[OpenWrt-Devel] [PATCH v4] ramips: Add support for Netgear EX2700
Joseph C. Lehner
joseph.c.lehner at gmail.com
Tue Feb 16 10:00:08 EST 2016
I've received a notification from patchwork that the patch status has
been changed to "Accepted" 9 days ago, but it hasn't been merged yet.
Since I have another patch depending on v4, should I submit v5, or wait
until v4 has been merged and then submit a new patch?
Regards
Joseph
On 2016-02-08 22:29, Joseph C. Lehner wrote:
> This patch adds support for the Netgear EX2700 and builds an approriate
> sysupgrade image.
>
> What's missing is the option to build a factory image flashable via the
> router's stock web interface, but this approach is hindered by the fact
> that u-boot operforms an additional integrity check, which expects a
> uImage header in the last 64 bytes of the "kernel" partition, which
> the bootloader expects to be 960k, a size exceeded by the standard
> OpenWrt kernel.
>
> Signed-off-by: Joseph C. Lehner <joseph.c.lehner at gmail.com>
>
> ---
> Changes for v4:
> * Fix whitespace errors in netgear.mk
>
> Changes for v3:
> * Fix led name in /etc/board.d/01_leds
> * Cleanup device tree
>
> Changes for v2:
> * Fix alphabetical ordering (image/Makefile is not really sorted, so I've
> put the EX2700 immediately below the E1700).
>
> diff --git a/target/linux/ramips/base-files/etc/board.d/01_leds b/target/linux/ramips/base-files/etc/board.d/01_leds
> index c3a81a4..b10f5f1 100755
> --- a/target/linux/ramips/base-files/etc/board.d/01_leds
> +++ b/target/linux/ramips/base-files/etc/board.d/01_leds
> @@ -125,6 +125,10 @@ dir-810l|\
> mzk-dp150n)
> ucidef_set_led_default "power" "power" "$board:green:power" "1"
> ;;
> +ex2700)
> + ucidef_set_led_default "power_r" "POWER (red)" "$board:red:power" "0"
> + set_wifi_led "$board:green:router"
> + ;;
> f5d8235-v1|\
> f5d8235-v2)
> set_usb_led "$board:blue:storage"
> diff --git a/target/linux/ramips/base-files/etc/board.d/02_network b/target/linux/ramips/base-files/etc/board.d/02_network
> index dafa3e9..9853729 100755
> --- a/target/linux/ramips/base-files/etc/board.d/02_network
> +++ b/target/linux/ramips/base-files/etc/board.d/02_network
> @@ -141,7 +141,8 @@ ramips_setup_interfaces()
> ucidef_add_switch "switch0" \
> "1:lan" "2:lan" "3:lan" "4:lan" "0:wan" "9 at eth0"
> ;;
> - cf-wr800n)
> + cf-wr800n|\
> + ex2700)
> ucidef_add_switch "switch0" \
> "4:lan" "6t at eth0"
> ;;
> diff --git a/target/linux/ramips/base-files/etc/diag.sh b/target/linux/ramips/base-files/etc/diag.sh
> index acc500b..59c5965 100644
> --- a/target/linux/ramips/base-files/etc/diag.sh
> +++ b/target/linux/ramips/base-files/etc/diag.sh
> @@ -34,6 +34,7 @@ get_status_led() {
> a5-v11|\
> d105|\
> dcs-930l-b1|\
> + ex2700|\
> hlk-rm04|\
> mpr-a1|\
> mpr-a2)
> diff --git a/target/linux/ramips/base-files/lib/ramips.sh b/target/linux/ramips/base-files/lib/ramips.sh
> index 8025a40..aed8350 100755
