: Chuanhong Guo <gch981213 at gmail.com>
---
package/boot/uboot-envtools/files/ath79 | 3 +
.../ath79/base-files/etc/board.d/01_leds | 3 +
.../ath79/base-files/etc/board.d/02_network | 9 +
.../etc/hotplug.d/firmware/10-ath9k-eeprom | 4 +
.../etc/hotplug.d/firmware/11-ath10k-caldata | 4 +
.../ath79/base-files/etc/init.d/bootcount | 11 +
target/linux/ath79/config-4.19 | 1 +
target/linux/ath79/dts/ar9344_qihoo_c301.dts | 236 ++++++++++++++++++
target/linux/ath79/image/generic.mk | 12 +
9 files changed, 283 insertions(+)
create mode 100755 target/linux/ath79/base-files/etc/init.d/bootcount
create mode 100644 target/linux/ath79/dts/ar9344_qihoo_c301.dts
diff --git a/package/boot/uboot-envtools/files/ath79 b/package/boot/uboot-envtools/files/ath79
index 069d7be06b..cc11725242 100644
--- a/package/boot/uboot-envtools/files/ath79
+++ b/package/boot/uboot-envtools/files/ath79
@@ -29,6 +29,9 @@ openmesh,om5p-ac-v2|\
yuncore,a770)
ubootenv_add_uci_config "/dev/mtd1" "0x0" "0x10000" "0x10000"
;;
+qihoo,c301)
+ ubootenv_add_uci_config "/dev/mtd9" "0x0" "0x10000" "0x10000"
+ ;;
esac
config_load ubootenv
diff --git a/target/linux/ath79/base-files/etc/board.d/01_leds b/target/linux/ath79/base-files/etc/board.d/01_leds
index 46b3e51193..ecfb7b0694 100755
--- a/target/linux/ath79/base-files/etc/board.d/01_leds
+++ b/target/linux/ath79/base-files/etc/board.d/01_leds
@@ -104,6 +104,9 @@ pcs,cr3000)
ucidef_set_led_switch "lan3" "LAN3" "pcs:blue:lan3" "switch0" "0x10"
ucidef_set_led_switch "lan4" "LAN4" "pcs:blue:lan4" "switch0" "0x02"
;;
+qihoo,c301)
+ ucidef_set_led_wlan "wlan" "WLAN" "$boardname:green:wlan" "phy0tpt"
+ ;;
tplink,archer-a7-v5|\
tplink,archer-c7-v4|\
tplink,archer-c7-v5)
diff --git a/target/linux/ath79/base-files/etc/board.d/02_network b/target/linux/ath79/base-files/etc/board.d/02_network
index 85e57c6eb5..f7cac3e300 100755
--- a/target/linux/ath79/base-files/etc/board.d/02_network
+++ b/target/linux/ath79/base-files/etc/board.d/02_network
@@ -184,6 +184,11 @@ ath79_setup_interfaces()
ucidef_add_switch "switch0" \
"0 at eth0" "3:lan:1" "5:lan:2" "4:wan"
;;
+ qihoo,c301)
+ ucidef_set_interface_wan "eth1"
+ ucidef_add_switch "switch0" \
+ "0 at eth0" "2:lan" "3:lan"
+ ;;
rosinson,wr818)
ucidef_add_switch "switch0" \
"0 at eth0" "1:lan" "2:lan" "3:wan"
@@ -328,6 +333,10 @@ ath79_setup_macs()
lan_mac=$(k2t_get_mac "lan_mac")
wan_mac=$(k2t_get_mac "wan_mac")
;;
+ qihoo,c301)
+ lan_mac=$(mtd_get_mac_ascii devdata lanmac)
+ wan_mac=$(mtd_get_mac_ascii devdata wanmac)
+ ;;
rosinson,wr818)
wan_mac=$(mtd_get_mac_binary factory 0)
lan_mac=$(macaddr_setbit_la "$wan_mac")
diff --git a/target/linux/ath79/base-files/etc/hotplug.d/firmware/10-ath9k-eeprom b/target/linux/ath79/base-files/etc/hotplug.d/firmware/10-ath9k-eeprom
index 5a20b84344..f049dbd46a 100644
--- a/target/linux/ath79/base-files/etc/hotplug.d/firmware/10-ath9k-eeprom
+++ b/target/linux/ath79/base-files/etc/hotplug.d/firmware/10-ath9k-eeprom
@@ -127,6 +127,10 @@ case "$FIRMWARE" in
ath9k_eeprom_extract "art" 4096 1088
ath9k_patch_fw_mac $(mtd_get_mac_text board_data 1664) 2
;;
+ qihoo,c301)
+ ath9k_eeprom_extract "radiocfg" 4096 1088
+ ath9k_patch_fw_mac $(mtd_get_mac_ascii devdata "wlan24mac") 2
+ ;;
*)
ath9k_eeprom_die "board $board is not supported yet"
