[OpenWrt-Devel] [PATCH v2 3/3] ipq40xx: add support for FritzBox 7530
David Bauer
mail at david-bauer.net
Mon Feb 18 17:58:34 EST 2019
Hardware
--------
CPU: Qualcomm IPQ4019
RAM: 256M
FLASH: 128M NAND
ETH: QCA8075
VDSL: Intel/Lantiq VRX518 PCIe attached
currently not supported
DECT: Dialog SC14448
currently not supported
WiFi2: IPQ4019 2T2R 2SS b/g/n
WiFi5: IPQ4019 2T2R 2SS n/ac
LED: - Power/DSL green
- WLAN green
- FON/DECT green
- Connect/WPS green
- Info green
- Info red
BTN: - WLAN
- FON
- WPS/Connect
UART: 115200n8 3.3V (located under the Dialog chip)
VCC - RX - TX - GND (Square is VCC)
Installation
------------
1. Grab the uboot for the Device from the 'u-boot-fritz7530'
subdirectory. Place it in the same directory as the 'eva_ramboot.py'
script. It is located in the 'scripts/flashing' subdirectory of the
OpenWRT tree.
2. Assign yourself the IP address 192.168.178.10/24. Connect your
Computer to one of the boxes LAN ports.
3. Connect Power to the Box. As soon as the LAN port of your computer
shows link, load the U-Boot to the box using following command.
> ./eva_ramboot.py --offset 0x85000000 192.168.178.1 uboot-fritz7530.bin
4. The U-Boot will now start. Now assign yourself the IP address
192.168.1.70/24. Copy the OpenWRT initramfs (!) image to a TFTP
server root directory and rename it to 'FRITZ7530.bin'.
5. The Box will now boot OpenWRT from RAM. This can take up to two
minutes.
6. Copy the U-Boot and the OpenWRT sysupgrade (!) image to the Box using
scp. SSH into the Box and first write the Bootloader to both previous
kernel partitions.
> mtd write /path/to/uboot-fritz7530.bin uboot0
> mtd write /path/to/uboot-fritz7530.bin uboot1
7. Remove the AVM filesystem partitions to make room for our kernel +
rootfs + overlayfs.
> ubirmvol /dev/ubi0 --name=avm_filesys_0
> ubirmvol /dev/ubi0 --name=avm_filesys_1
8. Flash OpenWRT peristently using sysupgrade.
> sysupgrade -n /path/to/openwrt-sysupgrade.bin
Signed-off-by: David Bauer <mail at david-bauer.net>
---
v2:
- add PCIe subnode so VRX518 is detected on the PCIe bus
- driver is still missing
- add fallback onto uboot1 partition for the caldata
- adjust caldata size so no padding is extracted
- reordered 01_leds
- remove gpio52 from nand pinmux
- fixed wrong label on SBL1 partition
- drop 'qcom,ipq4019' compatible
package/boot/uboot-fritz4040/Makefile | 7 +-
package/firmware/ipq-wifi/Makefile | 3 +-
package/firmware/ipq-wifi/board-fritz7530.bin | Bin 0 -> 24324 bytes
.../ipq40xx/base-files/etc/board.d/01_leds | 7 +-
.../ipq40xx/base-files/etc/board.d/02_network | 4 +
.../etc/hotplug.d/firmware/11-ath10k-caldata | 8 +
.../base-files/lib/upgrade/platform.sh | 3 +-
.../boot/dts/qcom-ipq4019-fritzbox-7530.dts | 305 +++++++++++++++++
.../boot/dts/qcom-ipq4019-fritzbox-7530.dts | 309 ++++++++++++++++++
target/linux/ipq40xx/image/Makefile | 9 +
.../901-arm-boot-add-dts-files.patch | 3 +-
.../901-arm-boot-add-dts-files.patch | 3 +-
12 files changed, 653 insertions(+), 8 deletions(-)
create mode 100644 package/firmware/ipq-wifi/board-fritz7530.bin
create mode 100644 target/linux/ipq40xx/files-4.14/arch/arm/boot/dts/qcom-ipq4019-fritzbox-7530.dts
create mode 100644 target/linux/ipq40xx/files-4.19/arch/arm/boot/dts/qcom-ipq4019-fritzbox-7530.dts
diff --git a/package/boot/uboot-fritz4040/Makefile b/package/boot/uboot-fritz4040/Makefile
index 45f211527d..a53b7d010f 100644
--- a/package/boot/uboot-fritz4040/Makefile
+++ b/package/boot/uboot-fritz4040/Makefile
@@ -30,6 +30,11 @@ define U-Boot/fritz4040
BUILD_DEVICES:=avm_fritzbox-4040
endef
+define U-Boot/fritz7530
+ NAME:=FritzBox 7530
+ BUILD_DEVICES:=avm_fritzbox-7530
+endef
+
UBOOT_CONFIGURE_VARS += USE_PRIVATE_LIBGCC=yes
UBOOT_MAKE_FLAGS = USE_PRIVATE_LIBGCC=yes
export DTC
@@ -56,6 +61,6 @@ define Package/u-boot/install
$(INSTALL_BIN) $(PKG_BUILD_DIR)/upload-to-f4040.sh $(1)/
endef
-UBOOT_TARGETS := fritz4040
+UBOOT_TARGETS := fritz4040 fritz7530
$(eval $(call BuildPackage/U-Boot))
diff --git a/package/firmware/ipq-wifi/Makefile b/package/firmware/ipq-wifi/Makefile