> --- a/target/linux/ramips/base-files/lib/ramips.sh
> +++ b/target/linux/ramips/base-files/lib/ramips.sh
> @@ -154,6 +154,9 @@ ramips_board_detect() {
> *"ESR-9753")
> name="esr-9753"
> ;;
> + *"EX2700")
> + name="ex2700";
> + ;;
> *"F5D8235 v1")
> name="f5d8235-v1"
> ;;
> diff --git a/target/linux/ramips/base-files/lib/upgrade/platform.sh b/target/linux/ramips/base-files/lib/upgrade/platform.sh
> index 39b5f94..78edd22 100755
> --- a/target/linux/ramips/base-files/lib/upgrade/platform.sh
> +++ b/target/linux/ramips/base-files/lib/upgrade/platform.sh
> @@ -51,6 +51,7 @@ platform_check_image() {
> dir-810l|\
> e1700|\
> esr-9753|\
> + ex2700|\
> f7c027|\
> firewrt|\
> fonera20n|\
> diff --git a/target/linux/ramips/dts/EX2700.dts b/target/linux/ramips/dts/EX2700.dts
> new file mode 100644
> index 0000000..4b5a01a
> --- /dev/null
> +++ b/target/linux/ramips/dts/EX2700.dts
> @@ -0,0 +1,148 @@
> +/*
> + * Device Tree file for the Netgear EX2700
> + *
> + * Copyright (C) 2016 Joseph C. Lehner <joseph.c.lehner at gmail.com>
> + *
> + * This file is licensed under the terms of the GNU General Public
> + * License version 2. This program is licensed "as is" without any
> + * warranty of any kind, whether express or implied.
> + */
> +
> +/dts-v1/;
> +
> +/include/ "mt7620a.dtsi"
> +
> +/ {
> + compatible = "ralink,mt7620a-soc";
> + model = "Netgear EX2700";
> +
> + chosen {
> + bootargs = "console=ttyS0,57600";
> + };
> +
> + palmbus at 10000000 {
> +
> + gpio0: gpio at 600 {
> + status = "okay";
> + };
> +
> + gpio1: gpio at 638 {
> + status = "okay";
> + };
> +
> + spi at b00 {
> + status = "okay";
> +
> + m25p80 at 0 {
> + #address-cells = <1>;
> + #size-cells = <1>;
> + compatible = "jedec,spi-nor";
> + reg = <0 0>;
> + linux,modalias = "m25p80", "mx25l3205d";
> + spi-max-frequency = <10000000>;
> +
> + partition at 0 {
> + label = "u-boot";
> + reg = <0x0 0x30000>;
> + read-only;
> + };
> +
> + partition at 30000 {
> + label = "u-boot-env";
> + reg = <0x30000 0x10000>;
> + read-only;
> + };
> +
> + partition at 40000 {
> + label = "firmware";
> + reg = <0x40000 0x3b0000>;
> + };
> +
> + art: partition at 3f0000 {
> + label = "art";
> + reg = <0x3f0000 0x10000>;
> + read-only;
> + };
> + };
> + };
> + };
> +
> + ethernet at 10100000 {
> + mtd-mac-address = <&art 0x0>;
> + };
> +
> + wmac at 10180000 {
> + ralink,mtd-eeprom = <&art 0x1000>;
> + };
> +
> + pinctrl {
> + state_default: pinctrl0 {
> + default {
> + // spi refclk: pins 37, 38, 39
> + // uartf: pins 8, 9, 10, 11, 12, 13, 14
> + // i2c: pins 1, 2
> + ralink,group = "i2c", "uartf", "spi refclk";
> + ralink,function = "gpio";
> + };
> + };
> + };
> +
> + gpio-leds {
> + compatible = "gpio-leds";
> +
> + power_g {
> + label = "ex2700:green:power";
> + gpios = <&gpio0 9 1>;
> + default-state = "on";
> + };
> +
> + power_r {
> + label = "ex2700:red:power";
> + gpios = <&gpio0 11 1>;
> + };
> +
> + device_g {
