[OpenWrt-Devel] [PATCH] mpc85xx: add support for Sophos RED 15w Rev.1
Christian Lamparter
chunkeey at gmail.com
Mon Jan 7 12:15:42 EST 2019
On Sunday, January 6, 2019 5:29:54 PM CET David Bauer wrote:
> Hardware
> ========
> CPU: Freescale P1010 PowerPC
> RAM: 128M DDR3
> NAND: 128MiB
> ETH: RTL8211F SGMII PHY
> RTL8367B 5-port RGMII switch
> (not connected to SoC - unmanaged)
> WiFi: SparkLan WPEA-121N
> - Atheros AR9382 2T2R abgn
> USB: 1x USB 2.0
> LED: System, Router, Internet, Tunnel controllable
> LAN1-4, WAN, Power non-controllable
> BTN: None
>
> Installation
> ============
> 1. Power on the device while attached to the Console port.
>
> 2. Halt the U-Boot by pressing Enter when prompted.
>
> 3. Set the correct bootcmd for booting OpenWRT:
> > setenv bootargs_owrt "setenv bootargs console=ttyS0,115200"
> > setenv bootcmd "run bootargs_owrt;
> nand read 0x1000000 0x300000 0x800000;
> bootm 0x1000000;"
> > saveenv
>
> 5. Rename OpenWRT initramfs image to 'kernel.bin' and place it in a
> TFTP server root-directory served on 192.168.1.2/24. Connect your
> computer to one of the LAN-ports.
>
> 4. Boot OpenWRT initramfs image with
> > run bootargs_owrt; tftpboot 0x1000000 192.168.1.2:kernel.bin;
> bootm 0x1000000;
>
> 6. (Optional)
> Make a Backup of 'sophos-os1', 'sophos-os2' and 'sophos-data' in case
> you ever want to go back to the vendor firmware.
>
> 7. Create Ubi Volume on mtd4 by executing
> > ubiformat /dev/mtd4 -y
>
> 8. Transfer OpenWRT sysupgrade image to the device via SCP and install it
> with
> > sysupgrade -n <openwrt-image-file>
>
> Back to Stock
> =============
> If you want to go back to the stock firmware, here is the bootcmd of the
> vendor firmware:
> > setenv bootargs console=ttyS0,115200 root=/dev/mtdblock5;
> nand read 0xc00000 0x00300000 0x100000;
> nand read 0x1000000 0x00400000 0x00800000;
> bootm 0x1000000 - 0xc00000
>
> Set it via 'setenv' from the U-Boot shell and don't forget to save it
> using 'saveenv'!
>
> After this, boot the OpenWRT initramfs image just like you would for
> installation. Write back the three vendor partitions using mtd. Reboot
> the device afterwards.
>
> Signed-off-by: David Bauer <mail at david-bauer.net>
> ---
> diff --git a/target/linux/mpc85xx/config-4.14 b/target/linux/mpc85xx/config-4.14
> index 5bed475664..e81ff1cda0 100644
> --- a/target/linux/mpc85xx/config-4.14
> +++ b/target/linux/mpc85xx/config-4.14
> @@ -88,6 +88,7 @@ CONFIG_ETHERNET_PACKET_MANGLE=y
> CONFIG_FIXED_PHY=y
> # CONFIG_FORCE_SMP is not set
> CONFIG_FSL_BOOKE=y
> +# CONFIG_FSL_CORENET_CF is not set
> # CONFIG_FSL_DPAA is not set
> CONFIG_FSL_EMB_PERFMON=y
> # CONFIG_FSL_FMAN is not set
> @@ -213,7 +214,16 @@ CONFIG_MPIC_TIMER=y
> CONFIG_MPILIB=y
> # CONFIG_MTD_CFI is not set
> CONFIG_MTD_M25P80=y
> +CONFIG_MTD_NAND=y
> +CONFIG_MTD_NAND_ECC=y
> +CONFIG_MTD_NAND_FSL_IFC=y
> CONFIG_MTD_SPI_NOR=y
> +CONFIG_MTD_UBI=y
> +CONFIG_MTD_UBI_BEB_LIMIT=20
> +CONFIG_MTD_UBI_BLOCK=y
> +# CONFIG_MTD_UBI_FASTMAP is not set
