[OpenWrt-Devel] [PATCH v3] ramips: add Asus RT-AC85P
Gábor Varga
vargagab at gmail.com
Fri Aug 23 05:04:36 EDT 2019
Hi!
Although it looks like the Asus RT-AC85P and the Asus RT-AC65P models are
identical, but I have separated them into two dts and have introduced the
HW version into the names (for the new versions in the future).
I have an alternative installation method via SSH:
Note: The user/password for SSH is identical with the one used in the
Web-interface.
1. Complete the initial setup wizard.
2. Activate SSH under "Administration" -> "System".
3. Transfer the OpenWrt factory image via scp:
> scp openwrt-ramips-mt7621-asus_rt-ac65p-r01-squashfs-factory.bin
admin at 192.168.50.1:/tmp
4. Connect via SSH to the router.
> ssh admin at 192.168.50.1
5. Write the OpenWrt image to flash.
> mtd-write -i
/tmp/openwrt-ramips-mt7621-asus_rt-ac65p-r01-squashfs-factory.bin -d linux
6. Reboot the router
> reboot
Another thing: I don't know, if it's good method to replace the second
firmware partition with OpenWrt image during sysupgrade. When we don't do
that, than we have always a factory firmware on the secondary firmware
partition, so the back to the factory firmware would be much easier.
So, the new patch for the separated models:
diff --git a/target/linux/ramips/base-files/etc/board.d/02_network
b/target/linux/ramips/base-files/etc/board.d/02_network
index c0de9d4e50..110e921f38 100755
--- a/target/linux/ramips/base-files/etc/board.d/02_network
+++ b/target/linux/ramips/base-files/etc/board.d/02_network
@@ -300,6 +300,8 @@ ramips_setup_interfaces()
ucidef_add_switch "switch0" \
"0:lan:4" "1:lan:3" "2:lan:2" "3:lan:1" "4:wan:5" "6 at eth0"
;;
+ asus,rt-ac65p-r01|\
+ asus,rt-ac85p-r01|\
dlink,dir-860l-b1|\
elecom,wrc-1167ghbk2-s|\
elecom,wrc-1900gst|\
@@ -537,6 +539,10 @@ ramips_setup_macs()
lan_mac=$(mtd_get_mac_binary factory 0xe000)
wan_mac=$(mtd_get_mac_binary factory 0xe006)
;;
+ asus,rt-ac65p-r01|\
+ asus,rt-ac85p-r01)
+ wan_mac=$(mtd_get_mac_ascii u-boot-env et1macaddr)
+ ;;
asus,rt-n56u)
lan_mac=$(macaddr_setbit_la "$(cat /sys/class/net/eth0/address)")
wan_mac=$(mtd_get_mac_binary factory 0x8004)
diff --git a/target/linux/ramips/base-files/lib/upgrade/platform.sh
b/target/linux/ramips/base-files/lib/upgrade/platform.sh
index a65492a309..7a50c61b1d 100755
--- a/target/linux/ramips/base-files/lib/upgrade/platform.sh
+++ b/target/linux/ramips/base-files/lib/upgrade/platform.sh
@@ -18,9 +18,18 @@ platform_do_upgrade() {
mikrotik,rbm33g)
[ -z "$(rootfs_type)" ] && mtd erase firmware
;;
+ asus,rt-ac65p-r01|\
+ asus,rt-ac85p-r01)
+ echo "Backing up firmware"
+ dd if=/dev/mtd4 bs=1024 count=4096 > /tmp/backup_firmware.bin
