[OpenWrt-Devel] Add support for AVM Fritzbox 7360 SL
Sebastian Ortwein
kron at animeland.de
Sun May 15 15:45:27 EDT 2016
Am 15.05.2016 um 17:37 schrieb Martin Blumenstingl:
> On Sun, May 15, 2016 at 3:44 PM, Sebastian Ortwein <kron at animeland.de> wrote:
>> USB, WLAN and LAN works now. The only think what would not work is phy0 &
>> phy1.
>> I have attached my lastet patch.
> if you google around a bit you'll find an AR8035 datasheet: that phy
> is from the same series as the AR8030.
> It defines that the RST pin is "active low" -> meaning you have to
> pull it high to ensure that the PHY is not being reset:
> http://lxr.free-electrons.com/source/Documentation/devicetree/bindings/pinctrl/lantiq,pinctrl-xway.txt?v=4.4#L61
> This means you should probably use:
> lantiq,output = <1>;
> lantiq,pull = <2>;
> lantiq,open-drain;
>
>> [ 0.993675] libphy: lantiq,xrx200-mdio: probed
>> [ 1.004257] eth0: attached PHY [Generic PHY] (phy_addr=0:00, irq=-1)
>> [ 1.009606] eth0: attached PHY [Generic PHY] (phy_addr=0:01, irq=-1)
>> [ 1.079564] eth0: attached PHY [Lantiq XWAY VR9 GPHY 11G v1.4]
>> (phy_addr=0:11, irq=-1)
>> [ 1.147555] eth0: attached PHY [Lantiq XWAY VR9 GPHY 11G v1.4]
>> (phy_addr=0:13, irq=-1)
> "Generic PHY" means that no specific driver for this PHY is loaded.
> Make sure you enable CONFIG_AT803X_PHY in target/linux/lantiq/config-4.4
>
> Additionally you should check the phy-mode:
> You are setting phy-mode = "rgmii", but Atheros says that the AR8030
> is an "Ultra low-power single RMII Fast Ethernet PHY".
> Thus you should probably change "rgmii" to "rmii".
>
>
> Martin
Okay thank you for support. Now all thinks works fine LAN, WIFI, Switch
and USB.
I attach my patch to add the support for OpenWRT.
Is there anything to do for including this patch in OpenWRT?
Sebastian
> On Sun, May 15, 2016 at 3:44 PM, Sebastian Ortwein <kron at animeland.de> wrote:
>> Am 08.05.2016 um 18:40 schrieb Martin Blumenstingl:
>>> On Sun, May 8, 2016 at 5:49 PM, Sebastian Ortwein <kron at animeland.de>
>>> wrote:
>>>> can I add it the following way ?
>>>> mdio at 0 {
>>>> #address-cells = <1>;
>>>> #size-cells = <0>;
>>>> compatible = "lantiq,xrx200-mdio";
>>>> phy0: ethernet-phy at 0 {
>>>> reg = <0x0>;
>>>> compatible = "lantiq,phy11g",
>>>> "ethernet-phy-ieee802.3-c22";
>>>> gpios = <&gpio 37 0>;
>>>> };
>>>> phy1: ethernet-phy at 1 {
>>>> reg = <0x1>;
>>>> compatible = "lantiq,phy11g",
>>>> "ethernet-phy-ieee802.3-c22";
>>>> gpios = <&gpio 44 0>;
>>>> };
>>>> phy11: ethernet-phy at 11 {
>>>> reg = <0x11>;
>>>> compatible = "lantiq,phy11g",
>>>> "ethernet-phy-ieee802.3-c22";
>>>> };
>>>> phy13: ethernet-phy at 13 {
>>>> reg = <0x13>;
>>>> compatible = "lantiq,phy11g",
>>>> "ethernet-phy-ieee802.3-c22";
>>>> };
>>> I think you have to name the property "reset-gpios", but apart from
>>> that it looks good.
>> I have try it like you sayed. But without success.
>> I think the gpios are defined here, but it won't working.
>>
>> phy-rst {
>> lantiq,pins = "io37", "io44";
>> lantiq,pull = <0>;
>> lantiq,open-drain = <0>;
>> lantiq,output = <1>;
>> };
>>
>>>>> I cannot see any ath9k messages in your kernel log - are you sure it's
>>>>> being installed (/lib/modules/*/ath9k.ko)?
>>>>> Your first patch lists kmod-ath9k, but if you added that after you
>>>>> generated your .config then you're probably still missing it.
>>>>> Please check "grep kmod-ath9k .config" and enable (set it to
>>>>> =y/built-in) it if it's missing.
>>>> I have not disable the ath9k driver. it is present and loaded.
>>> I think I see the problem after looking at your .dts again:
>>> you *must* specify the ath,pci-slot property, otherwise the fixup is
>>> not executed.
>>> It seems that the wifi part is similar to the TD-W8980 (AR9287 behind
>>> the PCIe-to-PCI bridge), so "0" should be the right value.
>>> (otherwise it's pretty easy to find out by looking at sysfs:
>>> /sys/bus/pci/devices/0000\:00\:0e.0/ -> that's where the ath9k device
>>> on HH5A can be found, there we use ath,pci-slot = <0xe>;)
>>>
>>>
>>> Martin
>>>
>>>
>>> [0]
>>> https://github.com/openwrt/openwrt/blob/master/target/linux/lantiq/patches-4.4/0035-owrt-lantiq-wifi-and-ethernet-eeprom-handling.patch#L178
>>
>> USB, WLAN and LAN works now. The only think what would not work is phy0 &
>> phy1.
>> I have attached my lastet patch.
>>
>> dmesg
>>
>> [ 0.000000] Linux version 4.4.7 (sebastian at sebastian-desktop) (gcc
>> version 5.3.0 (OpenWrt GCC 5.3.0 r49377) ) #1 Sun May 15 13:18:03 UTC 2016
>> [ 0.000000] SoC: xRX200 rev 1.1
>> [ 0.000000] bootconsole [early0] enabled
>> [ 0.000000] CPU0 revision is: 00019555 (MIPS 34Kc)
>> [ 0.000000] MIPS: machine is FRITZ7360SL - 1&1 HomeServer
>> [ 0.000000] Determined physical RAM map:
>> [ 0.000000] memory: 08000000 @ 00000000 (usable)
>> [ 0.000000] Initrd not found or empty - disabling initrd
>> [ 0.000000] Zone ranges:
>> [ 0.000000] Normal [mem 0x0000000000000000-0x0000000007ffffff]
>> [ 0.000000] Movable zone start for each node
>> [ 0.000000] Early memory node ranges
>> [ 0.000000] node 0: [mem 0x0000000000000000-0x0000000007ffffff]
>> [ 0.000000] Initmem setup node 0 [mem
>> 0x0000000000000000-0x0000000007ffffff]
>> [ 0.000000] On node 0 totalpages: 32768
>> [ 0.000000] free_area_init_node: node 0, pgdat 804d6390, node_mem_map
>> 81007b60
>> [ 0.000000] Normal zone: 256 pages used for memmap
>> [ 0.000000] Normal zone: 0 pages reserved
>> [ 0.000000] Normal zone: 32768 pages, LIFO batch:7
>> [ 0.000000] Primary instruction cache 32kB, VIPT, 4-way, linesize 32
>> bytes.