> +# CONFIG_MTD_UBI_GLUEBI is not set
> +CONFIG_MTD_UBI_WL_THRESHOLD=4096
> # CONFIG_MVME2500 is not set
> # CONFIG_NEED_DMA_MAP_STATE is not set
> # CONFIG_NEED_PER_CPU_EMBED_FIRST_CHUNK is not set
> @@ -306,6 +316,8 @@ CONFIG_QUICC_ENGINE=y
> CONFIG_RAS=y
> # CONFIG_RCU_NEED_SEGCBLIST is not set
> # CONFIG_RCU_STALL_COMMON is not set
> +CONFIG_REALTEK_PHY=y
> +CONFIG_RED_15W_REV1=y
> CONFIG_REGMAP=y
> CONFIG_REGMAP_I2C=y
> CONFIG_REGMAP_SPI=y
> @@ -348,6 +360,10 @@ CONFIG_TINY_SRCU=y
> # CONFIG_TQM8555 is not set
> # CONFIG_TQM8560 is not set
> # CONFIG_TWR_P102x is not set
> +CONFIG_UBIFS_FS=y
> +CONFIG_UBIFS_FS_ADVANCED_COMPR=y
> +CONFIG_UBIFS_FS_LZO=y
> +CONFIG_UBIFS_FS_ZLIB=y
> CONFIG_UCC=y
> CONFIG_UCC_FAST=y
> CONFIG_UCC_GETH=y
Since you add this new device as a subtarget of generic, why not just add the
REALTEK_PHY, NAND, UBI + UBIFS support into target/linux/mpc85xx/generic/config-default ?
This way you won't need to patch target/linux/mpc85xx/config-4.14 and
target/linux/mpc85xx/config-4.19 as much and the HiveAP 330 does not end up
with stuff it doesn't need.
(The nand feature can also be placed into generic/target.mk)?
(However, make sure to add the
# CONFIG_RED_15W_REV1 is not set
to the config-4.14 and config-4.19)
> diff --git a/target/linux/mpc85xx/config-4.19 b/target/linux/mpc85xx/config-4.19
> index 0aaefe84ea..63cd5c6c01 100644
> --- a/target/linux/mpc85xx/config-4.19
> +++ b/target/linux/mpc85xx/config-4.19
> @@ -86,6 +86,7 @@ CONFIG_ETHERNET_PACKET_MANGLE=y
> # CONFIG_FHCI_DEBUG is not set
> CONFIG_FIXED_PHY=y
> CONFIG_FSL_BOOKE=y
> +# CONFIG_FSL_CORENET_CF is not set
> # CONFIG_FSL_DPAA is not set
> CONFIG_FSL_EMB_PERFMON=y
> # CONFIG_FSL_FMAN is not set
> @@ -199,7 +200,16 @@ CONFIG_MPIC_TIMER=y
> CONFIG_MPILIB=y
> # CONFIG_MTD_CFI is not set
> CONFIG_MTD_M25P80=y
> +CONFIG_MTD_NAND=y
> +CONFIG_MTD_NAND_ECC=y
> +CONFIG_MTD_NAND_FSL_IFC=y
> CONFIG_MTD_SPI_NOR=y
> +CONFIG_MTD_UBI=y
> +CONFIG_MTD_UBI_BEB_LIMIT=20
> +CONFIG_MTD_UBI_BLOCK=y
> +# CONFIG_MTD_UBI_FASTMAP is not set
> +# CONFIG_MTD_UBI_GLUEBI is not set
> +CONFIG_MTD_UBI_WL_THRESHOLD=4096
> # CONFIG_MVME2500 is not set
> CONFIG_NEED_PER_CPU_KM=y
> CONFIG_NEED_SG_DMA_LENGTH=y
> @@ -269,6 +279,8 @@ CONFIG_QE_GPIO=y
> CONFIG_QE_USB=y
> CONFIG_QUICC_ENGINE=y
> CONFIG_RAS=y
> +CONFIG_REALTEK_PHY=y
> +CONFIG_RED_15W_REV1=y
> CONFIG_REGMAP=y
> CONFIG_REGMAP_I2C=y
> CONFIG_REGMAP_SPI=y
> @@ -309,6 +321,10 @@ CONFIG_TINY_SRCU=y
> # CONFIG_TQM8555 is not set
> # CONFIG_TQM8560 is not set
> # CONFIG_TWR_P102x is not set
> +CONFIG_UBIFS_FS=y
> +CONFIG_UBIFS_FS_ADVANCED_COMPR=y
> +CONFIG_UBIFS_FS_LZO=y
> +CONFIG_UBIFS_FS_ZLIB=y
> CONFIG_UCC=y
> CONFIG_UCC_FAST=y
> CONFIG_UCC_GETH=y
> diff --git a/target/linux/mpc85xx/files/arch/powerpc/boot/dts/red-15w-rev1.dts b/target/linux/mpc85xx/files/arch/powerpc/boot/dts/red-15w-rev1.dts
> new file mode 100644
> index 0000000000..06b206a73d
> --- /dev/null
> +++ b/target/linux/mpc85xx/files/arch/powerpc/boot/dts/red-15w-rev1.dts
> @@ -0,0 +1,203 @@