index 7c9def8967..695d2f4429 100644
--- a/package/firmware/ipq-wifi/Makefile
+++ b/package/firmware/ipq-wifi/Makefile
@@ -17,7 +17,7 @@ endef
# Please send a mail with your device-specific board files upstream.
# You can find instructions and examples on the linux-wireless wiki:
# <https://wireless.wiki.kernel.org/en/users/drivers/ath10k/boardfiles>
-ALLWIFIBOARDS:=asus_map-ac2200 engenius_eap1300 linksys_ea6350v3
+ALLWIFIBOARDS:=asus_map-ac2200 engenius_eap1300 fritz7530 linksys_ea6350v3
ALLWIFIPACKAGES:=$(foreach BOARD,$(ALLWIFIBOARDS),ipq-wifi-$(BOARD))
define Package/ipq-wifi-default
@@ -54,6 +54,7 @@ endef
#$(eval $(call generate-ipq-wifi-package,<devicename>,<filename>,<displayname>))
$(eval $(call generate-ipq-wifi-package,asus_map-ac2200,board-map-ac2200.bin,ASUS MAP-AC2200))
$(eval $(call generate-ipq-wifi-package,engenius_eap1300,board-engenius_eap1300.bin,EnGenius EAP1300))
+$(eval $(call generate-ipq-wifi-package,fritz7530,board-fritz7530.bin,AVM FRITZ!Box 7530))
$(eval $(call generate-ipq-wifi-package,linksys_ea6350v3,board-linksys_ea6350v3.bin,Linksys EA6350v3))
$(foreach PACKAGE,$(ALLWIFIPACKAGES),$(eval $(call BuildPackage,$(PACKAGE))))
diff --git a/package/firmware/ipq-wifi/board-fritz7530.bin b/package/firmware/ipq-wifi/board-fritz7530.bin
new file mode 100644
index 0000000000000000000000000000000000000000..905145f1da5ee91c481f30e6bd08b3cf8da0c2ed
GIT binary patch
literal 24324
zcmeHPT~HHQ7QR9LR8%?%e<3s>;U{rPfWSzEC?P~9ffg7R5u)oNqLKhZ1m(v#CFP<b
zMr1 at 80!ENRMSgl+rCgm+nOz;%+0vA|FZ1ThzRiPFSzBAath2Y%2 at pxf1Yr%(C)~d0
zp1$XvbHDB+-F-juMOLOTvq+hgm at Aa$XBH|zO-&7eqDvsQ0A#>Yex!cO-pca$@*0hB
zU!_JT)KqLqw6w}=_tsSqO>ts;!`?d0-Y*Yt$t>P3%q~<FspYjz!qm at _6KiO23=SNR
zlQ14gqk&b&=_$p;*c%6c7bpW at jb9+q1aQkuhP6L@ITC>&nHUOy<mBXkzj*_sOkeQ!
zU*|JyWfjwr*N1H!KzsUruTC-&_yx-Q`<%BoOz#SWvmstKA#$|oGj)c;j3-=-IMZ*<
z^pG4tzNQUUg-M at naUA!di*bpOh?&hU4A>?L+gf1dmaJX7e!W``4mxuk*gl0x*D*$%
zHde9E;MMSWd%ISnQfIsx?`vzWQ0J;PKN{&f-Cn2pLbd79DAejTg{sfqLb-ic5C>k5
zjGt_;(rj1DUXAvhYOYjcD(Rz}L^ricC4mlS+Z&-RopgxX2wo43A8RgAr>WwhYisj9
zwE}j#-q#LYb0z#o<9!#Jb?QP%qSYbJKEDsNnxTB4i~VlO!5$CCt>u7{<C!fj>yv at 1
zuX41BJA*UEuGF`sR>bUJ<vtuaWXwLzuL~_Rj_xvUKFz6T?7e?kb1b)tw>?;Pf3Wsc
zdZnN=9D91R`J4RHqWXw^-;OpKx1SX at vJX7DqC1wopQ~b|JszrU&8dyu5v;gzUDKm%
z|4n0f<^A!7{)FR^I!4*jLW#=OhJcUX>b2`OAdH}pu<(dT+b8}^O?<}Ah|SBch8IKt
z&}d#>UNmC6YL$<VkFQnyhC7?el+R8S at R`xkJop#Gjf&!Nqqy8+Z+~FDLa`f-YAh-O
zot+I0MMYS)1gu at _>q~}`2x53#ZX|3l{r>az-Mb*Dkv75 at 5#Z<L?fqX%R~m5SPmZ#9
zTiqDE9)ZK_j(3a^g^0wrN^CSCTuwxAY&4h4LD{TOsLkI7J$XDHF%TTpI^M_F9HD}s
z2$G3rB1vcxqC0Z*c<Y&tuAaFHkXq$|TM8Yei|Ehk2n%J2SXdw$h=ihYR4$S~mm at i7
zjwlC{p)y2?iczsh{9KHrp=qKtED=paB<OS!ra{N*bWT#~bXJr)=lHk+2?J%kW+35c
zxF{UULbG0HA-QO-C>KjclV2wz>1etr9U~9I?5!mf3H_pPiE~$X#xyp&#C)X8e6u*#
z9KB!WYg-Q2q|_W-Ir<bz6iQAIpiT`Zz}T5rBuaJ&Pz?$J3IPfM3IPfM3V{`jK!`X5
ziKKrn{v64tr;1aN47$HfKw<fX!P}2#Z*8~!?$vW+thUL5#aO|Iked2(LBQ1&0$2Mj
zF<h|Sm4=BI0KmG*Ffj4r{Te>0hR>)`b{Lb#<B$)(q2 at U@E)+|Cp%#UBIM4JXTND&d
zB*ZTSDzGN<^CX+6pRO1E5Fkqdz(7Z6!B9G_^+jvV_eX#fNWEnM0e^oiXaOJz at DRwO
zg2Wpx<n!2y6x!uJf|qhX!9QRjYD)?9Mu1<74`&$efA#Wb at Y7E}TWUfl3MI=IfnRO~
zFulAg;0go)G%s)eZ=hU-Vw>?jC?8|PO5lg<z{HQv>bTgL=ucV5l{<2+j$EC?3W`d0
zmsM06IxqHI9vB)PyESp|;a`6E at rC<4X07A7cjdZddIQTkC`NCyt%O?EKrwlnZ57nA