>> [ 0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize
>> 32 bytes
>> [ 0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
>> [ 0.000000] pcpu-alloc: [0] 0
>> [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total
>> pages: 32512
>> [ 0.000000] Kernel command line: console=ttyLTQ0,115200 init=/etc/preinit
>> [ 0.000000] PID hash table entries: 512 (order: -1, 2048 bytes)
>> [ 0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536
>> bytes)
>> [ 0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
>> [ 0.000000] Writing ErrCtl register=00074200
>> [ 0.000000] Readback ErrCtl register=00074200
>> [ 0.000000] Memory: 123372K/131072K available (3764K kernel code, 164K
>> rwdata, 1144K rodata, 1184K init, 211K bss, 7700K reserved, 0K cma-reserved)
>> [ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
>> [ 0.000000] NR_IRQS:256
>> [ 0.000000] CPU Clock: 500MHz
>> [ 0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff,
>> max_idle_ns: 7645041786 ns
>> [ 0.000011] sched_clock: 32 bits at 250MHz, resolution 4ns, wraps every
>> 8589934590ns
>> [ 0.007861] Calibrating delay loop... 332.54 BogoMIPS (lpj=665088)
>> [ 0.042318] pid_max: default: 32768 minimum: 301
>> [ 0.047172] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
>> [ 0.053732] Mountpoint-cache hash table entries: 1024 (order: 0, 4096
>> bytes)
>> [ 0.066701] clocksource: jiffies: mask: 0xffffffff max_cycles:
>> 0xffffffff, max_idle_ns: 7645041785100000 ns
>> [ 0.076483] pinctrl core: initialized pinctrl subsystem
>> [ 0.082366] NET: Registered protocol family 16
>> [ 0.091505] pinctrl-xway 1e100b10.pinmux: Init done
>> [ 0.097056] dma-xway 1e104100.dma: Init done - hw rev: 7, ports: 7,
>> channels: 28
>> [ 0.207159] dcdc-xrx200 1f106a00.dcdc: Core Voltage : 1016 mV
>> [ 0.333371] ath9k,eeprom ath9k_eep: failed to load eeprom address
>> [ 0.354429] usbcore: registered new interface driver usbfs
>> [ 0.359938] usbcore: registered new interface driver hub
>> [ 0.365292] usbcore: registered new device driver usb
>> [ 0.370641] PCI host bridge to bus 0000:00
>> [ 0.374631] pci_bus 0000:00: root bus resource [mem 0x1c000000-0x1cffffff]
>> [ 0.381545] pci_bus 0000:00: root bus resource [io 0x1d800000-0x1d8fffff]
>> [ 0.388488] pci_bus 0000:00: root bus resource [??? 0x00000000 flags 0x0]
>> [ 0.395343] pci_bus 0000:00: No busn resource found for root bus, will use
>> [bus 00-ff]
>> [ 0.403373] pci 0000:00:00.0: [15d1:0011] type 01 class 0x060000
>> [ 0.403410] ifx_pcie_rc_class_early_fixup: fixed pcie host bridge to pci-pci
>> bridge
>> [ 0.421054] ifx_pcie_fixup_resource: fixup host controller 0000:00:00.0
>> (15d1:0011)
>> [ 0.428645] pci 0000:00:00.0: PME# supported from D0 D3hot
>> [ 0.429208] pci 0000:01:00.0: [168c:ff1c] type 00 class 0x020000
>> [ 0.429298] pci 0000:01:00.0: reg 0x10: [mem 0x00000000-0x0000ffff 64bit]
>> [ 0.429454] pci 0000:01:00.0: supports D1
>> [ 0.429475] pci 0000:01:00.0: PME# supported from D0 D1 D3hot
>> [ 0.429773] pci_bus 0000:01: busn_res: [bus 01-ff] end is updated to 01
>> [ 0.429814] pci_bus 0000:00: busn_res: [bus 00-ff] end is updated to 01
>> [ 0.429870] pci 0000:00:00.0: BAR 8: assigned [mem 0x1c000000-0x1c0fffff]
>> [ 0.436557] pci 0000:01:00.0: BAR 0: assigned [mem 0x1c000000-0x1c00ffff
>> 64bit]
>> [ 0.443919] pci 0000:00:00.0: PCI bridge to [bus 01]
>> [ 0.448935] pci 0000:00:00.0: bridge window [mem 0x1c000000-0x1c0fffff]
>> [ 0.455810] ifx_pcie_bios_map_irq port 0 dev 0000:00:00.0 slot 0 pin 1
>> [ 0.462461] ifx_pcie_bios_map_irq dev 0000:00:00.0 irq 144 assigned
>> [ 0.468815] ifx_pcie_bios_map_irq port 0 dev 0000:01:00.0 slot 0 pin 1
>> [ 0.475481] ifx_pcie_bios_map_irq dev 0000:01:00.0 irq 144 assigned
>> [ 0.482864] clocksource: Switched to clocksource MIPS
>> [ 0.489513] NET: Registered protocol family 2
>> [ 0.494738] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
>> [ 0.501634] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
>> [ 0.508012] TCP: Hash tables configured (established 1024 bind 1024)
>> [ 0.514529] UDP hash table entries: 256 (order: 0, 4096 bytes)
>> [ 0.520367] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
>> [ 0.526969] NET: Registered protocol family 1
>> [ 0.531315] PCI: CLS 0 bytes, default 32
>> [ 0.531770] gptu: totally 6 16-bit timers/counters
>> [ 0.536615] gptu: misc_register on minor 63
>> [ 0.540712] gptu: succeeded to request irq 126
>> [ 0.545201] gptu: succeeded to request irq 127
>> [ 0.549715] gptu: succeeded to request irq 128
>> [ 0.554229] gptu: succeeded to request irq 129
>> [ 0.558742] gptu: succeeded to request irq 130
>> [ 0.563259] gptu: succeeded to request irq 131
>> [ 0.568633] phy-xrx200 gphy-xrx200: requesting lantiq/vr9_phy11g_a1x.bin
>> [ 0.575912] phy-xrx200 gphy-xrx200: booting GPHY0 firmware at 7960000
>> [ 0.582260] phy-xrx200 gphy-xrx200: booting GPHY1 firmware at 7960000
>> [ 0.689806] futex hash table entries: 256 (order: -1, 3072 bytes)
>> [ 0.723154] squashfs: version 4.0 (2009/01/31) Phillip Lougher
>> [ 0.728894] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME)
>> (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
>> [ 0.742291] io scheduler noop registered
>> [ 0.746134] io scheduler deadline registered (default)
>> [ 0.751978] 1e100c00.serial: ttyLTQ0 at MMIO 0x1e100c00 (irq = 112,
>> base_baud = 0) is a lantiq,asc
>> [ 0.760881] console [ttyLTQ0] enabled
>> [ 0.768206] bootconsole [early0] disabled
>> [ 0.777268] lantiq nor flash device: 01000000 at 10000000
>> [ 0.781402] ltq_nor: Found 1 x16 devices at 0x0 in 16-bit bank. Manufacturer
>> ID 0x000001 Chip ID 0x002101
>> [ 0.790840] Amd/Fujitsu Extended Query Table at 0x0040
>> [ 0.795967] Amd/Fujitsu Extended Query version 1.3.