> +// SPDX-License-Identifier: GPL-2.0-or-later or MIT
> +
> +/include/ "fsl/p1010si-pre.dtsi"
> +
> +/ {
> + model = "Sophos RED 15w Rev.1";
> + compatible = "sophos,red-15w-rev1";
> +
> + memory {
> + device_type = "memory";
> + };
> +
> + leds {
> + compatible = "gpio-leds";
> +
> + system_green {
> + gpios = <&gpio0 7 0>;
> + label = "red-15w-rev1:green:system";
> + };
> +
> + system_red {
> + gpios = <&gpio0 3 0>;
> + label = "red-15w-rev1:red:system";
> + };
> +
> + router {
> + gpios = <&gpio0 5 1>;
> + label = "red-15w-rev1:green:router";
> + };
> +
> + internet {
> + gpios = <&gpio0 4 1>;
> + label = "red-15w-rev1:green:internet";
> + };
> +
> + tunnel {
> + gpios = <&gpio0 8 1>;
> + label = "red-15w-rev1:green:tunnel";
> + };
> + };
> +
> + soc: soc at ffe00000 {
> + ranges = <0x0 0x0 0xffe00000 0x100000>;
> +
> + i2c at 3000 {
> + eeprom at 50 {
> + compatible = "st,24c256";
> + reg = <0x50>;
> + };
> + };
> +
> + i2c at 3100 {
> + eeprom at 52 {
> + compatible = "atmel,24c01";
> + reg = < 0x52 >;
> + };
> + };
> +
> + gpio0: gpio-controller at fc00 {
> + };
> +
> + usb at 22000 {
> + phy_type = "utmi";
> + dr_mode = "host";
> + };
> +
> + mdio at 24000 {
> + phy0: ethernet-phy at 0 {
> + reg = <0x0>;
> + };
> + };
> +
> + mdio at 25000 {
> + tbi_phy: tbi-phy at 11 {
> + reg = <0x11>;
> + };
> + };
> +
> + mdio at 26000 {
> + status = "disabled";
> + };
> +
> + enet0: ethernet at b0000 {
> + phy-connection-type = "rgmii-id";
> +
> + fixed-link {
> + speed = <1000>;
> + full-duplex;
> + };
> + };
> +
> + enet1: ethernet at b1000 {
> + phy-handle = <&phy0>;
> + phy-connection-type = "sgmii";
> +
> + tbi-handle = <&tbi_phy>;
> + };
> +
> + enet2: ethernet at b2000 {
> + status = "disabled";
> + };
> +
> + sdhc at 2e000 {
> + status = "disabled";
> + };
> + };
> +
> + ifc: ifc at ffe1e000 {
> + reg = <0x0 0xffe1e000 0 0x2000>;
> +
> + /* NOR, NAND Flashes and CPLD on board */
> + ranges = <0x0 0x0 0x0 0xee000000 0x02000000
> + 0x1 0x0 0x0 0xff800000 0x00010000
> + 0x3 0x0 0x0 0xffb00000 0x00000020>;
> +
> + nand at 1,0 {
> + #address-cells = <1>;
> + #size-cells = <1>;
> + compatible = "fsl,ifc-nand";
> + reg = <0x1 0x0 0x10000>;
> +
> + /*
> + * Original partition layout:
> + * 0x000000000000-0x000000100000 : "NAND U-Boot Image"
> + * 0x000000100000-0x000000200000 : "NAND U-Boot Environment"
> + * 0x000000200000-0x000000300000 : "Provisioning"
> + * - OS-Image 1
> + * 0x000000300000-0x000000400000 : "fdt1"
> + * 0x000000400000-0x000000c00000 : "uimage1"
> + * 0x000000c00000-0x000001c00000 : "rootfs1"
> + * - OS-Image 2
> + * 0x000001c00000-0x000001d00000 : "fdt2"
> + * 0x000001d00000-0x000002500000 : "uimage2"
> + * 0x000002500000-0x000003500000 : "rootfs2"
> + * - Empty
> + * 0x000003500000-0x000008000000 : "data"
> + */
> +
Does the u-boot mess with the partition in some ways? If not, can you please
move all the partitions into a partitions sub-node with "fixed-partition"
compatible? The partitions as direct subnodes of the flash device is discouraged.
