[OpenWrt-Devel] [PATCH v2 3/4] ath79: add support for Netgear WNDR4300 v2
Michal Cieslakiewicz
michal.cieslakiewicz at wp.pl
Sun Dec 22 15:54:33 EST 2019
This patch introduces support for Netgear WNDR4300v2.
Specification
=============
* Description: Netgear WNDR4300 v2
* Loader: U-boot
* SOC: Qualcomm Atheros QCA9563 (775 MHz)
* RAM: 128 MiB
* Flash: 2 MiB SPI-NOR + 128 MiB SPI-NAND
- NOR: U-boot binary: 256 KiB
- NOR: U-boot environment: 64 KiB
- NOR: ART Backup: 64 KiB
- NOR: Config: 64 KiB
- NOR: Traffic Meter: 64 KiB
- NOR: POT: 64 KiB
- NOR: Reserved: 1408 KiB
- NOR: ART: 64 KiB
- NAND: Firmware: 25600 KiB (see notes for OpenWrt)
- NAND: Language: 2048 KiB
- NAND: mtdoops Crash Dump: 128 KiB
- NAND: Reserved: 103296 KiB
* Ethernet: 5 x 10/100/1000 (4 x LAN, 1 x WAN) (AR8337)
* Wireless:
- 2.4 GHz b/g/n (internal)
- 5 GHz a/n (AR9580)
* USB: yes, 1 x USB 2.0
* Buttons:
- Reset
- WiFi (rfkill)
- WPS
* LEDs:
- Power (amber/green)
- WAN (amber/green)
- WLAN 2G (green)
- WLAN 5G (blue)
- 4 x LAN (amber/green)
- USB (green)
- WPS (green)
* UART: 4-pin connector JP1, 3.3V (Vcc, TX, RX, GND), 115200 8N1
* Power supply: DC 12V 1.5A
* MAC addresses: LAN=WLAN2G on case label, WAN +1, WLAN5G +2
Important Notes
===============
0. NOR Flash (2 MiB) is not touched by OpenWrt installation.
1. NAND Flash (128 MiB) layout under OpenWrt is changed as follows:
all space is split between 4 MiB kernel and 124 MiB UBI areas;
vendor partitions (language and mtdoops) are removed; kernel space
size can be further expanded if needed; maximum image size is set
to 25600k for compatibility reasons and can also be increased.
2. CPU clock is 775 MHz, not 750 MHz.
3. 5 GHz wireless radio chip is Atheros AR9580-AR1A with bogus PCI
device ID 0xabcd. For ath9k driver to load successfully, this is
overriden in DTS with correct value for this chip, 0x0033.
4. RFKILL button is wired to AR9580 pin 9 which is normally disabled
by chip definition in ath9k code (0x0000F4FF gpio mask). Therefore
'qca,gpio-mask=<0xf6ff>' hack must be used for button to work
properly.
5. USB port is always on, no GPIO for 5V power control has been
identified.
Installation
============
* TFTP recovery
* TFTP via U-boot prompt
* sysupgrade
* Web interface
Test build configuration
========================
CONFIG_TARGET_ath79=y
CONFIG_TARGET_ath79_nand=y
CONFIG_TARGET_ath79_nand_DEVICE_netgear_wndr4300-v2=y
CONFIG_ALL_KMODS=y
CONFIG_DEVEL=y
CONFIG_CCACHE=y
CONFIG_COLLECT_KERNEL_DEBUG=y
CONFIG_IMAGEOPT=y
Signed-off-by: Michal Cieslakiewicz <michal.cieslakiewicz at wp.pl>
---
package/boot/uboot-envtools/files/ath79 | 1 +
.../linux/ath79/dts/qca9563_netgear_wndr.dtsi | 256 ++++++++++++++++++
.../ath79/dts/qca9563_netgear_wndr4300-v2.dts | 19 ++
target/linux/ath79/image/nand.mk | 11 +
.../ath79/nand/base-files/etc/board.d/01_leds | 3 +-
.../nand/base-files/etc/board.d/02_network | 6 +-
.../etc/hotplug.d/firmware/10-ath9k-eeprom | 6 +-
