[OpenWrt-Devel] [PATCH 4/5] ipq806x: add & enable cpufreq support
Mathieu Olivari
mathieu at codeaurora.org
Wed May 20 23:37:47 EDT 2015
This change set enables frequency scaling on ipq806x, which speeds-up
the CPU and allows it to achieve its max frequency.
These patches are cherry-picked & backported from the following location:
*130-132: linux-next
*133-143: LKML - https://lkml.org/lkml/2015/3/21/15
*144: derived from other qcom similar dts
*145: derived from https://chromium.googlesource.com/chromiumos/third_party/kernel/+/chromeos-3.14/drivers/cpufreq/cpufreq-krait.c
Signed-off-by: Mathieu Olivari <mathieu at codeaurora.org>
---
target/linux/ipq806x/config-3.18 | 24 ++
target/linux/ipq806x/config-4.0 | 25 ++
...-set_parent-doing-the-wrong-thing-when-IN.patch | 60 +++
...-clk-Add-__clk_mux_determine_rate_closest.patch | 120 ++++++
..._unregister_-divider-gate-mux-to-close-me.patch | 115 +++++
...-Add-Krait-L2-register-accessor-functions.patch | 144 +++++++
...ux-Split-out-register-accessors-for-reuse.patch | 192 +++++++++
...ates-to-downstream-clocks-during-set_rate.patch | 129 ++++++
.../136-clk-Add-safe-switch-hook.patch | 170 ++++++++
...dd-support-for-High-Frequency-PLLs-HFPLLs.patch | 351 ++++++++++++++++
.../138-clk-qcom-Add-HFPLL-driver.patch | 206 +++++++++
.../139-clk-qcom-Add-IPQ806X-s-HFPLLs.patch | 127 ++++++
...140-clk-qcom-Add-support-for-Krait-clocks.patch | 271 ++++++++++++
.../141-clk-qcom-Add-KPSS-ACC-GCC-driver.patch | 205 +++++++++
...lk-qcom-Add-Krait-clock-controller-driver.patch | 435 +++++++++++++++++++
...-module-to-register-cpufreq-on-Krait-CPUs.patch | 304 ++++++++++++++
...m-Add-necessary-DT-data-for-Krait-cpufreq.patch | 100 +++++
...ufreq-Add-a-cpufreq-krait-based-on-cpufre.patch | 461 +++++++++++++++++++++
.../patches-3.18/700-add-gmac-dts-suport.patch | 2 +-
...-Add-Krait-L2-register-accessor-functions.patch | 144 +++++++
...ux-Split-out-register-accessors-for-reuse.patch | 192 +++++++++
...ates-to-downstream-clocks-during-set_rate.patch | 130 ++++++
.../patches-4.0/136-clk-Add-safe-switch-hook.patch | 164 ++++++++
...dd-support-for-High-Frequency-PLLs-HFPLLs.patch | 351 ++++++++++++++++
.../138-clk-qcom-Add-HFPLL-driver.patch | 206 +++++++++
.../139-clk-qcom-Add-IPQ806X-s-HFPLLs.patch | 127 ++++++
...140-clk-qcom-Add-support-for-Krait-clocks.patch | 271 ++++++++++++
.../141-clk-qcom-Add-KPSS-ACC-GCC-driver.patch | 205 +++++++++
...lk-qcom-Add-Krait-clock-controller-driver.patch | 435 +++++++++++++++++++
...-module-to-register-cpufreq-on-Krait-CPUs.patch | 304 ++++++++++++++
...m-Add-necessary-DT-data-for-Krait-cpufreq.patch | 100 +++++
...ufreq-Add-a-cpufreq-krait-based-on-cpufre.patch | 461 +++++++++++++++++++++
.../patches-4.0/700-add-gmac-dts-suport.patch | 2 +-
33 files changed, 6531 insertions(+), 2 deletions(-)
create mode 100644 target/linux/ipq806x/patches-3.18/130-clk_mux-Fix-set_parent-doing-the-wrong-thing-when-IN.patch
create mode 100644 target/linux/ipq806x/patches-3.18/131-clk-Add-__clk_mux_determine_rate_closest.patch
create mode 100644 target/linux/ipq806x/patches-3.18/132-clk-Add-clk_unregister_-divider-gate-mux-to-close-me.patch
create mode 100644 target/linux/ipq806x/patches-3.18/133-ARM-Add-Krait-L2-register-accessor-functions.patch
create mode 100644 target/linux/ipq806x/patches-3.18/134-clk-mux-Split-out-register-accessors-for-reuse.patch
create mode 100644 target/linux/ipq806x/patches-3.18/135-clk-Avoid-sending-high-rates-to-downstream-clocks-during-set_rate.patch
create mode 100644 target/linux/ipq806x/patches-3.18/136-clk-Add-safe-switch-hook.patch
create mode 100644 target/linux/ipq806x/patches-3.18/137-clk-qcom-Add-support-for-High-Frequency-PLLs-HFPLLs.patch
create mode 100644 target/linux/ipq806x/patches-3.18/138-clk-qcom-Add-HFPLL-driver.patch
create mode 100644 target/linux/ipq806x/patches-3.18/139-clk-qcom-Add-IPQ806X-s-HFPLLs.patch
create mode 100644 target/linux/ipq806x/patches-3.18/140-clk-qcom-Add-support-for-Krait-clocks.patch
create mode 100644 target/linux/ipq806x/patches-3.18/141-clk-qcom-Add-KPSS-ACC-GCC-driver.patch
create mode 100644 target/linux/ipq806x/patches-3.18/142-clk-qcom-Add-Krait-clock-controller-driver.patch
create mode 100644 target/linux/ipq806x/patches-3.18/143-cpufreq-Add-module-to-register-cpufreq-on-Krait-CPUs.patch
create mode 100644 target/linux/ipq806x/patches-3.18/144-ARM-dts-qcom-Add-necessary-DT-data-for-Krait-cpufreq.patch
create mode 100644 target/linux/ipq806x/patches-3.18/145-cpufreq-Add-a-cpufreq-krait-based-on-cpufre.patch
create mode 100644 target/linux/ipq806x/patches-4.0/133-ARM-Add-Krait-L2-register-accessor-functions.patch
create mode 100644 target/linux/ipq806x/patches-4.0/134-clk-mux-Split-out-register-accessors-for-reuse.patch
create mode 100644 target/linux/ipq806x/patches-4.0/135-clk-Avoid-sending-high-rates-to-downstream-clocks-during-set_rate.patch
create mode 100644 target/linux/ipq806x/patches-4.0/136-clk-Add-safe-switch-hook.patch
create mode 100644 target/linux/ipq806x/patches-4.0/137-clk-qcom-Add-support-for-High-Frequency-PLLs-HFPLLs.patch
create mode 100644 target/linux/ipq806x/patches-4.0/138-clk-qcom-Add-HFPLL-driver.patch
create mode 100644 target/linux/ipq806x/patches-4.0/139-clk-qcom-Add-IPQ806X-s-HFPLLs.patch
create mode 100644 target/linux/ipq806x/patches-4.0/140-clk-qcom-Add-support-for-Krait-clocks.patch
create mode 100644 target/linux/ipq806x/patches-4.0/141-clk-qcom-Add-KPSS-ACC-GCC-driver.patch
create mode 100644 target/linux/ipq806x/patches-4.0/142-clk-qcom-Add-Krait-clock-controller-driver.patch
create mode 100644 target/linux/ipq806x/patches-4.0/143-cpufreq-Add-module-to-register-cpufreq-on-Krait-CPUs.patch
create mode 100644 target/linux/ipq806x/patches-4.0/144-ARM-dts-qcom-Add-necessary-DT-data-for-Krait-cpufreq.patch
create mode 100644 target/linux/ipq806x/patches-4.0/145-cpufreq-Add-a-cpufreq-krait-based-on-cpufre.patch
diff --git a/target/linux/ipq806x/config-3.18 b/target/linux/ipq806x/config-3.18
index 1e08f36..2f5954c 100644
--- a/target/linux/ipq806x/config-3.18
+++ b/target/linux/ipq806x/config-3.18
@@ -40,10 +40,12 @@ CONFIG_ARM_ARCH_TIMER_EVTSTREAM=y
CONFIG_ARM_CPU_SUSPEND=y
CONFIG_ARM_GIC=y
CONFIG_ARM_HAS_SG_CHAIN=y
+# CONFIG_ARM_KIRKWOOD_CPUFREQ is not set
CONFIG_ARM_L1_CACHE_SHIFT=6
CONFIG_ARM_L1_CACHE_SHIFT_6=y
# CONFIG_ARM_LPAE is not set
CONFIG_ARM_PATCH_PHYS_VIRT=y
+CONFIG_ARM_QCOM_CPUFREQ=y
# CONFIG_ARM_SP805_WATCHDOG is not set
CONFIG_ARM_THUMB=y
# CONFIG_ARM_THUMBEE is not set
@@ -64,6 +66,7 @@ CONFIG_COMMON_CLK=y
CONFIG_COMMON_CLK_QCOM=y
CONFIG_COMPACTION=y
CONFIG_COREDUMP=y
+# CONFIG_CPUFREQ_DT is not set
CONFIG_CPU_32v6K=y
CONFIG_CPU_32v7=y
CONFIG_CPU_ABRT_EV7=y
@@ -73,11 +76,25 @@ CONFIG_CPU_CACHE_VIPT=y
CONFIG_CPU_COPY_V6=y
CONFIG_CPU_CP15=y
CONFIG_CPU_CP15_MMU=y
+CONFIG_CPU_FREQ=y
+# CONFIG_CPU_FREQ_DEFAULT_GOV_CONSERVATIVE is not set
+# CONFIG_CPU_FREQ_DEFAULT_GOV_ONDEMAND is not set
+CONFIG_CPU_FREQ_DEFAULT_GOV_PERFORMANCE=y
+# CONFIG_CPU_FREQ_DEFAULT_GOV_POWERSAVE is not set
+# CONFIG_CPU_FREQ_DEFAULT_GOV_USERSPACE is not set
+# CONFIG_CPU_FREQ_GOV_CONSERVATIVE is not set
+# CONFIG_CPU_FREQ_GOV_ONDEMAND is not set
+CONFIG_CPU_FREQ_GOV_PERFORMANCE=y
+# CONFIG_CPU_FREQ_GOV_POWERSAVE is not set
+# CONFIG_CPU_FREQ_GOV_USERSPACE is not set
+CONFIG_CPU_FREQ_STAT=y
+# CONFIG_CPU_FREQ_STAT_DETAILS is not set
CONFIG_CPU_HAS_ASID=y
# CONFIG_CPU_ICACHE_DISABLE is not set
CONFIG_CPU_PABRT_V7=y
CONFIG_CPU_PM=y
CONFIG_CPU_RMAP=y
+# CONFIG_CPU_THERMAL is not set
CONFIG_CPU_TLB_V7=y
CONFIG_CPU_V7=y
CONFIG_CRC16=y
@@ -111,6 +128,7 @@ CONFIG_GENERIC_BUG=y
CONFIG_GENERIC_CLOCKEVENTS=y
CONFIG_GENERIC_CLOCKEVENTS_BROADCAST=y
CONFIG_GENERIC_CLOCKEVENTS_BUILD=y
+CONFIG_GENERIC_CPUFREQ_KRAIT=y
CONFIG_GENERIC_IDLE_POLL_SETUP=y
CONFIG_GENERIC_IO=y
CONFIG_GENERIC_IRQ_SHOW=y
@@ -203,6 +221,10 @@ CONFIG_IRQCHIP=y
CONFIG_IRQ_DOMAIN=y
CONFIG_IRQ_FORCED_THREADING=y
CONFIG_IRQ_WORK=y
+CONFIG_KPSS_XCC=y
+CONFIG_KRAITCC=y
+CONFIG_KRAIT_CLOCKS=y
+CONFIG_KRAIT_L2_ACCESSORS=y
# CONFIG_LEDS_REGULATOR is not set
CONFIG_LIBFDT=y
CONFIG_LOCKUP_DETECTOR=y
@@ -281,6 +303,7 @@ CONFIG_PINCTRL_MSM8X74=y
CONFIG_PM=y
CONFIG_PM_CLK=y
# CONFIG_PM_DEBUG is not set
+CONFIG_PM_OPP=y
CONFIG_PM_SLEEP=y
CONFIG_PM_SLEEP_SMP=y
CONFIG_POWER_RESET=y
@@ -299,6 +322,7 @@ CONFIG_PRINTK_TIME=y
CONFIG_PROC_PAGE_MONITOR=y
CONFIG_QCOM_BAM_DMA=y
CONFIG_QCOM_GSBI=y
+CONFIG_QCOM_HFPLL=y
CONFIG_QCOM_SCM=y
CONFIG_QCOM_WDT=y
CONFIG_RAS=y
diff --git a/target/linux/ipq806x/config-4.0 b/target/linux/ipq806x/config-4.0
index 61535da..3c739e6 100644
--- a/target/linux/ipq806x/config-4.0
+++ b/target/linux/ipq806x/config-4.0
@@ -41,10 +41,12 @@ CONFIG_ARM_ARCH_TIMER_EVTSTREAM=y
CONFIG_ARM_CPU_SUSPEND=y
CONFIG_ARM_GIC=y
CONFIG_ARM_HAS_SG_CHAIN=y
+# CONFIG_ARM_KIRKWOOD_CPUFREQ is not set
CONFIG_ARM_L1_CACHE_SHIFT=6
CONFIG_ARM_L1_CACHE_SHIFT_6=y
# CONFIG_ARM_LPAE is not set
CONFIG_ARM_PATCH_PHYS_VIRT=y
+CONFIG_ARM_QCOM_CPUFREQ=y
# CONFIG_ARM_SMMU is not set
# CONFIG_ARM_SP805_WATCHDOG is not set
CONFIG_ARM_THUMB=y
@@ -66,6 +68,7 @@ CONFIG_COMMON_CLK=y
CONFIG_COMMON_CLK_QCOM=y
CONFIG_COMPACTION=y
CONFIG_COREDUMP=y
+# CONFIG_CPUFREQ_DT is not set
CONFIG_CPU_32v6K=y
CONFIG_CPU_32v7=y
CONFIG_CPU_ABRT_EV7=y
@@ -76,11 +79,25 @@ CONFIG_CPU_CACHE_VIPT=y
CONFIG_CPU_COPY_V6=y
CONFIG_CPU_CP15=y
CONFIG_CPU_CP15_MMU=y
+CONFIG_CPU_FREQ=y
+# CONFIG_CPU_FREQ_DEFAULT_GOV_CONSERVATIVE is not set
+# CONFIG_CPU_FREQ_DEFAULT_GOV_ONDEMAND is not set
+CONFIG_CPU_FREQ_DEFAULT_GOV_PERFORMANCE=y
+# CONFIG_CPU_FREQ_DEFAULT_GOV_POWERSAVE is not set
+# CONFIG_CPU_FREQ_DEFAULT_GOV_USERSPACE is not set
+# CONFIG_CPU_FREQ_GOV_CONSERVATIVE is not set
+# CONFIG_CPU_FREQ_GOV_ONDEMAND is not set
+CONFIG_CPU_FREQ_GOV_PERFORMANCE=y
+# CONFIG_CPU_FREQ_GOV_POWERSAVE is not set
+# CONFIG_CPU_FREQ_GOV_USERSPACE is not set
+CONFIG_CPU_FREQ_STAT=y
+# CONFIG_CPU_FREQ_STAT_DETAILS is not set
CONFIG_CPU_HAS_ASID=y
# CONFIG_CPU_ICACHE_DISABLE is not set
CONFIG_CPU_PABRT_V7=y
CONFIG_CPU_PM=y
CONFIG_CPU_RMAP=y
+# CONFIG_CPU_THERMAL is not set
CONFIG_CPU_TLB_V7=y
CONFIG_CPU_V7=y
CONFIG_CRC16=y
@@ -114,6 +131,7 @@ CONFIG_GENERIC_BUG=y
CONFIG_GENERIC_CLOCKEVENTS=y
CONFIG_GENERIC_CLOCKEVENTS_BROADCAST=y
CONFIG_GENERIC_CLOCKEVENTS_BUILD=y
+CONFIG_GENERIC_CPUFREQ_KRAIT=y
CONFIG_GENERIC_IDLE_POLL_SETUP=y
CONFIG_GENERIC_IO=y
CONFIG_GENERIC_IRQ_SHOW=y
@@ -209,6 +227,10 @@ CONFIG_IRQ_DOMAIN=y
CONFIG_IRQ_DOMAIN_HIERARCHY=y
CONFIG_IRQ_FORCED_THREADING=y
CONFIG_IRQ_WORK=y
+CONFIG_KPSS_XCC=y
+CONFIG_KRAITCC=y
+CONFIG_KRAIT_CLOCKS=y
+CONFIG_KRAIT_L2_ACCESSORS=y
# CONFIG_LEDS_REGULATOR is not set
CONFIG_LIBFDT=y
CONFIG_LOCKUP_DETECTOR=y
@@ -222,6 +244,7 @@ CONFIG_MDIO_BOARDINFO=y
CONFIG_MDIO_GPIO=y
CONFIG_MFD_QCOM_RPM=y
# CONFIG_MFD_SPMI_PMIC is not set
+CONFIG_MFD_SYSCON=y
CONFIG_MIGHT_HAVE_CACHE_L2X0=y
CONFIG_MIGHT_HAVE_PCI=y
CONFIG_MIGRATION=y
@@ -293,6 +316,7 @@ CONFIG_PINCTRL_MSM8X74=y
CONFIG_PM=y
CONFIG_PM_CLK=y
# CONFIG_PM_DEBUG is not set
+CONFIG_PM_OPP=y
CONFIG_PM_SLEEP=y
CONFIG_PM_SLEEP_SMP=y
CONFIG_POWER_RESET=y
@@ -311,6 +335,7 @@ CONFIG_PRINTK_TIME=y
CONFIG_PROC_PAGE_MONITOR=y
CONFIG_QCOM_BAM_DMA=y
CONFIG_QCOM_GSBI=y
+CONFIG_QCOM_HFPLL=y
CONFIG_QCOM_SCM=y
CONFIG_QCOM_WDT=y
CONFIG_RAS=y
diff --git a/target/linux/ipq806x/patches-3.18/130-clk_mux-Fix-set_parent-doing-the-wrong-thing-when-IN.patch b/target/linux/ipq806x/patches-3.18/130-clk_mux-Fix-set_parent-doing-the-wrong-thing-when-IN.patch
new file mode 100644
index 0000000..d943ad5
--- /dev/null
+++ b/target/linux/ipq806x/patches-3.18/130-clk_mux-Fix-set_parent-doing-the-wrong-thing-when-IN.patch
@@ -0,0 +1,60 @@
+From 6793b3cd5da817c4be218bd8632f07cf4d2b0d26 Mon Sep 17 00:00:00 2001
+From: Hans de Goede <hdegoede at redhat.com>
+Date: Wed, 19 Nov 2014 14:48:59 +0100
+Subject: [PATCH] clk_mux: Fix set_parent doing the wrong thing when INDEX_BIT
+ && index >= 3
+
+If CLK_MUX_INDEX_BIT is set, then each bit turns on / off a single parent,
+so theoretically multiple parents could be enabled at the same time, but in
+practice only one bit should ever be 1. So to select parent 0, set
+the register (*) to 0x01, to select parent 1 set it 0x02, parent 2, 0x04,
+parent 3, 0x08, etc.
