[OpenWrt-Devel] [PATCH v3 5/5] ath79: add support for Netgear WNR2200
Michal Cieslakiewicz
michal.cieslakiewicz at wp.pl
Sun Aug 11 16:48:28 EDT 2019
This patch adds ath79 support for Netgear WNR2200.
Router was previously supported by ar71xx target only.
Specification
=============
* Description: Netgear WNR2200
* Loader: U-boot
* SOC: Atheros AR7241 (360 MHz)
* RAM: 64 MiB
* Flash: 8 MiB (SPI NOR)
- U-boot binary: 256 KiB
- U-boot environment: 64 KiB
- Firmware: 7808 KiB
- ART: 64 KiB
* Ethernet: 4 x 10/100 LAN + 1 x 10/100 WAN
* Wireless: 2.4 GHz b/g/n (Atheros AR9287)
* USB: yes, 1 x USB 2.0
* Buttons:
- Reset
- WiFi (rfkill)
- WPS
* LEDs:
- Power (amber/green)
- WAN (amber/green)
- WLAN (blue)
- 4 x LAN (amber/green)
- WPS (green)
* UART: 4-pin connector JP1, 3.3V (Vcc, TX, RX, GND), 115200 8N1
* Power supply: DC 12V 1.5A
* MAC addresses: LAN on case label, WAN +1, WLAN +2
Installation
============
* TFTP recovery
* TFTP via U-boot prompt
* sysupgrade
* Web interface
Test build configuration
========================
CONFIG_TARGET_ath79=y
CONFIG_TARGET_ath79_generic=y
CONFIG_TARGET_ath79_generic_DEVICE_netgear_wnr2200=y
CONFIG_ALL_KMODS=y
CONFIG_DEVEL=y
CONFIG_CCACHE=y
CONFIG_COLLECT_KERNEL_DEBUG=y
CONFIG_IMAGEOPT=y
CONFIG_KERNEL_DEBUG_INFO=y
CONFIG_KERNEL_DEBUG_KERNEL=y
Signed-off-by: Michal Cieslakiewicz <michal.cieslakiewicz at wp.pl>
---
.../ath79/base-files/etc/board.d/01_leds | 3 +-
.../ath79/base-files/etc/board.d/02_network | 1 +
.../etc/hotplug.d/firmware/10-ath9k-eeprom | 1 +
.../ath79/dts/ar7241_netgear_wnr2200.dts | 237 ++++++++++++++++++
target/linux/ath79/image/generic.mk | 14 ++
5 files changed, 255 insertions(+), 1 deletion(-)
create mode 100644 target/linux/ath79/dts/ar7241_netgear_wnr2200.dts
diff --git a/target/linux/ath79/base-files/etc/board.d/01_leds b/target/linux/ath79/base-files/etc/board.d/01_leds
index 7eca103a9e..82006efb6b 100755
--- a/target/linux/ath79/base-files/etc/board.d/01_leds
+++ b/target/linux/ath79/base-files/etc/board.d/01_leds
@@ -104,7 +104,8 @@ glinet,gl-x750)
ucidef_set_led_netdev "wan" "WAN" "$boardname:green:wan" "eth1"
;;
netgear,wnr1000-v2|\
-netgear,wnr2000-v3)
+netgear,wnr2000-v3|\
+netgear,wnr2200)
ucidef_set_led_netdev "wan-amber" "WAN (amber)" "netgear:amber:wan" "eth0"
ucidef_set_led_default "wan-green" "WAN (green)" "netgear:green:wan" "0"
ucidef_set_led_switch "lan1green" "LAN1 (green)" "netgear:green:lan1" "switch0" "0x02" "0x04"
diff --git a/target/linux/ath79/base-files/etc/board.d/02_network b/target/linux/ath79/base-files/etc/board.d/02_network
index fe491d1c26..7d53f0a2fb 100755
--- a/target/linux/ath79/base-files/etc/board.d/02_network
+++ b/target/linux/ath79/base-files/etc/board.d/02_network
@@ -197,6 +197,7 @@ ath79_setup_interfaces()
;;
netgear,wnr1000-v2|\
netgear,wnr2000-v3|\
+ netgear,wnr2200|\
netgear,wnr612-v2|\
on,n150r|\
tplink,tl-wr740n-v1|\