;;
diff --git a/target/linux/ath79/base-files/etc/hotplug.d/firmware/11-ath10k-caldata b/target/linux/ath79/base-files/etc/hotplug.d/firmware/11-ath10k-caldata
index 06a48e2258..149d744eb8 100644
--- a/target/linux/ath79/base-files/etc/hotplug.d/firmware/11-ath10k-caldata
+++ b/target/linux/ath79/base-files/etc/hotplug.d/firmware/11-ath10k-caldata
@@ -138,6 +138,10 @@ case "$FIRMWARE" in
ath10kcal_extract "art" 20480 2116
ath10kcal_patch_mac $(macaddr_add $(cat /sys/class/net/eth0/address) +16)
;;
+ qihoo,c301)
+ ath10kcal_extract "radiocfg" 20480 2116
+ ath10kcal_patch_mac_crc $(mtd_get_mac_ascii devdata wlan5mac)
+ ;;
tplink,archer-a7-v5|\
tplink,archer-c2-v3|\
tplink,archer-c7-v4|\
diff --git a/target/linux/ath79/base-files/etc/init.d/bootcount b/target/linux/ath79/base-files/etc/init.d/bootcount
new file mode 100755
index 0000000000..b71fbf9a69
--- /dev/null
+++ b/target/linux/ath79/base-files/etc/init.d/bootcount
@@ -0,0 +1,11 @@
+#!/bin/sh /etc/rc.common
+START=99
+
+boot() {
+ case $(board_name) in
+ qihoo,c301)
+ local n=$(fw_printenv activeregion | cut -d = -f 2)
+ fw_setenv "image${n}trynum" 0
+ ;;
+ esac
+}
diff --git a/target/linux/ath79/config-4.19 b/target/linux/ath79/config-4.19
index 6cdbb968c3..3843702a38 100644
--- a/target/linux/ath79/config-4.19
+++ b/target/linux/ath79/config-4.19
@@ -167,6 +167,7 @@ CONFIG_MTD_PARSER_CYBERTAN=y
CONFIG_MTD_PHYSMAP=y
CONFIG_MTD_SPI_NOR=y
CONFIG_MTD_SPLIT_LZMA_FW=y
+CONFIG_MTD_SPLIT_SEAMA_FW=y
CONFIG_MTD_SPLIT_TPLINK_FW=y
CONFIG_MTD_SPLIT_UIMAGE_FW=y
CONFIG_MTD_TPLINK_PARTS=y
diff --git a/target/linux/ath79/dts/ar9344_qihoo_c301.dts b/target/linux/ath79/dts/ar9344_qihoo_c301.dts
new file mode 100644
index 0000000000..92c4433070
--- /dev/null
+++ b/target/linux/ath79/dts/ar9344_qihoo_c301.dts
@@ -0,0 +1,236 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/dts-v1/;
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+
+#include "ar9344.dtsi"
+
+/ {
+ model = "Qihoo 360 C301";
+ compatible = "qihoo,c301";
+
+ aliases {
+ led-boot = &led_wlan_g;
+ led-failsafe = &led_wlan_o;
+ led-upgrade = &led_wlan_o;
+ };
+
+ leds {
+ compatible = "gpio-leds";
+ pinctrl-names = "default";
+ pinctrl-0 = <&jtag_disable_pins>;
+
+ led_wlan_g: wlan_g {
+ label = "c301:green:wlan";
+ gpios = <&gpio 0 GPIO_ACTIVE_LOW>;
+ };
+
+ led_wlan_o: wlan_o {
+ label = "c301:orange:wlan";
+ gpios = <&gpio 11 GPIO_ACTIVE_LOW>;
+ linux,default-trigger = "phy1tpt";
+ };
+ };
+
+ keys {
+ compatible = "gpio-keys";
+
+ reset {
+ linux,code = <KEY_RESTART>;
+ gpios = <&gpio 16 GPIO_ACTIVE_LOW>;
+ debounce-interval = <60>;
+ };
+ };
+
+ reg_eth_led_vbus {
+ compatible = "regulator-fixed";
+ regulator-name = "eth_led_vbus";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ gpio = <&gpio 18 GPIO_ACTIVE_LOW>;
+ };
+
+ reg_usb_vbus {
+ compatible = "regulator-fixed";
+ regulator-name = "usb_vbus";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ enable-active-high;
+ regulator-always-on;
+ gpio = <&gpio 19 GPIO_ACTIVE_HIGH>;
+ };
+};
+
+&pinmux {
+ pmx_spi_cs1: pinmux_spi_cs1 {
+ pinctrl-single,bits = <0xc 0x07 0xff>;
+ };
+
+ pmx_led_switch: pinmux_led_switch {
+ pinctrl-single,bits = <0x0 0x2b2a2d00 0xffffff00>;
+ };
+};
+
+&ref {
+ clock-frequency = <40000000>;
+};