<https://www.kernel.org/doc/Documentation/devicetree/bindings/mtd/partition.txt>
> + partition at 0 {
> + reg = <0x0 0x100000>;
> + label = "u-boot";
> + read-only;
> + };
> +
> + partition at 100000 {
> + reg = <0x100000 0x100000>;
> + label = "u-boot-env";
> + };
> +
> + partition at 200000 {
> + reg = <0x200000 0x100000>;
> + label = "provisioning";
> + read-only;
> + };
> +
> + partition at 300000 {
> + reg = <0x300000 0x800000>;
> + label = "kernel";
> + };
> +
> + partition at b00000 {
> + reg = <0xb00000 0x7500000>;
> + label = "ubi";
> + };
> +
> + oem-partition at 300000 {
> + reg = <0x300000 0x1900000>;
> + label = "sophos-os1";
> + };
> +
> + oem-partition at 1c00000 {
> + reg = <0x1c00000 0x1900000>;
> + label = "sophos-os2";
> + };
> +
> + oem-partition at 3500000 {
> + reg = <0x3500000 0x4b00000>;
> + label = "sophos-data";
> + };
> + };
> + };
> +
> + pci0: pcie at ffe09000 {
> + status = "disabled";
> + };
> +
> + pci1: pcie at ffe0a000 {
> + reg = <0 0xffe0a000 0 0x1000>;
> + ranges = <0x2000000 0x0 0x80000000 0 0x80000000 0x0 0x20000000
> + 0x1000000 0x0 0x00000000 0 0xffc00000 0x0 0x10000>;
> + pcie at 0 {
> + ranges = <0x2000000 0x0 0x80000000
> + 0x2000000 0x0 0x80000000
> + 0x0 0x20000000
> +
> + 0x1000000 0x0 0x0
> + 0x1000000 0x0 0x0
> + 0x0 0x100000>;
> + };
> + };
> +};
> +
> +/include/ "fsl/p1010si-post.dtsi"
> diff --git a/target/linux/mpc85xx/files/arch/powerpc/platforms/85xx/red15w_rev1.c b/target/linux/mpc85xx/files/arch/powerpc/platforms/85xx/red15w_rev1.c
> new file mode 100644
> index 0000000000..85af7dcbcb
> --- /dev/null
> +++ b/target/linux/mpc85xx/files/arch/powerpc/platforms/85xx/red15w_rev1.c
> @@ -0,0 +1,85 @@
> +/*
Just in case: can you please add a "SPDX-License-Identifier"?
"The Linux kernel requires the precise SPDX identifier in all source files."
(From Documentation/process/license-rules.rst)
> + * Sophos RED 15w Rev.1 Board Setup
> + *
> + * Copyright (C) 2019 David Bauer <mail at david-bauer.net>
> + *
> + * Based on:
> + * p1010rdb.c:
> + * P1010 RDB Board Setup
> + * Copyright 2011 Freescale Semiconductor Inc.
> + *
> + * This program is free software; you can redistribute it and/or modify it
> + * under the terms of the GNU General Public License as published by the
> + * Free Software Foundation; either version 2 of the License, or (at your
> + * option) any later version.