+
+But the current code does:
+
+ if (mux->flags & CLK_MUX_INDEX_BIT)
+ index = (1 << ffs(index));
+
+Which means that:
+
+For an input index of 0, ffs returns 0, so we set the register
+to 0x01, ok.
+
+For an input index of 1, ffs returns 1, so we set the register
+to 0x02, ok.
+
+For an input index of 2, ffs returns 2, so we set the register
+to 0x04, ok.
+
+For an input index of 3, ffs returns 1, so we set the register
+to 0x02, not good!
+
+The code should simply be:
+
+ if (mux->flags & CLK_MUX_INDEX_BIT)
+ index = 1 << index;
+
+Which always does the right thing, this commit fixes this.
+
+Signed-off-by: Hans de Goede <hdegoede at redhat.com>
+Signed-off-by: Michael Turquette <mturquette at linaro.org>
+---
+ drivers/clk/clk-mux.c | 2 +-
+ 1 file changed, 1 insertion(+), 1 deletion(-)
+
+diff --git a/drivers/clk/clk-mux.c b/drivers/clk/clk-mux.c
+index 4f96ff3..6e1ecf9 100644
+--- a/drivers/clk/clk-mux.c
++++ b/drivers/clk/clk-mux.c
+@@ -77,7 +77,7 @@ static int clk_mux_set_parent(struct clk_hw *hw, u8 index)
+
+ else {
+ if (mux->flags & CLK_MUX_INDEX_BIT)
+- index = (1 << ffs(index));
++ index = 1 << index;
+
+ if (mux->flags & CLK_MUX_INDEX_ONE)
+ index++;
+--
+2.1.4
+
diff --git a/target/linux/ipq806x/patches-3.18/131-clk-Add-__clk_mux_determine_rate_closest.patch b/target/linux/ipq806x/patches-3.18/131-clk-Add-__clk_mux_determine_rate_closest.patch
new file mode 100644
index 0000000..18972f3
--- /dev/null
+++ b/target/linux/ipq806x/patches-3.18/131-clk-Add-__clk_mux_determine_rate_closest.patch
@@ -0,0 +1,120 @@
+From 15a02c1f6dd7c2bb150c61d00ffb33f584ff2288 Mon Sep 17 00:00:00 2001
+From: Stephen Boyd <sboyd at codeaurora.org>
+Date: Mon, 19 Jan 2015 18:05:28 -0800
+Subject: [PATCH] clk: Add __clk_mux_determine_rate_closest
+
+Some clock drivers want to find the closest rate on the input of
+a mux instead of a rate that's less than or equal to the desired
+rate. Add a generic mux function to support this.
+
+Signed-off-by: Stephen Boyd <sboyd at codeaurora.org>
+Tested-by: Kenneth Westfield <kwestfie at codeaurora.org>
+Signed-off-by: Michael Turquette <mturquette at linaro.org>
+---
+ drivers/clk/clk.c | 47 +++++++++++++++++++++++++++++++++++---------
+ include/linux/clk-provider.h | 8 +++++++-
+ 2 files changed, 45 insertions(+), 10 deletions(-)
+
+--- a/drivers/clk/clk.c
++++ b/drivers/clk/clk.c
+@@ -695,14 +695,20 @@ struct clk *__clk_lookup(const char *nam
+ return NULL;
+ }
+
+-/*
+- * Helper for finding best parent to provide a given frequency. This can be used
+- * directly as a determine_rate callback (e.g. for a mux), or from a more
+- * complex clock that may combine a mux with other operations.
+- */
+-long __clk_mux_determine_rate(struct clk_hw *hw, unsigned long rate,
+- unsigned long *best_parent_rate,
+- struct clk **best_parent_p)
++static bool mux_is_better_rate(unsigned long rate, unsigned long now,
++ unsigned long best, unsigned long flags)
++{
++ if (flags & CLK_MUX_ROUND_CLOSEST)
++ return abs(now - rate) < abs(best - rate);
++
++ return now <= rate && now > best;
++}
++
++static long
++clk_mux_determine_rate_flags(struct clk_hw *hw, unsigned long rate,
++ unsigned long *best_parent_rate,
++ struct clk **best_parent_p,
++ unsigned long flags)
+ {
+ struct clk *clk = hw->clk, *parent, *best_parent = NULL;
+ int i, num_parents;
+@@ -730,7 +736,7 @@ long __clk_mux_determine_rate(struct clk
+ parent_rate = __clk_round_rate(parent, rate);
+ else
+ parent_rate = __clk_get_rate(parent);
+- if (parent_rate <= rate && parent_rate > best) {
++ if (mux_is_better_rate(rate, parent_rate, best, flags)) {
+ best_parent = parent;
+ best = parent_rate;
+ }
+@@ -743,8 +749,31 @@ out:
+
+ return best;
+ }
++
++/*
++ * Helper for finding best parent to provide a given frequency. This can be used
++ * directly as a determine_rate callback (e.g. for a mux), or from a more
++ * complex clock that may combine a mux with other operations.
++ */
++long __clk_mux_determine_rate(struct clk_hw *hw, unsigned long rate,
++ unsigned long *best_parent_rate,
++ struct clk **best_parent_p)
++{
++ return clk_mux_determine_rate_flags(hw, rate, best_parent_rate,
++ best_parent_p, 0);
++}
+ EXPORT_SYMBOL_GPL(__clk_mux_determine_rate);
+
++long __clk_mux_determine_rate_closest(struct clk_hw *hw, unsigned long rate,
++ unsigned long *best_parent_rate,
++ struct clk **best_parent_p)
++{
++ return clk_mux_determine_rate_flags(hw, rate, best_parent_rate,
++ best_parent_p,
++ CLK_MUX_ROUND_CLOSEST);
++}
++EXPORT_SYMBOL_GPL(__clk_mux_determine_rate_closest);
++
+ /*** clk api ***/
+
+ void __clk_unprepare(struct clk *clk)
+--- a/include/linux/clk-provider.h
++++ b/include/linux/clk-provider.h
+@@ -382,6 +382,8 @@ struct clk *clk_register_divider_table(s
+ * register, and mask of mux bits are in higher 16-bit of this register.
+ * While setting the mux bits, higher 16-bit should also be updated to
+ * indicate changing mux bits.
++ * CLK_MUX_ROUND_CLOSEST - Use the parent rate that is closest to the desired
++ * frequency.
+ */
+ struct clk_mux {
+ struct clk_hw hw;
+@@ -396,7 +398,8 @@ struct clk_mux {
+ #define CLK_MUX_INDEX_ONE BIT(0)
+ #define CLK_MUX_INDEX_BIT BIT(1)
+ #define CLK_MUX_HIWORD_MASK BIT(2)
+-#define CLK_MUX_READ_ONLY BIT(3) /* mux setting cannot be changed */
++#define CLK_MUX_READ_ONLY BIT(3) /* mux can't be changed */
++#define CLK_MUX_ROUND_CLOSEST BIT(4)
+
+ extern const struct clk_ops clk_mux_ops;
+ extern const struct clk_ops clk_mux_ro_ops;
+@@ -554,6 +557,9 @@ struct clk *__clk_lookup(const char *nam
+ long __clk_mux_determine_rate(struct clk_hw *hw, unsigned long rate,
+ unsigned long *best_parent_rate,
+ struct clk **best_parent_p);
++long __clk_mux_determine_rate_closest(struct clk_hw *hw, unsigned long rate,
++ unsigned long *best_parent_rate,
++ struct clk **best_parent_p);
+
+ /*
+ * FIXME clock api without lock protection
diff --git a/target/linux/ipq806x/patches-3.18/132-clk-Add-clk_unregister_-divider-gate-mux-to-close-me.patch b/target/linux/ipq806x/patches-3.18/132-clk-Add-clk_unregister_-divider-gate-mux-to-close-me.patch
new file mode 100644
index 0000000..127afd2
--- /dev/null
+++ b/target/linux/ipq806x/patches-3.18/132-clk-Add-clk_unregister_-divider-gate-mux-to-close-me.patch
@@ -0,0 +1,115 @@
+From 4e3c021fb995bcbb5d1f814d00584cb80eb904a8 Mon Sep 17 00:00:00 2001
+From: Krzysztof Kozlowski <k.kozlowski at samsung.com>
+Date: Mon, 5 Jan 2015 10:52:40 +0100
+Subject: [PATCH] clk: Add clk_unregister_{divider, gate, mux} to close memory
+ leak
+
+The common clk_register_{divider,gate,mux} functions allocated memory
+for internal data which wasn't freed anywhere. Drivers using these
+helpers could only unregister clocks but the memory would still leak.
+
+Add corresponding unregister functions which will release all resources.