+
+&uart {
+ status = "okay";
+};
+
+&gpio {
+ status = "okay";
+
+ gpio_ext_lna0 {
+ gpio-hog;
+ gpios = <14 0>;
+ output-high;
+ line-name = "c301:ext:lna0";
+ };
+
+ gpio_ext_lna1 {
+ gpio-hog;
+ gpios = <15 0>;
+ output-high;
+ line-name = "c301:ext:lna1";
+ };
+};
+
+&builtin_switch {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pmx_led_switch>;
+};
+
+&spi {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pmx_spi_cs1>;
+ status = "okay";
+
+ num-cs = <2>;
+ cs-gpios= <0>, <0>;
+
+ flash at 0 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "jedec,spi-nor";
+ reg = <0>;
+ spi-max-frequency = <25000000>;
+
+ partitions {
+ compatible = "fixed-partitions";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ uboot: partition at 0 {
+ label = "u-boot";
+ reg = <0x0 0x40000>;
+ read-only;
+ };
+
+ partition at 40000 {
+ label = "u-boot-env";
+ reg = <0x40000 0x10000>;
+ read-only;
+ };
+
+ partition at 50000 {
+ label = "devdata";
+ reg = <0x50000 0x10000>;
+ read-only;
+ };
+
+ partition at 60000 {
+ label = "devconf";
+ reg = <0x60000 0x10000>;
+ read-only;
+ };
+
+ partition at 70000 {
+ compatible = "seama";
+ label = "firmware";
+ reg = <0x70000 0xf60000>;
+ };
+
+ partition at fd0000 {
+ label = "warm_start";
+ reg = <0xfd0000 0x10000>;
+ read-only;
+ };
+
+ partition at fe0000 {
+ label = "action_image_config";
+ reg = <0xfe0000 0x10000>;
+ };
+
+ partition at ff0000 {
+ label = "radiocfg";
+ reg = <0xff0000 0x10000>;
+ read-only;
+ };
+ };
+ };
+
+ flash at 1 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "jedec,spi-nor";
+ reg = <1>;
+ spi-max-frequency = <25000000>;
+
+ partitions {
+ compatible = "fixed-partitions";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ partition at 0 {
+ label = "firmware2";
+ reg = <0x0 0xf00000>;
+ };
+
+ partition at f00000 {
+ label = "privatedata";
+ reg = <0xf00000 0x100000>;
+ read-only;
+ };
+ };
+ };
+};
+
+&usb {
+ status = "okay";
+};
+
+&usb_phy {
+ status = "okay";
+};
+
+&pcie {
+ status = "okay";
+
+ wifi at 0,0 {
+ compatible = "qcom,ath10k";
+ reg = <0 0 0 0 0>;
+ };
+};
+
+&wmac {
+ status = "okay";
+ qca,no-eeprom;
+};
+
+ð1 {
+ status = "okay";
+ gmac-config {
+ device = <&gmac>;
+ switch-phy-swap = <1>;
+ switch-only-mode = <1>;
+ };
+};
+
+ð0 {
+ status = "okay";
+ phy-handle = <&swphy0>;
+};
diff --git a/target/linux/ath79/image/generic.mk b/target/linux/ath79/image/generic.mk
index 0836751e2a..4662383541 100644
--- a/target/linux/ath79/image/generic.mk
+++ b/target/linux/ath79/image/generic.mk
@@ -728,6 +728,18 @@ define Device/phicomm_k2t
endef
TARGET_DEVICES += phicomm_k2t
+define Device/qihoo_c301
+ $(Device/seama)
+ ATH_SOC := ar9344
+ DEVICE_VENDOR := Qihoo
+ DEVICE_MODEL := C301
+ DEVICE_PACKAGES := kmod-usb2 kmod-ath10k-ct ath10k-firmware-qca988x-ct uboot-envtools
+ IMAGE_SIZE := 15744k
+ SEAMA_SIGNATURE := wrgac26_qihoo360_360rg
+ SUPPORTED_DEVICES += qihoo-c301
+endef
+TARGET_DEVICES += qihoo_c301
+
define Device/rosinson_wr818
ATH_SOC := qca9563
DEVICE_VENDOR := Rosinson
--
2.21.0
_______________________________________________
openwrt-devel mailing list
openwrt-devel at lists.openwrt.org
https://lists.openwrt.org/mailman/listinfo/openwrt-devel
More information about the openwrt-devel
mailing list