>> [ 0.801004] number of CFI chips: 1
>> [ 0.804436] 4 ofpart partitions found on MTD device ltq_nor
>> [ 0.809969] Creating 4 MTD partitions on "ltq_nor":
>> [ 0.814852] 0x000000000000-0x000000020000 : "urlader"
>> [ 0.823305] 0x000000020000-0x000000f80000 : "firmware"
>> [ 0.844284] 2 eva-fw partitions found on MTD device firmware
>> [ 0.848534] 0x000000020000-0x0000001bfa70 : "kernel"
>> [ 0.855348] 0x0000001c0100-0x000000f80000 : "rootfs"
>> [ 0.860994] mtd: device 3 (rootfs) set to be root filesystem
>> [ 0.865302] 1 squashfs-split partitions found on MTD device rootfs
>> [ 0.871420] 0x0000003e0000-0x000000f80000 : "rootfs_data"
>> [ 0.879057] 0x000000f80000-0x000000fc0000 : "tffs (1)"
>> [ 0.884936] 0x000000fc0000-0x000001000000 : "tffs (2)"
>> [ 0.993675] libphy: lantiq,xrx200-mdio: probed
>> [ 1.004257] eth0: attached PHY [Generic PHY] (phy_addr=0:00, irq=-1)
>> [ 1.009606] eth0: attached PHY [Generic PHY] (phy_addr=0:01, irq=-1)
>> [ 1.079564] eth0: attached PHY [Lantiq XWAY VR9 GPHY 11G v1.4]
>> (phy_addr=0:11, irq=-1)
>> [ 1.147555] eth0: attached PHY [Lantiq XWAY VR9 GPHY 11G v1.4]
>> (phy_addr=0:13, irq=-1)
>> [ 1.155438] wdt 1f8803f0.watchdog: Init done
>> [ 1.161244] NET: Registered protocol family 10
>> [ 1.169748] NET: Registered protocol family 17
>> [ 1.172899] bridge: automatic filtering via arp/ip/ip6tables has been
>> deprecated. Update your scripts to load br_netfilter if you need this.
>> [ 1.185425] 8021q: 802.1Q VLAN Support v1.8
>> [ 1.189680] found entry name -> annex=B
>> [ 1.193440] found entry name -> maca=BC:05:43:D7:1E:7C
>> [ 1.198534] found entry name -> macb=BC:05:43:D7:1E:7D
>> [ 1.203673] found entry name -> macwlan=BC:05:43:D7:1E:7E
>> [ 1.209066] found entry name -> macdsl=BC:05:43:D7:1E:7F
>> [ 1.214430] found entry name -> macwlan2=BC:05:43:D7:1E:81
>> [ 1.219861] found entry name -> wlan_key=4004584479108575
>> [ 1.228307] ath9k,eeprom ath9k_eep: endian check enabled.
>> [ 1.232282] ath9k,eeprom ath9k_eep: using random mac
>> [ 1.237274] ath9k,eeprom ath9k_eep: pci slot: 0
>> [ 1.241777] pci 0000:01:00.0: fixup device configuration
>> [ 1.247149] PCI: Enabling device 0000:01:00.0 (0000 -> 0002)
>> [ 1.254428] pci 0000:01:00.0: fixup info: [168c:002e] revision 01 class
>> 0x028000
>> [ 1.260435] ath9k,eeprom ath9k_eep: loaded ath9k eeprom
>> [ 1.270378] UBIFS error (pid: 1): cannot open "ubi0:rootfs", error -19
>> [ 1.280211] VFS: Mounted root (squashfs filesystem) readonly on device
>> 31:3.
>> [ 1.287767] Freeing unused kernel memory: 1184K (804f8000 - 80620000)
>> [ 2.468013] init: Console is alive
>> [ 2.470263] init: - watchdog -
>> [ 3.884244] dwc2 1e101000.ifxhcd: Configuration mismatch. Forcing host
>> mode
>> [ 4.035028] eth0: port 0 got link
>> [ 4.747073] dwc2 1e101000.ifxhcd: DWC OTG Controller
>> [ 4.750648] dwc2 1e101000.ifxhcd: new USB bus registered, assigned bus
>> number 1
>> [ 4.757999] dwc2 1e101000.ifxhcd: irq 62, io mem 0x00000000
>> [ 4.763516] dwc2 1e101000.ifxhcd: Hardware does not support descriptor
>> DMA mode -
>> [ 4.770953] dwc2 1e101000.ifxhcd: falling back to buffer DMA mode.
>> [ 4.778435] hub 1-0:1.0: USB hub found
>> [ 4.781398] hub 1-0:1.0: 1 port detected
>> [ 4.785460] dwc2 1e106000.ifxhcd: Configuration mismatch. Forcing host
>> mode
>> [ 5.647060] dwc2 1e106000.ifxhcd: DWC OTG Controller
>> [ 5.650655] dwc2 1e106000.ifxhcd: new USB bus registered, assigned bus
>> number 2
>> [ 5.657970] dwc2 1e106000.ifxhcd: irq 91, io mem 0x00000000
>> [ 5.663499] dwc2 1e106000.ifxhcd: Hardware does not support descriptor
>> DMA mode -
>> [ 5.670938] dwc2 1e106000.ifxhcd: falling back to buffer DMA mode.