z{)vg(Y%8GdgXq*_`J=mJPJ`u at s4Hv6dBuAUbaY?2j^Ca9n=^fRp)xZY<~t_BM%f}Z
z#srFY3Iszj5r!#1%DWUqib_RNEM>v&uV<pVqXmnD5tN=S&PMX+o5Y)tt#oxS at tQk^
z?R(BvFO^#ycX{_oF7fWMZW;}e?wdL-Ebt&J?>@+nL<e3{@(A8N0N&oD#eU2C?OfhH
z<R4_%%6xhEFv|D#kpNg|-aU~c5d*ag<e2|H!>70FJf|_!&jsGSowwt-?(psbgTZiE
z*lac+N<ct>J7x9i#pK<~m;=n04*$o&4i=}4(a}+-`{wR|$9k5`-S4VpMK0%3lXm6w
z at IaJYNt^0JAwVHOA+S^tC at WJJle~L6J#Za43paW9Wu*VQbzW~s{{shXW3pKAnrgv?
z;@w;C${yJ6&VEgyc=yxjxI%xoLHd91>&i2f*^GNqx1>u>aM8EK8+kV8p3py%b{~V4
z5D&W_zL<4;VW)oR!(-}<xf;hzNe1>*o4E?lHHi%olXp$s`a`AJl9<Wc_>e)bEtRl|
z{}sF36UPTrUFK$7ZIT&;Q<uzoe3waXNWdpd16plqo+N(q&!!9dno_xhLpYd>adBX(
z*L)H`Xeuylnd!K+O>^g{ewL$|h0sgQ`FLzlkV=5WOrCjhY9Ib3Hb)NY!(X70k9
z3?*7AK56LF9#(GShgu?3X?Kw+nR<zoOy+jHO0Ou5o*Fct$LkC`v|I7-3`T8(QppdW
zyl1*(Nhy*@=}IpjM(8pB0pF+Js$@aeHe92ZE5q?WnfkRg%1lXu`8#~j(5&4lVG$1f
zy at FUU)opIU%k*i=uqmUt6|c}sm0>Uuqy9)~u0&wIi}xDpwE4<tGJ*i6bl%*Am*~Yx
z=G52bqqrJsi1|K#6=Erqps(&sUN$vqvy@?E1ULtG!~-w&sgztffD}p;N=^`14yT5b
zsZr(?i@@D8$9}ghNyrZKz1CK}J5?MNvEKi1cXq4b5UV^O`}?8&=eFp12SZB#+SR1a
z5XJ_D`rNs6tSUz?P6!V at KTzC}bd;mrkoWXv^#xf=OikFHXT6$&)VSCX03P)ptyX4<
zgb at +<h7WbiP6+DgJ06c{x-wdL)uDTy^w*ckH^s0+10GzfKB!cp+(3q*FYjd1;h>%C
zw%xy3ej)8Rrz&XILsRwc0!4f@;yp3gP`6FV<p;6ajrpfi8bV70ly^pde at Sv8vL<NH
zM9<-Us;%)nhVO`}p<acFB|+g6{dFB#$Kq>(3!nWl=WKj)*nz;Ex4MsN^A!Rv-FL`X
z`(;6qFeRLO!>DQ7dSv54M(*|D+TQe5ULAAKjq|#4MLLhoX7+wvv42}myf}z;u4Cs{
zDO&C>y6pBy{pGxK{KnAzEB3^pCQc!+3=sI(U*YhZEe`M)XwxYrO=_u_9}^P||KKlh
zaClKs+^Aw7kNFjjxtw?#?cRUE*6ioTu+i>UFIWr*@KYuVf%zfeD(PdP`^_)gW#dKh
z?ja|B5jp#w#Ibjji>IH+!;nu;^4}2)ho0cquW1#uC?HRM<7RFqSt1W at +-xaV1HF?h
zJbHpl at 7J;h7NYjySa|mY*WO3)PYeH^<lw*b^!cyk{0LsWH{`{a^bG&77`*t!#?~3%
z-e&)loO>cR#k-$bnwy74@$TmV8s*~I2)MFl?2Kza+wR%3oPTx{?|!krHGh5l{{g(;
Bh^qhq
literal 0
HcmV?d00001
diff --git a/target/linux/ipq40xx/base-files/etc/board.d/01_leds b/target/linux/ipq40xx/base-files/etc/board.d/01_leds
index 9105bf2452..ec8486aa95 100755
--- a/target/linux/ipq40xx/base-files/etc/board.d/01_leds
+++ b/target/linux/ipq40xx/base-files/etc/board.d/01_leds
@@ -22,15 +22,16 @@ avm,fritzbox-4040)
ucidef_set_led_netdev "wan" "WAN" "fritz4040:green:wan" "eth1"
ucidef_set_led_switch "lan" "LAN" "fritz4040:green:lan" "switch0" "0x1e"
;;
+avm,fritzbox-7530 |\
+glinet,gl-b1300)
+ ucidef_set_led_wlan "wlan" "WLAN" "${boardname}:green:wlan" "phy0tpt"
+ ;;
engenius,eap1300)
ucidef_set_led_netdev "lan" "LAN" "${boardname}:blue:lan" "eth0"
ucidef_set_led_wlan "wlan2g" "WLAN2G" "${boardname}:blue:wlan2g" "phy0tpt"
ucidef_set_led_wlan "wlan5g" "WLAN5G" "${boardname}:yellow:wlan5g" "phy1tpt"
ucidef_set_led_default "mesh" "MESH" "${boardname}:blue:mesh" "0"
;;
-glinet,gl-b1300)
- ucidef_set_led_wlan "wlan" "WLAN" "${boardname}:green:wlan" "phy0tpt"
- ;;
netgear,ex6100v2 |\
netgear,ex6150v2)
ucidef_set_led_wlan "wlan2g" "WLAN2G" "ex61x0v2:green:router" "phy0tpt"
diff --git a/target/linux/ipq40xx/base-files/etc/board.d/02_network b/target/linux/ipq40xx/base-files/etc/board.d/02_network
index 43be592071..2fd3d76ed0 100755
--- a/target/linux/ipq40xx/base-files/etc/board.d/02_network
+++ b/target/linux/ipq40xx/base-files/etc/board.d/02_network
@@ -32,6 +32,10 @@ ipq40xx_setup_interfaces()
ucidef_add_switch "switch0" \
"0u at eth0" "1:lan" "2:lan" "3:lan" "4:lan"