7 files changed, 297 insertions(+), 5 deletions(-)
create mode 100644 target/linux/ath79/dts/qca9563_netgear_wndr.dtsi
create mode 100644 target/linux/ath79/dts/qca9563_netgear_wndr4300-v2.dts
diff --git a/package/boot/uboot-envtools/files/ath79 b/package/boot/uboot-envtools/files/ath79
index f956cf4ed4..85a0342a60 100644
--- a/package/boot/uboot-envtools/files/ath79
+++ b/package/boot/uboot-envtools/files/ath79
@@ -26,6 +26,7 @@ glinet,gl-ar750s-nor-nand|\
librerouter,librerouter-v1|\
netgear,ex6400|\
netgear,ex7300|\
+netgear,wndr4300-v2|\
netgear,wnr1000-v2|\
netgear,wnr2000-v3|\
netgear,wnr2200-8m|\
diff --git a/target/linux/ath79/dts/qca9563_netgear_wndr.dtsi b/target/linux/ath79/dts/qca9563_netgear_wndr.dtsi
new file mode 100644
index 0000000000..2ab9b0b34a
--- /dev/null
+++ b/target/linux/ath79/dts/qca9563_netgear_wndr.dtsi
@@ -0,0 +1,256 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+
+#include "qca956x.dtsi"
+
+/ {
+ chosen {
+ bootargs = "console=ttyS0,115200n8";
+ };
+
+ aliases {
+ led-boot = &led_power_amber;
+ led-failsafe = &led_power_amber;
+ led-running = &led_power_green;
+ led-upgrade = &led_power_amber;
+ label-mac-device = ð0;
+ };
+
+ keys {
+ compatible = "gpio-keys";
+
+ wps {
+ label = "wps";
+ linux,code = <KEY_WPS_BUTTON>;
+ gpios = <&gpio 1 GPIO_ACTIVE_LOW>;
+ };
+
+ reset {
+ label = "reset";
+ linux,code = <KEY_RESTART>;
+ gpios = <&gpio 2 GPIO_ACTIVE_LOW>;
+ };
+ };
+
+ ath9k-keys {
+ compatible = "gpio-keys-polled";
+ poll-interval = <20>;
+
+ rfkill {
+ label = "rfkill";
+ linux,code = <KEY_RFKILL>;
+ gpios = <&ath9k 9 GPIO_ACTIVE_LOW>;
+ debounce-interval = <60>;
+ };
+ };
+
+ leds: leds {
+ compatible = "gpio-leds";
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&jtag_disable_pins>;
+
+ led_power_green: power_green {
+ label = "netgear:green:power";
+ gpios = <&gpio 5 GPIO_ACTIVE_LOW>;
+ };
+
+ led_power_amber: power_amber {
+ label = "netgear:amber:power";
+ gpios = <&gpio 6 GPIO_ACTIVE_LOW>;
+ default-state = "keep";
+ };
+
+ wan_green {
+ label = "netgear:green:wan";
+ gpios = <&gpio 17 GPIO_ACTIVE_LOW>;
+ };
+
+ wan_amber {
+ label = "netgear:amber:wan";
+ gpios = <&gpio 16 GPIO_ACTIVE_LOW>;
+ };
+
+ wlan2g_green {
+ label = "netgear:green:wlan2g";
+ gpios = <&gpio 19 GPIO_ACTIVE_LOW>;
+ linux,default-trigger = "phy0tpt";
+ };
+
+ wps_green {
+ label = "netgear:green:wps";
+ gpios = <&gpio 15 GPIO_ACTIVE_LOW>;
+ };
+ };
+
+ ath9k-leds {
+ compatible = "gpio-leds";
+
+ wlan5g_blue {
+ label = "netgear:blue:wlan5g";
+ gpios = <&ath9k 7 GPIO_ACTIVE_LOW>;
+ linux,default-trigger = "phy1tpt";
+ };
+ };
+};
+
+&spi {
+ status = "okay";
+
+ num-cs = <2>;
+ cs-gpios = <0>, <0>;
+
+ flash at 0 {
+ compatible = "jedec,spi-nor";
+ reg = <0>;
+ spi-max-frequency = <25000000>;
+
+ partitions {
+ compatible = "fixed-partitions";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ partition at 0 {
+ label = "u-boot";
+ reg = <0x0 0x40000>;
+ read-only;
+ };
+
+ partition at 40000 {
