[OpenWrt-Devel] [PATCH] Add support for Netgear D7800
John Crispin
blogic at openwrt.org
Tue Jan 19 03:36:30 EST 2016
you patch collides with f177c2c2f956c938045bd53943e3f1c090b5db2b so you
will have to rebase/send it.
On 19/01/2016 09:26, Tathagata Das wrote:
> Hi John,
>
> I sent the patch last time using git command and I even received an email
> from OpenWRT on 12th January 2016.
>
> Regards,
> Tathagata
>
>
> -----Original Message-----
> From: John Crispin [mailto:blogic at openwrt.org]
> Sent: 19 January 2016 13:45
> To: Tathagata Das; openwrt-devel at lists.openwrt.org
> Subject: Re: [OpenWrt-Devel] [PATCH] Add support for Netgear D7800
>
> same as before, we are waiting on you to send a version that applies.
>
>
> patchwork 566597
> --2016-01-17 06:23:22-- http://patchwork.ozlabs.org/patch/566597/mbox/
> Resolving patchwork.ozlabs.org (patchwork.ozlabs.org)... 103.22.144.67
> Connecting to patchwork.ozlabs.org
> (patchwork.ozlabs.org)|103.22.144.67|:80... connected.
> HTTP request sent, awaiting response... 200 OK
> Length: unspecified [text/plain]
> Saving to: `566597.patch'
>
> [ <=>
> ] 12,864 --.-K/s in 0s
>
> 2016-01-17 06:23:24 (115 MB/s) - `566597.patch' saved [12864]
>
> Applying: Add support for Netgear D7800
> Using index info to reconstruct a base tree...
> <stdin>:109: space before tab in indent.
> qcom-ipq8064-ap148.dtb \
> <stdin>:110: space before tab in indent.
> qcom-ipq8064-db149.dtb \
> <stdin>:111: space before tab in indent.
> qcom-ipq8064-r7500.dtb \
> <stdin>:113: space before tab in indent.
> qcom-msm8660-surf.dtb \
> <stdin>:114: space before tab in indent.
> qcom-msm8960-cdp.dtb \
> warning: squelched 1 whitespace error
> warning: 6 lines add whitespace errors.
> Falling back to patching base and 3-way merge...
> Auto-merging target/linux/ipq806x/image/Makefile
> Auto-merging target/linux/ipq806x/base-files/lib/upgrade/platform.sh
> CONFLICT (content): Merge conflict in
> target/linux/ipq806x/base-files/lib/upgrade/platform.sh
> Failed to merge in the changes.
> Patch failed at 0001 Add support for Netgear D7800 When you have resolved
> this problem run "git am --resolved".
> If you would prefer to skip this patch, instead run "git am --skip".
> To restore the original branch and stop patching run "git am --abort".
> Unstaged changes after reset:
> M target/linux/ipq806x/base-files/etc/board.d/01_leds
> M target/linux/ipq806x/base-files/etc/board.d/02_network
> M target/linux/ipq806x/base-files/lib/ipq806x.sh
> M target/linux/ipq806x/base-files/lib/upgrade/platform.sh
> M target/linux/ipq806x/image/Makefile
> M target/linux/ipq806x/profiles/netgear.mk
> applying 566597 FAILED
>
>
> patchwork 569813
> --2016-01-17 06:22:13-- http://patchwork.ozlabs.org/patch/569813/mbox/
> Resolving patchwork.ozlabs.org (patchwork.ozlabs.org)... 103.22.144.67
> Connecting to patchwork.ozlabs.org
> (patchwork.ozlabs.org)|103.22.144.67|:80... connected.
> HTTP request sent, awaiting response... 200 OK
> Length: unspecified [text/plain]
> Saving to: `569813.patch'
>
> [ <=>
> ] 13,088 --.-K/s in 0s
>
> 2016-01-17 06:22:14 (172 MB/s) - `569813.patch' saved [13088]
>
> Applying: Add support for Netgear D7800
> fatal: patch fragment without header at line 130: @@ -0,0 +1,381 @@
> Repository lacks necessary blobs to fall back on 3-way merge.
> Cannot fall back to three-way merge.
> Patch failed at 0001 Add support for Netgear D7800 When you have resolved
> this problem run "git am --resolved".
> If you would prefer to skip this patch, instead run "git am --skip".
> To restore the original branch and stop patching run "git am --abort".