;;
+ avm,fritzbox-7530)
+ ucidef_add_switch "switch0" \
+ "0u at eth0" "1:lan" "2:lan" "3:lan" "4:lan"
+ ;;
compex,wpj428)
ucidef_set_interface_lan "eth0 eth1"
;;
diff --git a/target/linux/ipq40xx/base-files/etc/hotplug.d/firmware/11-ath10k-caldata b/target/linux/ipq40xx/base-files/etc/hotplug.d/firmware/11-ath10k-caldata
index 59a809e792..d9d362598d 100644
--- a/target/linux/ipq40xx/base-files/etc/hotplug.d/firmware/11-ath10k-caldata
+++ b/target/linux/ipq40xx/base-files/etc/hotplug.d/firmware/11-ath10k-caldata
@@ -134,6 +134,10 @@ case "$FIRMWARE" in
avm,fritzbox-4040)
/usr/bin/fritz_cal_extract -i 1 -s 0x400 -e 0x207 -l 12064 -o /lib/firmware/$FIRMWARE $(find_mtd_chardev "urlader_config")
;;
+ avm,fritzbox-7530)
+ /usr/bin/fritz_cal_extract -i 1 -s 0x3C000 -e 0x207 -l 12064 -o /lib/firmware/$FIRMWARE $(find_mtd_chardev "urlader0") || \
+ /usr/bin/fritz_cal_extract -i 1 -s 0x3C000 -e 0x207 -l 12064 -o /lib/firmware/$FIRMWARE $(find_mtd_chardev "urlader1")
+ ;;
meraki,mr33)
ath10kcal_ubi_extract "ART" 4096 12064
ath10kcal_is_caldata_valid "202f" || ath10kcal_extract "ART" 4096 12064
@@ -175,6 +179,10 @@ case "$FIRMWARE" in
avm,fritzbox-4040)
/usr/bin/fritz_cal_extract -i 1 -s 0x400 -e 0x208 -l 12064 -o /lib/firmware/$FIRMWARE $(find_mtd_chardev "urlader_config")
;;
+ avm,fritzbox-7530)
+ /usr/bin/fritz_cal_extract -i 1 -s 0x3C800 -e 0x208 -l 12064 -o /lib/firmware/$FIRMWARE $(find_mtd_chardev "urlader0") || \
+ /usr/bin/fritz_cal_extract -i 1 -s 0x3C800 -e 0x208 -l 12064 -o /lib/firmware/$FIRMWARE $(find_mtd_chardev "urlader1")
+ ;;
meraki,mr33)
ath10kcal_ubi_extract "ART" 20480 12064
ath10kcal_is_caldata_valid "202f" || ath10kcal_extract "ART" 20480 12064
diff --git a/target/linux/ipq40xx/base-files/lib/upgrade/platform.sh b/target/linux/ipq40xx/base-files/lib/upgrade/platform.sh
index f6bc173a76..eb1c64aa49 100644
--- a/target/linux/ipq40xx/base-files/lib/upgrade/platform.sh
+++ b/target/linux/ipq40xx/base-files/lib/upgrade/platform.sh
@@ -46,7 +46,8 @@ zyxel_do_upgrade() {
platform_do_upgrade() {
case "$(board_name)" in
- 8dev,jalapeno)
+ 8dev,jalapeno|\
+ avm,fritzbox-7530)
nand_do_upgrade "$ARGV"
;;
asus,map-ac2200)
diff --git a/target/linux/ipq40xx/files-4.14/arch/arm/boot/dts/qcom-ipq4019-fritzbox-7530.dts b/target/linux/ipq40xx/files-4.14/arch/arm/boot/dts/qcom-ipq4019-fritzbox-7530.dts
new file mode 100644
index 0000000000..b2a33468bb
--- /dev/null
+++ b/target/linux/ipq40xx/files-4.14/arch/arm/boot/dts/qcom-ipq4019-fritzbox-7530.dts
@@ -0,0 +1,305 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+
+#include "qcom-ipq4019.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/soc/qcom,tcsr.h>
+
+/ {
+ model = "AVM FRITZ!Box 7530";
+ compatible = "avm,fritzbox-7530";
+
+ aliases {
+ led-boot = &power_green;
+ led-failsafe = &info_red;
+ led-running = &power_green;
+ led-upgrade = &info_green;
+ };
+
+ soc {
+ mdio at 90000 {
+ status = "okay";
+ };
+
+ ess-psgmii at 98000 {
+ status = "okay";
+ };
+
+ tcsr at 1949000 {
+ compatible = "qcom,tcsr";
+ reg = <0x1949000 0x100>;
+ qcom,wifi_glb_cfg = <TCSR_WIFI_GLB_CFG>;
+ };
+
+ tcsr at 194b000 {
+ compatible = "qcom,tcsr";
+ reg = <0x194b000 0x100>;