> + */
> +
> +#include <linux/stddef.h>
> +#include <linux/kernel.h>
> +#include <linux/delay.h>
> +#include <linux/interrupt.h>
> +#include <linux/of_platform.h>
> +
> +#include <asm/time.h>
> +#include <asm/machdep.h>
> +#include <asm/pci-bridge.h>
> +#include <mm/mmu_decl.h>
> +#include <asm/prom.h>
> +#include <asm/udbg.h>
> +#include <asm/mpic.h>
> +
> +#include <sysdev/fsl_soc.h>
> +#include <sysdev/fsl_pci.h>
> +
> +#include "mpc85xx.h"
> +
> +void __init red_15w_rev1_pic_init(void)
> +{
> + struct mpic *mpic;
> +
> + mpic = mpic_alloc(NULL, 0,
> + MPIC_BIG_ENDIAN | MPIC_SINGLE_DEST_CPU,
> + 0, 256, " OpenPIC ");
> +
> + BUG_ON(mpic == NULL);
> + mpic_init(mpic);
> +}
> +
> +/*
> + * Setup the architecture
> + */
> +static void __init red_15w_rev1_setup_arch(void)
> +{
> + if (ppc_md.progress)
> + ppc_md.progress("red_15w_rev1_setup_arch()", 0);
> +
> + fsl_pci_assign_primary();
> +
> + printk(KERN_INFO "RED 15w Rev.1 from Sophos\n");
"pr_info("...");" is the latest craze ;).
> +}
> +
> +machine_arch_initcall(red_15w_rev1, mpc85xx_common_publish_devices);
> +
> +/*
> + * Called very early, device-tree isn't unflattened
> + */
> +static int __init red_15w_rev1_probe(void)
> +{
> + if (of_machine_is_compatible("sophos,red-15w-rev1"))
> + return 1;
> + return 0;
> +}
> +
> +define_machine(red_15w_rev1) {
> + .name = "P1010 RDB",
> + .probe = red_15w_rev1_probe,
> + .setup_arch = red_15w_rev1_setup_arch,
> + .init_IRQ = red_15w_rev1_pic_init,
> +#ifdef CONFIG_PCI
> + .pcibios_fixup_bus = fsl_pcibios_fixup_bus,
> + .pcibios_fixup_phb = fsl_pcibios_fixup_phb,
> +#endif
> + .get_irq = mpic_get_irq,
> + .calibrate_decr = generic_calibrate_decr,
> + .progress = udbg_progress,
> +};
> diff --git a/target/linux/mpc85xx/image/Makefile b/target/linux/mpc85xx/image/Makefile
> index 00eed88874..0c249a5131 100644
> --- a/target/linux/mpc85xx/image/Makefile
> +++ b/target/linux/mpc85xx/image/Makefile
> @@ -57,6 +57,18 @@ define Device/tl-wdr4900-v1
> endef
> TARGET_DEVICES += tl-wdr4900-v1
>
> +define Device/red-15w-rev1
> + DEVICE_TITLE := Sophos RED 15w Rev.1
> + DEVICE_PACKAGES := kmod-usb2
> + # Original firmware uses a dedicated DTB-partition.
> + # The bootloader however supports FIT-images.
> + KERNEL = kernel-bin | gzip | fit gzip $(KDIR)/image-$$(DEVICE_DTS).dtb
> + SUPPORTED_DEVICES := sophos,red-15w-rev1
> + IMAGES := sysupgrade.bin
> + IMAGE/sysupgrade.bin := sysupgrade-tar | append-metadata
> +endef
> +TARGET_DEVICES += red-15w-rev1
> +
> endif
>
> ifeq ($(SUBTARGET),p1020)
> diff --git a/target/linux/mpc85xx/p1020/target.mk b/target/linux/mpc85xx/p1020/target.mk
> index 5d84d83205..000fc64644 100644
> --- a/target/linux/mpc85xx/p1020/target.mk
> +++ b/target/linux/mpc85xx/p1020/target.mk
> @@ -1,5 +1,4 @@
> BOARDNAME:=P1020
> -FEATURES += ramdisk
>
> define Target/Description
> Build firmware images for Freescale P1020 based boards.
> diff --git a/target/linux/mpc85xx/patches-4.14/104-powerpc-85xx-red-15w-rev1.patch b/target/linux/mpc85xx/patches-4.14/104-powerpc-85xx-red-15w-rev1.patch
> new file mode 100644
> index 0000000000..452a6cd490
> --- /dev/null
> +++ b/target/linux/mpc85xx/patches-4.14/104-powerpc-85xx-red-15w-rev1.patch
> @@ -0,0 +1,33 @@
> +Index: linux-4.14.90/arch/powerpc/platforms/85xx/Kconfig
> +===================================================================
> +--- linux-4.14.90.orig/arch/powerpc/platforms/85xx/Kconfig
> ++++ linux-4.14.90/arch/powerpc/platforms/85xx/Kconfig
> +@@ -173,6 +173,16 @@ config XES_MPC85xx
> + Manufacturer: Extreme Engineering Solutions, Inc.