+ dd if=/dev/mtd5 bs=1024 count=52224 >> /tmp/backup_firmware.bin
+ mtd -e firmware2 write /tmp/backup_firmware.bin firmware2
+ ;;
esac
case "$board" in
+ asus,rt-ac65p-r01|\
+ asus,rt-ac85p-r01|\
hiwifi,hc5962|\
netgear,r6220|\
netgear,r6350|\
diff --git a/target/linux/ramips/dts/mt7621_asus_rt-ac65p-r01.dts
b/target/linux/ramips/dts/mt7621_asus_rt-ac65p-r01.dts
new file mode 100644
index 0000000000..3d2d1bfe6d
--- /dev/null
+++ b/target/linux/ramips/dts/mt7621_asus_rt-ac65p-r01.dts
@@ -0,0 +1,9 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/dts-v1/;
+
+#include "mt7621_asus_rt-ac85p.dtsi"
+
+/ {
+ compatible = "asus,rt-ac65p-r01", "mediatek,mt7621-soc";
+ model = "Asus RT-AC65P R01";
+};
diff --git a/target/linux/ramips/dts/mt7621_asus_rt-ac85p-r01.dts
b/target/linux/ramips/dts/mt7621_asus_rt-ac85p-r01.dts
new file mode 100644
index 0000000000..115d52c71c
--- /dev/null
+++ b/target/linux/ramips/dts/mt7621_asus_rt-ac85p-r01.dts
@@ -0,0 +1,9 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/dts-v1/;
+
+#include "mt7621_asus_rt-ac85p.dtsi"
+
+/ {
+ compatible = "asus,rt-ac85p-r01", "mediatek,mt7621-soc";
+ model = "Asus RT-AC85P R01";
+};
diff --git a/target/linux/ramips/dts/mt7621_asus_rt-ac85p.dtsi
b/target/linux/ramips/dts/mt7621_asus_rt-ac85p.dtsi
new file mode 100644
index 0000000000..aa1229ab03
--- /dev/null
+++ b/target/linux/ramips/dts/mt7621_asus_rt-ac85p.dtsi
@@ -0,0 +1,161 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/dts-v1/;
+
+#include "mt7621.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+
+/ {
+ aliases {
+ led-boot = &led_power;
+ led-failsafe = &led_power;
+ led-running = &led_power;
+ led-upgrade = &led_power;
+ };
+
+ chosen {
+ bootargs = "console=ttyS0,57600";
+ };
+
+ palmbus: palmbus at 1E000000 {
+ i2c at 900 {
+ status = "okay";
+ };
+ };
+
+ keys {
+ compatible = "gpio-keys";
+
+ reset {
+ label = "reset";
+ gpios = <&gpio0 3 GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_RESTART>;
+ };
+
+ wps {
+ label = "wps";
+ gpios = <&gpio0 6 GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_WPS_BUTTON>;
+ };
+ };
+
+ leds {
+ compatible = "gpio-leds";
+
+ led_power: power {
+ label = "rt-ac85p:blue:power";
+ gpios = <&gpio0 4 GPIO_ACTIVE_LOW>;
+ linux,default-trigger = "phy0tpt";
+ };
+ wlan2g {
+ label = "rt-ac85p:blue:wlan2g";
+ gpios = <&gpio0 10 GPIO_ACTIVE_LOW>;
+ linux,default-trigger = "phy0radio";
+ };
+
+ wlan5g {
+ label = "rt-ac85p:blue:wlan5g";
+ gpios = <&gpio0 8 GPIO_ACTIVE_LOW>;
+ linux,default-trigger = "phy1radio";
+ };
+ };
+};
+
+&sdhci {
+ status = "okay";
+};
+
+&nand {
+ status = "okay";
+
+ partitions {
+ compatible = "fixed-partitions";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ partition at 0 {