> applying 569813 FAILED
>
>
>
>
> On 19/01/2016 07:19, Tathagata Das wrote:
>> Any update about the patch?
>>
>> Regards,
>> Tathagata
>>
>>
>> -----Original Message-----
>> From: Tathagata Das [mailto:tathagata at alumnux.com]
>> Sent: 12 January 2016 20:47
>> To: openwrt-devel at lists.openwrt.org
>> Cc: Tathagata Das
>> Subject: [PATCH] Add support for Netgear D7800
>>
>> Signed-off-by: Tathagata Das <tathagata at alumnux.com>
>> ---
>> .../linux/ipq806x/base-files/etc/board.d/01_leds | 1 +
>> .../ipq806x/base-files/etc/board.d/02_network | 1 +
>> target/linux/ipq806x/base-files/lib/ipq806x.sh | 3 +
>> .../ipq806x/base-files/lib/upgrade/platform.sh | 2 +
>> target/linux/ipq806x/image/Makefile | 13 +-
>> ...dd-Netgear-Nighthawk-X4-D7800-device-tree.patch | 381
>> +++++++++++++++++++++
>> target/linux/ipq806x/profiles/netgear.mk | 13 +
>> 7 files changed, 413 insertions(+), 1 deletion(-) create mode 100644
>> target/linux/ipq806x/patches-3.18/801-ARM-qcom-add-Netgear-Nighthawk-X
>> 4-D780
>> 0-device-tree.patch
>>
>> diff --git a/target/linux/ipq806x/base-files/etc/board.d/01_leds
>> b/target/linux/ipq806x/base-files/etc/board.d/01_leds
>> index 07b5b06..b32c1cc 100755
>> --- a/target/linux/ipq806x/base-files/etc/board.d/01_leds
>> +++ b/target/linux/ipq806x/base-files/etc/board.d/01_leds
>> @@ -11,6 +11,7 @@ board_config_update
>> board=$(ipq806x_board_name)
>>
>> case "$board" in
>> +d7800 |\
>> r7500)
>> ucidef_set_led_usbdev "usb1" "USB 1" "r7500:white:usb1" "1-1"
>> ucidef_set_led_usbdev "usb2" "USB 2" "r7500:white:usb3" "3-1"
>> diff --git a/target/linux/ipq806x/base-files/etc/board.d/02_network
>> b/target/linux/ipq806x/base-files/etc/board.d/02_network
>> index 1302a55..6e18297 100755
>> --- a/target/linux/ipq806x/base-files/etc/board.d/02_network
>> +++ b/target/linux/ipq806x/base-files/etc/board.d/02_network
>> @@ -13,6 +13,7 @@ board=$(ipq806x_board_name)
>>
>> case "$board" in
>> ap148 |\
>> +d7800 |\
>> r7500)
>> ucidef_add_switch "switch0" \
>> "1:lan" "2:lan" "3:lan" "4:lan" "6 at eth1" "5:wan" "0 at eth0"
>> diff --git a/target/linux/ipq806x/base-files/lib/ipq806x.sh
>> b/target/linux/ipq806x/base-files/lib/ipq806x.sh
>> index 5b27bde..db22708 100644
>> --- a/target/linux/ipq806x/base-files/lib/ipq806x.sh
>> +++ b/target/linux/ipq806x/base-files/lib/ipq806x.sh
>> @@ -17,6 +17,9 @@ ipq806x_board_detect() {
>> *"AP148")
>> name="ap148"
>> ;;
>> + *"D7800")
>> + name="d7800"
>> + ;;
>> *"DB149")
>> name="db149"
>> ;;
>> diff --git a/target/linux/ipq806x/base-files/lib/upgrade/platform.sh
>> b/target/linux/ipq806x/base-files/lib/upgrade/platform.sh
>> index c0e19a1..2400376 100644
>> --- a/target/linux/ipq806x/base-files/lib/upgrade/platform.sh
>> +++ b/target/linux/ipq806x/base-files/lib/upgrade/platform.sh
>> @@ -7,6 +7,7 @@ platform_check_image() {
>>