+ label = "u-boot-env";
+ reg = <0x40000 0x10000>;
+ };
+
+ partition at 50000 {
+ label = "caldata_backup";
+ reg = <0x50000 0x10000>;
+ read-only;
+ };
+
+ partition at 60000 {
+ label = "config";
+ reg = <0x60000 0x10000>;
+ };
+
+ partition at 70000 {
+ label = "traffic_meter";
+ reg = <0x70000 0x10000>;
+ };
+
+ partition at 80000 {
+ label = "pot";
+ reg = <0x80000 0x10000>;
+ };
+
+ partition at 90000 {
+ label = "reserved";
+ reg = <0x90000 0x160000>;
+ };
+
+ art: partition at 1f0000 {
+ label = "caldata";
+ reg = <0x1f0000 0x10000>;
+ read-only;
+ };
+ };
+ };
+
+ flash at 1 {
+ compatible = "spi-nand";
+ reg = <1>;
+ spi-max-frequency = <25000000>;
+
+ partitions {
+ compatible = "fixed-partitions";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ partition at 0 {
+ label = "kernel";
+ reg = <0x0 0x400000>;
+ };
+
+ partition at 400000 {
+ label = "ubi";
+ reg = <0x400000 0x7c00000>;
+ };
+ };
+ };
+};
+
+&mdio0 {
+ status = "okay";
+
+ phy-mask = <0>;
+
+ phy0: ethernet-phy at 0 {
+ reg = <0>;
+ phy-mode = "sgmii";
+ qca,mib-poll-interval = <500>;
+
+ qca,ar8327-initvals = <
+ 0x04 0x00000080 /* PORT0 PAD MODE CTRL */
+ 0x10 0x81000080 /* POWER_ON_STRIP */
+ 0x50 0xcc35cc35 /* LED_CTRL0 */
+ 0x54 0xcb37cb37 /* LED_CTRL1 */
+ 0x58 0x00000000 /* LED_CTRL2 */
+ 0x5c 0x00f3cf00 /* LED_CTRL3 */
+ 0x7c 0x0000007e /* PORT0_STATUS */
+ 0x94 0x00000200 /* PORT6_STATUS */
+ >;
+ };
+};
+
+ð0 {
+ status = "okay";
+
+ pll-data = <0x03000101 0x00000101 0x00001919>;
+
+ mtd-mac-address = <&art 0x0>;
+
+ phy-mode = "sgmii";
+ phy-handle = <&phy0>;
+};
+
+&wmac {
+ status = "okay";
+
+ mtd-mac-address = <&art 0x0>;
+ qca,no-eeprom;
+};
+
+&pcie {
+ status = "okay";
+
+ ath9k: wifi at 0,0 {
+ /* chip is AR9580, override bogus PCI ID 168c:abcd */
+ compatible = "pci168c,0033";
+ reg = <0x0000 0 0 0 0>;
+ mtd-mac-address = <&art 0xc>;
+ qca,no-eeprom;
+ qca,gpio-mask=<0xf6ff>; /* unmask pin 9 for RFKILL button */
+ #gpio-cells = <2>;
+ gpio-controller;
+ };
+};
+
+&usb_phy0 {
+ status = "okay";
+};
+
+&usb0 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "okay";
+
+ hub_port0: port at 1 {
+ reg = <1>;
+ #trigger-source-cells = <0>;
+ };
+};
+
+&uart {
+ status = "okay";
+};
diff --git a/target/linux/ath79/dts/qca9563_netgear_wndr4300-v2.dts b/target/linux/ath79/dts/qca9563_netgear_wndr4300-v2.dts
new file mode 100644
index 0000000000..e4b4ba2ac6
--- /dev/null
+++ b/target/linux/ath79/dts/qca9563_netgear_wndr4300-v2.dts
@@ -0,0 +1,19 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+
+/dts-v1/;
+
+#include "qca9563_netgear_wndr.dtsi"
+
+/ {
+ compatible = "netgear,wndr4300-v2", "qca,qca9563";
+ model = "Netgear WNDR4300 v2";
+};
+
+&leds {
+ usb_green {
+ label = "netgear:green:usb";
+ gpios = <&gpio 7 GPIO_ACTIVE_LOW>;
+ trigger-sources = <&hub_port0>;
+ linux,default-trigger = "usbport";
+ };
+};
diff --git a/target/linux/ath79/image/nand.mk b/target/linux/ath79/image/nand.mk