+ label = "u-boot";
+ reg = <0x0 0xe0000>;
+ read-only;
+ };
+
+ partition at e0000 {
+ label = "u-boot-env";
+ reg = <0xe0000 0x100000>;
+ read-only;
+ };
+
+ factory: partition at 1e0000 {
+ label = "factory";
+ reg = <0x1e0000 0x100000>;
+ read-only;
+ };
+
+ factory2: partition at 2e0000 {
+ label = "factory2";
+ reg = <0x2e0000 0x100000>;
+ read-only;
+ };
+
+ partition at 3e0000 {
+ label = "kernel";
+ reg = <0x3e0000 0x400000>;
+ };
+
+ partition at 7e0000 {
+ label = "ubi";
+ reg = <0x7e0000 0x2e00000>;
+ };
+
+ partition at 35e0000 {
+ label = "firmware2";
+ reg = <0x35e0000 0x3200000>;
+ };
+ };
+};
+
+&pcie {
+ status = "okay";
+};
+
+&pcie0 {
+ wifi0: wifi at 0,0 {
+ compatible = "pci14c3,7603";
+ reg = <0x0000 0 0 0 0>;
+ mediatek,mtd-eeprom = <&factory 0x0000>;
+ ieee80211-freq-limit = <2400000 2500000>;
+ mtd-mac-address = <&factory 0x4>;
+ };
+};
+
+&pcie1 {
+ wifi1: wifi at 0,0 {
+ compatible = "pci14c3,7662";
+ reg = <0x0000 0 0 0 0>;
+ mediatek,mtd-eeprom = <&factory 0x8000>;
+ ieee80211-freq-limit = <5000000 6000000>;
+ mtd-mac-address = <&factory 0x8004>;
+ };
+};
+
+ðernet {
+ mtd-mac-address = <&factory 0xe000>;
+ mediatek,portmap = "wllll";
+ port at 5 {
+ status = "disabled";
+ };
+};
+
+&i2c {
+ status = "disabled";
+};
+
+&pinctrl {
+ state_default: pinctrl0 {
+ gpio {
+ ralink,group = "uart2", "uart3", "i2c";
+ ralink,function = "gpio";
+ };
+ };
+};
diff --git a/target/linux/ramips/image/mt7621.mk
b/target/linux/ramips/image/mt7621.mk
index d32feb7eab..7efe2cdc7f 100644
--- a/target/linux/ramips/image/mt7621.mk
+++ b/target/linux/ramips/image/mt7621.mk
@@ -115,6 +115,40 @@ define Device/asus_rt-ac57u
endef
TARGET_DEVICES += asus_rt-ac57u
+define Device/asus_rt-ac65p-r01
+ MTK_SOC := mt7621
+ DEVICE_VENDOR := ASUS
+ DEVICE_MODEL := RT-AC65P
+ DEVICE_VARIANT := R01
+ IMAGE_SIZE := 51200k
+ UBINIZE_OPTS := -E 5
+ BLOCKSIZE := 128k
+ PAGESIZE := 2048
+ KERNEL_SIZE := 4096k
+ IMAGES += factory.bin
+ IMAGE/sysupgrade.bin := sysupgrade-tar | append-metadata
+ IMAGE/factory.bin := append-kernel | pad-to $$(KERNEL_SIZE) | append-ubi
| check-size $$$$(IMAGE_SIZE)
+ DEVICE_PACKAGES := kmod-usb3 kmod-mt7615e wpad-basic uboot-envtools
+endef
+TARGET_DEVICES += asus_rt-ac65p-r01
+
+define Device/asus_rt-ac85p-r01
+ MTK_SOC := mt7621
+ DEVICE_VENDOR := ASUS
+ DEVICE_MODEL := RT-AC85P
+ DEVICE_VARIANT := R01
+ IMAGE_SIZE := 51200k
+ UBINIZE_OPTS := -E 5
+ BLOCKSIZE := 128k
+ PAGESIZE := 2048
+ KERNEL_SIZE := 4096k
+ IMAGES += factory.bin
+ IMAGE/sysupgrade.bin := sysupgrade-tar | append-metadata
+ IMAGE/factory.bin := append-kernel | pad-to $$(KERNEL_SIZE) | append-ubi
| check-size $$$$(IMAGE_SIZE)