>> case "$board" in
>> AP148 |\
>> + d7800 |\
>> r7500)
>> nand_do_platform_check $board $1
>> return $?;
>> @@ -21,6 +22,7 @@ platform_pre_upgrade() {
>>
>> case "$board" in
>> AP148 |\
>> + d7800 |\
>> r7500)
>> nand_do_upgrade "$1"
>> ;;
>> diff --git a/target/linux/ipq806x/image/Makefile
>> b/target/linux/ipq806x/image/Makefile
>> index 14cf442..b880a1b 100644
>> --- a/target/linux/ipq806x/image/Makefile
>> +++ b/target/linux/ipq806x/image/Makefile
>> @@ -103,6 +103,17 @@ define Device/AP148-legacy
>> BOARD_NAME := ap148
>> endef
>>
>> +define Device/D7800
>> + $(call Device/DniImage)
>> + DEVICE_DTS := qcom-ipq8064-d7800
>> + KERNEL_SIZE := 2097152
>> + NETGEAR_BOARD_ID := D7800
>> + NETGEAR_HW_ID := 29764958+0+128+512+4x4+4x4
>> + BLOCKSIZE := 128KiB
>> + PAGESIZE := 2048
>> + BOARD_NAME := d7800
>> +endef
>> +
>> define Device/DB149
>> $(call Device/FitImage)
>> DEVICE_DTS := qcom-ipq8064-db149
>> @@ -121,6 +132,6 @@ define Device/R7500
>> BOARD_NAME := r7500
>> endef
>>
>> -TARGET_DEVICES += AP148 AP148-legacy DB149 R7500
>> +TARGET_DEVICES += AP148 AP148-legacy D7800 DB149 R7500
>>
>> $(eval $(call BuildImage))
>> diff --git
>> a/target/linux/ipq806x/patches-3.18/801-ARM-qcom-add-Netgear-Nighthawk
>> -X4-D7
>> 800-device-tree.patch
>> b/target/linux/ipq806x/patches-3.18/801-ARM-qcom-add-Netgear-Nighthawk
>> -X4-D7
>> 800-device-tree.patch
>> new file mode 100644
>> index 0000000..ecc1cff
>> --- /dev/null
>> +++ b/target/linux/ipq806x/patches-3.18/801-ARM-qcom-add-Netgear-Night
>> +++ ha
>> +++ wk-X4-D7800-device-tree.patch
>> @@ -0,0 +1,381 @@
>> +--- a/arch/arm/boot/dts/Makefile 2015-09-22 18:30:09.033530282 +0530
>> ++++ b/arch/arm/boot/dts/Makefile 2015-09-23 17:06:44.892947581 +0530
>> +@@ -362,6 +362,7 @@
>> + qcom-ipq8064-ap148.dtb \
>> + qcom-ipq8064-db149.dtb \
>> + qcom-ipq8064-r7500.dtb \
>> ++ qcom-ipq8064-d7800.dtb \
>> + qcom-msm8660-surf.dtb \
>> + qcom-msm8960-cdp.dtb \
>> + qcom-msm8974-sony-xperia-honami.dtb
>> +--- a/arch/arm/boot/dts/qcom-ipq8064-d7800.dts 1970-01-01
>> 05:30:00.000000000 +0530
>> ++++ b/arch/arm/boot/dts/qcom-ipq8064-d7800.dts 2015-09-23
>> 17:06:45.336947567 +0530
>> +@@ -0,0 +1,368 @@
>> ++#include "qcom-ipq8064-v1.0.dtsi"
>> ++
>> ++#include <dt-bindings/input/input.h>
>> ++
>> ++/ {
>> ++ model = "Netgear Nighthawk X4 D7800";
>> ++ compatible = "netgear,d7800", "qcom,ipq8064";
>> ++
>> ++ memory at 0 {
>> ++ reg = <0x42000000 0xe000000>;
>> ++ device_type = "memory";
>> ++ };
>> ++
>> ++ reserved-memory {
>> ++ #address-cells = <1>;
>> ++ #size-cells = <1>;
>> ++ ranges;
>> ++ rsvd at 41200000 {
>> ++ reg = <0x41200000 0x300000>;
>> ++ no-map;
>> ++ };
>> ++ };
>> ++
>> ++ aliases {
>> ++ serial0 = &uart4;
>> ++ mdio-gpio0 = &mdio0;
>> ++ };
>> ++
>> ++ chosen {
>> ++ bootargs = "rootfstype=squashfs noinitrd";