+ qcom,usb-hsphy-mode-select = <TCSR_USB_HSPHY_HOST_MODE>;
+ };
+
+ ess_tcsr at 1953000 {
+ compatible = "qcom,tcsr";
+ reg = <0x1953000 0x1000>;
+ qcom,ess-interface-select = <TCSR_ESS_PSGMII>;
+ };
+
+ tcsr at 1957000 {
+ compatible = "qcom,tcsr";
+ reg = <0x1957000 0x100>;
+ qcom,wifi_noc_memtype_m0_m2 = <TCSR_WIFI_NOC_MEMTYPE_M0_M2>;
+ };
+
+ usb3 at 8af8800 {
+ status = "okay";
+ };
+
+ crypto at 8e3a000 {
+ status = "okay";
+ };
+
+ watchdog at b017000 {
+ status = "okay";
+ };
+
+ ess-switch at c000000 {
+ status = "okay";
+ };
+
+ edma at c080000 {
+ status = "okay";
+ qcom,num_gmac = <1>;
+ };
+ };
+
+ keys {
+ compatible = "gpio-keys";
+
+ wlan {
+ label = "wlan";
+ gpios = <&tlmm 42 GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_RFKILL>;
+ };
+
+ wps {
+ label = "wps";
+ gpios = <&tlmm 41 GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_WPS_BUTTON>;
+ };
+
+ dect {
+ label = "dect";
+ gpios = <&tlmm 43 GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_PHONE>;
+ };
+ };
+
+ leds {
+ compatible = "gpio-leds";
+
+ info_red: info_red {
+ label = "fritzbox-7530:red:info";
+ gpios = <&tlmm 32 GPIO_ACTIVE_LOW>;
+ };
+
+ info_green: info {
+ label = "fritzbox-7530:green:info";
+ gpios = <&tlmm 33 GPIO_ACTIVE_LOW>;
+ };
+
+ wlan {
+ label = "fritzbox-7530:green:wlan";
+ gpios = <&tlmm 34 GPIO_ACTIVE_LOW>;
+ };
+
+ fon {
+ label = "fritzbox-7530:green:fon";
+ gpios = <&tlmm 35 GPIO_ACTIVE_LOW>;
+ };
+
+ power_green: power {
+ label = "fritzbox-7530:green:power";
+ gpios = <&tlmm 39 GPIO_ACTIVE_LOW>;
+ };
+
+ wps {
+ label = "fritzbox-7530:green:wps";
+ gpios = <&tlmm 45 GPIO_ACTIVE_LOW>;
+ };
+ };
+};
+
+&tlmm {
+ serial_0_pins: serial_pinmux {
+ mux {
+ pins = "gpio16", "gpio17";
+ function = "blsp_uart0";
+ bias-disable;
+ };
+ };
+
+ nand_pins: nand_pins {
+ pullups {
+ pins = "gpio53", "gpio58", "gpio59";
+ function = "qpic";
+ bias-pull-up;
+ };
+
+ pulldowns {
+ pins = "gpio54", "gpio55", "gpio56",
+ "gpio57", "gpio60", "gpio61",
+ "gpio62", "gpio63", "gpio64",
+ "gpio65", "gpio66", "gpio67",
+ "gpio68", "gpio69";
+ function = "qpic";
+ bias-pull-down;
+ };
+ };
+
+ usb-power {
+ line-name = "enable USB3 power";
+ gpios = <49 GPIO_ACTIVE_HIGH>;
+ gpio-hog;
+ output-high;
+ };
+};
+
+&nand {
+ pinctrl-0 = <&nand_pins>;
+ pinctrl-names = "default";
+ status = "okay";
+ cs-gpios = <&tlmm 54 GPIO_ACTIVE_HIGH>;
+
+ nand at 0 {
+ partitions {
+ compatible = "fixed-partitions";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ partition at 0 {
+ label = "SBL1";
+ reg = <0x000000 0x80000>;
+ read-only;
+ };
+
+ partition at 80000 {
+ label = "MIBIB";
+ reg = <0x080000 0x80000>;
+ read-only;
+ };
+
+ partition at 100000 {
+ label = "QSEE";
+ reg = <0x100000 0x80000>;
+ read-only;
+ };
+
+ partition at 180000 {
+ label = "CDT";
+ reg = <0x180000 0x40000>;
+ read-only;
+ };
+
+ partition at 1c0000 {
+ label = "QSEE_B";
+ reg = <0x1c0000 0x80000>;
+ read-only;
+ };
+
+ partition at 240000 {
+ label = "urlader0";
+ reg = <0x240000 0x40000>;
+ read-only;
+ };
+
+ partition at 280000 {
+ label = "urlader1";
+ reg = <0x280000 0x40000>;
+ read-only;
+ };
+
+ partition at 2c0000 {
+ label = "nand-tffs";
+ reg = <0x2c0000 0x840000>;
+ read-only;
+ };
+