+ DEVICE_PACKAGES := kmod-usb3 kmod-mt7615e wpad-basic uboot-envtools
+endef
+TARGET_DEVICES += asus_rt-ac85p-r01
+
define Device/buffalo_wsr-1166dhp
MTK_SOC := mt7621
IMAGE/sysupgrade.bin := trx | pad-rootfs | append-metadata
diff --git
a/target/linux/ramips/patches-4.14/0039-mtd-add-mt7621-nand-support.patch
b/target/linux/ramips/patches-4.14/0039-mtd-add-mt7621-nand-support.patch
index d50e689110..d2d69b4ff4 100644
---
a/target/linux/ramips/patches-4.14/0039-mtd-add-mt7621-nand-support.patch
+++
b/target/linux/ramips/patches-4.14/0039-mtd-add-mt7621-nand-support.patch
@@ -4256,7 +4256,7 @@ Signed-off-by: John Crispin <blogic at openwrt.org>
+#endif /* __NAND_DEF_H__ */
--- /dev/null
+++ b/drivers/mtd/nand/nand_device_list.h
-@@ -0,0 +1,59 @@
+@@ -0,0 +1,60 @@
+/* Copyright Statement:
+ *
+ * This software/firmware and related documentation ("MediaTek Software")
are
@@ -4308,6 +4308,7 @@ Signed-off-by: John Crispin <blogic at openwrt.org>
+ {0xC8DC, 0x909554, 5, 8, 512, 128, 2048, 64, 0x30C77fff, "F59L4G81A", 0},
+ {0xECD3, 0x519558, 5, 8, 1024, 128, 2048, 64, 0x44333, "K9K8G8000", 0},
+ {0xC2F1, 0x801DC2, 4, 8, 128, 128, 2048, 64, 0x30C77fff,
"MX30LF1G08AA", 0},
++ {0xC2F1, 0x809502, 4, 8, 128, 128, 2048, 64, 0x30C77fff,
"MX30LF1G18AC", 0},
+ {0x98D3, 0x902676, 5, 8, 1024, 256, 4096, 224, 0x00C25332,
"TC58NVG3S0F", 0},
+ {0x01DA, 0x909546, 5, 8, 256, 128, 2048, 128, 0x30C77fff,
"S34ML02G200TF", 0},
+ {0x01DC, 0x909556, 5, 8, 512, 128, 2048, 128, 0x30C77fff,
"S34ML04G200TF", 0},
Birger Koblitz <mail at birger-koblitz.de> ezt írta (időpont: 2019. aug. 4.,
V, 6:46):
> ramips: add Asus RT-AC85P
>
> SoC: MediaTek MT7621AT dual-core @ 880MHz
> RAM: 256M (Winbond W632GG6KB-1)
> FLASH: 128MB (Macronix MX30LF1G18AC-TI)
> WiFi: - 2.4GHz MediaTek MT7615N bgn
> - 5GHz MediaTek MT7615N nac
> Switch: SoC integrated Gigabit Switch (4 x LAN, 1 x WAN)
> USB: 1 x USB 3.1 (Gen 1)
> BTN: Reset, WPS
> LED: - Power (blue)
> - 5Ghz (blue)
> - 2.4GHz (blue)
> - Internet (blue)
> - 4x LAN (blue)
> (LAN/WAN leds are not controllable by GPIOs)
> UART: UART is present as Pads marked J4 on the PCB.
> 3.3V - TX - RX - GND / 57600-8N1
> 3.3V is the square pad
> MAC: The MAC address on the router-label matches the MAC of
> the 2.4 GHz WiFi.
> LAN and WAN MAC are identical: MAC_LABEL+4
> 5 GHz WiFi MAC: also MAC_LABEL+4
>
>
> Installation
> ------------
> Via U-Boot tftpd:
> Switch on device, within 2s press reset button and keep pressed
> until power LED starts blinking slowly.
> Upload factory image via tftp put, the router's ip is 192.168.1.1
> and expects the client on 192.168.1.75.
>
> The images also work on the Asus RT-AC65P models as tested by Gabor.