diff --git a/target/linux/ath79/base-files/etc/hotplug.d/firmware/10-ath9k-eeprom b/target/linux/ath79/base-files/etc/hotplug.d/firmware/10-ath9k-eeprom
index dbe53b6f64..044e6c0afd 100644
--- a/target/linux/ath79/base-files/etc/hotplug.d/firmware/10-ath9k-eeprom
+++ b/target/linux/ath79/base-files/etc/hotplug.d/firmware/10-ath9k-eeprom
@@ -167,6 +167,7 @@ case "$FIRMWARE" in
;;
netgear,wnr1000-v2|\
netgear,wnr2000-v3|\
+ netgear,wnr2200|\
netgear,wnr612-v2|\
on,n150r|\
pcs,cap324|\
diff --git a/target/linux/ath79/dts/ar7241_netgear_wnr2200.dts b/target/linux/ath79/dts/ar7241_netgear_wnr2200.dts
new file mode 100644
index 0000000000..9c439be6f8
--- /dev/null
+++ b/target/linux/ath79/dts/ar7241_netgear_wnr2200.dts
@@ -0,0 +1,237 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/dts-v1/;
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+
+#include "ar7241.dtsi"
+
+/ {
+ compatible = "netgear,wnr2200", "qca,ar7241";
+ model = "Netgear WNR2200";
+
+ chosen {
+ bootargs = "console=ttyS0,115200n8";
+ };
+
+ aliases {
+ led-boot = &power_amber;
+ led-failsafe = &power_amber;
+ led-running = &power_green;
+ led-upgrade = &power_amber;
+ };
+
+ keys {
+ compatible = "gpio-keys-polled";
+ poll-interval = <20>;
+
+ wps {
+ label = "wps";
+ linux,code = <KEY_WPS_BUTTON>;
+ gpios = <&ath9k 5 GPIO_ACTIVE_LOW>;
+ debounce-interval = <60>;
+ };
+
+ reset {
+ label = "reset";
+ linux,code = <KEY_RESTART>;
+ gpios = <&ath9k 6 GPIO_ACTIVE_LOW>;
+ debounce-interval = <60>;
+ };
+
+ rfkill {
+ label = "rfkill";
+ linux,code = <KEY_RFKILL>;
+ gpios = <&ath9k 3 GPIO_ACTIVE_LOW>;
+ debounce-interval = <60>;
+ };
+ };
+
+ leds {
+ compatible = "gpio-leds";
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&jtag_disable_pins &switch_led_disable_pins &clks_disable_pins>;
+
+ wan_green {
+ label = "netgear:green:wan";
+ gpios = <&gpio 17 GPIO_ACTIVE_LOW>;
+ };
+
+ wan_amber {
+ label = "netgear:amber:wan";
+ gpios = <&gpio 12 GPIO_ACTIVE_LOW>;
+ };
+
+ lan1_green {
+ label = "netgear:green:lan1";
+ gpios = <&gpio 13 GPIO_ACTIVE_LOW>;
+ };
+
+ lan1_amber {
+ label = "netgear:amber:lan1";
+ gpios = <&gpio 6 GPIO_ACTIVE_LOW>;
+ };
+
+ lan2_green {
+ label = "netgear:green:lan2";
+ gpios = <&gpio 14 GPIO_ACTIVE_LOW>;
+ };
+
+ lan2_amber {
+ label = "netgear:amber:lan2";
+ gpios = <&gpio 0 GPIO_ACTIVE_LOW>;
+ };
+
+ lan3_green {
+ label = "netgear:green:lan3";
+ gpios = <&gpio 15 GPIO_ACTIVE_LOW>;
+ };
+
+ lan3_amber {
+ label = "netgear:amber:lan3";
+ gpios = <&gpio 11 GPIO_ACTIVE_LOW>;
+ };
+
+ lan4_green {
+ label = "netgear:green:lan4";
+ gpios = <&gpio 16 GPIO_ACTIVE_LOW>;
+ };
+
+ lan4_amber {
+ label = "netgear:amber:lan4";
+ gpios = <&gpio 1 GPIO_ACTIVE_LOW>;
+ };
+
+ wps_green {
+ label = "netgear:green:wps";
+ gpios = <&gpio 7 GPIO_ACTIVE_LOW>;
+ };
+
+ usb_green {
+ label = "netgear:green:usb";
+ gpios = <&gpio 8 GPIO_ACTIVE_LOW>;
+ trigger-sources = <&hub_port>;
+ linux,default-trigger = "usbport";
+ };
+ };
+
+ ath9k-leds {
+ compatible = "gpio-leds";
+
+ power_green: power_green {