>> ++ linux,stdout-path = "serial0:115200n8";
>> ++ };
>> ++
>> ++ soc {
>> ++ pinmux at 800000 {
>> ++ i2c4_pins: i2c4_pinmux {
>> ++ pins = "gpio12", "gpio13";
>> ++ function = "gsbi4";
>> ++ bias-disable;
>> ++ };
>> ++
>> ++ pcie0_pins: pcie0_pinmux {
>> ++ mux {
>> ++ pins = "gpio3";
>> ++ function = "pcie1_rst";
>> ++ drive-strength = <12>;
>> ++ bias-disable;
>> ++ };
>> ++ };
>> ++
>> ++ pcie1_pins: pcie1_pinmux {
>> ++ mux {
>> ++ pins = "gpio48";
>> ++ function = "pcie2_rst";
>> ++ drive-strength = <12>;
>> ++ bias-disable;
>> ++ };
>> ++ };
>> ++
>> ++ nand_pins: nand_pins {
>> ++ mux {
>> ++ pins = "gpio34", "gpio35", "gpio36",
>> ++ "gpio37", "gpio38", "gpio39",
>> ++ "gpio40", "gpio41", "gpio42",
>> ++ "gpio43", "gpio44", "gpio45",
>> ++ "gpio46", "gpio47";
>> ++ function = "nand";
>> ++ drive-strength = <10>;
>> ++ bias-disable;
>> ++ };
>> ++ pullups {
>> ++ pins = "gpio39";
>> ++ bias-pull-up;
>> ++ };
>> ++ hold {
>> ++ pins = "gpio40", "gpio41", "gpio42",
>> ++ "gpio43", "gpio44", "gpio45",
>> ++ "gpio46", "gpio47";
>> ++ bias-bus-hold;
>> ++ };
>> ++ };
>> ++
>> ++ mdio0_pins: mdio0_pins {
>> ++ mux {
>> ++ pins = "gpio0", "gpio1";
>> ++ function = "gpio";
>> ++ drive-strength = <8>;
>> ++ bias-disable;
>> ++ };
>> ++ };
>> ++
>> ++ rgmii2_pins: rgmii2_pins {
>> ++ mux {
>> ++ pins = "gpio27", "gpio28", "gpio29",
>> "gpio30", "gpio31", "gpio32",
>> ++ "gpio51", "gpio52", "gpio59",
>> "gpio60", "gpio61", "gpio62" ;
>> ++ function = "rgmii2";
>> ++ drive-strength = <8>;
>> ++ bias-disable;
>> ++ };
>> ++ };
>> ++ };
>> ++
>> ++ gsbi at 16300000 {
>> ++ qcom,mode = <GSBI_PROT_I2C_UART>;
>> ++ status = "ok";
>> ++ serial at 16340000 {
>> ++ status = "ok";
>> ++ };
>> ++ /*
>> ++ * The i2c device on gsbi4 should not be enabled.
>> ++ * On ipq806x designs gsbi4 i2c is meant for
>> exclusive
>> ++ * RPM usage. Turning this on in kernel manifests as
>> ++ * i2c failure for the RPM.
>> ++ */
>> ++ };
>> ++
>> ++ sata-phy at 1b400000 {
>> ++ status = "ok";
>> ++ };
>> ++
>> ++ sata at 29000000 {
>> ++ status = "ok";
>> ++ };
>> ++
>> ++ phy at 100f8800 { /* USB3 port 1 HS phy */
>> ++ status = "ok";
>> ++ };
>> ++
>> ++ phy at 100f8830 { /* USB3 port 1 SS phy */
>> ++ status = "ok";
>> ++ };
>> ++
>> ++ phy at 110f8800 { /* USB3 port 0 HS phy */
>> ++ status = "ok";
>> ++ };
>> ++
>> ++ phy at 110f8830 { /* USB3 port 0 SS phy */
>> ++ status = "ok";
>> ++ };
>> ++
>> ++ usb30 at 0 {
>> ++ status = "ok";
>> ++ };
>> ++
>> ++ usb30 at 1 {
>> ++ status = "ok";
>> ++ };
>> ++
>> ++ pcie0: pci at 1b500000 {
>> ++ status = "ok";
>> ++ reset-gpio = <&qcom_pinmux 3 0>;
>> ++ pinctrl-0 = <&pcie0_pins>;
>> ++ pinctrl-names = "default";
>> ++ };
>> ++
>> ++ pcie1: pci at 1b700000 {
>> ++ status = "ok";
>> ++ reset-gpio = <&qcom_pinmux 48 0>;
>> ++ pinctrl-0 = <&pcie1_pins>;