>
> Signed-off-by: Birger Koblitz <mail at birger-koblitz.de>
> Tested-by: Gabor Varga <vargagab at gmail.com>
>
> ---
>
> v2: Corrected sorting of entries in 02_network
> Model name corrected in .dts
> Whitespace fixes in .dts
> wifi0/1 labels added to wifi nodes in .dts
> Device name capitalized in mt7621.mk
>
> v3: Added firmware backup to firmware2 partition before sysupgrade
> Corrected modules included in image
>
> diff --git a/target/linux/ramips/base-files/etc/board.d/02_network
> b/target/linux/ramips/base-files/etc/board.d/02_network
> index 2f9a02256e..ab90041d92 100755
> --- a/target/linux/ramips/base-files/etc/board.d/02_network
> +++ b/target/linux/ramips/base-files/etc/board.d/02_network
> @@ -231,6 +231,17 @@ ramips_setup_interfaces()
> ucidef_add_switch "switch0" \
> "0:lan" "1:wan" "6 at eth0"
> ;;
> + asus,rt-ac85p|\
> + dlink,dir-860l-b1|\
> + elecom,wrc-1167ghbk2-s|\
> + elecom,wrc-1900gst|\
> + elecom,wrc-2533gst|\
> + huawei,hg255d|\
> + iodata,wn-ax1167gr|\
> + iodata,wn-gx300gr)
> + ucidef_add_switch "switch0" \
> + "1:lan:4" "2:lan:3" "3:lan:2" "4:lan:1" "0:wan" "6 at eth0"
> + ;;
> asus,rt-n15|\
> belkin,f9k1109v1|\
> sitecom,wl-351)
> @@ -298,16 +309,6 @@ ramips_setup_interfaces()
> ucidef_add_switch "switch0" \
> "0:lan:4" "1:lan:3" "2:lan:2" "3:lan:1" "4:wan:5" "6 at eth0"
> ;;
> - dlink,dir-860l-b1|\
> - elecom,wrc-1167ghbk2-s|\
> - elecom,wrc-1900gst|\
> - elecom,wrc-2533gst|\
> - huawei,hg255d|\
> - iodata,wn-ax1167gr|\
> - iodata,wn-gx300gr)
> - ucidef_add_switch "switch0" \
> - "1:lan:4" "2:lan:3" "3:lan:2" "4:lan:1" "0:wan" "6 at eth0"
> - ;;
> dlink,dwr-118-a1)
> ucidef_add_switch "switch0" \
> "1:lan:2" "2:lan:3" "3:lan:1" "4:lan:0" "5:wan" "6 at eth0"
> @@ -531,6 +532,9 @@ ramips_setup_macs()
> lan_mac=$(mtd_get_mac_binary factory 57344)
> wan_mac=$(mtd_get_mac_binary factory 57350)
> ;;
> + asus,rt-ac85p)
> + wan_mac=$(mtd_get_mac_ascii u-boot-env et1macaddr)
> + ;;
> asus,rt-n56u)
> lan_mac=$(macaddr_setbit_la "$(cat /sys/class/net/eth0/address)")
> wan_mac=$(mtd_get_mac_binary factory 32772)
> diff --git a/target/linux/ramips/base-files/lib/upgrade/platform.sh
> b/target/linux/ramips/base-files/lib/upgrade/platform.sh
> index a65492a309..cd9d8ae650 100755
> --- a/target/linux/ramips/base-files/lib/upgrade/platform.sh
> +++ b/target/linux/ramips/base-files/lib/upgrade/platform.sh
> @@ -18,9 +18,16 @@ platform_do_upgrade() {
> mikrotik,rbm33g)
> [ -z "$(rootfs_type)" ] && mtd erase firmware
> ;;
> + asus,rt-ac85p)
> + echo "Backing up firmware"
> + dd if=/dev/mtd4 bs=1024 count=4096 > /tmp/backup_firmware.bin
> + dd if=/dev/mtd5 bs=1024 count=52224 >> /tmp/backup_firmware.bin
> + mtd -e firmware2 write /tmp/backup_firmware.bin firmware2
> + ;;
> esac
>
> case "$board" in
> + asus,rt-ac85p|\
> hiwifi,hc5962|\
> netgear,r6220|\
> netgear,r6350|\
> diff --git a/target/linux/ramips/dts/mt7621_asus_rt-ac85p.dts
> b/target/linux/ramips/dts/mt7621_asus_rt-ac85p.dts
> new file mode 100644
> index 0000000000..7aea207fad
> --- /dev/null
