[OpenWrt-Devel] [PATCH] ramips: add support for ZBT WG2626
Daniel Golle
daniel at makrotopia.org
Thu Oct 29 23:05:37 EDT 2015
Signed-off-by: Daniel Golle <daniel at makrotopia.org>
---
Note that HIGHMEM support apparently breaks spi-mt7621 and thus access
to the SPI-NOR flash. As a work-around, one can limit the memory
to 256MB which fixes the issue.
.../linux/ramips/base-files/etc/board.d/02_network | 3 +-
target/linux/ramips/base-files/etc/diag.sh | 3 +-
target/linux/ramips/base-files/lib/ramips.sh | 3 +
.../ramips/base-files/lib/upgrade/platform.sh | 1 +
target/linux/ramips/dts/ZBT-WG2626.dts | 127 +++++++++++++++++++++
target/linux/ramips/image/Makefile | 7 +-
target/linux/ramips/mt7621/profiles/zbt.mk | 20 ++++
7 files changed, 161 insertions(+), 3 deletions(-)
create mode 100644 target/linux/ramips/dts/ZBT-WG2626.dts
create mode 100644 target/linux/ramips/mt7621/profiles/zbt.mk
diff --git a/target/linux/ramips/base-files/etc/board.d/02_network b/target/linux/ramips/base-files/etc/board.d/02_network
index 0732796..2a26486 100755
--- a/target/linux/ramips/base-files/etc/board.d/02_network
+++ b/target/linux/ramips/base-files/etc/board.d/02_network
@@ -83,7 +83,8 @@ ramips_setup_interfaces()
wsr-1166|\
wsr-600|\
wt1520|\
- y1)
+ y1|\
+ zbt-wg2626)
ucidef_set_interfaces_lan_wan "eth0.1" "eth0.2"
ucidef_add_switch "switch0" "1" "1"
ucidef_add_switch_vlan "switch0" "1" "0 1 2 3 6t"
diff --git a/target/linux/ramips/base-files/etc/diag.sh b/target/linux/ramips/base-files/etc/diag.sh
index 5376759..e0dd92a 100644
--- a/target/linux/ramips/base-files/etc/diag.sh
+++ b/target/linux/ramips/base-files/etc/diag.sh
@@ -62,7 +62,8 @@ get_status_led() {
rut5xx|\
v11st-fe|\
vocore|\
- wmr-300)
+ wmr-300|\
+ zbt-wg2626)
status_led="$board:green:status"
;;
atp-52b|\
diff --git a/target/linux/ramips/base-files/lib/ramips.sh b/target/linux/ramips/base-files/lib/ramips.sh
index 4072a31..a0f8e4e 100755
--- a/target/linux/ramips/base-files/lib/ramips.sh
+++ b/target/linux/ramips/base-files/lib/ramips.sh
@@ -454,6 +454,9 @@ ramips_board_detect() {
*"ZBT-WA05")
name="zbt-wa05"
;;
+ *"ZBT-WG2626")
+ name="zbt-wg2626"
+ ;;
*"ZBT-WR8305RT")
name="zbt-wr8305rt"
;;
diff --git a/target/linux/ramips/base-files/lib/upgrade/platform.sh b/target/linux/ramips/base-files/lib/upgrade/platform.sh
index d3d9df3..22120da 100755
--- a/target/linux/ramips/base-files/lib/upgrade/platform.sh
+++ b/target/linux/ramips/base-files/lib/upgrade/platform.sh
@@ -131,6 +131,7 @@ platform_check_image() {
y1|\
y1s|\
zbt-wa05|\
+ zbt-wg2626|\
zbt-wr8305rt|\
zte-q7)
[ "$magic" != "27051956" ] && {
diff --git a/target/linux/ramips/dts/ZBT-WG2626.dts b/target/linux/ramips/dts/ZBT-WG2626.dts
new file mode 100644
index 0000000..6170454
--- /dev/null
+++ b/target/linux/ramips/dts/ZBT-WG2626.dts
@@ -0,0 +1,127 @@
+/dts-v1/;
+
+/include/ "mt7621.dtsi"
+
+/ {
+ compatible = "mediatek,mt7621-eval-board", "mediatek,mt7621-soc";
+ model = "ZBT-WG2626";
+
+ memory at 0 {
+ device_type = "memory";
+ reg = <0x0 0x1c000000>, <0x20000000 0x4000000>;
+ };
+
+ chosen {
+ bootargs = "console=ttyS0,57600";
+ };
+
+ sdhci at 10130000 {
+ status = "okay";
+ };
+
+ palmbus at 1E000000 {
+ spi at b00 {
+ status = "okay";
+