>> [ 5.678440] hub 2-0:1.0: USB hub found
>> [ 5.681390] hub 2-0:1.0: 1 port detected
>> [ 5.687615] init: - preinit -
>> [ 6.192804] random: procd urandom read with 26 bits of entropy available
>> [ 8.569614] jffs2: notice: (370) jffs2_build_xattr_subsystem: complete
>> building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref
>> (0 dead, 0 orphan) found.
>> [ 8.585353] mount_root: switching to jffs2 overlay
>> [ 8.606254] procd: - early -
>> [ 8.607917] procd: - watchdog -
>> [ 9.348938] procd: - ubus -
>> [ 9.403903] procd: - init -
>> [ 10.231370] IFXOS, Version 1.5.19 (c) Copyright 2009, Lantiq Deutschland
>> GmbH
>> [ 10.241461] NET: Registered protocol family 8
>> [ 10.244431] NET: Registered protocol family 20
>> [ 10.255629] PPP generic driver version 2.4.2
>> [ 10.266429] ip6_tables: (C) 2000-2006 Netfilter Core Team
>> [ 10.291707] Lantiq (VRX) DSL CPE MEI driver, version 1.4.8.5, (c) 2013
>> Lantiq Deutschland GmbH
>> [ 10.291707]
>> [ 10.291707] Lantiq CPE API Driver version: DSL CPE API V4.16.6.3
>> [ 10.312794]
>> [ 10.312794] Predefined debug level: 3
>> [ 10.323452] Loading modules backported from Linux version
>> v4.4-rc5-1913-gc8fdf68
>> [ 10.329464] Backport generated by backports.git
>> backports-20151218-0-g2f58d9d
>> [ 10.340031] ip_tables: (C) 2000-2006 Netfilter Core Team
>> [ 10.351117] Infineon Technologies DEU driver version 2.0.0
>> [ 10.357203] IFX DEU DES initialized (multiblock).
>> [ 10.361497] IFX DEU AES initialized (multiblock).
>> [ 10.365620] IFX DEU ARC4 initialized (multiblock).
>> [ 10.370239] IFX DEU SHA1 initialized.
>> [ 10.373843] IFX DEU MD5 initialized.
>> [ 10.377438] IFX DEU SHA1_HMAC initialized.
>> [ 10.381556] IFX DEU MD5_HMAC initialized.
>> [ 10.391907] nf_conntrack version 0.5.0 (1946 buckets, 7784 max)
>> [ 10.418114] NET: Registered protocol family 24
>> [ 10.443723] xt_time: kernel timezone is -0000
>> [ 10.539595] PCI: Enabling device 0000:01:00.0 (0140 -> 0142)
>> [ 10.550629] ath: EEPROM regdomain: 0x8114
>> [ 10.550653] ath: EEPROM indicates we should expect a country code
>> [ 10.550667] ath: doing EEPROM country->regdmn map search
>> [ 10.550679] ath: country maps to regdmn code: 0x37
>> [ 10.550692] ath: Country alpha2 being used: DE
>> [ 10.550704] ath: Regpair used: 0x37
>> [ 10.564122] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
>> [ 10.567111] ieee80211 phy0: Atheros AR9287 Rev:2 mem=0xbc000000, irq=144
>> [ 19.477228] device eth0.1 entered promiscuous mode
>> [ 19.480651] device eth0 entered promiscuous mode
>> [ 19.500394] br-lan: port 1(eth0.1) entered forwarding state
>> [ 19.504638] br-lan: port 1(eth0.1) entered forwarding state
>> [ 21.506873] br-lan: port 1(eth0.1) entered forwarding state
>> [ 31.802908] random: nonblocking pool is initialized
>>
>>
>> logread
>>
>> hu May 12 05:36:24 2016 kern.info kernel: [ 0.381545] pci_bus 0000:00: root
>> bus resource [io 0x1d800000-0x1d8fffff]
>> Thu May 12 05:36:24 2016 kern.info kernel: [ 0.388488] pci_bus 0000:00: root
>> bus resource [??? 0x00000000 flags 0x0]
>> Thu May 12 05:36:24 2016 kern.info kernel: [ 0.395343] pci_bus 0000:00: No
>> busn resource found for root bus, will use [bus 00-ff]
>> Thu May 12 05:36:24 2016 kern.debug kernel: [ 0.403373] pci 0000:00:00.0:
>> [15d1:0011] type 01 class 0x060000
>> Thu May 12 05:36:24 2016 kern.info kernel: [ 0.403410]
>> ifx_pcie_rc_class_early_fixup: fixed pcie host bridge to pci-pci bridge
>> Thu May 12 05:36:24 2016 kern.warn kernel: [ 0.421054]
>> ifx_pcie_fixup_resource: fixup host controller 0000:00:00.0 (15d1:0011)
>> Thu May 12 05:36:24 2016 kern.debug kernel: [ 0.428645] pci 0000:00:00.0:
>> PME# supported from D0 D3hot
>> Thu May 12 05:36:24 2016 kern.debug kernel: [ 0.429208] pci 0000:01:00.0:
>> [168c:ff1c] type 00 class 0x020000
>> Thu May 12 05:36:24 2016 kern.debug kernel: [ 0.429298] pci 0000:01:00.0:
>> reg 0x10: [mem 0x00000000-0x0000ffff 64bit]
>> Thu May 12 05:36:24 2016 kern.debug kernel: [ 0.429454] pci 0000:01:00.0:
>> supports D1
>> Thu May 12 05:36:24 2016 kern.debug kernel: [ 0.429475] pci 0000:01:00.0:
>> PME# supported from D0 D1 D3hot
>> Thu May 12 05:36:24 2016 kern.debug kernel: [ 0.429773] pci_bus 0000:01:
>> busn_res: [bus 01-ff] end is updated to 01
>> Thu May 12 05:36:24 2016 kern.debug kernel: [ 0.429814] pci_bus 0000:00:
>> busn_res: [bus 00-ff] end is updated to 01