+ partition at b00000 {
+ /* 'kernel1' in AVM firmware */
+ label = "uboot0";
+ reg = <0xb00000 0x400000>;
+ };
+
+ partition at f00000 {
+ /* 'kernel2' in AVM firmware */
+ label = "uboot1";
+ reg = <0xf00000 0x400000>;
+ };
+
+ partition at 1300000 {
+ label = "ubi";
+ reg = <0x1300000 0x6d00000>;
+ };
+ };
+ };
+};
+
+&cryptobam {
+ status = "okay";
+};
+
+&blsp_dma {
+ status = "okay";
+};
+
+&blsp1_uart1 {
+ pinctrl-0 = <&serial_0_pins>;
+ pinctrl-names = "default";
+ status = "okay";
+};
+
+&usb3_ss_phy {
+ status = "okay";
+};
+
+&usb3_hs_phy {
+ status = "okay";
+};
+
+&qpic_bam {
+ status = "okay";
+};
+
+&wifi0 {
+ status = "okay";
+ qcom,ath10k-calibration-variant = "AVM-FRITZBox-7530";
+};
+
+&wifi1 {
+ status = "okay";
+ qcom,ath10k-calibration-variant = "AVM-FRITZBox-7530";
+};
+
+&pcie0 {
+ status = "okay";
+
+ ranges = <0x81000000 0 0x40200000 0x40200000
+ 0 0x00100000 /* downstream I/O */
+ 0x82000000 0 0x48000000 0x48000000
+ 0 0x10000000>; /* non-prefetchable memory */
+
+ perst-gpio = <&tlmm 38 GPIO_ACTIVE_LOW>;
+ wake-gpio = <&tlmm 50 GPIO_ACTIVE_LOW>;
+
+ bridge at 0,0 {
+ reg = <0x00000000 0 0 0 0>;
+ #address-cells = <3>;
+ #size-cells = <2>;
+ ranges;
+
+ dsl at 1,0 {
+ compatible = "intel,vrx518";
+ status = "okay";
+ reg = <0x00010000 0 0 0 0>;
+ };
+ };
+};
diff --git a/target/linux/ipq40xx/files-4.19/arch/arm/boot/dts/qcom-ipq4019-fritzbox-7530.dts b/target/linux/ipq40xx/files-4.19/arch/arm/boot/dts/qcom-ipq4019-fritzbox-7530.dts
new file mode 100644
index 0000000000..7dacf0ad90
--- /dev/null
+++ b/target/linux/ipq40xx/files-4.19/arch/arm/boot/dts/qcom-ipq4019-fritzbox-7530.dts
@@ -0,0 +1,309 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+
+#include "qcom-ipq4019.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/soc/qcom,tcsr.h>
+
+/ {
+ model = "AVM FRITZ!Box 7530";
+ compatible = "avm,fritzbox-7530";
+
+ aliases {
+ led-boot = &power_green;
+ led-failsafe = &info_red;
+ led-running = &power_green;
+ led-upgrade = &info_green;
+ };
+
+ soc {
+ rng at 22000 {
+ status = "okay";
+ };
+
+ mdio at 90000 {
+ status = "okay";
+ };
+
+ ess-psgmii at 98000 {
+ status = "okay";
+ };
+
+ tcsr at 1949000 {
+ compatible = "qcom,tcsr";
+ reg = <0x1949000 0x100>;
+ qcom,wifi_glb_cfg = <TCSR_WIFI_GLB_CFG>;
+ };
+
+ tcsr at 194b000 {
+ compatible = "qcom,tcsr";
+ reg = <0x194b000 0x100>;
+ qcom,usb-hsphy-mode-select = <TCSR_USB_HSPHY_HOST_MODE>;
+ };
+
+ ess_tcsr at 1953000 {
+ compatible = "qcom,tcsr";
+ reg = <0x1953000 0x1000>;
+ qcom,ess-interface-select = <TCSR_ESS_PSGMII>;
+ };
+
+ tcsr at 1957000 {
+ compatible = "qcom,tcsr";
+ reg = <0x1957000 0x100>;
+ qcom,wifi_noc_memtype_m0_m2 = <TCSR_WIFI_NOC_MEMTYPE_M0_M2>;
+ };
+
+ usb3 at 8af8800 {
+ status = "okay";
+ };
+
+ crypto at 8e3a000 {
+ status = "okay";
+ };
+
+ watchdog at b017000 {
+ status = "okay";
+ };
+
+ ess-switch at c000000 {
+ status = "okay";
+ };
+
+ edma at c080000 {
+ status = "okay";
+ qcom,num_gmac = <1>;
+ };
+ };
+
+ keys {
+ compatible = "gpio-keys";
+
+ wlan {
+ label = "wlan";
+ gpios = <&tlmm 42 GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_RFKILL>;
+ };
+
+ wps {
+ label = "wps";
+ gpios = <&tlmm 41 GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_WPS_BUTTON>;
