[OpenWrt-Devel] [1/4, RFCv2] net: phy: realtek: Support RTL8366RB variant

[Heiner Kallweit]

Am 28.05.2018 um 19:47 schrieb Linus Walleij:
> The RTL8366RB is an ASIC with five internal PHYs for
> LAN0..LAN3 and WAN. The PHYs are spawn off the main
> device so they can be handled in a distributed manner
> by the Realtek PHY driver. All that is really needed
> is the power save feature enablement and letting the
> PHY driver core pick up the IRQ from the switch chip.
> 
> Cc: Antti Seppälä <a.seppala at gmail.com>
> Cc: Roman Yeryomin <roman at advem.lv>
> Cc: Colin Leitner <colin.leitner at googlemail.com>
> Cc: Gabor Juhos <juhosg at openwrt.org>
> Cc: Florian Fainelli <f.fainelli at gmail.com>
> Signed-off-by: Linus Walleij <linus.walleij at linaro.org>
> ---
> ChangeLog RFCv1->RFCv2:
> - No real changes.
> ---
>  drivers/net/phy/realtek.c | 32 ++++++++++++++++++++++++++++++++
>  1 file changed, 32 insertions(+)
> 
> diff --git a/drivers/net/phy/realtek.c b/drivers/net/phy/realtek.c
> index 9f48ecf9c627..21624d1c9d38 100644
> --- a/drivers/net/phy/realtek.c
> +++ b/drivers/net/phy/realtek.c
> @@ -37,6 +37,9 @@
>  #define RTL8201F_ISR				0x1e
>  #define RTL8201F_IER				0x13
>  
> +#define RTL8366RB_POWER_SAVE	0x21
Typically PHY register addresses are 5 bits wide, is 0x21 correct
and I miss something?

> +#define RTL8366RB_POWER_SAVE_ON 0x1000
Use BIT(12) instead?

> +
>  MODULE_DESCRIPTION("Realtek PHY driver");
>  MODULE_AUTHOR("Johnson Leung");
>  MODULE_LICENSE("GPL");
> @@ -145,6 +148,22 @@ static int rtl8211f_config_init(struct phy_device *phydev)
>  	return phy_modify_paged(phydev, 0xd08, 0x11, RTL8211F_TX_DELAY, val);
>  }
>  
> +static int rtl8366rb_config_init(struct phy_device *phydev)
> +{
> +	int ret;
> +	u16 reg;
> +
> +	ret = genphy_config_init(phydev);
> +	if (ret < 0)
> +		return ret;
> +
> +	reg = phy_read(phydev, RTL8366RB_POWER_SAVE);
> +	reg |= RTL8366RB_POWER_SAVE_ON;
> +	phy_write(phydev, RTL8366RB_POWER_SAVE, reg);
return phy_set_bits(phydev, RTL8366RB_POWER_SAVE, RTL8366RB_POWER_SAVE_ON);
would be easier.

> +
> +	return 0;
> +}
> +
>  static struct phy_driver realtek_drvs[] = {
>  	{
>  		.phy_id         = 0x00008201,
> @@ -207,6 +226,18 @@ static struct phy_driver realtek_drvs[] = {
>  		.resume		= genphy_resume,
>  		.read_page	= rtl821x_read_page,
>  		.write_page	= rtl821x_write_page,
> +	}, {
> +		/* The main part of this DSA is in drivers/net/dsa */
> +		.phy_id		= 0x001cc961,
> +		.name		= "RTL8366RB Gigabit Ethernet",
> +		.phy_id_mask	= 0x001fffff,
> +		.features	= PHY_GBIT_FEATURES,
> +		.flags		= PHY_HAS_INTERRUPT,
> +		.config_aneg	= &genphy_config_aneg,
Can be omitted, genphy_config_aneg is the default since 00fde79532d6
"net: phy: core: use genphy version of callbacks read_status and
config_aneg per default".

> +		.config_init	= &rtl8366rb_config_init,
> +		.read_status	= &genphy_read_status,
Can be omitted, genphy_read_status is the default.

> +		.suspend	= genphy_suspend,
> +		.resume		= genphy_resume,
>  	},
>  };
>  
> @@ -218,6 +249,7 @@ static struct mdio_device_id __maybe_unused realtek_tbl[] = {
>  	{ 0x001cc914, 0x001fffff },
>  	{ 0x001cc915, 0x001fffff },
>  	{ 0x001cc916, 0x001fffff },
> +	{ 0x001cc961, 0x001fffff },
>  	{ }
>  };
>  
> 


_______________________________________________
openwrt-devel mailing list
openwrt-devel at lists.openwrt.org
https://lists.openwrt.org/mailman/listinfo/openwrt-devel