>> Thu May 12 05:36:24 2016 kern.info kernel: [ 0.429870] pci 0000:00:00.0: BAR
>> 8: assigned [mem 0x1c000000-0x1c0fffff]
>> Thu May 12 05:36:24 2016 kern.info kernel: [ 0.436557] pci 0000:01:00.0: BAR
>> 0: assigned [mem 0x1c000000-0x1c00ffff 64bit]
>> Thu May 12 05:36:24 2016 kern.info kernel: [ 0.443919] pci 0000:00:00.0: PCI
>> bridge to [bus 01]
>> Thu May 12 05:36:24 2016 kern.info kernel: [ 0.448935] pci 0000:00:00.0:
>> bridge window [mem 0x1c000000-0x1c0fffff]
>> Thu May 12 05:36:24 2016 kern.warn kernel: [ 0.455810] ifx_pcie_bios_map_irq
>> port 0 dev 0000:00:00.0 slot 0 pin 1
>> Thu May 12 05:36:24 2016 kern.warn kernel: [ 0.462461] ifx_pcie_bios_map_irq
>> dev 0000:00:00.0 irq 144 assigned
>> Thu May 12 05:36:24 2016 kern.warn kernel: [ 0.468815] ifx_pcie_bios_map_irq
>> port 0 dev 0000:01:00.0 slot 0 pin 1
>> Thu May 12 05:36:24 2016 kern.warn kernel: [ 0.475481] ifx_pcie_bios_map_irq
>> dev 0000:01:00.0 irq 144 assigned
>> Thu May 12 05:36:24 2016 kern.info kernel: [ 0.482864] clocksource: Switched
>> to clocksource MIPS
>> Thu May 12 05:36:24 2016 kern.info kernel: [ 0.489513] NET: Registered
>> protocol family 2
>> Thu May 12 05:36:24 2016 kern.info kernel: [ 0.494738] TCP established hash
>> table entries: 1024 (order: 0, 4096 bytes)
>> Thu May 12 05:36:24 2016 kern.info kernel: [ 0.501634] TCP bind hash
>> table entries: 1024 (order: 0, 4096 bytes)
>> Thu May 12 05:36:24 2016 kern.info kernel: [ 0.508012] TCP: Hash tables
>> configured (established 1024 bind 1024)
>> Thu May 12 05:36:24 2016 kern.info kernel: [ 0.514529] UDP hash table
>> entries: 256 (order: 0, 4096 bytes)
>> Thu May 12 05:36:24 2016 kern.info kernel: [ 0.520367] UDP-Lite hash table
>> entries: 256 (order: 0, 4096 bytes)
>> Thu May 12 05:36:24 2016 kern.info kernel: [ 0.526969] NET: Registered
>> protocol family 1
>> Thu May 12 05:36:24 2016 kern.debug kernel: [ 0.531315] PCI: CLS 0 bytes,
>> default 32
>> Thu May 12 05:36:24 2016 kern.info kernel: [ 0.531770] gptu: totally 6
>> 16-bit timers/counters
>> Thu May 12 05:36:24 2016 kern.info kernel: [ 0.536615] gptu: misc_register
>> on minor 63
>> Thu May 12 05:36:24 2016 kern.info kernel: [ 0.540712] gptu: succeeded to
>> request irq 126
>> Thu May 12 05:36:24 2016 kern.info kernel: [ 0.545201] gptu: succeeded to
>> request irq 127
>> Thu May 12 05:36:24 2016 kern.info kernel: [ 0.549715] gptu: succeeded to
>> request irq 128
>> Thu May 12 05:36:24 2016 kern.info kernel: [ 0.554229] gptu: succeeded to
>> request irq 129
>> Thu May 12 05:36:24 2016 kern.info kernel: [ 0.558742] gptu: succeeded to
>> request irq 130
>> Thu May 12 05:36:24 2016 kern.info kernel: [ 0.563259] gptu: succeeded to
>> request irq 131
>> Thu May 12 05:36:24 2016 kern.info kernel: [ 0.568633] phy-xrx200
>> gphy-xrx200: requesting lantiq/vr9_phy11g_a1x.bin
>> Thu May 12 05:36:24 2016 kern.info kernel: [ 0.575912] phy-xrx200
>> gphy-xrx200: booting GPHY0 firmware at 7960000
>> Thu May 12 05:36:24 2016 kern.info kernel: [ 0.582260] phy-xrx200
>> gphy-xrx200: booting GPHY1 firmware at 7960000
>> Thu May 12 05:36:24 2016 kern.info kernel: [ 0.689806] futex hash table
>> entries: 256 (order: -1, 3072 bytes)
>> Thu May 12 05:36:24 2016 kern.info kernel: [ 0.723154] squashfs: version 4.0
>> (2009/01/31) Phillip Lougher
>> Thu May 12 05:36:24 2016 kern.info kernel: [ 0.728894] jffs2: version 2.2
>> (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
>> Thu May 12 05:36:24 2016 kern.info kernel: [ 0.742291] io scheduler noop
>> registered
>> Thu May 12 05:36:24 2016 kern.info kernel: [ 0.746134] io scheduler deadline
>> registered (default)
>> Thu May 12 05:36:24 2016 kern.info kernel: [ 0.751978] 1e100c00.serial:
>> ttyLTQ0 at MMIO 0x1e100c00 (irq = 112, base_baud = 0) is a lantiq,asc
>> Thu May 12 05:36:24 2016 kern.info kernel: [ 0.760881] console [ttyLTQ0]
>> enabled
>> Thu May 12 05:36:24 2016 kern.info kernel: [ 0.768206] bootconsole [early0]
>> disabled
>> Thu May 12 05:36:24 2016 kern.notice kernel: [ 0.777268] lantiq nor flash
>> device: 01000000 at 10000000
>> Thu May 12 05:36:24 2016 kern.info kernel: [ 0.781402] ltq_nor: Found 1 x16
>> devices at 0x0 in 16-bit bank. Manufacturer ID 0x000001 Chip ID 0x002101
>> Thu May 12 05:36:24 2016 kern.info kernel: [ 0.790840] Amd/Fujitsu Extended
>> Query Table at 0x0040
>> Thu May 12 05:36:24 2016 kern.info kernel: [ 0.795967] Amd/Fujitsu Extended
>> Query version 1.3.