+
+Signed-off-by: Krzysztof Kozlowski <k.kozlowski at samsung.com>
+Reviewed-by: Stephen Boyd <sboyd at codeaurora.org>
+Signed-off-by: Michael Turquette <mturquette at linaro.org>
+---
+ drivers/clk/clk-divider.c | 16 ++++++++++++++++
+ drivers/clk/clk-gate.c | 16 ++++++++++++++++
+ drivers/clk/clk-mux.c | 16 ++++++++++++++++
+ include/linux/clk-provider.h | 4 ++++
+ 4 files changed, 52 insertions(+)
+
+--- a/drivers/clk/clk-divider.c
++++ b/drivers/clk/clk-divider.c
+@@ -463,3 +463,19 @@ struct clk *clk_register_divider_table(s
+ width, clk_divider_flags, table, lock);
+ }
+ EXPORT_SYMBOL_GPL(clk_register_divider_table);
++
++void clk_unregister_divider(struct clk *clk)
++{
++ struct clk_divider *div;
++ struct clk_hw *hw;
++
++ hw = __clk_get_hw(clk);
++ if (!hw)
++ return;
++
++ div = to_clk_divider(hw);
++
++ clk_unregister(clk);
++ kfree(div);
++}
++EXPORT_SYMBOL_GPL(clk_unregister_divider);
+--- a/drivers/clk/clk-gate.c
++++ b/drivers/clk/clk-gate.c
+@@ -162,3 +162,19 @@ struct clk *clk_register_gate(struct dev
+ return clk;
+ }
+ EXPORT_SYMBOL_GPL(clk_register_gate);
++
++void clk_unregister_gate(struct clk *clk)
++{
++ struct clk_gate *gate;
++ struct clk_hw *hw;
++
++ hw = __clk_get_hw(clk);
++ if (!hw)
++ return;
++
++ gate = to_clk_gate(hw);
++
++ clk_unregister(clk);
++ kfree(gate);
++}
++EXPORT_SYMBOL_GPL(clk_unregister_gate);
+--- a/drivers/clk/clk-mux.c
++++ b/drivers/clk/clk-mux.c
+@@ -177,3 +177,19 @@ struct clk *clk_register_mux(struct devi
+ NULL, lock);
+ }
+ EXPORT_SYMBOL_GPL(clk_register_mux);
++
++void clk_unregister_mux(struct clk *clk)
++{
++ struct clk_mux *mux;
++ struct clk_hw *hw;
++
++ hw = __clk_get_hw(clk);
++ if (!hw)
++ return;
++
++ mux = to_clk_mux(hw);
++
++ clk_unregister(clk);
++ kfree(mux);
++}
++EXPORT_SYMBOL_GPL(clk_unregister_mux);
+--- a/include/linux/clk-provider.h
++++ b/include/linux/clk-provider.h
+@@ -294,6 +294,7 @@ struct clk *clk_register_gate(struct dev
+ const char *parent_name, unsigned long flags,
+ void __iomem *reg, u8 bit_idx,
+ u8 clk_gate_flags, spinlock_t *lock);
++void clk_unregister_gate(struct clk *clk);
+
+ struct clk_div_table {
+ unsigned int val;
+@@ -361,6 +362,7 @@ struct clk *clk_register_divider_table(s
+ void __iomem *reg, u8 shift, u8 width,
+ u8 clk_divider_flags, const struct clk_div_table *table,
+ spinlock_t *lock);
++void clk_unregister_divider(struct clk *clk);
+
+ /**
+ * struct clk_mux - multiplexer clock
+@@ -414,6 +416,8 @@ struct clk *clk_register_mux_table(struc
+ void __iomem *reg, u8 shift, u32 mask,
+ u8 clk_mux_flags, u32 *table, spinlock_t *lock);
+
++void clk_unregister_mux(struct clk *clk);
++
+ void of_fixed_factor_clk_setup(struct device_node *node);
+
+ /**
diff --git a/target/linux/ipq806x/patches-3.18/133-ARM-Add-Krait-L2-register-accessor-functions.patch b/target/linux/ipq806x/patches-3.18/133-ARM-Add-Krait-L2-register-accessor-functions.patch
new file mode 100644
index 0000000..36a92c8
--- /dev/null
+++ b/target/linux/ipq806x/patches-3.18/133-ARM-Add-Krait-L2-register-accessor-functions.patch
@@ -0,0 +1,144 @@
+Content-Type: text/plain; charset="utf-8"
+MIME-Version: 1.0
+Content-Transfer-Encoding: 7bit
+Subject: [v3,01/13] ARM: Add Krait L2 register accessor functions
+From: Stephen Boyd <sboyd at codeaurora.org>
+X-Patchwork-Id: 6063051
+Message-Id: <1426920332-9340-2-git-send-email-sboyd at codeaurora.org>
+To: Mike Turquette <mturquette at linaro.org>, Stephen Boyd <sboyd at codeaurora.org>
+Cc: linux-kernel at vger.kernel.org, linux-arm-msm at vger.kernel.org,
+ linux-pm at vger.kernel.org, linux-arm-kernel at lists.infradead.org,
+ Viresh Kumar <viresh.kumar at linaro.org>,
+ Mark Rutland <mark.rutland at arm.com>, Russell King <linux at arm.linux.org.uk>,
+ Courtney Cavin <courtney.cavin at sonymobile.com>
+Date: Fri, 20 Mar 2015 23:45:20 -0700
+
+Krait CPUs have a handful of L2 cache controller registers that
+live behind a cp15 based indirection register. First you program
+the indirection register (l2cpselr) to point the L2 'window'
+register (l2cpdr) at what you want to read/write. Then you
+read/write the 'window' register to do what you want. The
+l2cpselr register is not banked per-cpu so we must lock around
+accesses to it to prevent other CPUs from re-pointing l2cpdr
+underneath us.
+
+Cc: Mark Rutland <mark.rutland at arm.com>
+Cc: Russell King <linux at arm.linux.org.uk>
+Cc: Courtney Cavin <courtney.cavin at sonymobile.com>
+Signed-off-by: Stephen Boyd <sboyd at codeaurora.org>
+
+---
+arch/arm/common/Kconfig | 3 ++
+ arch/arm/common/Makefile | 1 +
+ arch/arm/common/krait-l2-accessors.c | 58 +++++++++++++++++++++++++++++++
+ arch/arm/include/asm/krait-l2-accessors.h | 20 +++++++++++
+ 4 files changed, 82 insertions(+)
+ create mode 100644 arch/arm/common/krait-l2-accessors.c
+ create mode 100644 arch/arm/include/asm/krait-l2-accessors.h
+
+--- a/arch/arm/common/Kconfig
++++ b/arch/arm/common/Kconfig
+@@ -9,6 +9,9 @@ config DMABOUNCE
+ bool
+ select ZONE_DMA
+
++config KRAIT_L2_ACCESSORS
++ bool
++
+ config SHARP_LOCOMO
+ bool
+
+--- a/arch/arm/common/Makefile
++++ b/arch/arm/common/Makefile
+@@ -7,6 +7,7 @@ obj-y += firmware.o
+ obj-$(CONFIG_ICST) += icst.o
+ obj-$(CONFIG_SA1111) += sa1111.o
+ obj-$(CONFIG_DMABOUNCE) += dmabounce.o
++obj-$(CONFIG_KRAIT_L2_ACCESSORS) += krait-l2-accessors.o
+ obj-$(CONFIG_SHARP_LOCOMO) += locomo.o
+ obj-$(CONFIG_SHARP_PARAM) += sharpsl_param.o
+ obj-$(CONFIG_SHARP_SCOOP) += scoop.o
+--- /dev/null
++++ b/arch/arm/common/krait-l2-accessors.c
+@@ -0,0 +1,58 @@
++/*
++ * Copyright (c) 2011-2013, The Linux Foundation. All rights reserved.
++ *
++ * This program is free software; you can redistribute it and/or modify
++ * it under the terms of the GNU General Public License version 2 and
++ * only version 2 as published by the Free Software Foundation.
++ *
++ * This program is distributed in the hope that it will be useful,
++ * but WITHOUT ANY WARRANTY; without even the implied warranty of
++ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
++ * GNU General Public License for more details.
++ */
++
++#include <linux/spinlock.h>
++#include <linux/export.h>
++
++#include <asm/barrier.h>
++#include <asm/krait-l2-accessors.h>
++
++static DEFINE_RAW_SPINLOCK(krait_l2_lock);
++
++void krait_set_l2_indirect_reg(u32 addr, u32 val)
++{
++ unsigned long flags;
++
++ raw_spin_lock_irqsave(&krait_l2_lock, flags);
++ /*
++ * Select the L2 window by poking l2cpselr, then write to the window
++ * via l2cpdr.
++ */
++ asm volatile ("mcr p15, 3, %0, c15, c0, 6 @ l2cpselr" : : "r" (addr));
++ isb();
++ asm volatile ("mcr p15, 3, %0, c15, c0, 7 @ l2cpdr" : : "r" (val));
++ isb();
++
++ raw_spin_unlock_irqrestore(&krait_l2_lock, flags);
++}
++EXPORT_SYMBOL(krait_set_l2_indirect_reg);
++
++u32 krait_get_l2_indirect_reg(u32 addr)
++{
++ u32 val;
++ unsigned long flags;
++
++ raw_spin_lock_irqsave(&krait_l2_lock, flags);
++ /*
++ * Select the L2 window by poking l2cpselr, then read from the window
++ * via l2cpdr.
++ */
++ asm volatile ("mcr p15, 3, %0, c15, c0, 6 @ l2cpselr" : : "r" (addr));
++ isb();
++ asm volatile ("mrc p15, 3, %0, c15, c0, 7 @ l2cpdr" : "=r" (val));
++
++ raw_spin_unlock_irqrestore(&krait_l2_lock, flags);
++
++ return val;
++}
++EXPORT_SYMBOL(krait_get_l2_indirect_reg);
+--- /dev/null
++++ b/arch/arm/include/asm/krait-l2-accessors.h
+@@ -0,0 +1,20 @@
++/*
++ * Copyright (c) 2011-2013, The Linux Foundation. All rights reserved.
++ *
++ * This program is free software; you can redistribute it and/or modify
++ * it under the terms of the GNU General Public License version 2 and
++ * only version 2 as published by the Free Software Foundation.
++ *
++ * This program is distributed in the hope that it will be useful,
++ * but WITHOUT ANY WARRANTY; without even the implied warranty of
++ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
++ * GNU General Public License for more details.
++ */
++
++#ifndef __ASMARM_KRAIT_L2_ACCESSORS_H
++#define __ASMARM_KRAIT_L2_ACCESSORS_H
++
++extern void krait_set_l2_indirect_reg(u32 addr, u32 val);
++extern u32 krait_get_l2_indirect_reg(u32 addr);
++
++#endif
diff --git a/target/linux/ipq806x/patches-3.18/134-clk-mux-Split-out-register-accessors-for-reuse.patch b/target/linux/ipq806x/patches-3.18/134-clk-mux-Split-out-register-accessors-for-reuse.patch
new file mode 100644
index 0000000..50022e6
--- /dev/null
+++ b/target/linux/ipq806x/patches-3.18/134-clk-mux-Split-out-register-accessors-for-reuse.patch
@@ -0,0 +1,192 @@
+Content-Type: text/plain; charset="utf-8"
+MIME-Version: 1.0
+Content-Transfer-Encoding: 7bit
+Subject: [v3,02/13] clk: mux: Split out register accessors for reuse
+From: Stephen Boyd <sboyd at codeaurora.org>
+X-Patchwork-Id: 6063111
+Message-Id: <1426920332-9340-3-git-send-email-sboyd at codeaurora.org>
+To: Mike Turquette <mturquette at linaro.org>, Stephen Boyd <sboyd at codeaurora.org>
+Cc: linux-kernel at vger.kernel.org, linux-arm-msm at vger.kernel.org,
+ linux-pm at vger.kernel.org, linux-arm-kernel at lists.infradead.org,
+ Viresh Kumar <viresh.kumar at linaro.org>
+Date: Fri, 20 Mar 2015 23:45:21 -0700
+
+We want to reuse the logic in clk-mux.c for other clock drivers
+that don't use readl as register accessors. Fortunately, there
+really isn't much to the mux code besides the table indirection
+and quirk flags if you assume any bit shifting and masking has
+been done already. Pull that logic out into reusable functions
+that operate on an optional table and some flags so that other
+drivers can use the same logic.
+
+Signed-off-by: Stephen Boyd <sboyd at codeaurora.org>
+
+---
+drivers/clk/clk-mux.c | 76 +++++++++++++++++++++++++++-----------------
+ include/linux/clk-provider.h | 9 ++++--
+ 2 files changed, 54 insertions(+), 31 deletions(-)
+
+--- a/drivers/clk/clk-mux.c
++++ b/drivers/clk/clk-mux.c
+@@ -29,35 +29,24 @@
+
+ #define to_clk_mux(_hw) container_of(_hw, struct clk_mux, hw)
+
+-static u8 clk_mux_get_parent(struct clk_hw *hw)
++unsigned int clk_mux_get_parent(struct clk_hw *hw, unsigned int val,
++ unsigned int *table, unsigned long flags)
+ {
+- struct clk_mux *mux = to_clk_mux(hw);
+ int num_parents = __clk_get_num_parents(hw->clk);
+- u32 val;
+
+- /*
+- * FIXME need a mux-specific flag to determine if val is bitwise or numeric
+- * e.g. sys_clkin_ck's clksel field is 3 bits wide, but ranges from 0x1
+- * to 0x7 (index starts at one)
+- * OTOH, pmd_trace_clk_mux_ck uses a separate bit for each clock, so
+- * val = 0x4 really means "bit 2, index starts at bit 0"
+- */
+- val = clk_readl(mux->reg) >> mux->shift;
+- val &= mux->mask;
+-
+- if (mux->table) {
++ if (table) {
+ int i;
+
+ for (i = 0; i < num_parents; i++)
+- if (mux->table[i] == val)
++ if (table[i] == val)
+ return i;
+ return -EINVAL;
+ }
+
+- if (val && (mux->flags & CLK_MUX_INDEX_BIT))
++ if (val && (flags & CLK_MUX_INDEX_BIT))
+ val = ffs(val) - 1;
+
+- if (val && (mux->flags & CLK_MUX_INDEX_ONE))
++ if (val && (flags & CLK_MUX_INDEX_ONE))
+ val--;
+
+ if (val >= num_parents)
+@@ -65,24 +54,53 @@ static u8 clk_mux_get_parent(struct clk_
+
+ return val;
+ }
++EXPORT_SYMBOL_GPL(clk_mux_get_parent);
+
+-static int clk_mux_set_parent(struct clk_hw *hw, u8 index)
++static u8 _clk_mux_get_parent(struct clk_hw *hw)
+ {
+ struct clk_mux *mux = to_clk_mux(hw);
+ u32 val;
+- unsigned long flags = 0;
+
+- if (mux->table)
+- index = mux->table[index];
++ /*
++ * FIXME need a mux-specific flag to determine if val is bitwise or numeric
++ * e.g. sys_clkin_ck's clksel field is 3 bits wide, but ranges from 0x1
++ * to 0x7 (index starts at one)
++ * OTOH, pmd_trace_clk_mux_ck uses a separate bit for each clock, so
++ * val = 0x4 really means "bit 2, index starts at bit 0"
++ */
++ val = clk_readl(mux->reg) >> mux->shift;
++ val &= mux->mask;
++
++ return clk_mux_get_parent(hw, val, mux->table, mux->flags);
++}
+
+- else {
+- if (mux->flags & CLK_MUX_INDEX_BIT)
+- index = 1 << index;
++unsigned int clk_mux_reindex(u8 index, unsigned int *table,
++ unsigned long flags)
++{
++ unsigned int val = index;
+
+- if (mux->flags & CLK_MUX_INDEX_ONE)
+- index++;
++ if (table) {
++ val = table[val];
++ } else {
++ if (flags & CLK_MUX_INDEX_BIT)
++ val = 1 << index;
++
++ if (flags & CLK_MUX_INDEX_ONE)
++ val++;
+ }
+
++ return val;
++}
++EXPORT_SYMBOL_GPL(clk_mux_reindex);
++
++static int clk_mux_set_parent(struct clk_hw *hw, u8 index)
++{
++ struct clk_mux *mux = to_clk_mux(hw);
++ u32 val;
++ unsigned long flags = 0;
++
++ index = clk_mux_reindex(index, mux->table, mux->flags);
++
+ if (mux->lock)
+ spin_lock_irqsave(mux->lock, flags);
+
+@@ -102,21 +120,21 @@ static int clk_mux_set_parent(struct clk
+ }
+
+ const struct clk_ops clk_mux_ops = {
+- .get_parent = clk_mux_get_parent,
++ .get_parent = _clk_mux_get_parent,
+ .set_parent = clk_mux_set_parent,
+ .determine_rate = __clk_mux_determine_rate,
+ };
+ EXPORT_SYMBOL_GPL(clk_mux_ops);
+
+ const struct clk_ops clk_mux_ro_ops = {
+- .get_parent = clk_mux_get_parent,
++ .get_parent = _clk_mux_get_parent,
+ };
+ EXPORT_SYMBOL_GPL(clk_mux_ro_ops);
+
+ struct clk *clk_register_mux_table(struct device *dev, const char *name,
+ const char **parent_names, u8 num_parents, unsigned long flags,
+ void __iomem *reg, u8 shift, u32 mask,
+- u8 clk_mux_flags, u32 *table, spinlock_t *lock)
++ u8 clk_mux_flags, unsigned int *table, spinlock_t *lock)
+ {
+ struct clk_mux *mux;
+ struct clk *clk;
+--- a/include/linux/clk-provider.h
++++ b/include/linux/clk-provider.h
+@@ -390,7 +390,7 @@ void clk_unregister_divider(struct clk *
+ struct clk_mux {
+ struct clk_hw hw;
+ void __iomem *reg;
+- u32 *table;
++ unsigned int *table;
+ u32 mask;
+ u8 shift;
+ u8 flags;
+@@ -406,6 +406,11 @@ struct clk_mux {
+ extern const struct clk_ops clk_mux_ops;
+ extern const struct clk_ops clk_mux_ro_ops;
+
++unsigned int clk_mux_get_parent(struct clk_hw *hw, unsigned int val,
++ unsigned int *table, unsigned long flags);
++unsigned int clk_mux_reindex(u8 index, unsigned int *table,
++ unsigned long flags);
++
+ struct clk *clk_register_mux(struct device *dev, const char *name,
+ const char **parent_names, u8 num_parents, unsigned long flags,
+ void __iomem *reg, u8 shift, u8 width,
+@@ -414,7 +419,7 @@ struct clk *clk_register_mux(struct devi
+ struct clk *clk_register_mux_table(struct device *dev, const char *name,
+ const char **parent_names, u8 num_parents, unsigned long flags,
+ void __iomem *reg, u8 shift, u32 mask,
+- u8 clk_mux_flags, u32 *table, spinlock_t *lock);
++ u8 clk_mux_flags, unsigned int *table, spinlock_t *lock);
+
+ void clk_unregister_mux(struct clk *clk);
+
diff --git a/target/linux/ipq806x/patches-3.18/135-clk-Avoid-sending-high-rates-to-downstream-clocks-during-set_rate.patch b/target/linux/ipq806x/patches-3.18/135-clk-Avoid-sending-high-rates-to-downstream-clocks-during-set_rate.patch
new file mode 100644
index 0000000..02d96ad
--- /dev/null
+++ b/target/linux/ipq806x/patches-3.18/135-clk-Avoid-sending-high-rates-to-downstream-clocks-during-set_rate.patch
@@ -0,0 +1,129 @@
+Content-Type: text/plain; charset="utf-8"
+MIME-Version: 1.0
+Content-Transfer-Encoding: 7bit
+Subject: [v3, 03/13] clk: Avoid sending high rates to downstream clocks during
+ set_rate
+From: Stephen Boyd <sboyd at codeaurora.org>
+X-Patchwork-Id: 6063271
+Message-Id: <1426920332-9340-4-git-send-email-sboyd at codeaurora.org>
+To: Mike Turquette <mturquette at linaro.org>, Stephen Boyd <sboyd at codeaurora.org>
+Cc: linux-kernel at vger.kernel.org, linux-arm-msm at vger.kernel.org,
+ linux-pm at vger.kernel.org, linux-arm-kernel at lists.infradead.org,
+ Viresh Kumar <viresh.kumar at linaro.org>
+Date: Fri, 20 Mar 2015 23:45:22 -0700
+
+If a clock is on and we call clk_set_rate() on it we may get into
+a situation where the clock temporarily increases in rate
+dramatically while we walk the tree and call .set_rate() ops. For
+example, consider a case where a PLL feeds into a divider.