> +++ b/target/linux/ramips/dts/mt7621_asus_rt-ac85p.dts
> @@ -0,0 +1,164 @@
> +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
> +/dts-v1/;
> +
> +#include "mt7621.dtsi"
> +
> +#include <dt-bindings/gpio/gpio.h>
> +#include <dt-bindings/input/input.h>
> +
> +/ {
> + compatible = "asus,rt-ac85p", "mediatek,mt7621-soc";
> + model = "Asus RT-AC85P";
> +
> + aliases {
> + led-boot = &led_power;
> + led-failsafe = &led_power;
> + led-running = &led_power;
> + led-upgrade = &led_power;
> + };
> +
> + chosen {
> + bootargs = "console=ttyS0,57600";
> + };
> +
> + palmbus: palmbus at 1E000000 {
> + i2c at 900 {
> + status = "okay";
> + };
> + };
> +
> + keys {
> + compatible = "gpio-keys";
> +
> + reset {
> + label = "reset";
> + gpios = <&gpio0 3 GPIO_ACTIVE_LOW>;
> + linux,code = <KEY_RESTART>;
> + };
> +
> + wps {
> + label = "wps";
> + gpios = <&gpio0 6 GPIO_ACTIVE_LOW>;
> + linux,code = <KEY_WPS_BUTTON>;
> + };
> + };
> +
> + leds {
> + compatible = "gpio-leds";
> +
> + led_power: power {
> + label = "rt-ac85p:blue:power";
> + gpios = <&gpio0 4 GPIO_ACTIVE_LOW>;
> + linux,default-trigger = "phy0tpt";
> + };
> + wlan2g {
> + label = "rt-ac85p:blue:wlan2g";
> + gpios = <&gpio0 10 GPIO_ACTIVE_LOW>;
> + linux,default-trigger = "phy0radio";
> + };
> +
> + wlan5g {
> + label = "rt-ac85p:blue:wlan5g";
> + gpios = <&gpio0 8 GPIO_ACTIVE_LOW>;
> + linux,default-trigger = "phy1radio";
> + };
> + };
> +};
> +
> +&sdhci {
> + status = "okay";
> +};
> +
> +&nand {
> + status = "okay";
> +
> + partitions {
> + compatible = "fixed-partitions";
> + #address-cells = <1>;
> + #size-cells = <1>;
> +
> + partition at 0 {
> + label = "u-boot";
> + reg = <0x0 0xe0000>;
> + read-only;
> + };
> +
> + partition at e0000 {
> + label = "u-boot-env";
> + reg = <0xe0000 0x100000>;
> + read-only;
> + };
> +
> + factory: partition at 1e0000 {
> + label = "factory";
> + reg = <0x1e0000 0x100000>;
> + read-only;
> + };
> +
> + factory2: partition at 2e0000 {
> + label = "factory2";
> + reg = <0x2e0000 0x100000>;
> + read-only;
> + };
> +
> + partition at 3e0000 {
> + label = "kernel";
> + reg = <0x3e0000 0x400000>;
> + };
> +
> + partition at 7e0000 {
> + label = "ubi";
> + reg = <0x7e0000 0x2e00000>;
> + };
> +
> + partition at 35e0000 {
> + label = "firmware2";
> + reg = <0x35e0000 0x3200000>;
> + };
> + };
> +};
> +
> +&pcie {
> + status = "okay";
> +};
> +
> +&pcie0 {
> + wifi0: wifi at 0,0 {
> + compatible = "pci14c3,7603";
> + reg = <0x0000 0 0 0 0>;
> + mediatek,mtd-eeprom = <&factory 0x0000>;
> + ieee80211-freq-limit = <2400000 2500000>;
> + mtd-mac-address = <&factory 0x4>;
> + };
> +};
> +
> +&pcie1 {
> + wifi1: wifi at 0,0 {
> + compatible = "pci14c3,7662";
> + reg = <0x0000 0 0 0 0>;
> + mediatek,mtd-eeprom = <&factory 0x8000>;
> + ieee80211-freq-limit = <5000000 6000000>;
> + mtd-mac-address = <&factory 0x8004>;
> + };
> +};
> +
> +ðernet {
> + mtd-mac-address = <&factory 0xe000>;
> + mediatek,portmap = "wllll";
> + port at 5 {
> + status = "disabled";
> + };
> +};
> +
> +&i2c {
> + status = "disabled";
> +};
> +
> +&pinctrl {
