[OpenWrt-Devel] [PATCH] ath79: add support for GL.iNet GL-AR750S
Mathias Kresin
dev at kresin.me
Sun Dec 30 07:41:28 EST 2018
Hey,
I stumbled of some more stuff. Comments inline.
Am So., 30. Dez. 2018 um 13:27 Uhr schrieb Christoph Krapp via
openwrt-devel <openwrt-devel at lists.openwrt.org>:
>
> The sender domain has a DMARC Reject/Quarantine policy which disallows
> sending mailing list messages using the original "From" header.
>
> To mitigate this problem, the original message has been wrapped
> automatically by the mailing list software.
>
>
> ---------- Forwarded message ----------
> From: Christoph Krapp <achterin at googlemail.com>
> To: openwrt-devel at lists.openwrt.org
> Cc:
> Bcc:
> Date: Sun, 30 Dec 2018 13:26:31 +0100
> Subject: [PATCH] ath79: add support for GL.iNet GL-AR750S
> This patch adds supports for GL-AR750S.
> Right now this patch only adds nor image generation.
> NAND image generation is not supportet at the moment.
>
> Specification:
> - SOC: QCA9563 (775MHz)
> - Flash: 16 MiB (W25Q128FVSG)
> - RAM: 128 MiB DDR2
> - Ethernet: 2x 1Gbps LAN + 1x 1Gbps WAN
> - Wireless: 2.4GHz (bgn) and 5GHz (ac)
> - USB: 1x USB 2.0 port
> - Button: 1x switch button, 1x reset button
> - LED: 3x LEDS (green)
The gl.Inet webpage mentions a " TF Card Slot (128GB Max.) " as well.
Any idea if it works and how it might be connected?
>
> Flash instruction:
> - Set static ip to 192.168.1.2
> - Unplug the power cord
> - Hold reset button
> - Plug power back in
> - Right led will flash 5 times
> - Release reset button
> - Browse to 192.168.1.1
> - Choose sysupgrade image in NOR-flash section
> - Press "update nor firmware"
> - After successful transfer unplug network cable before device restarts
>
> Signed-off-by: Christoph Krapp <achterin at googlemail.com>
> ---
> .../ath79/base-files/etc/board.d/02_network | 4 +
> .../etc/hotplug.d/firmware/11-ath10k-caldata | 9 +-
> .../linux/ath79/dts/qca9563_glinet_ar750s.dts | 160 ++++++++++++++++++
> target/linux/ath79/image/generic.mk | 9 +
> 4 files changed, 178 insertions(+), 4 deletions(-)
> create mode 100644 target/linux/ath79/dts/qca9563_glinet_ar750s.dts
>
> diff --git a/target/linux/ath79/base-files/etc/board.d/02_network b/target/linux/ath79/base-files/etc/board.d/02_network
> index 004ab59573..b9a0f356bf 100755
> --- a/target/linux/ath79/base-files/etc/board.d/02_network
> +++ b/target/linux/ath79/base-files/etc/board.d/02_network
> @@ -93,6 +93,10 @@ ath79_setup_interfaces()
> glinet,gl-x750)
> ucidef_set_interfaces_lan_wan "eth1" "eth0"
> ;;
> + glinet,ar750s)
> + ucidef_add_switch "switch0" \
> + "0 at eth0" "2:lan:2" "3:lan:1" "1:wan"
> + ;;
> nec,wg800hp)
> ucidef_add_switch "switch0" \
> "0 at eth0" "2:lan" "3:lan" "4:lan" "1:wan"
> diff --git a/target/linux/ath79/base-files/etc/hotplug.d/firmware/11-ath10k-caldata b/target/linux/ath79/base-files/etc/hotplug.d/firmware/11-ath10k-caldata
> index 53f57be824..2118d2b06b 100644
> --- a/target/linux/ath79/base-files/etc/hotplug.d/firmware/11-ath10k-caldata
> +++ b/target/linux/ath79/base-files/etc/hotplug.d/firmware/11-ath10k-caldata
> @@ -92,6 +92,11 @@ case "$FIRMWARE" in
> ath10kcal_extract "art" 20480 2116
> ath10kcal_patch_mac_crc $(macaddr_add $(mtd_get_mac_binary art 0) -1)
> ;;
> + glinet,ar750s|\
> + tplink,re450-v2)
> + ath10kcal_extract "art" 20480 2116
> + ath10kcal_patch_mac $(macaddr_add $(cat /sys/class/net/eth0/address) +1)
> + ;;
> glinet,gl-x750)
> ath10kcal_extract "art" 20480 2116
> ath10kcal_patch_mac $(macaddr_add $(cat /sys/class/net/eth0/address) +1)
> @@ -122,10 +127,6 @@ case "$FIRMWARE" in
> ath10kcal_extract "art" 20480 2116
> ath10kcal_patch_mac $(macaddr_add $(cat /sys/class/net/eth0/address) -1)
> ;;
> - tplink,re450-v2)
> - ath10kcal_extract "art" 20480 2116
> - ath10kcal_patch_mac $(macaddr_add $(cat /sys/class/net/eth0/address) +1)
> - ;;
> ubnt,unifiac-lite|\
> ubnt,unifiac-mesh|\
> ubnt,unifiac-mesh-pro|\
> diff --git a/target/linux/ath79/dts/qca9563_glinet_ar750s.dts b/target/linux/ath79/dts/qca9563_glinet_ar750s.dts
> new file mode 100644
> index 0000000000..eff7aafaf6
> --- /dev/null
> +++ b/target/linux/ath79/dts/qca9563_glinet_ar750s.dts
> @@ -0,0 +1,160 @@
> +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
> +/dts-v1/;
> +
> +#include <dt-bindings/gpio/gpio.h>
> +#include <dt-bindings/input/input.h>
> +
> +#include "qca956x.dtsi"
> +
> +/ {
> + compatible = "glinet,ar750s", "qca,qca9563";
> + model = "GL.iNet GL-AR750S";
> +
> + chosen {
> + bootargs = "console=ttyS0,115200n8";
> + };
> +
> + aliases {
> + led-boot = &power;
> + led-failsafe = &power;
> + led-running = &power;
> + led-upgrade = &power;
> + };
> +
> + keys {
> + compatible = "gpio-keys-polled";
> + poll-interval = <20>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&jtag_disable_pins>;
> +
> + button0 {
> + label = "reset";
> + linux,code = <KEY_RESTART>;
> + gpios = <&gpio 2 GPIO_ACTIVE_LOW>;
> + };
> +
> + button1 {
> + label = "button right";
> + linux,code = <BTN_0>;
> + gpios = <&gpio 8 GPIO_ACTIVE_LOW>;
> + };
> +
If you have to send a third version of this patch, please drop this blank line.
