[OpenWrt-Devel] [PATCH] ramips: add support for Youku YK1
John Crispin
blogic at openwrt.org
Sat Nov 21 13:05:13 EST 2015
Hi
1 comment inline
On 08/11/2015 07:08, Shonn Lu wrote:
> Signed-off-by: Shonn Lu <countrysideboy at qq.com>
> ---
> target/linux/ramips/base-files/etc/board.d/01_leds | 5 +
> .../linux/ramips/base-files/etc/board.d/02_network | 1 +
> target/linux/ramips/base-files/lib/ramips.sh | 3 +
> .../ramips/base-files/lib/upgrade/platform.sh | 1 +
> target/linux/ramips/dts/Youku-YK1.dts | 127 +++++++++++++++++++++
> target/linux/ramips/image/Makefile | 2 +
> 6 files changed, 139 insertions(+)
> create mode 100644 target/linux/ramips/dts/Youku-YK1.dts
>
> diff --git a/target/linux/ramips/base-files/etc/board.d/01_leds b/target/linux/ramips/base-files/etc/board.d/01_leds
> index 545bd70..bc86bd3 100755
> --- a/target/linux/ramips/base-files/etc/board.d/01_leds
> +++ b/target/linux/ramips/base-files/etc/board.d/01_leds
> @@ -261,6 +261,11 @@ case $board in
> zte-q7)
> set_wifi_led "zte:blue:status"
> ;;
> + yk1)
> + ucidef_set_led_default "power" "power" "youku:blue:power" "1"
> + set_wifi_led "youku:blue:air"
> + set_usb_led "youku:blue:usb"
> + ;;
> esac
>
> board_config_flush
> diff --git a/target/linux/ramips/base-files/etc/board.d/02_network b/target/linux/ramips/base-files/etc/board.d/02_network
> index 19ef3f7..3c87971 100755
> --- a/target/linux/ramips/base-files/etc/board.d/02_network
> +++ b/target/linux/ramips/base-files/etc/board.d/02_network
> @@ -145,6 +145,7 @@ ramips_setup_interfaces()
> wsr-1166 | \
> wt1520 | \
> xiaomi-miwifi-mini |\
> + yk1 |\
> y1)
> ucidef_set_interfaces_lan_wan "eth0.1" "eth0.2"
> ucidef_add_switch "switch0" "1" "1"
> diff --git a/target/linux/ramips/base-files/lib/ramips.sh b/target/linux/ramips/base-files/lib/ramips.sh
> index a9a6664..bdd6d4e 100755
> --- a/target/linux/ramips/base-files/lib/ramips.sh
> +++ b/target/linux/ramips/base-files/lib/ramips.sh
> @@ -409,6 +409,9 @@ ramips_board_detect() {
> *"ZTE Q7")
> name="zte-q7"
> ;;
> + *"Youku YK1")
> + name="yk1"
> + ;;
> *"Lenovo Y1")
> name="y1"
the patch applies to a trunk prior to our cleanup. the patch wont apply
because of this. please rebase it on current trunk and resend
John
> ;;
> diff --git a/target/linux/ramips/base-files/lib/upgrade/platform.sh b/target/linux/ramips/base-files/lib/upgrade/platform.sh
> index 11fee85..66fcd04 100755
> --- a/target/linux/ramips/base-files/lib/upgrade/platform.sh
> +++ b/target/linux/ramips/base-files/lib/upgrade/platform.sh
> @@ -127,6 +127,7 @@ platform_check_image() {
> y1 |\
> y1s |\
> zte-q7 |\
> + yk1 |\
> zbt-wa05)
> [ "$magic" != "27051956" ] && {
> echo "Invalid image type."