> + state_default: pinctrl0 {
> + gpio {
> + ralink,group = "uart2", "uart3", "i2c";
> + ralink,function = "gpio";
> + };
> + };
> +};
> diff --git a/target/linux/ramips/image/mt7621.mk
> b/target/linux/ramips/image/mt7621.mk
> index d86eb8cc34..c036a1c308 100644
> --- a/target/linux/ramips/image/mt7621.mk
> +++ b/target/linux/ramips/image/mt7621.mk
> @@ -115,6 +115,22 @@ define Device/asus_rt-ac57u
> endef
> TARGET_DEVICES += asus_rt-ac57u
>
> +define Device/asus_rt-ac85p
> + MTK_SOC := mt7621
> + DEVICE_VENDOR := ASUS
> + DEVICE_MODEL := RT-AC85P
> + IMAGE_SIZE := 51200k
> + UBINIZE_OPTS := -E 5
> + BLOCKSIZE := 128k
> + PAGESIZE := 2048
> + KERNEL_SIZE := 4096k
> + IMAGES += factory.bin
> + IMAGE/sysupgrade.bin := sysupgrade-tar | append-metadata
> + IMAGE/factory.bin := append-kernel | pad-to $$(KERNEL_SIZE) |
> append-ubi | check-size $$$$(IMAGE_SIZE)
> + DEVICE_PACKAGES := kmod-usb3 kmod-mt7615e wpad-basic uboot-envtools
> +endef
> +TARGET_DEVICES += asus_rt-ac85p
> +
> define Device/buffalo_wsr-1166dhp
> MTK_SOC := mt7621
> IMAGE/sysupgrade.bin := trx | pad-rootfs | append-metadata
> diff --git
> a/target/linux/ramips/patches-4.14/0039-mtd-add-mt7621-nand-support.patch
> b/target/linux/ramips/patches-4.14/0039-mtd-add-mt7621-nand-support.patch
> index d50e689110..d2d69b4ff4 100644
> ---
> a/target/linux/ramips/patches-4.14/0039-mtd-add-mt7621-nand-support.patch
> +++
> b/target/linux/ramips/patches-4.14/0039-mtd-add-mt7621-nand-support.patch
> @@ -4256,7 +4256,7 @@ Signed-off-by: John Crispin <blogic at openwrt.org>
> +#endif /* __NAND_DEF_H__ */
> --- /dev/null
> +++ b/drivers/mtd/nand/nand_device_list.h
> -@@ -0,0 +1,59 @@
> +@@ -0,0 +1,60 @@
> +/* Copyright Statement:
> + *
> + * This software/firmware and related documentation ("MediaTek
> Software") are
> @@ -4308,6 +4308,7 @@ Signed-off-by: John Crispin <blogic at openwrt.org>
> + {0xC8DC, 0x909554, 5, 8, 512, 128, 2048, 64, 0x30C77fff,
> "F59L4G81A", 0},
> + {0xECD3, 0x519558, 5, 8, 1024, 128, 2048, 64, 0x44333,
> "K9K8G8000", 0},
> + {0xC2F1, 0x801DC2, 4, 8, 128, 128, 2048, 64, 0x30C77fff,
> "MX30LF1G08AA", 0},
> ++ {0xC2F1, 0x809502, 4, 8, 128, 128, 2048, 64, 0x30C77fff,
> "MX30LF1G18AC", 0},
> + {0x98D3, 0x902676, 5, 8, 1024, 256, 4096, 224, 0x00C25332,
> "TC58NVG3S0F", 0},
> + {0x01DA, 0x909546, 5, 8, 256, 128, 2048, 128, 0x30C77fff,
> "S34ML02G200TF", 0},
> + {0x01DC, 0x909556, 5, 8, 512, 128, 2048, 128, 0x30C77fff,
> "S34ML04G200TF", 0},
>
>
> _______________________________________________
> openwrt-devel mailing list
> openwrt-devel at lists.openwrt.org
> https://lists.openwrt.org/mailman/listinfo/openwrt-devel
>
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://lists.infradead.org/pipermail/openwrt-devel/attachments/20190823/48acaada/attachment.htm>
-------------- next part --------------
_______________________________________________
openwrt-devel mailing list
openwrt-devel at lists.openwrt.org
https://lists.openwrt.org/mailman/listinfo/openwrt-devel
More information about the openwrt-devel
mailing list