[OpenWrt-Devel] [PATCH 3/4] ath79: add Netgear WNR612 v2

[Rafał Miłecki]

On 13.06.2018 10:51, Zoltan HERPAI wrote:
> Netgear WNR612 v2:
>   - cpu Atheros AR7240 (Python) @400MHz
>   - flash 4MB
>   - ram 32MB
>   - ethernet 10/100: 1xwan + 2xlan (only two)
>   - radio AR9285
> 
> As there is a rebranded WNR612v2 called ON Networks N150R, add
> a dtsi which includes all device support, and add a separate dts
> for the board only (allowing for a separate one for the subsequent
> N150R).
> 
> Signed-off-by: Zoltan HERPAI <wigyori at uid0.hu>

See inline blow, please.


> diff --git a/target/linux/ath79/dts/ar7240_netgear_wnr612-v2.dtsi b/target/linux/ath79/dts/ar7240_netgear_wnr612-v2.dtsi
> new file mode 100644
> index 0000000..b86147e
> --- /dev/null
> +++ b/target/linux/ath79/dts/ar7240_netgear_wnr612-v2.dtsi
> @@ -0,0 +1,147 @@
> +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
> +/dts-v1/;
> +
> +#include <dt-bindings/gpio/gpio.h>
> +#include <dt-bindings/input/input.h>
> +
> +#include "ar7240.dtsi"
> +
> +/ {
> +	compatible = "netgear,wnr612-v2", "qca,ar7240";
> +	model = "Netgear WNR612 V2";
> +
> +	aliases {
> +		led-status = &led_power;
> +	};
> +
> +	memory at 0 {
> +		device_type = "memory";
> +		reg = <0x0 0x2000000>;
> +	};
> +
> +	gpio-keys-polled {
> +		compatible = "gpio-keys-polled";
> +		#address-cells = <1>;
> +		#size-cells = <0>;
> +		poll-interval = <20>;
> +
> +		reset {
> +			label = "reset";
> +			linux,code = <KEY_RESTART>;
> +			gpios = <&ath9k 7 GPIO_ACTIVE_LOW>;
> +			debounce-interval = <60>;
> +		};
> +	};
> +
> +	gpio-leds {
> +		compatible = "gpio-leds";
> +		led_power: power {
> +			label = "netgear:green:power";
> +			gpios = <&gpio 11 GPIO_ACTIVE_LOW>;
> +		};
> +
> +		lan1 {
> +			label = "netgear:green:lan1";
> +			gpios = <&gpio 13 GPIO_ACTIVE_LOW>;
> +		};
> +
> +		lan2 {
> +			label = "netgear:green:lan2";
> +			gpios = <&gpio 14 GPIO_ACTIVE_LOW>;
> +		};
> +
> +		wan {
> +			label = "netgear:green:wan";
> +			gpios = <&gpio 17 GPIO_ACTIVE_LOW>;
> +		};
> +
> +		wlan {
> +			label = "netgear:green:wlan";
> +			gpios = <&ath9k 1 GPIO_ACTIVE_LOW>;
> +			default-state = "off";
> +			linux,default-trigger = "phy0tpt";
> +		};
> +	};
> +};
> +
> +&spi {
> +	status = "okay";
> +	num-cs = <1>;
> +
> +	flash at 0 {
> +		#address-cells = <1>;
> +		#size-cells = <1>;
> +		compatible = "jedec,spi-nor";
> +		reg = <0>;
> +		spi-max-frequency = <25000000>;
> +
> +		partitions {
> +			compatible = "fixed-partitions";
> +			#address-cells = <1>;
> +			#size-cells = <1>;
> +
> +			uboot: partition at 0 {
> +				reg = <0x0 0x40000>;
> +				label = "u-boot";
> +				read-only;
> +			};
> +
> +			partition at 1 {
> +				reg = <0x40000 0x10000>;
> +				label = "u-boot-env";
> +			};

That @1 isn't correct, you should use partition offset. See:
Documentation/devicetree/bindings/mtd/partition.txt

Same below.


> +			partition at 2 {
> +				reg = <0x50000 0x3a0000>;
> +				label = "firmware";
> +			};
> +
> +			partition at 3 {
> +				reg = <0x3f0000 0x10000>;
> +				label = "art";
> +				read-only;
> +			};
> +		};
> +	};
> +};

_______________________________________________
openwrt-devel mailing list
openwrt-devel at lists.openwrt.org
https://lists.openwrt.org/listinfo/openwrt-devel