[OpenWrt-Devel] ar71xx with kernel 4.4 on WZR-HP-AG300H
Andre Valentin
avalentin at marcant.net
Sat Jan 30 18:46:09 EST 2016
Hi!
I've got some problems with new 4.4 kernel on ar711 with my WZR-HP-AG300H. Please just take this as a notice, I know it's testing ;-)
If you need more testing, I'm available.
André
Here's the log:
console=ttyS0,115200 root=31:03 rootfstype=jffs2 init=/sbin/init
mtdparts=ar7100-nor0:256k(u-boot),64k(u-boot-env),1152k at 384k(uImage),6592k at 1536k(rootfs),64k at 320k(ART),64k at 8128k(properties),8192k at 8192k(flash1),M
## Booting image at bf060000 ...
Image Name: MIPS OpenWrt Linux-4.4
Created: 2016-01-30 21:45:43 UTC
Image Type: MIPS Linux Kernel Image (lzma compressed)
Data Size: 1402157 Bytes = 1.3 MB
Load Address: 80060000
Entry Point: 80060000
Verifying Checksum ... crc32_fw: bf060040 - bf1b656c (len:0015652d) calc...
crc32_fw: range1 bf060040 - bf1b656c
OK
Uncompressing Kernel Image ... OK
No initrd
## Transferring control to Linux (at address 80060000) ...
## Giving linux memsize in bytes, 134217728
Starting kernel ...
[ 0.000000] Linux version 4.4.0 (avalentin at nixdevel.ad.ddimension.net) (gcc version 5.2.0 (OpenWrt GCC 5.2.0 r48531) ) #1 Sat Jan 30 21:45:32 UTC 2016
[ 0.000000] bootconsole [early0] enabled
[ 0.000000] CPU0 revision is: 00019374 (MIPS 24Kc)
[ 0.000000] SoC: Atheros AR7161 rev 2
[ 0.000000] Determined physical RAM map:
[ 0.000000] memory: 08000000 @ 00000000 (usable)
[ 0.000000] Initrd not found or empty - disabling initrd
[ 0.000000] No valid device tree found, continuing without
[ 0.000000] Zone ranges:
[ 0.000000] Normal [mem 0x0000000000000000-0x0000000007ffffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x0000000000000000-0x0000000007ffffff]
[ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000007ffffff]
[ 0.000000] Reserving 0MB of memory at 0MB for crashkernel
[ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
[ 0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 32512
[ 0.000000] Kernel command line: board=WZR-HP-AG300H console=ttyS0,115200 rootfstype=squashfs,jffs2 noinitrd
[ 0.000000] PID hash table entries: 512 (order: -1, 2048 bytes)
[ 0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
[ 0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.000000] Writing ErrCtl register=00000000
[ 0.000000] Readback ErrCtl register=00000000
[ 0.000000] Memory: 125064K/131072K available (3127K kernel code, 156K rwdata, 648K rodata, 284K init, 213K bss, 6008K reserved, 0K cma-reserved)
[ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.000000] NR_IRQS:51
[ 0.000000] Clocks: CPU:680.000MHz, DDR:340.000MHz, AHB:170.000MHz, Ref:40.000MHz
[ 0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 5621354254 ns
[ 0.000008] sched_clock: 32 bits at 340MHz, resolution 2ns, wraps every 6316128254ns
[ 0.007737] Calibrating delay loop... 452.19 BogoMIPS (lpj=2260992)
[ 0.070375] pid_max: default: 32768 minimum: 301
[ 0.075074] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.081595] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.089325] Initializing cgroup subsys io
[ 0.093284] Initializing cgroup subsys devices
[ 0.097666] Initializing cgroup subsys freezer
[ 0.102081] Initializing cgroup subsys net_cls
[ 0.106505] Initializing cgroup subsys pids
[ 0.111981] devtmpfs: initialized
[ 0.115925] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[ 0.126352] NET: Registered protocol family 16
[ 0.131647] MIPS: machine is Buffalo WZR-HP-AG300H/WZR-600DHP
[ 2.777559] registering PCI controller with io_map_base unset
[ 2.790904] PCI host bridge to bus 0000:00