> + URL: <http://www.xes-inc.com/>
> +
> ++config RED_15W_REV1
> ++ bool "Sophos RED 15w Rev.1"
> ++ select DEFAULT_UIMAGE
> ++ select ARCH_REQUIRE_GPIOLIB
> ++ select GPIO_MPC8XXX
> ++ help
> ++ This option enables support for the SOPHOS RED 15w Rev.1 board.
> ++
> ++ This board is a wireless VPN router with a Freescale P1010 SoC.
> ++
> + config STX_GP3
> + bool "Silicon Turnkey Express GP3"
> + help
> +Index: linux-4.14.90/arch/powerpc/platforms/85xx/Makefile
> +===================================================================
> +--- linux-4.14.90.orig/arch/powerpc/platforms/85xx/Makefile
> ++++ linux-4.14.90/arch/powerpc/platforms/85xx/Makefile
> +@@ -25,6 +25,7 @@ obj-$(CONFIG_P1023_RDB) += p1023_rdb.o
> + obj-$(CONFIG_TWR_P102x) += twr_p102x.o
> + obj-$(CONFIG_CORENET_GENERIC) += corenet_generic.o
> + obj-$(CONFIG_FB_FSL_DIU) += t1042rdb_diu.o
> ++obj-$(CONFIG_RED_15W_REV1) += red15w_rev1.o
> + obj-$(CONFIG_STX_GP3) += stx_gp3.o
> + obj-$(CONFIG_TQM85xx) += tqm85xx.o
> + obj-$(CONFIG_TL_WDR4900_V1) += tl_wdr4900_v1.o
> diff --git a/target/linux/mpc85xx/patches-4.19/103-powerpc-85xx-red-15w-rev1.patch b/target/linux/mpc85xx/patches-4.19/103-powerpc-85xx-red-15w-rev1.patch
> new file mode 100644
> index 0000000000..2e103fd1b3
> --- /dev/null
> +++ b/target/linux/mpc85xx/patches-4.19/103-powerpc-85xx-red-15w-rev1.patch
> @@ -0,0 +1,33 @@
> +Index: linux-4.14.90/arch/powerpc/platforms/85xx/Kconfig
> +===================================================================
> +--- linux-4.14.90.orig/arch/powerpc/platforms/85xx/Kconfig
> ++++ linux-4.14.90/arch/powerpc/platforms/85xx/Kconfig
> +@@ -173,6 +173,16 @@ config XES_MPC85xx
> + Manufacturer: Extreme Engineering Solutions, Inc.
> + URL: <http://www.xes-inc.com/>
> +
> ++config RED_15W_REV1
> ++ bool "Sophos RED 15w Rev.1"
> ++ select DEFAULT_UIMAGE
> ++ select ARCH_REQUIRE_GPIOLIB
> ++ select GPIO_MPC8XXX
> ++ help
> ++ This option enables support for the Sophos RED 15w Rev.1 board.
> ++
> ++ This board is a wireless VPN router with a Freescale P1010 SoC.
> ++
> + config STX_GP3
> + bool "Silicon Turnkey Express GP3"
> + help
> +Index: linux-4.14.90/arch/powerpc/platforms/85xx/Makefile
> +===================================================================
> +--- linux-4.14.90.orig/arch/powerpc/platforms/85xx/Makefile
> ++++ linux-4.14.90/arch/powerpc/platforms/85xx/Makefile
> +@@ -25,6 +25,7 @@ obj-$(CONFIG_P1023_RDB) += p1023_rdb.o
> + obj-$(CONFIG_TWR_P102x) += twr_p102x.o
> + obj-$(CONFIG_CORENET_GENERIC) += corenet_generic.o
> + obj-$(CONFIG_FB_FSL_DIU) += t1042rdb_diu.o
> ++obj-$(CONFIG_RED_15W_REV1) += red15w_rev1.o
> + obj-$(CONFIG_STX_GP3) += stx_gp3.o
> + obj-$(CONFIG_TQM85xx) += tqm85xx.o
> + obj-$(CONFIG_TL_WDR4900_V1) += tl_wdr4900_v1.o
_______________________________________________
openwrt-devel mailing list
openwrt-devel at lists.openwrt.org
https://lists.openwrt.org/mailman/listinfo/openwrt-devel
More information about the openwrt-devel
mailing list