>> Thu May 12 05:36:24 2016 kern.notice kernel: [ 0.801004] number of CFI
>> chips: 1
>> Thu May 12 05:36:24 2016 kern.notice kernel: [ 0.804436] 4 ofpart partitions
>> found on MTD device ltq_nor
>> Thu May 12 05:36:24 2016 kern.notice kernel: [ 0.809969] Creating 4 MTD
>> partitions on "ltq_nor":
>> Thu May 12 05:36:24 2016 kern.notice kernel: [ 0.814852]
>> 0x000000000000-0x000000020000 : "urlader"
>> Thu May 12 05:36:24 2016 kern.notice kernel: [ 0.823305]
>> 0x000000020000-0x000000f80000 : "firmware"
>> Thu May 12 05:36:24 2016 kern.notice kernel: [ 0.844284] 2 eva-fw partitions
>> found on MTD device firmware
>> Thu May 12 05:36:24 2016 kern.notice kernel: [ 0.848534]
>> 0x000000020000-0x0000001bfa70 : "kernel"
>> Thu May 12 05:36:24 2016 kern.notice kernel: [ 0.855348]
>> 0x0000001c0100-0x000000f80000 : "rootfs"
>> Thu May 12 05:36:24 2016 kern.notice kernel: [ 0.860994] mtd: device 3
>> (rootfs) set to be root filesystem
>> Thu May 12 05:36:24 2016 kern.notice kernel: [ 0.865302] 1 squashfs-split
>> partitions found on MTD device rootfs
>> Thu May 12 05:36:24 2016 kern.notice kernel: [ 0.871420]
>> 0x0000003e0000-0x000000f80000 : "rootfs_data"
>> Thu May 12 05:36:24 2016 kern.notice kernel: [ 0.879057]
>> 0x000000f80000-0x000000fc0000 : "tffs (1)"
>> Thu May 12 05:36:24 2016 kern.notice kernel: [ 0.884936]
>> 0x000000fc0000-0x000001000000 : "tffs (2)"
>> Thu May 12 05:36:24 2016 kern.info kernel: [ 0.993675] libphy:
>> lantiq,xrx200-mdio: probed
>> Thu May 12 05:36:24 2016 kern.info kernel: [ 1.004257] eth0: attached PHY
>> [Generic PHY] (phy_addr=0:00, irq=-1)
>> Thu May 12 05:36:24 2016 kern.info kernel: [ 1.009606] eth0: attached PHY
>> [Generic PHY] (phy_addr=0:01, irq=-1)
>> Thu May 12 05:36:24 2016 kern.info kernel: [ 1.079564] eth0: attached PHY
>> [Lantiq XWAY VR9 GPHY 11G v1.4] (phy_addr=0:11, irq=-1)
>> Thu May 12 05:36:24 2016 kern.info kernel: [ 1.147555] eth0: attached PHY
>> [Lantiq XWAY VR9 GPHY 11G v1.4] (phy_addr=0:13, irq=-1)
>> Thu May 12 05:36:24 2016 kern.info kernel: [ 1.155438] wdt
>> 1f8803f0.watchdog: Init done
>> Thu May 12 05:36:24 2016 kern.info kernel: [ 1.161244] NET: Registered
>> protocol family 10
>> Thu May 12 05:36:24 2016 kern.info kernel: [ 1.169748] NET: Registered
>> protocol family 17
>> Thu May 12 05:36:24 2016 kern.info kernel: [ 1.172899] bridge: automatic
>> filtering via arp/ip/ip6tables has been deprecated. Update your scripts to
>> load br_netfilter if you need this.
>> Thu May 12 05:36:24 2016 kern.info kernel: [ 1.185425] 8021q: 802.1Q VLAN
>> Support v1.8
>> Thu May 12 05:36:24 2016 kern.info kernel: [ 1.189680] found entry name
>> -> annex=B
>> Thu May 12 05:36:24 2016 kern.info kernel: [ 1.193440] found entry name
>> -> maca=BC:05:43:D7:1E:7C
>> Thu May 12 05:36:24 2016 kern.info kernel: [ 1.198534] found entry name
>> -> macb=BC:05:43:D7:1E:7D
>> Thu May 12 05:36:24 2016 kern.info kernel: [ 1.203673] found entry name
>> -> macwlan=BC:05:43:D7:1E:7E
>> Thu May 12 05:36:24 2016 kern.info kernel: [ 1.209066] found entry name
>> -> macdsl=BC:05:43:D7:1E:7F
>> Thu May 12 05:36:24 2016 kern.info kernel: [ 1.214430] found entry name
>> -> macwlan2=BC:05:43:D7:1E:81
>> Thu May 12 05:36:24 2016 kern.info kernel: [ 1.219861] found entry name
>> -> wlan_key=4004584479108575
>> Thu May 12 05:36:24 2016 kern.info kernel: [ 1.228307] ath9k,eeprom
>> ath9k_eep: endian check enabled.
>> Thu May 12 05:36:24 2016 kern.warn kernel: [ 1.232282] ath9k,eeprom
>> ath9k_eep: using random mac
>> Thu May 12 05:36:24 2016 kern.info kernel: [ 1.237274] ath9k,eeprom
>> ath9k_eep: pci slot: 0
>> Thu May 12 05:36:24 2016 kern.info kernel: [ 1.241777] pci 0000:01:00.0:
>> fixup device configuration
>> Thu May 12 05:36:24 2016 kern.warn kernel: [ 1.247149] PCI: Enabling
>> device 0000:01:00.0 (0000 -> 0002)
>> Thu May 12 05:36:24 2016 kern.info kernel: [ 1.254428] pci 0000:01:00.0:
>> fixup info: [168c:002e] revision 01 class 0x028000
>> Thu May 12 05:36:24 2016 kern.info kernel: [ 1.260435] ath9k,eeprom
>> ath9k_eep: loaded ath9k eeprom
>> Thu May 12 05:36:24 2016 kern.err kernel: [ 1.270378] UBIFS error (pid:
>> 1): cannot open "ubi0:rootfs", error -19
>> Thu May 12 05:36:24 2016 kern.info kernel: [ 1.280211] VFS: Mounted root
>> (squashfs filesystem) readonly on device 31:3.
>> Thu May 12 05:36:24 2016 kern.info kernel: [ 1.287767] Freeing unused
>> kernel memory: 1184K (804f8000 - 80620000)
>> Thu May 12 05:36:24 2016 user.info kernel: [ 2.468013] init: Console is
>> alive
>> Thu May 12 05:36:24 2016 user.info kernel: [ 2.470263] init: - watchdog -
>> Thu May 12 05:36:24 2016 kern.warn kernel: [ 3.884244] dwc2
>> 1e101000.ifxhcd: Configuration mismatch. Forcing host mode
>> Thu May 12 05:36:24 2016 kern.info kernel: [ 4.035028] eth0: port 0 got
>> link
>> Thu May 12 05:36:24 2016 kern.info kernel: [ 4.747073] dwc2
>> 1e101000.ifxhcd: DWC OTG Controller
>> Thu May 12 05:36:24 2016 kern.info kernel: [ 4.750648] dwc2
>> 1e101000.ifxhcd: new USB bus registered, assigned bus number 1
>> Thu May 12 05:36:24 2016 kern.info kernel: [ 4.757999] dwc2
>> 1e101000.ifxhcd: irq 62, io mem 0x00000000
>> Thu May 12 05:36:24 2016 kern.err kernel: [ 4.763516] dwc2
>> 1e101000.ifxhcd: Hardware does not support descriptor DMA mode -
>> Thu May 12 05:36:24 2016 kern.err kernel: [ 4.770953] dwc2
>> 1e101000.ifxhcd: falling back to buffer DMA mode.