> + label = "ex2700:green:device";
> + gpios = <&gpio0 13 1>;
> + };
> +
> + device_r {
> + label = "ex2700:red:device";
> + gpios = <&gpio0 10 1>;
> + };
> +
> + router_g {
> + label = "ex2700:green:router";
> + gpios = <&gpio0 12 1>;
> + };
> +
> + router_r {
> + label = "ex2700:red:router";
> + gpios = <&gpio0 14 1>;
> + };
> +
> + wps {
> + label = "ex2700:green:wps";
> + gpios = <&gpio1 15 1>;
> + };
> + };
> +
> + gpio-keys-polled {
> + compatible = "gpio-keys-polled";
> + #address-cells = <1>;
> + #size-cells = <0>;
> + poll-interval = <20>;
> +
> + reset {
> + label = "reset";
> + gpios = <&gpio0 1 1>;
> + linux,code = <0x198>;
> + };
> +
> + wps {
> + label = "wps";
> + gpios = <&gpio0 2 1>;
> + linux,code = <0x211>;
> + };
> + };
> +};
> diff --git a/target/linux/ramips/image/Makefile b/target/linux/ramips/image/Makefile
> index 55b9cf4..adeea25 100644
> --- a/target/linux/ramips/image/Makefile
> +++ b/target/linux/ramips/image/Makefile
> @@ -913,6 +913,7 @@ endif
> #
>
> Image/Build/Profile/E1700=$(call BuildFirmware/UMedia/$(1),$(1),e1700,E1700,0x013326)
> +Image/Build/Profile/EX2700=$(call BuildFirmware/Default4M/$(1),$(1),ex2700,EX2700)
> Image/Build/Profile/MT7620a=$(call BuildFirmware/Default8M/$(1),$(1),mt7620a,MT7620a)
> Image/Build/Profile/MT7620a_MT7610e=$(call BuildFirmware/Default8M/$(1),$(1),mt7620a_mt7610e,MT7620a_MT7610e)
> Image/Build/Profile/MT7620a_MT7530=$(call BuildFirmware/Default8M/$(1),$(1),mt7620a_mt7530,MT7620a_MT7530)
> @@ -958,6 +959,7 @@ Image/Build/Profile/TINY-AC=$(call BuildFirmware/Default8M/$(1),$(1),tiny-ac,TIN
> ifeq ($(SUBTARGET),mt7620)
> define Image/Build/Profile/Default
> $(call Image/Build/Profile/E1700,$(1))
> + $(call Image/Build/Profile/EX2700,$(1))
> $(call Image/Build/Profile/MT7620a,$(1))
> $(call Image/Build/Profile/MT7620a_MT7610e,$(1))
> $(call Image/Build/Profile/MT7620a_MT7530,$(1))
> diff --git a/target/linux/ramips/mt7620/profiles/netgear.mk b/target/linux/ramips/mt7620/profiles/netgear.mk
> new file mode 100644
> index 0000000..590756a
> --- /dev/null
> +++ b/target/linux/ramips/mt7620/profiles/netgear.mk
> @@ -0,0 +1,16 @@
> +#
> +# Copyright (C) 2016 OpenWrt.org
> +#
> +# This is free software, licensed under the GNU General Public License v2.
> +# See /LICENSE for more information.
> +#
> +
> +define Profile/EX2700
> + NAME:=Netgear EX2700
> + PACKAGES:=-kmod-usb-core -kmod-usb2 -kmod-usb-ohci -kmod-ledtrig-usbdev
> +endef
> +
> +define Profile/EX2700/Description
> + Support for Netgear EX2700
> +endef
> +$(eval $(call Profile,EX2700))
>
>
> On 2016-02-08 08:44, John Crispin wrote:
>> Hi,
>>
>> the patch is whitespace broken. please fix and resend
>>
>> John
>
_______________________________________________
openwrt-devel mailing list
openwrt-devel at lists.openwrt.org
https://lists.openwrt.org/cgi-bin/mailman/listinfo/openwrt-devel
More information about the openwrt-devel
mailing list