+ };
+
+ dect {
+ label = "dect";
+ gpios = <&tlmm 43 GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_PHONE>;
+ };
+ };
+
+ leds {
+ compatible = "gpio-leds";
+
+ info_red: info_red {
+ label = "fritzbox-7530:red:info";
+ gpios = <&tlmm 32 GPIO_ACTIVE_LOW>;
+ };
+
+ info_green: info {
+ label = "fritzbox-7530:green:info";
+ gpios = <&tlmm 33 GPIO_ACTIVE_LOW>;
+ };
+
+ wlan {
+ label = "fritzbox-7530:green:wlan";
+ gpios = <&tlmm 34 GPIO_ACTIVE_LOW>;
+ };
+
+ fon {
+ label = "fritzbox-7530:green:fon";
+ gpios = <&tlmm 35 GPIO_ACTIVE_LOW>;
+ };
+
+ power_green: power {
+ label = "fritzbox-7530:green:power";
+ gpios = <&tlmm 39 GPIO_ACTIVE_LOW>;
+ };
+
+ wps {
+ label = "fritzbox-7530:green:wps";
+ gpios = <&tlmm 45 GPIO_ACTIVE_LOW>;
+ };
+ };
+};
+
+&tlmm {
+ serial_0_pins: serial_pinmux {
+ mux {
+ pins = "gpio16", "gpio17";
+ function = "blsp_uart0";
+ bias-disable;
+ };
+ };
+
+ nand_pins: nand_pins {
+ pullups {
+ pins = "gpio53", "gpio58", "gpio59";
+ function = "qpic";
+ bias-pull-up;
+ };
+
+ pulldowns {
+ pins = "gpio54", "gpio55", "gpio56",
+ "gpio57", "gpio60", "gpio61",
+ "gpio62", "gpio63", "gpio64",
+ "gpio65", "gpio66", "gpio67",
+ "gpio68", "gpio69";
+ function = "qpic";
+ bias-pull-down;
+ };
+ };
+
+ usb-power {
+ line-name = "enable USB3 power";
+ gpios = <49 GPIO_ACTIVE_HIGH>;
+ gpio-hog;
+ output-high;
+ };
+};
+
+&nand {
+ pinctrl-0 = <&nand_pins>;
+ pinctrl-names = "default";
+ status = "okay";
+ cs-gpios = <&tlmm 54 GPIO_ACTIVE_HIGH>;
+
+ nand at 0 {
+ partitions {
+ compatible = "fixed-partitions";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ partition at 0 {
+ label = "SBL1";
+ reg = <0x000000 0x80000>;
+ read-only;
+ };
+
+ partition at 80000 {
+ label = "MIBIB";
+ reg = <0x080000 0x80000>;
+ read-only;
+ };
+
+ partition at 100000 {
+ label = "QSEE";
+ reg = <0x100000 0x80000>;
+ read-only;
+ };
+
+ partition at 180000 {
+ label = "CDT";
+ reg = <0x180000 0x40000>;
+ read-only;
+ };
+
+ partition at 1c0000 {
+ label = "QSEE_B";
+ reg = <0x1c0000 0x80000>;
+ read-only;
+ };
+
+ partition at 240000 {
+ label = "urlader0";
+ reg = <0x240000 0x40000>;
+ read-only;
+ };
+
+ partition at 280000 {
+ label = "urlader1";
+ reg = <0x280000 0x40000>;
+ read-only;
+ };
+
+ partition at 2c0000 {
+ label = "nand-tffs";
+ reg = <0x2c0000 0x840000>;
+ read-only;
+ };
+
+ partition at b00000 {
+ /* 'kernel1' in AVM firmware */
+ label = "uboot0";
+ reg = <0xb00000 0x400000>;
+ };
+
+ partition at f00000 {
+ /* 'kernel2' in AVM firmware */
+ label = "uboot1";
+ reg = <0xf00000 0x400000>;
+ };
+
+ partition at 1300000 {
+ label = "ubi";
+ reg = <0x1300000 0x6d00000>;
+ };
+ };
+ };
+};
+
+&cryptobam {
+ status = "okay";
+};
+
+&blsp_dma {
+ status = "okay";
+};
+
+&blsp1_uart1 {
+ pinctrl-0 = <&serial_0_pins>;
+ pinctrl-names = "default";
+ status = "okay";
+};
+
+&usb3_ss_phy {
+ status = "okay";
+};
+
+&usb3_hs_phy {
+ status = "okay";
+};
+
+&qpic_bam {
+ status = "okay";
+};
+
+&wifi0 {
+ status = "okay";
+ qcom,ath10k-calibration-variant = "AVM-FRITZBox-7530";
+};
+
+&wifi1 {
+ status = "okay";
+ qcom,ath10k-calibration-variant = "AVM-FRITZBox-7530";
+};
+
+&pcie0 {
+ status = "okay";