>> ++ pinctrl-names = "default";
>> ++ };
>> ++
>> ++ nand at 1ac00000 {
>> ++ status = "ok";
>> ++
>> ++ pinctrl-0 = <&nand_pins>;
>> ++ pinctrl-names = "default";
>> ++
>> ++ nand-ecc-strength = <4>;
>> ++ nand-bus-width = <8>;
>> ++
>> ++ #address-cells = <1>;
>> ++ #size-cells = <1>;
>> ++
>> ++ qcadata at 0 {
>> ++ label = "qcadata";
>> ++ reg = <0x0000000 0x0c80000>;
>> ++ read-only;
>> ++ };
>> ++
>> ++ APPSBL at c80000 {
>> ++ label = "APPSBL";
>> ++ reg = <0x0c80000 0x0500000>;
>> ++ read-only;
>> ++ };
>> ++
>> ++ APPSBLENV at 1180000 {
>> ++ label = "APPSBLENV";
>> ++ reg = <0x1180000 0x0080000>;
>> ++ read-only;
>> ++ };
>> ++
>> ++ art: art at 1200000 {
>> ++ label = "art";
>> ++ reg = <0x1200000 0x0140000>;
>> ++ read-only;
>> ++ };
>> ++
>> ++ artbak: art at 1340000 {
>> ++ label = "artbak";
>> ++ reg = <0x1340000 0x0140000>;
>> ++ read-only;
>> ++ };
>> ++
>> ++ kernel at 1480000 {
>> ++ label = "kernel";
>> ++ reg = <0x1480000 0x0200000>;
>> ++ };
>> ++
>> ++ ubi at 1680000 {
>> ++ label = "ubi";
>> ++ reg = <0x1680000 0x1E00000>;
>> ++ };
>> ++
>> ++ netgear at 3480000 {
>> ++ label = "netgear";
>> ++ reg = <0x3480000 0x4480000>;
>> ++ read-only;
>> ++ };
>> ++
>> ++ reserve at 7900000 {
>> ++ label = "reserve";
>> ++ reg = <0x7900000 0x0700000>;
>> ++ read-only;
>> ++ };
>> ++
>> ++ firmware at 1480000 {
>> ++ label = "firmware";
>> ++ reg = <0x1480000 0x2000000>;
>> ++ };
>> ++
>> ++ };
>> ++
>> ++ mdio0: mdio {
>> ++ compatible = "virtual,mdio-gpio";
>> ++ #address-cells = <1>;
>> ++ #size-cells = <0>;
>> ++ gpios = <&qcom_pinmux 1 0 &qcom_pinmux 0 0>;
>> ++ pinctrl-0 = <&mdio0_pins>;
>> ++ pinctrl-names = "default";
>> ++
>> ++ phy0: ethernet-phy at 0 {
>> ++ device_type = "ethernet-phy";
>> ++ reg = <0>;
>> ++ qca,ar8327-initvals = <
>> ++ 0x00004 0x7600000 /* PAD0_MODE */
>> ++ 0x00008 0x1000000 /* PAD5_MODE */
>> ++ 0x0000c 0x80 /* PAD6_MODE */
>> ++ 0x000e4 0xaa545 /* MAC_POWER_SEL
>> */
>> ++ 0x000e0 0xc74164de /* SGMII_CTRL */
>> ++ 0x0007c 0x4e /* PORT0_STATUS
>> */
>> ++ 0x00094 0x4e /* PORT6_STATUS
>> */
>> ++ >;
>> ++ };
>> ++
>> ++ phy4: ethernet-phy at 4 {
>> ++ device_type = "ethernet-phy";
>> ++ reg = <4>;
>> ++ };
>> ++ };
>> ++
>> ++ gmac1: ethernet at 37200000 {
>> ++ status = "ok";
>> ++ phy-mode = "rgmii";
>> ++ phy-handle = <&phy4>;
>> ++ qcom,id = <1>;
>> ++
>> ++ pinctrl-0 = <&rgmii2_pins>;
>> ++ pinctrl-names = "default";
>> ++
>> ++ mtd-mac-address = <&art 6>;
>> ++ };
>> ++
>> ++ gmac2: ethernet at 37400000 {
>> ++ status = "ok";
>> ++ phy-mode = "sgmii";
>> ++ qcom,id = <2>;
>> ++
>> ++ mtd-mac-address = <&art 0>;
>> ++
>> ++ fixed-link {
>> ++ speed = <1000>;
>> ++ full-duplex;
>> ++ };
>> ++ };
>> ++ };
>> ++
>> ++ gpio-keys {
>> ++ compatible = "gpio-keys";
>> ++
>> ++ wifi {
>> ++ label = "wifi";
>> ++ gpios = <&qcom_pinmux 6 1>;