>> Thu May 12 05:36:24 2016 kern.info kernel: [ 4.778435] hub 1-0:1.0: USB
>> hub found
>> Thu May 12 05:36:24 2016 kern.info kernel: [ 4.781398] hub 1-0:1.0: 1
>> port detected
>> Thu May 12 05:36:24 2016 kern.warn kernel: [ 4.785460] dwc2
>> 1e106000.ifxhcd: Configuration mismatch. Forcing host mode
>> Thu May 12 05:36:24 2016 kern.info kernel: [ 5.647060] dwc2
>> 1e106000.ifxhcd: DWC OTG Controller
>> Thu May 12 05:36:24 2016 kern.info kernel: [ 5.650655] dwc2
>> 1e106000.ifxhcd: new USB bus registered, assigned bus number 2
>> Thu May 12 05:36:24 2016 kern.info kernel: [ 5.657970] dwc2
>> 1e106000.ifxhcd: irq 91, io mem 0x00000000
>> Thu May 12 05:36:24 2016 kern.err kernel: [ 5.663499] dwc2
>> 1e106000.ifxhcd: Hardware does not support descriptor DMA mode -
>> Thu May 12 05:36:24 2016 kern.err kernel: [ 5.670938] dwc2
>> 1e106000.ifxhcd: falling back to buffer DMA mode.
>> Thu May 12 05:36:24 2016 kern.info kernel: [ 5.678440] hub 2-0:1.0: USB
>> hub found
>> Thu May 12 05:36:24 2016 kern.info kernel: [ 5.681390] hub 2-0:1.0: 1
>> port detected
>> Thu May 12 05:36:24 2016 user.info kernel: [ 5.687615] init: - preinit -
>> Thu May 12 05:36:24 2016 kern.notice kernel: [ 6.192804] random: procd
>> urandom read with 26 bits of entropy available
>> Thu May 12 05:36:24 2016 kern.notice kernel: [ 8.569614] jffs2: notice:
>> (370) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of
>> xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found.
>> Thu May 12 05:36:24 2016 user.info kernel: [ 8.585353] mount_root:
>> switching to jffs2 overlay
>> Thu May 12 05:36:24 2016 user.info kernel: [ 8.606254] procd: - early -
>> Thu May 12 05:36:24 2016 user.info kernel: [ 8.607917] procd: - watchdog
>> -
>> Thu May 12 05:36:24 2016 user.info kernel: [ 9.348938] procd: - ubus -
>> Thu May 12 05:36:24 2016 user.info kernel: [ 9.403903] procd: - init -
>> Thu May 12 05:36:24 2016 kern.info kernel: [ 10.231370] IFXOS, Version
>> 1.5.19 (c) Copyright 2009, Lantiq Deutschland GmbH
>> Thu May 12 05:36:24 2016 kern.info kernel: [ 10.241461] NET: Registered
>> protocol family 8
>> Thu May 12 05:36:24 2016 kern.info kernel: [ 10.244431] NET: Registered
>> protocol family 20
>> Thu May 12 05:36:24 2016 kern.info kernel: [ 10.255629] PPP generic driver
>> version 2.4.2
>> Thu May 12 05:36:24 2016 kern.info kernel: [ 10.266429] ip6_tables: (C)
>> 2000-2006 Netfilter Core Team
>> Thu May 12 05:36:24 2016 kern.info kernel: [ 10.291707] Lantiq (VRX) DSL
>> CPE MEI driver, version 1.4.8.5, (c) 2013 Lantiq Deutschland GmbH
>> Thu May 12 05:36:24 2016 kern.info kernel: [ 10.291707]
>> Thu May 12 05:36:24 2016 kern.info kernel: [ 10.291707] Lantiq CPE API
>> Driver version: DSL CPE API V4.16.6.3
>> Thu May 12 05:36:24 2016 kern.warn kernel: [ 10.312794]
>> Thu May 12 05:36:24 2016 kern.warn kernel: [ 10.312794] Predefined debug
>> level: 3
>> Thu May 12 05:36:24 2016 kern.info kernel: [ 10.323452] Loading modules
>> backported from Linux version v4.4-rc5-1913-gc8fdf68
>> Thu May 12 05:36:24 2016 kern.info kernel: [ 10.329464] Backport generated
>> by backports.git backports-20151218-0-g2f58d9d
>> Thu May 12 05:36:24 2016 kern.info kernel: [ 10.340031] ip_tables: (C)
>> 2000-2006 Netfilter Core Team
>> Thu May 12 05:36:24 2016 kern.info kernel: [ 10.351117] Infineon
>> Technologies DEU driver version 2.0.0
>> Thu May 12 05:36:24 2016 kern.notice kernel: [ 10.357203] IFX DEU DES
>> initialized (multiblock).
>> Thu May 12 05:36:24 2016 kern.notice kernel: [ 10.361497] IFX DEU AES
>> initialized (multiblock).
>> Thu May 12 05:36:24 2016 kern.notice kernel: [ 10.365620] IFX DEU ARC4
>> initialized (multiblock).
>> Thu May 12 05:36:24 2016 kern.notice kernel: [ 10.370239] IFX DEU SHA1
>> initialized.
>> Thu May 12 05:36:24 2016 kern.notice kernel: [ 10.373843] IFX DEU MD5
>> initialized.
>> Thu May 12 05:36:24 2016 kern.notice kernel: [ 10.377438] IFX DEU
>> SHA1_HMAC initialized.
>> Thu May 12 05:36:24 2016 kern.notice kernel: [ 10.381556] IFX DEU MD5_HMAC
>> initialized.