+
+ ranges = <0x81000000 0 0x40200000 0x40200000
+ 0 0x00100000 /* downstream I/O */
+ 0x82000000 0 0x48000000 0x48000000
+ 0 0x10000000>; /* non-prefetchable memory */
+
+ perst-gpio = <&tlmm 38 GPIO_ACTIVE_LOW>;
+ wake-gpio = <&tlmm 50 GPIO_ACTIVE_LOW>;
+
+ bridge at 0,0 {
+ reg = <0x00000000 0 0 0 0>;
+ #address-cells = <3>;
+ #size-cells = <2>;
+ ranges;
+
+ dsl at 1,0 {
+ compatible = "intel,vrx518";
+ status = "okay";
+ reg = <0x00010000 0 0 0 0>;
+ };
+ };
+};
diff --git a/target/linux/ipq40xx/image/Makefile b/target/linux/ipq40xx/image/Makefile
index 31468fd758..4b42ca1241 100644
--- a/target/linux/ipq40xx/image/Makefile
+++ b/target/linux/ipq40xx/image/Makefile
@@ -106,6 +106,15 @@ define Device/avm_fritzbox-4040
endef
TARGET_DEVICES += avm_fritzbox-4040
+define Device/avm_fritzbox-7530
+ $(call Device/FitImageLzma)
+ DEVICE_DTS := qcom-ipq4019-fritzbox-7530
+ DEVICE_TITLE := AVM Fritz!Box 7530
+ DEVICE_PACKAGES := fritz-caldata ipq-wifi-fritz7530
+ IMAGES := sysupgrade.bin
+endef
+TARGET_DEVICES += avm_fritzbox-7530
+
define Device/compex_wpj428
$(call Device/FitImage)
DEVICE_DTS := qcom-ipq4028-wpj428
diff --git a/target/linux/ipq40xx/patches-4.14/901-arm-boot-add-dts-files.patch b/target/linux/ipq40xx/patches-4.14/901-arm-boot-add-dts-files.patch
index 20ea3a8449..a528743b69 100644
--- a/target/linux/ipq40xx/patches-4.14/901-arm-boot-add-dts-files.patch
+++ b/target/linux/ipq40xx/patches-4.14/901-arm-boot-add-dts-files.patch
@@ -10,7 +10,7 @@ Signed-off-by: John Crispin <john at phrozen.org>
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
-@@ -697,7 +697,23 @@ dtb-$(CONFIG_ARCH_QCOM) += \
+@@ -697,7 +697,24 @@ dtb-$(CONFIG_ARCH_QCOM) += \
qcom-apq8074-dragonboard.dtb \
qcom-apq8084-ifc6540.dtb \
qcom-apq8084-mtp.dtb \
@@ -27,6 +27,7 @@ Signed-off-by: John Crispin <john at phrozen.org>
qcom-ipq4019-ap.dk01.1-c1.dtb \
+ qcom-ipq4019-a62.dtb \
+ qcom-ipq4019-ap.dk04.1-c1.dtb \
++ qcom-ipq4019-fritzbox-7530.dtb \
+ qcom-ipq4019-map-ac2200.dtb \
+ qcom-ipq4028-wpj428.dtb \
+ qcom-ipq4029-gl-b1300.dtb \
diff --git a/target/linux/ipq40xx/patches-4.19/901-arm-boot-add-dts-files.patch b/target/linux/ipq40xx/patches-4.19/901-arm-boot-add-dts-files.patch
index f3472b32c0..050779e5a0 100644
--- a/target/linux/ipq40xx/patches-4.19/901-arm-boot-add-dts-files.patch
+++ b/target/linux/ipq40xx/patches-4.19/901-arm-boot-add-dts-files.patch
@@ -10,7 +10,7 @@ Signed-off-by: John Crispin <john at phrozen.org>
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
-@@ -785,11 +785,26 @@ dtb-$(CONFIG_ARCH_QCOM) += \
+@@ -785,11 +785,27 @@ dtb-$(CONFIG_ARCH_QCOM) += \
qcom-apq8074-dragonboard.dtb \
qcom-apq8084-ifc6540.dtb \
qcom-apq8084-mtp.dtb \
@@ -30,6 +30,7 @@ Signed-off-by: John Crispin <john at phrozen.org>
qcom-ipq4019-ap.dk07.1-c1.dtb \
qcom-ipq4019-ap.dk07.1-c2.dtb \
+ qcom-ipq4019-a62.dtb \
++ qcom-ipq4019-fritzbox-7530.dtb \
+ qcom-ipq4019-map-ac2200.dtb \
+ qcom-ipq4028-wpj428.dtb \
+ qcom-ipq4029-gl-b1300.dtb \
--
2.20.1
_______________________________________________
openwrt-devel mailing list
openwrt-devel at lists.openwrt.org
https://lists.openwrt.org/mailman/listinfo/openwrt-devel
More information about the openwrt-devel
mailing list