+ m25p80 at 0 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "w25q128";
+ reg = <0 0>;
+ linux,modalias = "m25p80";
+ spi-max-frequency = <10000000>;
+
+ partition at 0 {
+ label = "u-boot";
+ reg = <0x0 0x30000>;
+ read-only;
+ };
+
+ partition at 30000 {
+ label = "u-boot-env";
+ reg = <0x30000 0x10000>;
+ read-only;
+ };
+
+ factory: partition at 40000 {
+ label = "factory";
+ reg = <0x40000 0x10000>;
+ read-only;
+ };
+
+ partition at 50000 {
+ label = "firmware";
+ reg = <0x50000 0xfb0000>;
+ };
+
+ };
+ };
+
+ i2c at 900 {
+ compatible = "ralink,i2c-mt7621";
+ reg = <0x900 0x100>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c_pins>;
+ status = "okay";
+ };
+ };
+
+ pcie at 1e140000 {
+ status = "okay";
+
+ pcie0 {
+ mt76 at 0,0 {
+ reg = <0x0000 0 0 0 0>;
+ device_type = "pci";
+ mediatek,mtd-eeprom = <&factory 0x8000>;
+ mediatek,2ghz = <0>;
+ };
+ };
+
+ pcie1 {
+ mt76 at 1,0 {
+ reg = <0x0000 0 0 0 0>;
+ device_type = "pci";
+ mediatek,mtd-eeprom = <&factory 0x0000>;
+ mediatek,5ghz = <0>;
+ };
+ };
+ };
+
+ ethernet at 1e100000 {
+ mtd-mac-address = <&factory 0xe000>;
+ };
+
+ gpio-keys-polled {
+ compatible = "gpio-keys-polled";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ poll-interval = <20>;
+
+ reset {
+ label = "reset";
+ gpios = <&gpio0 18 1>;
+ linux,code = <0x198>;
+ };
+ };
+
+ gpio-leds {
+ compatible = "gpio-leds";
+
+ status {
+ label = "zbt-wg2626:green:status";
+ gpios = <&gpio0 24 1>;
+ };
+ };
+
+ pinctrl {
+ state_default: pinctrl0 {
+ gpio {
+ ralink,group = "wdt", "rgmii2", "wdt rst", "jtag", "mdio";
+ ralink,function = "gpio";
+ };
+ };
+ };
+};
diff --git a/target/linux/ramips/image/Makefile b/target/linux/ramips/image/Makefile
index 5fee8ff..1c03a06 100644
--- a/target/linux/ramips/image/Makefile
+++ b/target/linux/ramips/image/Makefile
@@ -952,7 +952,7 @@ endif
#
ifeq ($(SUBTARGET),mt7621)
- TARGET_DEVICES += mt7621 wsr-600 wsr-1166 dir-860l-b1 firewrt pbr-m1 re6500 sap-g3200u3
+ TARGET_DEVICES += mt7621 wsr-600 wsr-1166 dir-860l-b1 firewrt pbr-m1 re6500 sap-g3200u3 zbt-wg2626
endif
define Device/mt7621
@@ -1002,6 +1002,11 @@ define Device/sap-g3200u3
DTS := SAP-G3200U3
endef
+define Device/zbt-wg2626
+ DTS := ZBT-WG2626
+ IMAGE_SIZE := $(ralink_default_fw_size_16M)
+endef
+
#
# MT7628 Profiles
#
diff --git a/target/linux/ramips/mt7621/profiles/zbt.mk b/target/linux/ramips/mt7621/profiles/zbt.mk
new file mode 100644
index 0000000..e6ef6ad
--- /dev/null
+++ b/target/linux/ramips/mt7621/profiles/zbt.mk
@@ -0,0 +1,20 @@
+#
+# Copyright (C) 2015 OpenWrt.org
+#
+# This is free software, licensed under the GNU General Public License v2.
+# See /LICENSE for more information.
+#
+
+define Profile/ZBT-WG2626
+ NAME:=ZBT-WG2626 Device
+ FEATURES+=rtc
+ PACKAGES:=\
+ kmod-usb-core kmod-usb3 kmod-sdhci-mt7620 \
+ kmod-ledtrig-usbdev kmod-ata-core kmod-ata-ahci \
+ kmod-usb3-mt7621
+endef
+
+define Profile/ZBT-WG2626/Description
+ Package set for ZBT-WG2626 device
+endef
+$(eval $(call Profile,ZBT-WG2626))
--
2.6.2
_______________________________________________
openwrt-devel mailing list
openwrt-devel at lists.openwrt.org
https://lists.openwrt.org/cgi-bin/mailman/listinfo/openwrt-devel
More information about the openwrt-devel
mailing list