+Initially the divider is set to divide by 1 and the PLL is
+running fairly slow (100MHz). The downstream consumer of the
+divider output can only handle rates =< 400 MHz, but the divider
+can only choose between divisors of 1 and 4.
+
+ +-----+ +----------------+
+ | PLL |-->| div 1 or div 4 |---> consumer device
+ +-----+ +----------------+
+
+To achieve a rate of 400MHz on the output of the divider, we
+would have to set the rate of the PLL to 1.6 GHz and then divide
+it by 4. The current code would set the PLL to 1.6GHz first while
+the divider is still set to 1, thus causing the downstream
+consumer of the clock to receive a few clock cycles of 1.6GHz
+clock (far beyond it's maximum acceptable rate). We should be
+changing the divider first before increasing the PLL rate to
+avoid this problem.
+
+Therefore, set the rate of any child clocks that are increasing
+in rate from their current rate so that they can increase their
+dividers if necessary. We assume that there isn't such a thing as
+minimum rate requirements.
+
+Signed-off-by: Stephen Boyd <sboyd at codeaurora.org>
+
+---
+drivers/clk/clk.c | 34 ++++++++++++++++++++++------------
+ 1 file changed, 22 insertions(+), 12 deletions(-)
+
+--- a/drivers/clk/clk.c
++++ b/drivers/clk/clk.c
+@@ -1476,21 +1476,23 @@ static struct clk *clk_propagate_rate_ch
+ * walk down a subtree and set the new rates notifying the rate
+ * change on the way
+ */
+-static void clk_change_rate(struct clk *clk)
++static void clk_change_rate(struct clk *clk, unsigned long best_parent_rate)
+ {
+ struct clk *child;
+ struct hlist_node *tmp;
+ unsigned long old_rate;
+- unsigned long best_parent_rate = 0;
+ bool skip_set_rate = false;
+ struct clk *old_parent;
+
+- old_rate = clk->rate;
++ hlist_for_each_entry(child, &clk->children, child_node) {
++ /* Skip children who will be reparented to another clock */
++ if (child->new_parent && child->new_parent != clk)
++ continue;
++ if (child->new_rate > child->rate)
++ clk_change_rate(child, clk->new_rate);
++ }
+
+- if (clk->new_parent)
+- best_parent_rate = clk->new_parent->rate;
+- else if (clk->parent)
+- best_parent_rate = clk->parent->rate;
++ old_rate = clk->rate;
+
+ if (clk->new_parent && clk->new_parent != clk->parent) {
+ old_parent = __clk_set_parent_before(clk, clk->new_parent);
+@@ -1510,7 +1512,7 @@ static void clk_change_rate(struct clk *
+ if (!skip_set_rate && clk->ops->set_rate)
+ clk->ops->set_rate(clk->hw, clk->new_rate, best_parent_rate);
+
+- clk->rate = clk_recalc(clk, best_parent_rate);
++ clk->rate = clk->new_rate;
+
+ if (clk->notifier_count && old_rate != clk->rate)
+ __clk_notify(clk, POST_RATE_CHANGE, old_rate, clk->rate);
+@@ -1523,12 +1525,13 @@ static void clk_change_rate(struct clk *
+ /* Skip children who will be reparented to another clock */
+ if (child->new_parent && child->new_parent != clk)
+ continue;
+- clk_change_rate(child);
++ if (child->new_rate != child->rate)
++ clk_change_rate(child, clk->new_rate);
+ }
+
+ /* handle the new child who might not be in clk->children yet */
+- if (clk->new_child)
+- clk_change_rate(clk->new_child);
++ if (clk->new_child && clk->new_child->new_rate != clk->new_child->rate)
++ clk_change_rate(clk->new_child, clk->new_rate);
+ }
+
+ /**
+@@ -1556,6 +1559,7 @@ int clk_set_rate(struct clk *clk, unsign
+ {
+ struct clk *top, *fail_clk;
+ int ret = 0;
++ unsigned long parent_rate;
+
+ if (!clk)
+ return 0;
+@@ -1589,8 +1593,13 @@ int clk_set_rate(struct clk *clk, unsign
+ goto out;
+ }
+
++ if (top->parent)
++ parent_rate = top->parent->rate;
++ else
++ parent_rate = 0;
++
+ /* change the rates */
+- clk_change_rate(top);
++ clk_change_rate(top, parent_rate);
+
+ out:
+ clk_prepare_unlock();
diff --git a/target/linux/ipq806x/patches-3.18/136-clk-Add-safe-switch-hook.patch b/target/linux/ipq806x/patches-3.18/136-clk-Add-safe-switch-hook.patch
new file mode 100644
index 0000000..227f8ce
--- /dev/null
+++ b/target/linux/ipq806x/patches-3.18/136-clk-Add-safe-switch-hook.patch
@@ -0,0 +1,170 @@
+Content-Type: text/plain; charset="utf-8"
+MIME-Version: 1.0
+Content-Transfer-Encoding: 7bit
+Subject: [v3,04/13] clk: Add safe switch hook
+From: Stephen Boyd <sboyd at codeaurora.org>
+X-Patchwork-Id: 6063211
+Message-Id: <1426920332-9340-5-git-send-email-sboyd at codeaurora.org>
+To: Mike Turquette <mturquette at linaro.org>, Stephen Boyd <sboyd at codeaurora.org>
+Cc: linux-kernel at vger.kernel.org, linux-arm-msm at vger.kernel.org,
+ linux-pm at vger.kernel.org, linux-arm-kernel at lists.infradead.org,
+ Viresh Kumar <viresh.kumar at linaro.org>
+Date: Fri, 20 Mar 2015 23:45:23 -0700
+
+Sometimes clocks can't accept their parent source turning off
+while the source is reprogrammed to a different rate. Most
+notably CPU clocks require a way to switch away from the current
+PLL they're running on, reprogram that PLL to a new rate, and
+then switch back to the PLL with the new rate once they're done.
+Add a hook that drivers can implement allowing them to return a
+'safe parent' that they can switch their parent to while the
+upstream source is reprogrammed to support this.
+
+Signed-off-by: Stephen Boyd <sboyd at codeaurora.org>
+
+---
+This patch is good enough for Krait, but soon I'll need to
+support a "safe rate" where we ask a clock what rate it needs to be running
+at to be sure it's within voltage constraints. Right now safe parent
+handles that problem on Krait, but on other platforms it won't work.
+
+ drivers/clk/clk.c | 61 ++++++++++++++++++++++++++++++++++++++------
+ include/linux/clk-provider.h | 1 +
+ 2 files changed, 54 insertions(+), 8 deletions(-)
+
+--- a/drivers/clk/clk.c
++++ b/drivers/clk/clk.c
+@@ -1350,7 +1350,8 @@ out:
+ static void clk_calc_subtree(struct clk *clk, unsigned long new_rate,
+ struct clk *new_parent, u8 p_index)
+ {
+- struct clk *child;
++ struct clk *child, *parent;
++ struct clk_hw *parent_hw;
+
+ clk->new_rate = new_rate;
+ clk->new_parent = new_parent;
+@@ -1360,6 +1361,18 @@ static void clk_calc_subtree(struct clk
+ if (new_parent && new_parent != clk->parent)
+ new_parent->new_child = clk;
+
++ if (clk->ops->get_safe_parent) {
++ parent_hw = clk->ops->get_safe_parent(clk->hw);
++ if (parent_hw) {
++ parent = parent_hw->clk;
++ p_index = clk_fetch_parent_index(clk, parent);
++ clk->safe_parent_index = p_index;
++ clk->safe_parent = parent;
++ }
++ } else {
++ clk->safe_parent = NULL;
++ }
++
+ hlist_for_each_entry(child, &clk->children, child_node) {
+ child->new_rate = clk_recalc(child, new_rate);
+ clk_calc_subtree(child, child->new_rate, NULL, 0);
+@@ -1439,17 +1452,47 @@ out:
+ * so that in case of an error we can walk down the whole tree again and
+ * abort the change.
+ */
+-static struct clk *clk_propagate_rate_change(struct clk *clk, unsigned long event)
++static struct clk *clk_propagate_rate_change(struct clk *clk,
++ unsigned long event)
+ {
+ struct clk *child, *tmp_clk, *fail_clk = NULL;
++ struct clk *old_parent;
+ int ret = NOTIFY_DONE;
+
+- if (clk->rate == clk->new_rate)
++ if (clk->rate == clk->new_rate && event != POST_RATE_CHANGE)
+ return NULL;
+
++ switch (event) {
++ case PRE_RATE_CHANGE:
++ if (clk->safe_parent)
++ clk->ops->set_parent(clk->hw, clk->safe_parent_index);
++ clk->old_rate = clk->rate;
++ break;
++ case POST_RATE_CHANGE:
++ if (clk->safe_parent) {
++ old_parent = __clk_set_parent_before(clk,
++ clk->new_parent);
++ if (clk->ops->set_rate_and_parent) {
++ clk->ops->set_rate_and_parent(clk->hw,
++ clk->new_rate,
++ clk->new_parent ?
++ clk->new_parent->rate : 0,
++ clk->new_parent_index);
++ } else if (clk->ops->set_parent) {
++ clk->ops->set_parent(clk->hw,
++ clk->new_parent_index);
++ }
++ __clk_set_parent_after(clk, clk->new_parent,
++ old_parent);
++ }
++ break;
++ }
++
+ if (clk->notifier_count) {
+- ret = __clk_notify(clk, event, clk->rate, clk->new_rate);
+- if (ret & NOTIFY_STOP_MASK)
++ if (event != POST_RATE_CHANGE || clk->old_rate != clk->rate)
++ ret = __clk_notify(clk, event, clk->old_rate,
++ clk->new_rate);
++ if (ret & NOTIFY_STOP_MASK && event != POST_RATE_CHANGE)
+ fail_clk = clk;
+ }
+
+@@ -1494,7 +1537,8 @@ static void clk_change_rate(struct clk *
+
+ old_rate = clk->rate;
+
+- if (clk->new_parent && clk->new_parent != clk->parent) {
++ if (clk->new_parent && clk->new_parent != clk->parent &&
++ !clk->safe_parent) {
+ old_parent = __clk_set_parent_before(clk, clk->new_parent);
+
+ if (clk->ops->set_rate_and_parent) {
+@@ -1514,9 +1558,6 @@ static void clk_change_rate(struct clk *
+
+ clk->rate = clk->new_rate;
+
+- if (clk->notifier_count && old_rate != clk->rate)
+- __clk_notify(clk, POST_RATE_CHANGE, old_rate, clk->rate);
+-
+ /*
+ * Use safe iteration, as change_rate can actually swap parents
+ * for certain clock types.