+ label = "netgear:green:power";
+ gpios = <&ath9k 2 GPIO_ACTIVE_LOW>;
+ };
+
+ power_amber: power_amber {
+ label = "netgear:amber:power";
+ gpios = <&ath9k 1 GPIO_ACTIVE_LOW>;
+ default-state = "keep";
+ };
+
+ wlan_blue {
+ label = "netgear:blue:wlan";
+ gpios = <&ath9k 0 GPIO_ACTIVE_LOW>;
+ linux,default-trigger = "phy0tpt";
+ };
+ };
+};
+
+&spi {
+ status = "okay";
+ num-cs = <1>;
+
+ flash at 0 {
+ compatible = "jedec,spi-nor";
+ reg = <0>;
+ spi-max-frequency = <25000000>;
+
+ partitions {
+ compatible = "fixed-partitions";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ partition at 0 {
+ label = "u-boot";
+ reg = <0x0 0x40000>;
+ read-only;
+ };
+
+ partition at 40000 {
+ label = "u-boot-env";
+ reg = <0x40000 0x10000>;
+ };
+
+ partition at 50000 {
+ label = "firmware";
+ reg = <0x50000 0x7a0000>;
+ compatible = "netgear,uimage";
+ };
+
+ art: partition at 7f0000 {
+ label = "art";
+ reg = <0x7f0000 0x10000>;
+ read-only;
+ };
+ };
+ };
+};
+
+ð0 {
+ status = "okay";
+
+ mtd-mac-address = <&art 0x0>;
+};
+
+ð1 {
+ status = "okay";
+
+ compatible = "qca,ar7241-eth", "syscon", "simple-mfd";
+ mtd-mac-address = <&art 0x6>;
+};
+
+&pcie {
+ status = "okay";
+
+ ath9k: wifi at 0,0 {
+ compatible = "pci168c,002e";
+ reg = <0x0000 0 0 0 0>;
+ mtd-mac-address = <&art 0x0>;
+ mtd-mac-address-increment = <1>;
+ mtd-cal-data = <&art 0x1000>;
+ qca,no-eeprom;
+ #gpio-cells = <2>;
+ gpio-controller;
+
+ usb-power {
+ gpio-hog;
+ line-name = "netgear:power:usb";
+ gpios = <4 GPIO_ACTIVE_HIGH>;
+ output-high;
+ };
+ };
+};
+
+&uart {
+ status = "okay";
+};
+
+&gpio {
+ status = "okay";
+};
+
+&usb_phy {
+ status = "okay";
+};
+
+&usb {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "okay";
+
+ hub_port: port at 1 {
+ reg = <1>;
+ #trigger-source-cells = <0>;
+ };
+};
diff --git a/target/linux/ath79/image/generic.mk b/target/linux/ath79/image/generic.mk
index 5c8826b927..cd8300eada 100644
--- a/target/linux/ath79/image/generic.mk
+++ b/target/linux/ath79/image/generic.mk
@@ -855,6 +855,20 @@ define Device/netgear_wndr3800
endef
TARGET_DEVICES += netgear_wndr3800
+define Device/netgear_wnr2200
+ ATH_SOC := ar7241
+ DEVICE_MODEL := WNR2200
+ DEVICE_PACKAGES := kmod-usb-core kmod-usb2 kmod-usb-ledtrig-usbport
+ NETGEAR_KERNEL_MAGIC := 0x32323030
+ IMAGE_SIZE := 7808k
+ IMAGE/default := append-kernel | pad-to $$$$(BLOCKSIZE) | netgear-squashfs | append-rootfs | pad-rootfs
+ IMAGES += factory-NA.img
+ IMAGE/factory-NA.img := $$(IMAGE/default) | netgear-dni NA | check-size $$$$(IMAGE_SIZE)
+ SUPPORTED_DEVICES += wnr2200
+ $(Device/netgear_ath79)
+endef
+TARGET_DEVICES += netgear_wnr2200
+
define Device/phicomm_k2t
ATH_SOC := qca9563
DEVICE_VENDOR := Phicomm
--
2.22.0
_______________________________________________
openwrt-devel mailing list
openwrt-devel at lists.openwrt.org
https://lists.openwrt.org/mailman/listinfo/openwrt-devel
More information about the openwrt-devel
mailing list