index 5f893e0044..2094bd1d19 100644
--- a/target/linux/ath79/image/nand.mk
+++ b/target/linux/ath79/image/nand.mk
@@ -151,6 +151,17 @@ define Device/netgear_wndr4300
endef
TARGET_DEVICES += netgear_wndr4300
+define Device/netgear_wndr4300-v2
+ SOC := qca9563
+ DEVICE_MODEL := WNDR4300
+ DEVICE_VARIANT := v2
+ NETGEAR_KERNEL_MAGIC := 0x27051956
+ NETGEAR_BOARD_ID := WNDR4500series
+ NETGEAR_HW_ID := 29764821+2+128+128+3x3+3x3+5508012175
+ $(Device/netgear_ath79_nand)
+endef
+TARGET_DEVICES += netgear_wndr4300-v2
+
define Device/zyxel_nbg6716
SOC := qca9558
DEVICE_VENDOR := ZyXEL
diff --git a/target/linux/ath79/nand/base-files/etc/board.d/01_leds b/target/linux/ath79/nand/base-files/etc/board.d/01_leds
index 49d4005495..0376b7cfc6 100755
--- a/target/linux/ath79/nand/base-files/etc/board.d/01_leds
+++ b/target/linux/ath79/nand/base-files/etc/board.d/01_leds
@@ -13,7 +13,8 @@ glinet,gl-ar300m-nor)
ucidef_set_led_netdev "lan" "LAN" "gl-ar300m:green:lan" "eth0"
;;
netgear,wndr3700-v4|\
-netgear,wndr4300)
+netgear,wndr4300|\
+netgear,wndr4300-v2)
ucidef_set_led_switch "wan-amber" "WAN (amber)" "netgear:amber:wan" "switch0" "0x20"
;;
esac
diff --git a/target/linux/ath79/nand/base-files/etc/board.d/02_network b/target/linux/ath79/nand/base-files/etc/board.d/02_network
index f7e43addc1..135a06d44b 100755
--- a/target/linux/ath79/nand/base-files/etc/board.d/02_network
+++ b/target/linux/ath79/nand/base-files/etc/board.d/02_network
@@ -17,7 +17,8 @@ ath79_setup_interfaces()
"0 at eth0" "2:lan:2" "3:lan:1" "1:wan"
;;
netgear,wndr3700-v4|\
- netgear,wndr4300)
+ netgear,wndr4300|\
+ netgear,wndr4300-v2)
ucidef_add_switch "switch0" \
"0 at eth0" "1:lan:4" "2:lan:3" "3:lan:2" "4:lan:1" "5:wan"
;;
@@ -37,7 +38,8 @@ ath79_setup_macs()
case "$board" in
netgear,wndr3700-v4|\
- netgear,wndr4300)
+ netgear,wndr4300|\
+ netgear,wndr4300-v2)
wan_mac=$(mtd_get_mac_binary caldata 0x6)
;;
zyxel,nbg6716)
diff --git a/target/linux/ath79/nand/base-files/etc/hotplug.d/firmware/10-ath9k-eeprom b/target/linux/ath79/nand/base-files/etc/hotplug.d/firmware/10-ath9k-eeprom
index 25bafe67ac..7ee291d109 100644
--- a/target/linux/ath79/nand/base-files/etc/hotplug.d/firmware/10-ath9k-eeprom
+++ b/target/linux/ath79/nand/base-files/etc/hotplug.d/firmware/10-ath9k-eeprom
@@ -10,7 +10,8 @@ case "$FIRMWARE" in
"ath9k-eeprom-ahb-18100000.wmac.bin")
case $board in
netgear,wndr3700-v4|\
- netgear,wndr4300)
+ netgear,wndr4300|\
+ netgear,wndr4300-v2)
caldata_extract "caldata" 0x1000 0x440
;;
zyxel,nbg6716)
@@ -25,7 +26,8 @@ case "$FIRMWARE" in
"ath9k-eeprom-pci-0000:00:00.0.bin")
case $board in
netgear,wndr3700-v4|\
- netgear,wndr4300)
+ netgear,wndr4300|\
+ netgear,wndr4300-v2)
caldata_extract "caldata" 0x5000 0x440
;;
*)
--
2.24.1
_______________________________________________
openwrt-devel mailing list
openwrt-devel at lists.openwrt.org
https://lists.openwrt.org/mailman/listinfo/openwrt-devel
More information about the openwrt-devel
mailing list