+@@ -1601,6 +1642,8 @@ int clk_set_rate(struct clk *clk, unsign
+ /* change the rates */
+ clk_change_rate(top, parent_rate);
+
++ clk_propagate_rate_change(top, POST_RATE_CHANGE);
++
+ out:
+ clk_prepare_unlock();
+
+--- a/include/linux/clk-provider.h
++++ b/include/linux/clk-provider.h
+@@ -179,6 +179,7 @@ struct clk_ops {
+ struct clk **best_parent_clk);
+ int (*set_parent)(struct clk_hw *hw, u8 index);
+ u8 (*get_parent)(struct clk_hw *hw);
++ struct clk_hw *(*get_safe_parent)(struct clk_hw *hw);
+ int (*set_rate)(struct clk_hw *hw, unsigned long rate,
+ unsigned long parent_rate);
+ int (*set_rate_and_parent)(struct clk_hw *hw,
+--- a/include/linux/clk-private.h
++++ b/include/linux/clk-private.h
+@@ -38,8 +38,11 @@ struct clk {
+ struct clk **parents;
+ u8 num_parents;
+ u8 new_parent_index;
++ u8 safe_parent_index;
+ unsigned long rate;
++ unsigned long old_rate;
+ unsigned long new_rate;
++ struct clk *safe_parent;
+ struct clk *new_parent;
+ struct clk *new_child;
+ unsigned long flags;
diff --git a/target/linux/ipq806x/patches-3.18/137-clk-qcom-Add-support-for-High-Frequency-PLLs-HFPLLs.patch b/target/linux/ipq806x/patches-3.18/137-clk-qcom-Add-support-for-High-Frequency-PLLs-HFPLLs.patch
new file mode 100644
index 0000000..701d5e7
--- /dev/null
+++ b/target/linux/ipq806x/patches-3.18/137-clk-qcom-Add-support-for-High-Frequency-PLLs-HFPLLs.patch
@@ -0,0 +1,351 @@
+Content-Type: text/plain; charset="utf-8"
+MIME-Version: 1.0
+Content-Transfer-Encoding: 7bit
+Subject: [v3,05/13] clk: qcom: Add support for High-Frequency PLLs (HFPLLs)
+From: Stephen Boyd <sboyd at codeaurora.org>
+X-Patchwork-Id: 6063261
+Message-Id: <1426920332-9340-6-git-send-email-sboyd at codeaurora.org>
+To: Mike Turquette <mturquette at linaro.org>, Stephen Boyd <sboyd at codeaurora.org>
+Cc: linux-kernel at vger.kernel.org, linux-arm-msm at vger.kernel.org,
+ linux-pm at vger.kernel.org, linux-arm-kernel at lists.infradead.org,
+ Viresh Kumar <viresh.kumar at linaro.org>
+Date: Fri, 20 Mar 2015 23:45:24 -0700
+
+HFPLLs are the main frequency source for Krait CPU clocks. Add
+support for changing the rate of these PLLs.
+
+Signed-off-by: Stephen Boyd <sboyd at codeaurora.org>
+
+---
+I'd really like to get rid of __clk_hfpll_init_once() if possible...
+
+ drivers/clk/qcom/Makefile | 1 +
+ drivers/clk/qcom/clk-hfpll.c | 253 +++++++++++++++++++++++++++++++++++++++++++
+ drivers/clk/qcom/clk-hfpll.h | 54 +++++++++
+ 3 files changed, 308 insertions(+)
+ create mode 100644 drivers/clk/qcom/clk-hfpll.c
+ create mode 100644 drivers/clk/qcom/clk-hfpll.h
+
+--- a/drivers/clk/qcom/Makefile
++++ b/drivers/clk/qcom/Makefile
+@@ -6,6 +6,7 @@ clk-qcom-y += clk-pll.o
+ clk-qcom-y += clk-rcg.o
+ clk-qcom-y += clk-rcg2.o
+ clk-qcom-y += clk-branch.o
++clk-qcom-y += clk-hfpll.o
+ clk-qcom-y += reset.o
+
+ obj-$(CONFIG_APQ_GCC_8084) += gcc-apq8084.o
+--- /dev/null
++++ b/drivers/clk/qcom/clk-hfpll.c
+@@ -0,0 +1,253 @@
++/*
++ * Copyright (c) 2013-2014, The Linux Foundation. All rights reserved.
++ *
++ * This program is free software; you can redistribute it and/or modify
++ * it under the terms of the GNU General Public License version 2 and
++ * only version 2 as published by the Free Software Foundation.
++ *
++ * This program is distributed in the hope that it will be useful,
++ * but WITHOUT ANY WARRANTY; without even the implied warranty of
++ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
++ * GNU General Public License for more details.
++ */
++#include <linux/kernel.h>
++#include <linux/export.h>
++#include <linux/regmap.h>
++#include <linux/delay.h>
++#include <linux/err.h>
++#include <linux/clk-provider.h>
++#include <linux/spinlock.h>
++
++#include "clk-regmap.h"
++#include "clk-hfpll.h"
++
++#define PLL_OUTCTRL BIT(0)
++#define PLL_BYPASSNL BIT(1)
++#define PLL_RESET_N BIT(2)
++
++/* Initialize a HFPLL at a given rate and enable it. */
++static void __clk_hfpll_init_once(struct clk_hw *hw)
++{
++ struct clk_hfpll *h = to_clk_hfpll(hw);
++ struct hfpll_data const *hd = h->d;
++ struct regmap *regmap = h->clkr.regmap;
++
++ if (likely(h->init_done))
++ return;
++
++ /* Configure PLL parameters for integer mode. */
++ if (hd->config_val)
++ regmap_write(regmap, hd->config_reg, hd->config_val);
++ regmap_write(regmap, hd->m_reg, 0);
++ regmap_write(regmap, hd->n_reg, 1);
++
++ if (hd->user_reg) {
++ u32 regval = hd->user_val;
++ unsigned long rate;
++
++ rate = __clk_get_rate(hw->clk);
++
++ /* Pick the right VCO. */
++ if (hd->user_vco_mask && rate > hd->low_vco_max_rate)
++ regval |= hd->user_vco_mask;
++ regmap_write(regmap, hd->user_reg, regval);
++ }
++
++ if (hd->droop_reg)
++ regmap_write(regmap, hd->droop_reg, hd->droop_val);
++
++ h->init_done = true;
++}
++
++static void __clk_hfpll_enable(struct clk_hw *hw)
++{
++ struct clk_hfpll *h = to_clk_hfpll(hw);
++ struct hfpll_data const *hd = h->d;
++ struct regmap *regmap = h->clkr.regmap;
++ u32 val;
++
++ __clk_hfpll_init_once(hw);
++
++ /* Disable PLL bypass mode. */
++ regmap_update_bits(regmap, hd->mode_reg, PLL_BYPASSNL, PLL_BYPASSNL);
++
++ /*
++ * H/W requires a 5us delay between disabling the bypass and
++ * de-asserting the reset. Delay 10us just to be safe.
++ */
++ udelay(10);
++
++ /* De-assert active-low PLL reset. */
++ regmap_update_bits(regmap, hd->mode_reg, PLL_RESET_N, PLL_RESET_N);
++
++ /* Wait for PLL to lock. */
++ if (hd->status_reg) {
++ do {
++ regmap_read(regmap, hd->status_reg, &val);
++ } while (!(val & BIT(hd->lock_bit)));
++ } else {
++ udelay(60);
++ }
++
++ /* Enable PLL output. */
++ regmap_update_bits(regmap, hd->mode_reg, PLL_OUTCTRL, PLL_OUTCTRL);
++}
++
++/* Enable an already-configured HFPLL. */
++static int clk_hfpll_enable(struct clk_hw *hw)
++{
++ unsigned long flags;
++ struct clk_hfpll *h = to_clk_hfpll(hw);
++ struct hfpll_data const *hd = h->d;
++ struct regmap *regmap = h->clkr.regmap;
++ u32 mode;
++
++ spin_lock_irqsave(&h->lock, flags);
++ regmap_read(regmap, hd->mode_reg, &mode);
++ if (!(mode & (PLL_BYPASSNL | PLL_RESET_N | PLL_OUTCTRL)))
++ __clk_hfpll_enable(hw);
++ spin_unlock_irqrestore(&h->lock, flags);
++
++ return 0;
++}
++
++static void __clk_hfpll_disable(struct clk_hfpll *h)
++{
++ struct hfpll_data const *hd = h->d;
++ struct regmap *regmap = h->clkr.regmap;
++
++ /*
++ * Disable the PLL output, disable test mode, enable the bypass mode,
++ * and assert the reset.
++ */
++ regmap_update_bits(regmap, hd->mode_reg,
++ PLL_BYPASSNL | PLL_RESET_N | PLL_OUTCTRL, 0);
++}
++
++static void clk_hfpll_disable(struct clk_hw *hw)
++{
++ struct clk_hfpll *h = to_clk_hfpll(hw);
++ unsigned long flags;
++
++ spin_lock_irqsave(&h->lock, flags);
++ __clk_hfpll_disable(h);
++ spin_unlock_irqrestore(&h->lock, flags);
++}
++
++static long clk_hfpll_round_rate(struct clk_hw *hw, unsigned long rate,
++ unsigned long *parent_rate)
++{
++ struct clk_hfpll *h = to_clk_hfpll(hw);
++ struct hfpll_data const *hd = h->d;
++ unsigned long rrate;
++
++ rate = clamp(rate, hd->min_rate, hd->max_rate);
++
++ rrate = DIV_ROUND_UP(rate, *parent_rate) * *parent_rate;
++ if (rrate > hd->max_rate)
++ rrate -= *parent_rate;
++
++ return rrate;
++}
++
++/*
++ * For optimization reasons, assumes no downstream clocks are actively using
++ * it.
++ */
++static int clk_hfpll_set_rate(struct clk_hw *hw, unsigned long rate,
++ unsigned long parent_rate)
++{
++ struct clk_hfpll *h = to_clk_hfpll(hw);
++ struct hfpll_data const *hd = h->d;
++ struct regmap *regmap = h->clkr.regmap;
++ unsigned long flags;
++ u32 l_val, val;
++ bool enabled;
++
++ l_val = rate / parent_rate;
++
++ spin_lock_irqsave(&h->lock, flags);
++
++ enabled = __clk_is_enabled(hw->clk);
++ if (enabled)
++ __clk_hfpll_disable(h);
++
++ /* Pick the right VCO. */
++ if (hd->user_reg && hd->user_vco_mask) {
++ regmap_read(regmap, hd->user_reg, &val);
++ if (rate <= hd->low_vco_max_rate)
++ val &= ~hd->user_vco_mask;
++ else
++ val |= hd->user_vco_mask;
++ regmap_write(regmap, hd->user_reg, val);
++ }
++
++ regmap_write(regmap, hd->l_reg, l_val);
++
++ if (enabled)
++ __clk_hfpll_enable(hw);
++
++ spin_unlock_irqrestore(&h->lock, flags);
++
++ return 0;
++}
++
++static unsigned long clk_hfpll_recalc_rate(struct clk_hw *hw,
++ unsigned long parent_rate)
++{
++ struct clk_hfpll *h = to_clk_hfpll(hw);
++ struct hfpll_data const *hd = h->d;
++ struct regmap *regmap = h->clkr.regmap;
++ u32 l_val;
++
++ regmap_read(regmap, hd->l_reg, &l_val);
++
++ return l_val * parent_rate;
++}
++
++static void clk_hfpll_init(struct clk_hw *hw)
++{
++ struct clk_hfpll *h = to_clk_hfpll(hw);
++ struct hfpll_data const *hd = h->d;
++ struct regmap *regmap = h->clkr.regmap;
++ u32 mode, status;
++
++ regmap_read(regmap, hd->mode_reg, &mode);
++ if (mode != (PLL_BYPASSNL | PLL_RESET_N | PLL_OUTCTRL)) {
++ __clk_hfpll_init_once(hw);
++ return;
++ }
++
++ if (hd->status_reg) {
++ regmap_read(regmap, hd->status_reg, &status);
++ if (!(status & BIT(hd->lock_bit))) {
++ WARN(1, "HFPLL %s is ON, but not locked!\n",
++ __clk_get_name(hw->clk));
++ clk_hfpll_disable(hw);
++ __clk_hfpll_init_once(hw);
++ }
++ }
++}
++
++static int hfpll_is_enabled(struct clk_hw *hw)
++{
++ struct clk_hfpll *h = to_clk_hfpll(hw);
++ struct hfpll_data const *hd = h->d;
++ struct regmap *regmap = h->clkr.regmap;
++ u32 mode;
++
++ regmap_read(regmap, hd->mode_reg, &mode);
++ mode &= 0x7;
++ return mode == (PLL_BYPASSNL | PLL_RESET_N | PLL_OUTCTRL);
++}
++
++const struct clk_ops clk_ops_hfpll = {
++ .enable = clk_hfpll_enable,
++ .disable = clk_hfpll_disable,
++ .is_enabled = hfpll_is_enabled,
++ .round_rate = clk_hfpll_round_rate,
++ .set_rate = clk_hfpll_set_rate,
++ .recalc_rate = clk_hfpll_recalc_rate,
++ .init = clk_hfpll_init,
++};
++EXPORT_SYMBOL_GPL(clk_ops_hfpll);
+--- /dev/null
++++ b/drivers/clk/qcom/clk-hfpll.h
+@@ -0,0 +1,54 @@
++/*
++ * Copyright (c) 2013-2014, The Linux Foundation. All rights reserved.
++ *
++ * This program is free software; you can redistribute it and/or modify
++ * it under the terms of the GNU General Public License version 2 and
++ * only version 2 as published by the Free Software Foundation.
++ *
++ * This program is distributed in the hope that it will be useful,
++ * but WITHOUT ANY WARRANTY; without even the implied warranty of
++ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
++ * GNU General Public License for more details.
++ */
++#ifndef __QCOM_CLK_HFPLL_H__
++#define __QCOM_CLK_HFPLL_H__
++
++#include <linux/clk-provider.h>
++#include <linux/spinlock.h>
++#include "clk-regmap.h"
++
++struct hfpll_data {
++ u32 mode_reg;
++ u32 l_reg;
++ u32 m_reg;
++ u32 n_reg;
++ u32 user_reg;
++ u32 droop_reg;
++ u32 config_reg;
++ u32 status_reg;
++ u8 lock_bit;
++
++ u32 droop_val;
++ u32 config_val;
++ u32 user_val;
++ u32 user_vco_mask;
++ unsigned long low_vco_max_rate;
++
++ unsigned long min_rate;
++ unsigned long max_rate;
++};
++
++struct clk_hfpll {
++ struct hfpll_data const *d;
++ int init_done;
++
++ struct clk_regmap clkr;
++ spinlock_t lock;
++};
++
++#define to_clk_hfpll(_hw) \
++ container_of(to_clk_regmap(_hw), struct clk_hfpll, clkr)
++
++extern const struct clk_ops clk_ops_hfpll;
++
++#endif
diff --git a/target/linux/ipq806x/patches-3.18/138-clk-qcom-Add-HFPLL-driver.patch b/target/linux/ipq806x/patches-3.18/138-clk-qcom-Add-HFPLL-driver.patch
new file mode 100644
index 0000000..a0b1d64
--- /dev/null
+++ b/target/linux/ipq806x/patches-3.18/138-clk-qcom-Add-HFPLL-driver.patch
@@ -0,0 +1,206 @@
+Content-Type: text/plain; charset="utf-8"
+MIME-Version: 1.0
+Content-Transfer-Encoding: 7bit
+Subject: [v3,06/13] clk: qcom: Add HFPLL driver
+From: Stephen Boyd <sboyd at codeaurora.org>
+X-Patchwork-Id: 6063231
+Message-Id: <1426920332-9340-7-git-send-email-sboyd at codeaurora.org>
+To: Mike Turquette <mturquette at linaro.org>, Stephen Boyd <sboyd at codeaurora.org>
+Cc: linux-kernel at vger.kernel.org, linux-arm-msm at vger.kernel.org,
+ linux-pm at vger.kernel.org, linux-arm-kernel at lists.infradead.org,
+ Viresh Kumar <viresh.kumar at linaro.org>, <devicetree at vger.kernel.org>
+Date: Fri, 20 Mar 2015 23:45:25 -0700
+
+On some devices (MSM8974 for example), the HFPLLs are
+instantiated within the Krait processor subsystem as separate
+register regions. Add a driver for these PLLs so that we can
+provide HFPLL clocks for use by the system.