[ 2.794968] pci_bus 0000:00: root bus resource [mem 0x10000000-0x16ffffff]
[ 2.801754] pci_bus 0000:00: root bus resource [io 0x0000]
[ 2.807306] pci_bus 0000:00: root bus resource [??? 0x00000000 flags 0x0]
[ 2.814050] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
[ 2.822006] pci 0000:00:11.0: fixup device configuration
[ 2.828688] pci 0000:00:12.0: fixup device configuration
[ 2.835385] pci 0000:00:11.0: BAR 0: assigned [mem 0x10000000-0x1000ffff]
[ 2.842075] pci 0000:00:12.0: BAR 0: assigned [mem 0x10010000-0x1001ffff]
[ 2.848856] pci 0000:00:11.0: using irq 40 for pin 1
[ 2.853756] pci 0000:00:12.0: using irq 41 for pin 1
[ 2.859447] clocksource: Switched to clocksource MIPS
[ 2.868345] NET: Registered protocol family 2
[ 2.873464] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
[ 2.880397] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
[ 2.886667] TCP: Hash tables configured (established 1024 bind 1024)
[ 2.893083] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 2.898830] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 2.905314] NET: Registered protocol family 1
[ 2.910501] futex hash table entries: 256 (order: -1, 3072 bytes)
[ 2.929097] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 2.934901] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 2.946965] io scheduler noop registered
[ 2.950859] io scheduler deadline registered (default)
[ 2.956647] Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled
�[ 2.987465] serial8250.0: ttyS0 at MMIO 0x18020000 (irq = 11, base_baud = 10625000) is a 16550A
[ 2.996083] console [ttyS0] enabled
[ 2.996083] console [ttyS0] enabled
[ 3.002999] bootconsole [early0] disabled
[ 3.002999] bootconsole [early0] disabled
[ 3.013458] m25p80 spi0.0: found w25q128, expected m25p80
[ 3.018861] m25p80 spi0.0: w25q128 (16384 Kbytes)
[ 3.026299] m25p80 spi0.1: found w25q128, expected m25p80
[ 3.031754] m25p80 spi0.1: w25q128 (16384 Kbytes)
[ 3.040647] Concatenating MTD devices:
[ 3.044398] (0): "spi0.0"
[ 3.047011] (1): "spi0.1"
[ 3.049659] into device "flash"
[ 3.052803] Creating 5 MTD partitions on "flash":
[ 3.057503] 0x000000000000-0x000000040000 : "u-boot"
[ 3.065576] switch0: Atheros AR8316 rev. 1 switch registered on ag71xx-mdio.0
[ 3.075753] libphy: ag71xx_mdio: probed
[ 3.081369] 0x000000040000-0x000000050000 : "u-boot-env"
[ 3.088439] 0x000000050000-0x000000060000 : "art"
[ 3.094991] 0x000000060000-0x000001ff0000 : "firmware"
[ 3.190189] 2 uimage-fw partitions found on MTD device firmware
[ 3.196110] 0x000000060000-0x0000001b656d : "kernel"
[ 3.202566] 0x0000001b656d-0x000001ff0000 : "rootfs"
[ 3.209293] mtd: device 7 (rootfs) set to be root filesystem
[ 3.215057] 1 squashfs-split partitions found on MTD device rootfs
[ 3.221242] 0x000001790000-0x000001ff0000 : "rootfs_data"
[ 3.228451] 0x000001ff0000-0x000002000000 : "user_property"
[ 3.400821] ar8316: Using port 4 as switch port
[ 3.435260] ag71xx ag71xx.0: connected to PHY at ag71xx-mdio.0:00 [uid=004dd041, driver=Atheros AR8216/AR8236/AR8316]
[ 3.446435] eth0: Atheros AG71xx at 0xb9000000, irq 4, mode:RGMII
[ 3.770815] ar8316: Using port 4 as PHY
[ 4.811571] ag71xx ag71xx.1: connected to PHY at ag71xx-mdio.0:04 [uid=004dd041, driver=Atheros AR8216/AR8236/AR8316]
[ 4.822769] eth1: Atheros AG71xx at 0xba000000, irq 5, mode:RGMII
[ 4.830997] NET: Registered protocol family 10
[ 4.838214] NET: Registered protocol family 17
[ 4.842782] bridge: automatic filtering via arp/ip/ip6tables has been deprecated. Update your scripts to load br_netfilter if you need this.