> + };
> +
> + leds {
> + compatible = "gpio-leds";
> +
> + power: power {
> + label = "gl-ar750s:green:power";
> + gpios = <&gpio 1 GPIO_ACTIVE_LOW>;
> + default-state = "keep";
> + };
> +
> + usbpower {
> + label = "gl-ar750s:green:usbpower";
> + gpios = <&gpio 7 GPIO_ACTIVE_LOW>;
> + };
This still looks wrong to me. Since you mentioned only three leds in
the commit message, I assume it is a GPIO which need to be pulled to
enable or disable USB power. Please grep for gpio-export to see how it
is done right.
> +
> + wlan2g {
> + label = "gl-ar750s:green:wlan2g";
> + gpios = <&gpio 19 GPIO_ACTIVE_LOW>;
> + linux,default-trigger = "phy1tpt";
> + };
> +
> + wlan5g {
> + label = "gl-ar750s:green:wlan5g";
> + gpios = <&gpio 20 GPIO_ACTIVE_HIGH>;
> + linux,default-trigger = "phy0tpt";
> + };
> + };
> +};
> +
> +&spi {
> + status = "okay";
> + num-cs = <0>;
> +
> + flash at 0 {
> + compatible = "jedec,spi-nor";
> + reg = <0>;
> + spi-max-frequency = <25000000>;
> +
> + partitions {
> + compatible = "fixed-partitions";
> + #address-cells = <1>;
> + #size-cells = <1>;
> +
> + partition at 0 {
> + label = "u-boot";
> + reg = <0x000000 0x040000>;
> + read-only;
> + };
> +
> + partition at 40000 {
> + label = "u-boot-env";
> + reg = <0x040000 0x010000>;
> + };
> +
> + art: partition at 50000 {
> + label = "art";
> + reg = <0x050000 0x010000>;
> + };
> +
> + partition at 60000 {
> + compatible = "denx,uimage";
> + label = "firmware";
> + reg = <0x060000 0xfa0000>;
> + };
> +
If you have to send a third version of this patch, please drop this blank line.
> + };
> + };
> +};
> +
> +&pcie {
> + status = "okay";
> +};
> +
> +&uart {
> + status = "okay";
> +};
> +
> +&usb0 {
> + #address-cells = <1>;
> + #size-cells = <0>;
> + status = "okay";
> +
> + hub_port: port at 1 {
> + reg = <1>;
> + #trigger-source-cells = <0>;
> + };
> +};
> +
> +&usb_phy0 {
> + status = "okay";
> +};
> +
> +&mdio0 {
> + status = "okay";
> + phy-mask = <0>;
> +
> + phy0: ethernet-phy at 0 {
> + reg = <0>;
> + phy-mode = "sgmii";
> + qca,ar8327-initvals = <
> + 0x04 0x00080080 /* PORT0 PAD MODE CTRL */
> + 0x7c 0x0000007e /* PORT0_STATUS */
> + >;
> + };
> +};
> +
> +ð0 {
> + status = "okay";
> +
> + mtd-mac-address = <&art 0x0>;
> + phy-handle = <&phy0>;
> +};
> +
> +&wmac {
> + status = "okay";
> + mtd-cal-data = <&art 0x1000>;
> + mtd-mac-address = <&art 0x1002>;
> +};
> diff --git a/target/linux/ath79/image/generic.mk b/target/linux/ath79/image/generic.mk
> index b2f83ba58c..c61148d50e 100644
> --- a/target/linux/ath79/image/generic.mk
> +++ b/target/linux/ath79/image/generic.mk
> @@ -237,6 +237,15 @@ define Device/glinet_ar300m-nor
> endef
> TARGET_DEVICES += glinet_ar300m-nor
>
> +define Device/glinet_ar750s
> + ATH_SOC := qca9563
> + DEVICE_TITLE := GL.iNet GL-AR750S
> + DEVICE_PACKAGES := kmod-usb2 kmod-ath10k-ct ath10k-firmware-qca988x-ct
> + IMAGE_SIZE := 16000k
> + SUPPORTED_DEVICES += gl-ar750s
> +endef
> +TARGET_DEVICES += glinet_ar750s
> +
> define Device/glinet_gl-x750
> ATH_SOC := qca9531
> DEVICE_TITLE := GL.iNet GL-X750
> --
> 2.19.2
>
>
> _______________________________________________
> openwrt-devel mailing list
> openwrt-devel at lists.openwrt.org
> https://lists.openwrt.org/mailman/listinfo/openwrt-devel
_______________________________________________
openwrt-devel mailing list
openwrt-devel at lists.openwrt.org
https://lists.openwrt.org/mailman/listinfo/openwrt-devel
More information about the openwrt-devel
mailing list