>> Thu May 12 05:36:24 2016 kern.info kernel: [ 10.391907] nf_conntrack
>> version 0.5.0 (1946 buckets, 7784 max)
>> Thu May 12 05:36:24 2016 kern.info kernel: [ 10.418114] NET: Registered
>> protocol family 24
>> Thu May 12 05:36:24 2016 kern.info kernel: [ 10.443723] xt_time: kernel
>> timezone is -0000
>> Thu May 12 05:36:24 2016 kern.warn kernel: [ 10.539595] PCI: Enabling
>> device 0000:01:00.0 (0140 -> 0142)
>> Thu May 12 05:36:24 2016 kern.debug kernel: [ 10.550629] ath: EEPROM
>> regdomain: 0x8114
>> Thu May 12 05:36:24 2016 kern.debug kernel: [ 10.550653] ath: EEPROM
>> indicates we should expect a country code
>> Thu May 12 05:36:24 2016 kern.debug kernel: [ 10.550667] ath: doing EEPROM
>> country->regdmn map search
>> Thu May 12 05:36:24 2016 kern.debug kernel: [ 10.550679] ath: country maps
>> to regdmn code: 0x37
>> Thu May 12 05:36:24 2016 kern.debug kernel: [ 10.550692] ath: Country
>> alpha2 being used: DE
>> Thu May 12 05:36:24 2016 kern.debug kernel: [ 10.550704] ath: Regpair
>> used: 0x37
>> Thu May 12 05:36:24 2016 kern.debug kernel: [ 10.564122] ieee80211 phy0:
>> Selected rate control algorithm 'minstrel_ht'
>> Thu May 12 05:36:24 2016 kern.info kernel: [ 10.567111] ieee80211 phy0:
>> Atheros AR9287 Rev:2 mem=0xbc000000, irq=144
>> Thu May 12 05:36:25 2016 user.notice : 'radio0' is disabled
>> Thu May 12 05:36:25 2016 user.notice : 'radio0' is disabled
>> Thu May 12 05:36:26 2016 user.notice : firmware for annex a not found
>> Thu May 12 05:36:28 2016 authpriv.info dropbear[840]: Not backgrounding
>> Thu May 12 05:36:28 2016 user.notice : setting up led wifi
>> Thu May 12 05:36:28 2016 user.notice : setting up led dsl
>> Thu May 12 05:36:28 2016 user.notice : setting up led internet
>> Thu May 12 05:36:29 2016 daemon.info procd: - init complete -
>> Thu May 12 05:36:30 2016 kern.info kernel: [ 19.477228] device eth0.1
>> entered promiscuous mode
>> Thu May 12 05:36:30 2016 kern.info kernel: [ 19.480651] device eth0
>> entered promiscuous mode
>> Thu May 12 05:36:30 2016 kern.info kernel: [ 19.500394] br-lan: port
>> 1(eth0.1) entered forwarding state
>> Thu May 12 05:36:30 2016 kern.info kernel: [ 19.504638] br-lan: port
>> 1(eth0.1) entered forwarding state
>> Thu May 12 05:36:30 2016 daemon.notice netifd: Interface 'lan' is enabled
>> Thu May 12 05:36:30 2016 daemon.notice netifd: Interface 'lan' is setting up
>> now
>> Thu May 12 05:36:30 2016 daemon.notice netifd: Interface 'lan' is now up
>> Thu May 12 05:36:30 2016 daemon.notice netifd: Interface 'loopback' is
>> enabled
>> Thu May 12 05:36:30 2016 daemon.notice netifd: Interface 'loopback' is
>> setting up now
>> Thu May 12 05:36:30 2016 daemon.notice netifd: Interface 'loopback' is now
>> up
>> Thu May 12 05:36:30 2016 daemon.notice netifd: Bridge 'br-lan' link is up
>> Thu May 12 05:36:30 2016 daemon.notice netifd: Interface 'lan' has link
>> connectivity
>> Thu May 12 05:36:30 2016 daemon.notice netifd: Network device 'eth0' link is
>> up
>> Thu May 12 05:36:30 2016 daemon.notice netifd: VLAN 'eth0.1' link is up
>> Thu May 12 05:36:30 2016 daemon.notice netifd: Network device 'lo' link is
>> up
>> Thu May 12 05:36:30 2016 daemon.notice netifd: Interface 'loopback' has link
>> connectivity
>> Thu May 12 05:36:30 2016 user.notice firewall: Reloading firewall due to
>> ifup of lan (br-lan)
>> Thu May 12 05:36:32 2016 kern.info kernel: [ 21.506873] br-lan: port
>> 1(eth0.1) entered forwarding state
>> Thu May 12 05:36:35 2016 daemon.info dnsmasq[989]: started, version 2.75
>> cachesize 150
>> Thu May 12 05:36:35 2016 daemon.info dnsmasq[989]: compile time options:
>> IPv6 GNU-getopt no-DBus no-i18n no-IDN DHCP no-DHCPv6 no-Lua TFTP
>> no-conntrack no-ipset no-auth no-DNSSEC loop-detect inotify
>> Thu May 12 05:36:35 2016 daemon.info dnsmasq[989]: DNS service limited to
>> local subnets
>> Thu May 12 05:36:35 2016 daemon.info dnsmasq-dhcp[989]: DHCP, IP range
>> 192.168.2.100 -- 192.168.2.249, lease time 12h
>> Thu May 12 05:36:35 2016 daemon.info dnsmasq[989]: using local addresses
>> only for domain lan
>> Thu May 12 05:36:35 2016 daemon.warn dnsmasq[989]: no servers found in
>> /tmp/resolv.conf.auto, will retry
>> Thu May 12 05:36:35 2016 daemon.info dnsmasq[989]: read /etc/hosts - 4
>> addresses
>> Thu May 12 05:36:35 2016 daemon.info dnsmasq[989]: read /tmp/hosts/dhcp - 2
>> addresses
>> Thu May 12 05:36:35 2016 daemon.info dnsmasq-dhcp[989]: read /etc/ethers - 0
>> addresses
>> Thu May 12 05:36:42 2016 kern.notice kernel: [ 31.802908] random:
>> nonblocking pool is initialized
>>
>>
>> _______________________________________________
>> openwrt-devel mailing list
>> openwrt-devel at lists.openwrt.org
>> https://lists.openwrt.org/cgi-bin/mailman/listinfo/openwrt-devel
>>
-------------- next part --------------
A non-text attachment was scrubbed...
Name: 7360.diff
Type: text/x-patch
Size: 6970 bytes
Desc: not available
URL: <http://lists.infradead.org/pipermail/openwrt-devel/attachments/20160515/61f3464f/attachment.bin>
-------------- next part --------------
_______________________________________________
openwrt-devel mailing list
openwrt-devel at lists.openwrt.org
https://lists.openwrt.org/cgi-bin/mailman/listinfo/openwrt-devel
More information about the openwrt-devel
mailing list