+
+Cc: <devicetree at vger.kernel.org>
+Signed-off-by: Stephen Boyd <sboyd at codeaurora.org>
+
+---
+.../devicetree/bindings/clock/qcom,hfpll.txt | 40 ++++++++
+ drivers/clk/qcom/Kconfig | 8 ++
+ drivers/clk/qcom/Makefile | 1 +
+ drivers/clk/qcom/hfpll.c | 109 +++++++++++++++++++++
+ 4 files changed, 158 insertions(+)
+ create mode 100644 Documentation/devicetree/bindings/clock/qcom,hfpll.txt
+ create mode 100644 drivers/clk/qcom/hfpll.c
+
+--- /dev/null
++++ b/Documentation/devicetree/bindings/clock/qcom,hfpll.txt
+@@ -0,0 +1,40 @@
++High-Frequency PLL (HFPLL)
++
++PROPERTIES
++
++- compatible:
++ Usage: required
++ Value type: <string>
++ Definition: must be "qcom,hfpll"
++
++- reg:
++ Usage: required
++ Value type: <prop-encoded-array>
++ Definition: address and size of HPLL registers. An optional second
++ element specifies the address and size of the alias
++ register region.
++
++- clock-output-names:
++ Usage: required
++ Value type: <string>
++ Definition: Name of the PLL. Typically hfpllX where X is a CPU number
++ starting at 0. Otherwise hfpll_Y where Y is more specific
++ such as "l2".
++
++Example:
++
++1) An HFPLL for the L2 cache.
++
++ clock-controller at f9016000 {
++ compatible = "qcom,hfpll";
++ reg = <0xf9016000 0x30>;
++ clock-output-names = "hfpll_l2";
++ };
++
++2) An HFPLL for CPU0. This HFPLL has the alias register region.
++
++ clock-controller at f908a000 {
++ compatible = "qcom,hfpll";
++ reg = <0xf908a000 0x30>, <0xf900a000 0x30>;
++ clock-output-names = "hfpll0";
++ };
+--- a/drivers/clk/qcom/Kconfig
++++ b/drivers/clk/qcom/Kconfig
+@@ -70,3 +70,11 @@ config MSM_MMCC_8974
+ Support for the multimedia clock controller on msm8974 devices.
+ Say Y if you want to support multimedia devices such as display,
+ graphics, video encode/decode, camera, etc.
++
++config QCOM_HFPLL
++ tristate "High-Frequency PLL (HFPLL) Clock Controller"
++ depends on COMMON_CLK_QCOM
++ help
++ Support for the high-frequency PLLs present on Qualcomm devices.
++ Say Y if you want to support CPU frequency scaling on devices
++ such as MSM8974, APQ8084, etc.
+--- a/drivers/clk/qcom/Makefile
++++ b/drivers/clk/qcom/Makefile
+@@ -17,3 +17,4 @@ obj-$(CONFIG_MSM_GCC_8960) += gcc-msm896
+ obj-$(CONFIG_MSM_GCC_8974) += gcc-msm8974.o
+ obj-$(CONFIG_MSM_MMCC_8960) += mmcc-msm8960.o
+ obj-$(CONFIG_MSM_MMCC_8974) += mmcc-msm8974.o
++obj-$(CONFIG_QCOM_HFPLL) += hfpll.o
+--- /dev/null
++++ b/drivers/clk/qcom/hfpll.c
+@@ -0,0 +1,109 @@
++/*
++ * Copyright (c) 2013-2014, The Linux Foundation. All rights reserved.
++ *
++ * This program is free software; you can redistribute it and/or modify
++ * it under the terms of the GNU General Public License version 2 and
++ * only version 2 as published by the Free Software Foundation.
++ *
++ * This program is distributed in the hope that it will be useful,
++ * but WITHOUT ANY WARRANTY; without even the implied warranty of
++ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
++ * GNU General Public License for more details.
++ */
++
++#include <linux/kernel.h>
++#include <linux/init.h>
++#include <linux/module.h>
++#include <linux/platform_device.h>
++#include <linux/of.h>
++#include <linux/clk.h>
++#include <linux/clk-provider.h>
++#include <linux/regmap.h>
++
++#include "clk-regmap.h"
++#include "clk-hfpll.h"
++
++static const struct hfpll_data hdata = {
++ .mode_reg = 0x00,
++ .l_reg = 0x04,
++ .m_reg = 0x08,
++ .n_reg = 0x0c,
++ .user_reg = 0x10,
++ .config_reg = 0x14,
++ .config_val = 0x430405d,
++ .status_reg = 0x1c,
++ .lock_bit = 16,
++
++ .user_val = 0x8,
++ .user_vco_mask = 0x100000,
++ .low_vco_max_rate = 1248000000,
++ .min_rate = 537600000UL,
++ .max_rate = 2900000000UL,
++};
++
++static const struct of_device_id qcom_hfpll_match_table[] = {
++ { .compatible = "qcom,hfpll" },
++ { }
++};
++MODULE_DEVICE_TABLE(of, qcom_hfpll_match_table);
++
++static const struct regmap_config hfpll_regmap_config = {
++ .reg_bits = 32,
++ .reg_stride = 4,
++ .val_bits = 32,
++ .max_register = 0x30,
++ .fast_io = true,
++};
++
++static int qcom_hfpll_probe(struct platform_device *pdev)
++{
++ struct clk *clk;
++ struct resource *res;
++ struct device *dev = &pdev->dev;
++ void __iomem *base;
++ struct regmap *regmap;
++ struct clk_hfpll *h;
++ struct clk_init_data init = {
++ .parent_names = (const char *[]){ "xo" },
++ .num_parents = 1,
++ .ops = &clk_ops_hfpll,
++ };
++
++ h = devm_kzalloc(dev, sizeof(*h), GFP_KERNEL);
++ if (!h)
++ return -ENOMEM;
++
++ res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
++ base = devm_ioremap_resource(dev, res);
++ if (IS_ERR(base))
++ return PTR_ERR(base);
++
++ regmap = devm_regmap_init_mmio(&pdev->dev, base, &hfpll_regmap_config);
++ if (IS_ERR(regmap))
++ return PTR_ERR(regmap);
++
++ if (of_property_read_string_index(dev->of_node, "clock-output-names",
++ 0, &init.name))
++ return -ENODEV;
++
++ h->d = &hdata;
++ h->clkr.hw.init = &init;
++ spin_lock_init(&h->lock);
++
++ clk = devm_clk_register_regmap(&pdev->dev, &h->clkr);
++
++ return PTR_ERR_OR_ZERO(clk);
++}
++
++static struct platform_driver qcom_hfpll_driver = {
++ .probe = qcom_hfpll_probe,
++ .driver = {
++ .name = "qcom-hfpll",
++ .of_match_table = qcom_hfpll_match_table,
++ },
++};
++module_platform_driver(qcom_hfpll_driver);
++
++MODULE_DESCRIPTION("QCOM HFPLL Clock Driver");
++MODULE_LICENSE("GPL v2");
++MODULE_ALIAS("platform:qcom-hfpll");
diff --git a/target/linux/ipq806x/patches-3.18/139-clk-qcom-Add-IPQ806X-s-HFPLLs.patch b/target/linux/ipq806x/patches-3.18/139-clk-qcom-Add-IPQ806X-s-HFPLLs.patch
new file mode 100644
index 0000000..7fd53d1
--- /dev/null
+++ b/target/linux/ipq806x/patches-3.18/139-clk-qcom-Add-IPQ806X-s-HFPLLs.patch
@@ -0,0 +1,127 @@
+Content-Type: text/plain; charset="utf-8"
+MIME-Version: 1.0
+Content-Transfer-Encoding: 7bit
+Subject: [v3,08/13] clk: qcom: Add IPQ806X's HFPLLs
+From: Stephen Boyd <sboyd at codeaurora.org>
+X-Patchwork-Id: 6063241
+Message-Id: <1426920332-9340-9-git-send-email-sboyd at codeaurora.org>
+To: Mike Turquette <mturquette at linaro.org>, Stephen Boyd <sboyd at codeaurora.org>
+Cc: linux-kernel at vger.kernel.org, linux-arm-msm at vger.kernel.org,
+ linux-pm at vger.kernel.org, linux-arm-kernel at lists.infradead.org,
+ Viresh Kumar <viresh.kumar at linaro.org>
+Date: Fri, 20 Mar 2015 23:45:27 -0700
+
+Describe the HFPLLs present on IPQ806X devices.
+
+Signed-off-by: Stephen Boyd <sboyd at codeaurora.org>
+
+---
+drivers/clk/qcom/gcc-ipq806x.c | 83 ++++++++++++++++++++++++++++++++++++++++++
+ 1 file changed, 83 insertions(+)
+
+--- a/drivers/clk/qcom/gcc-ipq806x.c
++++ b/drivers/clk/qcom/gcc-ipq806x.c
+@@ -30,6 +30,7 @@
+ #include "clk-pll.h"
+ #include "clk-rcg.h"
+ #include "clk-branch.h"
++#include "clk-hfpll.h"
+ #include "reset.h"
+
+ static struct clk_pll pll0 = {
+@@ -102,6 +103,85 @@ static struct clk_regmap pll8_vote = {
+ },
+ };
+
++static struct hfpll_data hfpll0_data = {
++ .mode_reg = 0x3200,
++ .l_reg = 0x3208,
++ .m_reg = 0x320c,
++ .n_reg = 0x3210,
++ .config_reg = 0x3204,
++ .status_reg = 0x321c,
++ .config_val = 0x7845c665,
++ .droop_reg = 0x3214,
++ .droop_val = 0x0108c000,
++ .min_rate = 600000000UL,
++ .max_rate = 1800000000UL,
++};
++
++static struct clk_hfpll hfpll0 = {
++ .d = &hfpll0_data,
++ .clkr.hw.init = &(struct clk_init_data){
++ .parent_names = (const char *[]){ "pxo" },
++ .num_parents = 1,
++ .name = "hfpll0",
++ .ops = &clk_ops_hfpll,
++ .flags = CLK_IGNORE_UNUSED,
++ },
++ .lock = __SPIN_LOCK_UNLOCKED(hfpll0.lock),
++};
++
++static struct hfpll_data hfpll1_data = {
++ .mode_reg = 0x3240,
++ .l_reg = 0x3248,
++ .m_reg = 0x324c,
++ .n_reg = 0x3250,
++ .config_reg = 0x3244,
++ .status_reg = 0x325c,
++ .config_val = 0x7845c665,
++ .droop_reg = 0x3314,
++ .droop_val = 0x0108c000,
++ .min_rate = 600000000UL,
++ .max_rate = 1800000000UL,
++};
++
++static struct clk_hfpll hfpll1 = {
++ .d = &hfpll1_data,
++ .clkr.hw.init = &(struct clk_init_data){
++ .parent_names = (const char *[]){ "pxo" },
++ .num_parents = 1,
++ .name = "hfpll1",
++ .ops = &clk_ops_hfpll,
++ .flags = CLK_IGNORE_UNUSED,
++ },
++ .lock = __SPIN_LOCK_UNLOCKED(hfpll1.lock),
++};
++
++static struct hfpll_data hfpll_l2_data = {
++ .mode_reg = 0x3300,
++ .l_reg = 0x3308,
++ .m_reg = 0x330c,
++ .n_reg = 0x3310,
++ .config_reg = 0x3304,
++ .status_reg = 0x331c,
++ .config_val = 0x7845c665,
++ .droop_reg = 0x3314,
++ .droop_val = 0x0108c000,
++ .min_rate = 600000000UL,
++ .max_rate = 1800000000UL,
++};
++
++static struct clk_hfpll hfpll_l2 = {
++ .d = &hfpll_l2_data,
++ .clkr.hw.init = &(struct clk_init_data){
++ .parent_names = (const char *[]){ "pxo" },
++ .num_parents = 1,
++ .name = "hfpll_l2",
++ .ops = &clk_ops_hfpll,
++ .flags = CLK_IGNORE_UNUSED,
++ },
++ .lock = __SPIN_LOCK_UNLOCKED(hfpll_l2.lock),
++};
++
++
+ static struct clk_pll pll14 = {
+ .l_reg = 0x31c4,
+ .m_reg = 0x31c8,
+@@ -2261,6 +2341,9 @@ static struct clk_regmap *gcc_ipq806x_cl
+ [USB_FS1_XCVR_SRC] = &usb_fs1_xcvr_clk_src.clkr,
+ [USB_FS1_XCVR_CLK] = &usb_fs1_xcvr_clk.clkr,
+ [USB_FS1_SYSTEM_CLK] = &usb_fs1_sys_clk.clkr,
++ [PLL9] = &hfpll0.clkr,
++ [PLL10] = &hfpll1.clkr,
++ [PLL12] = &hfpll_l2.clkr,
+ };
+
+ static const struct qcom_reset_map gcc_ipq806x_resets[] = {
diff --git a/target/linux/ipq806x/patches-3.18/140-clk-qcom-Add-support-for-Krait-clocks.patch b/target/linux/ipq806x/patches-3.18/140-clk-qcom-Add-support-for-Krait-clocks.patch
new file mode 100644
index 0000000..63292e8
--- /dev/null
+++ b/target/linux/ipq806x/patches-3.18/140-clk-qcom-Add-support-for-Krait-clocks.patch
@@ -0,0 +1,271 @@
+Content-Type: text/plain; charset="utf-8"
+MIME-Version: 1.0
+Content-Transfer-Encoding: 7bit
+Subject: [v3,09/13] clk: qcom: Add support for Krait clocks
+From: Stephen Boyd <sboyd at codeaurora.org>
+X-Patchwork-Id: 6063251
+Message-Id: <1426920332-9340-10-git-send-email-sboyd at codeaurora.org>
+To: Mike Turquette <mturquette at linaro.org>, Stephen Boyd <sboyd at codeaurora.org>
+Cc: linux-kernel at vger.kernel.org, linux-arm-msm at vger.kernel.org,
+ linux-pm at vger.kernel.org, linux-arm-kernel at lists.infradead.org,
+ Viresh Kumar <viresh.kumar at linaro.org>
+Date: Fri, 20 Mar 2015 23:45:28 -0700
+
+The Krait clocks are made up of a series of muxes and a divider
+that choose between a fixed rate clock and dedicated HFPLLs for
+each CPU. Instead of using mmio accesses to remux parents, the
+Krait implementation exposes the remux control via cp15
+registers. Support these clocks.