[ 4.855482] 8021q: 802.1Q VLAN Support v1.8
[ 4.870396] VFS: Mounted root (squashfs filesystem) readonly on device 31:7.
[ 4.878306] Freeing unused kernel memory: 284K (80439000 - 80480000)
[ 6.978793] init: Console is alive
[ 6.982604] init: - watchdog -
[ 9.237529] usbcore: registered new interface driver usbfs
[ 9.243152] usbcore: registered new interface driver hub
[ 9.248523] usbcore: registered new device driver usb
[ 9.257859] Button Hotplug driver version 0.4.1
[ 9.271478] SCSI subsystem initialized
[ 9.280491] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 9.288373] ehci-platform: EHCI generic platform driver
[ 9.293719] ehci-platform ehci-platform: EHCI Host Controller
[ 9.299503] ehci-platform ehci-platform: new USB bus registered, assigned bus number 1
[ 9.307516] ehci-platform ehci-platform: irq 3, io mem 0x1b000000
[ 9.329539] ehci-platform ehci-platform: USB 2.0 started, EHCI 1.00
[ 9.336696] hub 1-0:1.0: USB hub found
[ 9.340792] hub 1-0:1.0: 2 ports detected
[ 9.346481] ehci-pci: EHCI PCI platform driver
[ 9.355173] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 9.362655] ohci-platform: OHCI generic platform driver
[ 9.367951] ohci-platform ohci-platform: Generic Platform OHCI controller
[ 9.374810] ohci-platform ohci-platform: new USB bus registered, assigned bus number 2
[ 9.382804] ohci-platform ohci-platform: irq 14, io mem 0x1c000000
[ 9.444395] hub 2-0:1.0: USB hub found
[ 9.448427] hub 2-0:1.0: 2 ports detected
[ 9.454823] uhci_hcd: USB Universal Host Controller Interface driver
[ 9.473894] usbcore: registered new interface driver usb-storage
[ 9.481150] Error: Driver 'gpio-keys-polled' is already registered, aborting...
4[ 10.043002] init: - preinit -
[ 10.639997] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 10.818917] random: procd urandom read with 17 bits of entropy available
Press the [f] key and hit [enter] to enter failsafe mode
Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level
[ 11.073781] mount_root: loading kmods from internal overlay
[ 11.133098] Error: Driver 'gpio-keys-polled' is already registered, aborting...
[ 11.141826] kmodloader: 1 module could not be probed
[ 11.147023] kmodloader: - gpio_keys_polled - 0
[ 12.258521] jffs2_scan_eraseblock(): End of filesystem marker found at 0x60000
[ 12.265787] jffs2_build_filesystem(): unlocking the mtd device... done.
[ 12.272407] jffs2_build_filesystem(): erasing all blocks after the end marker...
[ 12.670044] eth0: link up (1000Mbps/Full duplex)
[ 12.674697] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
BUFFALO U-BOOT Ver 1.01
== CPU:680MHz, DDR:340MHz, AHB:170MHz ==
AP96 (ar7100) U-boot 0.0.1
DRAM: 128 MB
_______________________________________________
openwrt-devel mailing list
openwrt-devel at lists.openwrt.org
https://lists.openwrt.org/cgi-bin/mailman/listinfo/openwrt-devel
More information about the openwrt-devel
mailing list