>> ++ linux,code = <KEY_WLAN>;
>> ++ };
>> ++
>> ++ reset {
>> ++ label = "reset";
>> ++ gpios = <&qcom_pinmux 54 1>;
>> ++ linux,code = <KEY_RESTART>;
>> ++ };
>> ++
>> ++ wps {
>> ++ label = "wps";
>> ++ gpios = <&qcom_pinmux 65 1>;
>> ++ linux,code = <KEY_WPS_BUTTON>;
>> ++ };
>> ++ };
>> ++
>> ++ gpio-leds {
>> ++ compatible = "gpio-leds";
>> ++
>> ++ usb1 {
>> ++ label = "d7800:amber:usb1";
>> ++ gpios = <&qcom_pinmux 7 0>;
>> ++ };
>> ++
>> ++ usb3 {
>> ++ label = "d7800:amber:usb3";
>> ++ gpios = <&qcom_pinmux 8 0>;
>> ++ };
>> ++
>> ++ status {
>> ++ label = "d7800:amber:status";
>> ++ gpios = <&qcom_pinmux 9 0>;
>> ++ };
>> ++
>> ++ internet {
>> ++ label = "d7800:white:internet";
>> ++ gpios = <&qcom_pinmux 22 0>;
>> ++ };
>> ++
>> ++ wan {
>> ++ label = "d7800:white:wan";
>> ++ gpios = <&qcom_pinmux 23 0>;
>> ++ };
>> ++
>> ++ wps {
>> ++ label = "d7800:white:wps";
>> ++ gpios = <&qcom_pinmux 24 0>;
>> ++ };
>> ++
>> ++ esata {
>> ++ label = "d7800:white:esata";
>> ++ gpios = <&qcom_pinmux 26 0>;
>> ++ };
>> ++
>> ++ power {
>> ++ label = "d7800:white:power";
>> ++ gpios = <&qcom_pinmux 53 0>;
>> ++ default-state = "on";
>> ++ };
>> ++
>> ++ rfkill {
>> ++ label = "d7800:white:rfkill";
>> ++ gpios = <&qcom_pinmux 64 0>;
>> ++ };
>> ++
>> ++ wifi5g {
>> ++ label = "d7800:white:wifi5g";
>> ++ gpios = <&qcom_pinmux 67 0>;
>> ++ };
>> ++ };
>> ++};
>> ++
>> ++&adm_dma {
>> ++ status = "ok";
>> ++};
>> diff --git a/target/linux/ipq806x/profiles/netgear.mk
>> b/target/linux/ipq806x/profiles/netgear.mk
>> index 3402f45..25258cd 100644
>> --- a/target/linux/ipq806x/profiles/netgear.mk
>> +++ b/target/linux/ipq806x/profiles/netgear.mk
>> @@ -6,6 +6,18 @@
>> # See /LICENSE for more information.
>> #
>>
>> +define Profile/D7800
>> + NAME:=Netgear Nighthawk X4 D7800
>> + PACKAGES:= \
>> + kmod-usb-core kmod-usb-ohci kmod-usb2 kmod-ledtrig-usbdev \
>> + kmod-usb3 kmod-usb-dwc3-qcom kmod-usb-phy-qcom-dwc3 \
>> + kmod-ath10k wpad-mini ath10k-firmware-qca99x0 endef
>> +
>> +define Profile/D7800/Description
>> + Package set for the Netgear Nighthawk X4 D7800.
>> +endef
>> +
>> define Profile/R7500
>> NAME:=Netgear Nighthawk X4 R7500
>> PACKAGES:= \
>> @@ -17,4 +29,5 @@ endef
>> define Profile/R7500/Description
>> Package set for the Netgear Nighthawk X4 R7500.
>> endef
>> +$(eval $(call Profile,D7800))
>> $(eval $(call Profile,R7500))
>> --
>> 1.9.1
>> _______________________________________________
>> openwrt-devel mailing list
>> openwrt-devel at lists.openwrt.org
>> https://lists.openwrt.org/cgi-bin/mailman/listinfo/openwrt-devel
>>
_______________________________________________
openwrt-devel mailing list
openwrt-devel at lists.openwrt.org
https://lists.openwrt.org/cgi-bin/mailman/listinfo/openwrt-devel
More information about the openwrt-devel
mailing list