+
+Signed-off-by: Stephen Boyd <sboyd at codeaurora.org>
+
+---
+drivers/clk/qcom/Kconfig | 4 ++
+ drivers/clk/qcom/Makefile | 1 +
+ drivers/clk/qcom/clk-krait.c | 166 +++++++++++++++++++++++++++++++++++++++++++
+ drivers/clk/qcom/clk-krait.h | 49 +++++++++++++
+ 4 files changed, 220 insertions(+)
+ create mode 100644 drivers/clk/qcom/clk-krait.c
+ create mode 100644 drivers/clk/qcom/clk-krait.h
+
+--- a/drivers/clk/qcom/Kconfig
++++ b/drivers/clk/qcom/Kconfig
+@@ -78,3 +78,7 @@ config QCOM_HFPLL
+ Support for the high-frequency PLLs present on Qualcomm devices.
+ Say Y if you want to support CPU frequency scaling on devices
+ such as MSM8974, APQ8084, etc.
++
++config KRAIT_CLOCKS
++ bool
++ select KRAIT_L2_ACCESSORS
+--- a/drivers/clk/qcom/Makefile
++++ b/drivers/clk/qcom/Makefile
+@@ -6,6 +6,7 @@ clk-qcom-y += clk-pll.o
+ clk-qcom-y += clk-rcg.o
+ clk-qcom-y += clk-rcg2.o
+ clk-qcom-y += clk-branch.o
++clk-qcom-$(CONFIG_KRAIT_CLOCKS) += clk-krait.o
+ clk-qcom-y += clk-hfpll.o
+ clk-qcom-y += reset.o
+
+--- /dev/null
++++ b/drivers/clk/qcom/clk-krait.c
+@@ -0,0 +1,166 @@
++/*
++ * Copyright (c) 2013-2014, The Linux Foundation. All rights reserved.
++ *
++ * This program is free software; you can redistribute it and/or modify
++ * it under the terms of the GNU General Public License version 2 and
++ * only version 2 as published by the Free Software Foundation.
++ *
++ * This program is distributed in the hope that it will be useful,
++ * but WITHOUT ANY WARRANTY; without even the implied warranty of
++ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
++ * GNU General Public License for more details.
++ */
++
++#include <linux/kernel.h>
++#include <linux/module.h>
++#include <linux/init.h>
++#include <linux/io.h>
++#include <linux/delay.h>
++#include <linux/err.h>
++#include <linux/clk-provider.h>
++#include <linux/spinlock.h>
++
++#include <asm/krait-l2-accessors.h>
++
++#include "clk-krait.h"
++
++/* Secondary and primary muxes share the same cp15 register */
++static DEFINE_SPINLOCK(krait_clock_reg_lock);
++
++#define LPL_SHIFT 8
++static void __krait_mux_set_sel(struct krait_mux_clk *mux, int sel)
++{
++ unsigned long flags;
++ u32 regval;
++
++ spin_lock_irqsave(&krait_clock_reg_lock, flags);
++ regval = krait_get_l2_indirect_reg(mux->offset);
++ regval &= ~(mux->mask << mux->shift);
++ regval |= (sel & mux->mask) << mux->shift;
++ if (mux->lpl) {
++ regval &= ~(mux->mask << (mux->shift + LPL_SHIFT));
++ regval |= (sel & mux->mask) << (mux->shift + LPL_SHIFT);
++ }
++ krait_set_l2_indirect_reg(mux->offset, regval);
++ spin_unlock_irqrestore(&krait_clock_reg_lock, flags);
++
++ /* Wait for switch to complete. */
++ mb();
++ udelay(1);
++}
++
++static int krait_mux_set_parent(struct clk_hw *hw, u8 index)
++{
++ struct krait_mux_clk *mux = to_krait_mux_clk(hw);
++ u32 sel;
++
++ sel = clk_mux_reindex(index, mux->parent_map, 0);
++ mux->en_mask = sel;
++ /* Don't touch mux if CPU is off as it won't work */
++ if (__clk_is_enabled(hw->clk))
++ __krait_mux_set_sel(mux, sel);
++ return 0;
++}
++
++static u8 krait_mux_get_parent(struct clk_hw *hw)
++{
++ struct krait_mux_clk *mux = to_krait_mux_clk(hw);
++ u32 sel;
++
++ sel = krait_get_l2_indirect_reg(mux->offset);
++ sel >>= mux->shift;
++ sel &= mux->mask;
++ mux->en_mask = sel;
++
++ return clk_mux_get_parent(hw, sel, mux->parent_map, 0);
++}
++
++static struct clk_hw *krait_mux_get_safe_parent(struct clk_hw *hw)
++{
++ int i;
++ struct krait_mux_clk *mux = to_krait_mux_clk(hw);
++ int num_parents = __clk_get_num_parents(hw->clk);
++
++ i = mux->safe_sel;
++ for (i = 0; i < num_parents; i++)
++ if (mux->safe_sel == mux->parent_map[i])
++ break;
++
++ return __clk_get_hw(clk_get_parent_by_index(hw->clk, i));
++}
++
++static int krait_mux_enable(struct clk_hw *hw)
++{
++ struct krait_mux_clk *mux = to_krait_mux_clk(hw);
++
++ __krait_mux_set_sel(mux, mux->en_mask);
++
++ return 0;
++}
++
++static void krait_mux_disable(struct clk_hw *hw)
++{
++ struct krait_mux_clk *mux = to_krait_mux_clk(hw);
++
++ __krait_mux_set_sel(mux, mux->safe_sel);
++}
++
++const struct clk_ops krait_mux_clk_ops = {
++ .enable = krait_mux_enable,
++ .disable = krait_mux_disable,
++ .set_parent = krait_mux_set_parent,
++ .get_parent = krait_mux_get_parent,
++ .determine_rate = __clk_mux_determine_rate_closest,
++ .get_safe_parent = krait_mux_get_safe_parent,
++};
++EXPORT_SYMBOL_GPL(krait_mux_clk_ops);
++
++/* The divider can divide by 2, 4, 6 and 8. But we only really need div-2. */
++static long krait_div2_round_rate(struct clk_hw *hw, unsigned long rate,
++ unsigned long *parent_rate)
++{
++ *parent_rate = __clk_round_rate(__clk_get_parent(hw->clk), rate * 2);
++ return DIV_ROUND_UP(*parent_rate, 2);
++}
++
++static int krait_div2_set_rate(struct clk_hw *hw, unsigned long rate,
++ unsigned long parent_rate)
++{
++ struct krait_div2_clk *d = to_krait_div2_clk(hw);
++ unsigned long flags;
++ u32 val;
++ u32 mask = BIT(d->width) - 1;
++
++ if (d->lpl)
++ mask = mask << (d->shift + LPL_SHIFT) | mask << d->shift;
++
++ spin_lock_irqsave(&krait_clock_reg_lock, flags);
++ val = krait_get_l2_indirect_reg(d->offset);
++ val &= ~mask;
++ krait_set_l2_indirect_reg(d->offset, val);
++ spin_unlock_irqrestore(&krait_clock_reg_lock, flags);
++
++ return 0;
++}
++
++static unsigned long
++krait_div2_recalc_rate(struct clk_hw *hw, unsigned long parent_rate)
++{
++ struct krait_div2_clk *d = to_krait_div2_clk(hw);
++ u32 mask = BIT(d->width) - 1;
++ u32 div;
++
++ div = krait_get_l2_indirect_reg(d->offset);
++ div >>= d->shift;
++ div &= mask;
++ div = (div + 1) * 2;
++
++ return DIV_ROUND_UP(parent_rate, div);
++}
++
++const struct clk_ops krait_div2_clk_ops = {
++ .round_rate = krait_div2_round_rate,
++ .set_rate = krait_div2_set_rate,
++ .recalc_rate = krait_div2_recalc_rate,
++};
++EXPORT_SYMBOL_GPL(krait_div2_clk_ops);
+--- /dev/null
++++ b/drivers/clk/qcom/clk-krait.h
+@@ -0,0 +1,49 @@
++/*
++ * Copyright (c) 2013, The Linux Foundation. All rights reserved.
++ *
++ * This program is free software; you can redistribute it and/or modify
++ * it under the terms of the GNU General Public License version 2 and
++ * only version 2 as published by the Free Software Foundation.
++ *
++ * This program is distributed in the hope that it will be useful,
++ * but WITHOUT ANY WARRANTY; without even the implied warranty of
++ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
++ * GNU General Public License for more details.
++ */
++
++#ifndef __QCOM_CLK_KRAIT_H
++#define __QCOM_CLK_KRAIT_H
++
++#include <linux/clk-provider.h>
++
++struct krait_mux_clk {
++ unsigned int *parent_map;
++ bool has_safe_parent;
++ u8 safe_sel;
++ u32 offset;
++ u32 mask;
++ u32 shift;
++ u32 en_mask;
++ bool lpl;
++
++ struct clk_hw hw;
++};
++
++#define to_krait_mux_clk(_hw) container_of(_hw, struct krait_mux_clk, hw)
++
++extern const struct clk_ops krait_mux_clk_ops;
++
++struct krait_div2_clk {
++ u32 offset;
++ u8 width;
++ u32 shift;
++ bool lpl;
++
++ struct clk_hw hw;
++};
++
++#define to_krait_div2_clk(_hw) container_of(_hw, struct krait_div2_clk, hw)
++
++extern const struct clk_ops krait_div2_clk_ops;
++
++#endif
diff --git a/target/linux/ipq806x/patches-3.18/141-clk-qcom-Add-KPSS-ACC-GCC-driver.patch b/target/linux/ipq806x/patches-3.18/141-clk-qcom-Add-KPSS-ACC-GCC-driver.patch
new file mode 100644
index 0000000..06b14d8
--- /dev/null
+++ b/target/linux/ipq806x/patches-3.18/141-clk-qcom-Add-KPSS-ACC-GCC-driver.patch
@@ -0,0 +1,205 @@
+Content-Type: text/plain; charset="utf-8"
+MIME-Version: 1.0
+Content-Transfer-Encoding: 7bit
+Subject: [v3,10/13] clk: qcom: Add KPSS ACC/GCC driver
+From: Stephen Boyd <sboyd at codeaurora.org>
+X-Patchwork-Id: 6063201
+Message-Id: <1426920332-9340-11-git-send-email-sboyd at codeaurora.org>
+To: Mike Turquette <mturquette at linaro.org>, Stephen Boyd <sboyd at codeaurora.org>
+Cc: linux-kernel at vger.kernel.org, linux-arm-msm at vger.kernel.org,
+ linux-pm at vger.kernel.org, linux-arm-kernel at lists.infradead.org,
+ Viresh Kumar <viresh.kumar at linaro.org>, <devicetree at vger.kernel.org>
+Date: Fri, 20 Mar 2015 23:45:29 -0700
+
+The ACC and GCC regions present in KPSSv1 contain registers to
+control clocks and power to each Krait CPU and L2. For CPUfreq
+purposes probe these devices and expose a mux clock that chooses
+between PXO and PLL8.
+
+Cc: <devicetree at vger.kernel.org>
+Signed-off-by: Stephen Boyd <sboyd at codeaurora.org>
+
+---
+.../devicetree/bindings/arm/msm/qcom,kpss-acc.txt | 7 ++
+ .../devicetree/bindings/arm/msm/qcom,kpss-gcc.txt | 28 +++++++
+ drivers/clk/qcom/Kconfig | 8 ++
+ drivers/clk/qcom/Makefile | 1 +
+ drivers/clk/qcom/kpss-xcc.c | 95 ++++++++++++++++++++++
+ 5 files changed, 139 insertions(+)
+ create mode 100644 Documentation/devicetree/bindings/arm/msm/qcom,kpss-gcc.txt
+ create mode 100644 drivers/clk/qcom/kpss-xcc.c
+
+--- a/Documentation/devicetree/bindings/arm/msm/qcom,kpss-acc.txt
++++ b/Documentation/devicetree/bindings/arm/msm/qcom,kpss-acc.txt
+@@ -21,10 +21,17 @@ PROPERTIES
+ the register region. An optional second element specifies
+ the base address and size of the alias register region.
+
++- clock-output-names:
++ Usage: optional
++ Value type: <string>
++ Definition: Name of the output clock. Typically acpuX_aux where X is a
++ CPU number starting at 0.
++
+ Example:
+
+ clock-controller at 2088000 {
+ compatible = "qcom,kpss-acc-v2";
+ reg = <0x02088000 0x1000>,
+ <0x02008000 0x1000>;
++ clock-output-names = "acpu0_aux";
+ };
+--- /dev/null
++++ b/Documentation/devicetree/bindings/arm/msm/qcom,kpss-gcc.txt
+@@ -0,0 +1,28 @@
++Krait Processor Sub-system (KPSS) Global Clock Controller (GCC)
++
++PROPERTIES
++
++- compatible:
++ Usage: required
++ Value type: <string>
++ Definition: should be one of:
++ "qcom,kpss-gcc"
++
++- reg:
++ Usage: required
++ Value type: <prop-encoded-array>
++ Definition: base address and size of the register region
++
++- clock-output-names:
++ Usage: required
++ Value type: <string>
++ Definition: Name of the output clock. Typically acpu_l2_aux indicating
++ an L2 cache auxiliary clock.
++
++Example:
++
++ l2cc: clock-controller at 2011000 {
++ compatible = "qcom,kpss-gcc";
++ reg = <0x2011000 0x1000>;
++ clock-output-names = "acpu_l2_aux";
++ };
+--- a/drivers/clk/qcom/Kconfig
++++ b/drivers/clk/qcom/Kconfig
+@@ -79,6 +79,14 @@ config QCOM_HFPLL
+ Say Y if you want to support CPU frequency scaling on devices
+ such as MSM8974, APQ8084, etc.
+
++config KPSS_XCC
++ tristate "KPSS Clock Controller"
++ depends on COMMON_CLK_QCOM
++ help
++ Support for the Krait ACC and GCC clock controllers. Say Y
++ if you want to support CPU frequency scaling on devices such
++ as MSM8960, APQ8064, etc.
++
+ config KRAIT_CLOCKS
+ bool
+ select KRAIT_L2_ACCESSORS
+--- a/drivers/clk/qcom/Makefile
++++ b/drivers/clk/qcom/Makefile
+@@ -18,4 +18,5 @@ obj-$(CONFIG_MSM_GCC_8960) += gcc-msm896
+ obj-$(CONFIG_MSM_GCC_8974) += gcc-msm8974.o
+ obj-$(CONFIG_MSM_MMCC_8960) += mmcc-msm8960.o
+ obj-$(CONFIG_MSM_MMCC_8974) += mmcc-msm8974.o
++obj-$(CONFIG_KPSS_XCC) += kpss-xcc.o
+ obj-$(CONFIG_QCOM_HFPLL) += hfpll.o
+--- /dev/null
++++ b/drivers/clk/qcom/kpss-xcc.c
+@@ -0,0 +1,95 @@
++/* Copyright (c) 2014-2015, The Linux Foundation. All rights reserved.