> diff --git a/target/linux/ramips/dts/Youku-YK1.dts b/target/linux/ramips/dts/Youku-YK1.dts
> new file mode 100644
> index 0000000..10662d3
> --- /dev/null
> +++ b/target/linux/ramips/dts/Youku-YK1.dts
> @@ -0,0 +1,127 @@
> +/dts-v1/;
> +
> +/include/ "mt7620a.dtsi"
> +
> +/ {
> + compatible = "Youku-YK1", "ralink,mt7620a-soc";
> + model = "Youku YK1";
> +
> + palmbus at 10000000 {
> +
> + gpio0: gpio at 600 {
> + status = "okay";
> + };
> +
> + gpio1: gpio at 638 {
> + status = "okay";
> + };
> +
> + gpio2: gpio at 660 {
> + status = "okay";
> + };
> +
> + gpio3: gpio at 688 {
> + status = "okay";
> + };
> +
> + spi at b00 {
> + status = "okay";
> +
> + m25p80 at 0 {
> + #address-cells = <1>;
> + #size-cells = <1>;
> + compatible = "w25q256";
> + reg = <0 0>;
> + linux,modalias = "m25p80", "w25q256";
> + spi-max-frequency = <10000000>;
> +
> + partition at 0 {
> + label = "u-boot";
> + reg = <0x0 0x30000>;
> + read-only;
> + };
> +
> + partition at 30000 {
> + label = "u-boot-env";
> + reg = <0x30000 0x10000>;
> + read-only;
> + };
> +
> + factory: partition at 40000 {
> + label = "factory";
> + reg = <0x40000 0x10000>;
> + read-only;
> + };
> +
> + partition at 50000 {
> + label = "firmware";
> + reg = <0x50000 0x1fb0000>;
> + };
> + };
> + };
> + };
> +
> + pinctrl {
> + state_default: pinctrl0 {
> + default {
> + ralink,group = "i2c", "uartf", "rgmii1", "rgmii2", "ephy", "wled", "nd_sd";
> + ralink,function = "gpio";
> + };
> + };
> + };
> +
> + ethernet at 10100000 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&ephy_pins>;
> + mtd-mac-address = <&factory 0x4>;
> + ralink,port-map = "llllw";
> + };
> +
> + wmac at 10180000 {
> + ralink,mtd-eeprom = <&factory 0>;
> + };
> +
> + sdhci at b0130000 {
> + status = "okay";
> + };
> +
> + ehci at 101c0000 {
> + status = "okay";
> + };
> +
> + ohci at 101c1000 {
> + status = "okay";
> + };
> +
> + gpio-leds {
> + compatible = "gpio-leds";
> + wan {
> + label = "youku:blue:wan";
> + gpios = <&gpio2 4 1>;
> + };
> + air {
> + label = "youku:blue:air";
> + gpios = <&gpio3 0 1>;
> + };
> + usb {
> + label = "youku:blue:usb";
> + gpios = <&gpio1 11 1>;
> + };
> + power {
> + label = "youku:blue:power";
> + gpios = <&gpio1 5 1>;
> + };
> + };
> +
> + gpio-keys-polled {
> + compatible = "gpio-keys-polled";
> + #address-cells = <1>;
> + #size-cells = <0>;
> + poll-interval = <20>;
> + reset {
> + label = "reset";
> + gpios = <&gpio0 1 1>;
> + linux,code = <0x198>;
> + };
> + };
> +};
> diff --git a/target/linux/ramips/image/Makefile b/target/linux/ramips/image/Makefile
> index b4d0897..ca320d3 100644
> --- a/target/linux/ramips/image/Makefile
> +++ b/target/linux/ramips/image/Makefile
> @@ -884,6 +884,7 @@ Image/Build/Profile/WRTNODE=$(call BuildFirmware/Default16M/$(1),$(1),wrtnode,WR
> Image/Build/Profile/WT3020=$(call BuildFirmware/PorayDualSize/$(1),$(1),wt3020,WT3020)
> Image/Build/Profile/XIAOMI-MIWIFI-MINI=$(call BuildFirmware/Default16M/$(1),$(1),xiaomi-miwifi-mini,XIAOMI-MIWIFI-MINI)
> Image/Build/Profile/ZTE-Q7=$(call BuildFirmware/Default8M/$(1),$(1),zte-q7,ZTE-Q7)
> +Image/Build/Profile/Youku-YK1=$(call BuildFirmware/Default32M/$(1),$(1),youku-yk1,Youku-YK1)
> Image/Build/Profile/ZBT-WA05=$(call BuildFirmware/Default8M/$(1),$(1),zbt-wa05,ZBT-WA05)
> Image/Build/Profile/ArcherC20i=$(call BuildFirmware/Tplink/$(1),$(1),ArcherC20i,ArcherC20i)
> microwrt_mtd_size=16515072
> @@ -917,6 +918,7 @@ define Image/Build/Profile/Default
> $(call Image/Build/Profile/WT3020,$(1))
> $(call Image/Build/Profile/XIAOMI-MIWIFI-MINI,$(1))
> $(call Image/Build/Profile/ZTE-Q7,$(1))
> + $(call Image/Build/Profile/Youku-YK1,$(1))
> $(call Image/Build/Profile/ZBT-WA05,$(1))
> $(call Image/Build/Profile/ArcherC20i,$(1))
> $(call Image/Build/Profile/MicroWRT,$(1))
>
_______________________________________________
openwrt-devel mailing list
openwrt-devel at lists.openwrt.org
https://lists.openwrt.org/cgi-bin/mailman/listinfo/openwrt-devel
More information about the openwrt-devel
mailing list