++ *
++ * This program is free software; you can redistribute it and/or modify
++ * it under the terms of the GNU General Public License version 2 and
++ * only version 2 as published by the Free Software Foundation.
++ *
++ * This program is distributed in the hope that it will be useful,
++ * but WITHOUT ANY WARRANTY; without even the implied warranty of
++ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
++ * GNU General Public License for more details.
++ */
++
++#include <linux/kernel.h>
++#include <linux/init.h>
++#include <linux/module.h>
++#include <linux/platform_device.h>
++#include <linux/err.h>
++#include <linux/io.h>
++#include <linux/of.h>
++#include <linux/of_device.h>
++#include <linux/clk.h>
++#include <linux/clk-provider.h>
++
++static const char *aux_parents[] = {
++ "pll8_vote",
++ "pxo",
++};
++
++static unsigned int aux_parent_map[] = {
++ 3,
++ 0,
++};
++
++static const struct of_device_id kpss_xcc_match_table[] = {
++ { .compatible = "qcom,kpss-acc-v1", .data = (void *)1UL },
++ { .compatible = "qcom,kpss-gcc" },
++ {}
++};
++MODULE_DEVICE_TABLE(of, kpss_xcc_match_table);
++
++static int kpss_xcc_driver_probe(struct platform_device *pdev)
++{
++ const struct of_device_id *id;
++ struct clk *clk;
++ struct resource *res;
++ void __iomem *base;
++ const char *name;
++
++ id = of_match_device(kpss_xcc_match_table, &pdev->dev);
++ if (!id)
++ return -ENODEV;
++
++ res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
++ base = devm_ioremap_resource(&pdev->dev, res);
++ if (IS_ERR(base))
++ return PTR_ERR(base);
++
++ if (id->data) {
++ if (of_property_read_string_index(pdev->dev.of_node,
++ "clock-output-names", 0, &name))
++ return -ENODEV;
++ base += 0x14;
++ } else {
++ name = "acpu_l2_aux";
++ base += 0x28;
++ }
++
++ clk = clk_register_mux_table(&pdev->dev, name, aux_parents,
++ ARRAY_SIZE(aux_parents), 0, base, 0, 0x3,
++ 0, aux_parent_map, NULL);
++
++ platform_set_drvdata(pdev, clk);
++
++ return PTR_ERR_OR_ZERO(clk);
++}
++
++static int kpss_xcc_driver_remove(struct platform_device *pdev)
++{
++ clk_unregister_mux(platform_get_drvdata(pdev));
++ return 0;
++}
++
++static struct platform_driver kpss_xcc_driver = {
++ .probe = kpss_xcc_driver_probe,
++ .remove = kpss_xcc_driver_remove,
++ .driver = {
++ .name = "kpss-xcc",
++ .of_match_table = kpss_xcc_match_table,
++ },
++};
++module_platform_driver(kpss_xcc_driver);
++
++MODULE_DESCRIPTION("Krait Processor Sub System (KPSS) Clock Driver");
++MODULE_LICENSE("GPL v2");
++MODULE_ALIAS("platform:kpss-xcc");
diff --git a/target/linux/ipq806x/patches-3.18/142-clk-qcom-Add-Krait-clock-controller-driver.patch b/target/linux/ipq806x/patches-3.18/142-clk-qcom-Add-Krait-clock-controller-driver.patch
new file mode 100644
index 0000000..98a09ac
--- /dev/null
+++ b/target/linux/ipq806x/patches-3.18/142-clk-qcom-Add-Krait-clock-controller-driver.patch
@@ -0,0 +1,435 @@
+Content-Type: text/plain; charset="utf-8"
+MIME-Version: 1.0
+Content-Transfer-Encoding: 7bit
+Subject: [v3,11/13] clk: qcom: Add Krait clock controller driver
+From: Stephen Boyd <sboyd at codeaurora.org>
+X-Patchwork-Id: 6063121
+Message-Id: <1426920332-9340-12-git-send-email-sboyd at codeaurora.org>
+To: Mike Turquette <mturquette at linaro.org>, Stephen Boyd <sboyd at codeaurora.org>
+Cc: linux-kernel at vger.kernel.org, linux-arm-msm at vger.kernel.org,
+ linux-pm at vger.kernel.org, linux-arm-kernel at lists.infradead.org,
+ Viresh Kumar <viresh.kumar at linaro.org>, <devicetree at vger.kernel.org>
+Date: Fri, 20 Mar 2015 23:45:30 -0700
+
+The Krait CPU clocks are made up of a primary mux and secondary
+mux for each CPU and the L2, controlled via cp15 accessors. For
+Kraits within KPSSv1 each secondary mux accepts a different aux
+source, but on KPSSv2 each secondary mux accepts the same aux
+source.
+
+Cc: <devicetree at vger.kernel.org>
+Signed-off-by: Stephen Boyd <sboyd at codeaurora.org>
+
+---
+.../devicetree/bindings/clock/qcom,krait-cc.txt | 22 ++
+ drivers/clk/qcom/Kconfig | 8 +
+ drivers/clk/qcom/Makefile | 1 +
+ drivers/clk/qcom/krait-cc.c | 352 +++++++++++++++++++++
+ 4 files changed, 383 insertions(+)
+ create mode 100644 Documentation/devicetree/bindings/clock/qcom,krait-cc.txt
+ create mode 100644 drivers/clk/qcom/krait-cc.c
+
+--- /dev/null
++++ b/Documentation/devicetree/bindings/clock/qcom,krait-cc.txt
+@@ -0,0 +1,22 @@
++Krait Clock Controller
++
++PROPERTIES
++
++- compatible:
++ Usage: required
++ Value type: <string>
++ Definition: must be one of:
++ "qcom,krait-cc-v1"
++ "qcom,krait-cc-v2"
++
++- #clock-cells:
++ Usage: required
++ Value type: <u32>
++ Definition: must be 1
++
++Example:
++
++ kraitcc: clock-controller {
++ compatible = "qcom,krait-cc-v1";
++ #clock-cells = <1>;
++ };
+--- a/drivers/clk/qcom/Kconfig
++++ b/drivers/clk/qcom/Kconfig
+@@ -87,6 +87,14 @@ config KPSS_XCC
+ if you want to support CPU frequency scaling on devices such
+ as MSM8960, APQ8064, etc.
+
++config KRAITCC
++ tristate "Krait Clock Controller"
++ depends on COMMON_CLK_QCOM && ARM
++ select KRAIT_CLOCKS
++ help
++ Support for the Krait CPU clocks on Qualcomm devices.
++ Say Y if you want to support CPU frequency scaling.
++
+ config KRAIT_CLOCKS
+ bool
+ select KRAIT_L2_ACCESSORS
+--- a/drivers/clk/qcom/Makefile
++++ b/drivers/clk/qcom/Makefile
+@@ -20,3 +20,4 @@ obj-$(CONFIG_MSM_MMCC_8960) += mmcc-msm8
+ obj-$(CONFIG_MSM_MMCC_8974) += mmcc-msm8974.o
+ obj-$(CONFIG_KPSS_XCC) += kpss-xcc.o
+ obj-$(CONFIG_QCOM_HFPLL) += hfpll.o
++obj-$(CONFIG_KRAITCC) += krait-cc.o
+--- /dev/null
++++ b/drivers/clk/qcom/krait-cc.c
+@@ -0,0 +1,352 @@
++/* Copyright (c) 2013-2015, The Linux Foundation. All rights reserved.
++ *
++ * This program is free software; you can redistribute it and/or modify
++ * it under the terms of the GNU General Public License version 2 and
++ * only version 2 as published by the Free Software Foundation.
++ *
++ * This program is distributed in the hope that it will be useful,
++ * but WITHOUT ANY WARRANTY; without even the implied warranty of
++ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
++ * GNU General Public License for more details.
++ */
++
++#include <linux/kernel.h>
++#include <linux/init.h>
++#include <linux/module.h>
++#include <linux/platform_device.h>
++#include <linux/err.h>
++#include <linux/io.h>
++#include <linux/of.h>
++#include <linux/of_device.h>
++#include <linux/clk.h>
++#include <linux/clk-provider.h>
++#include <linux/slab.h>
++
++#include "clk-krait.h"
++
++static unsigned int sec_mux_map[] = {
++ 2,
++ 0,
++};
++
++static unsigned int pri_mux_map[] = {
++ 1,
++ 2,
++ 0,
++};
++
++static int
++krait_add_div(struct device *dev, int id, const char *s, unsigned offset)
++{
++ struct krait_div2_clk *div;
++ struct clk_init_data init = {
++ .num_parents = 1,
++ .ops = &krait_div2_clk_ops,
++ .flags = CLK_SET_RATE_PARENT,
++ };
++ const char *p_names[1];
++ struct clk *clk;
++
++ div = devm_kzalloc(dev, sizeof(*div), GFP_KERNEL);
++ if (!div)
++ return -ENOMEM;
++
++ div->width = 2;
++ div->shift = 6;
++ div->lpl = id >= 0;
++ div->offset = offset;
++ div->hw.init = &init;
++
++ init.name = kasprintf(GFP_KERNEL, "hfpll%s_div", s);
++ if (!init.name)
++ return -ENOMEM;
++
++ init.parent_names = p_names;
++ p_names[0] = kasprintf(GFP_KERNEL, "hfpll%s", s);
++ if (!p_names[0]) {
++ kfree(init.name);
++ return -ENOMEM;
++ }
++
++ clk = devm_clk_register(dev, &div->hw);
++ kfree(p_names[0]);
++ kfree(init.name);
++
++ return PTR_ERR_OR_ZERO(clk);
++}
++
++static int
++krait_add_sec_mux(struct device *dev, int id, const char *s, unsigned offset,
++ bool unique_aux)
++{
++ struct krait_mux_clk *mux;
++ static const char *sec_mux_list[] = {
++ "acpu_aux",
++ "qsb",
++ };
++ struct clk_init_data init = {
++ .parent_names = sec_mux_list,
++ .num_parents = ARRAY_SIZE(sec_mux_list),
++ .ops = &krait_mux_clk_ops,
++ .flags = CLK_SET_RATE_PARENT,
++ };
++ struct clk *clk;
++
++ mux = devm_kzalloc(dev, sizeof(*mux), GFP_KERNEL);
++ if (!mux)
++ return -ENOMEM;
++
++ mux->offset = offset;
++ mux->lpl = id >= 0;
++ mux->has_safe_parent = true;
++ mux->safe_sel = 2;
++ mux->mask = 0x3;
++ mux->shift = 2;
++ mux->parent_map = sec_mux_map;
++ mux->hw.init = &init;
++
++ init.name = kasprintf(GFP_KERNEL, "krait%s_sec_mux", s);
++ if (!init.name)
++ return -ENOMEM;
++
++ if (unique_aux) {
++ sec_mux_list[0] = kasprintf(GFP_KERNEL, "acpu%s_aux", s);
++ if (!sec_mux_list[0]) {
++ clk = ERR_PTR(-ENOMEM);
++ goto err_aux;
++ }
++ }
++
++ clk = devm_clk_register(dev, &mux->hw);
++
++ if (unique_aux)
++ kfree(sec_mux_list[0]);
++err_aux:
++ kfree(init.name);
++ return PTR_ERR_OR_ZERO(clk);
++}
++
++static struct clk *
++krait_add_pri_mux(struct device *dev, int id, const char *s, unsigned offset)
++{
++ struct krait_mux_clk *mux;
++ const char *p_names[3];
++ struct clk_init_data init = {
++ .parent_names = p_names,
++ .num_parents = ARRAY_SIZE(p_names),
++ .ops = &krait_mux_clk_ops,
++ .flags = CLK_SET_RATE_PARENT,
++ };
++ struct clk *clk;
++
++ mux = devm_kzalloc(dev, sizeof(*mux), GFP_KERNEL);
++ if (!mux)
++ return ERR_PTR(-ENOMEM);
++
++ mux->has_safe_parent = true;
++ mux->safe_sel = 0;
++ mux->mask = 0x3;
++ mux->shift = 0;
++ mux->offset = offset;
++ mux->lpl = id >= 0;
++ mux->parent_map = pri_mux_map;
++ mux->hw.init = &init;
++
++ init.name = kasprintf(GFP_KERNEL, "krait%s_pri_mux", s);
++ if (!init.name)
++ return ERR_PTR(-ENOMEM);
++
++ p_names[0] = kasprintf(GFP_KERNEL, "hfpll%s", s);
++ if (!p_names[0]) {
++ clk = ERR_PTR(-ENOMEM);
++ goto err_p0;
++ }
++
++ p_names[1] = kasprintf(GFP_KERNEL, "hfpll%s_div", s);
++ if (!p_names[1]) {
++ clk = ERR_PTR(-ENOMEM);
++ goto err_p1;
++ }
++
++ p_names[2] = kasprintf(GFP_KERNEL, "krait%s_sec_mux", s);
++ if (!p_names[2]) {
++ clk = ERR_PTR(-ENOMEM);
++ goto err_p2;
++ }
++
++ clk = devm_clk_register(dev, &mux->hw);
++
++ kfree(p_names[2]);
++err_p2:
++ kfree(p_names[1]);
++err_p1:
++ kfree(p_names[0]);
++err_p0:
++ kfree(init.name);
++ return clk;
++}
++
++/* id < 0 for L2, otherwise id == physical CPU number */
++static struct clk *krait_add_clks(struct device *dev, int id, bool unique_aux)
++{
++ int ret;
++ unsigned offset;
++ void *p = NULL;
++ const char *s;
++ struct clk *clk;
++
++ if (id >= 0) {
++ offset = 0x4501 + (0x1000 * id);
++ s = p = kasprintf(GFP_KERNEL, "%d", id);
++ if (!s)
++ return ERR_PTR(-ENOMEM);
++ } else {
++ offset = 0x500;
++ s = "_l2";
++ }
++
++ ret = krait_add_div(dev, id, s, offset);
++ if (ret) {
++ clk = ERR_PTR(ret);
++ goto err;
++ }
++
++ ret = krait_add_sec_mux(dev, id, s, offset, unique_aux);
++ if (ret) {
++ clk = ERR_PTR(ret);
++ goto err;
++ }
++
++ clk = krait_add_pri_mux(dev, id, s, offset);
++err:
++ kfree(p);
++ return clk;
++}
++
++static struct clk *krait_of_get(struct of_phandle_args *clkspec, void *data)
++{
++ unsigned int idx = clkspec->args[0];
++ struct clk **clks = data;
++
++ if (idx >= 5) {
++ pr_err("%s: invalid clock index %d\n", __func__, idx);
++ return ERR_PTR(-EINVAL);
++ }
++
++ return clks[idx] ? : ERR_PTR(-ENODEV);
++}
++
++static const struct of_device_id krait_cc_match_table[] = {
++ { .compatible = "qcom,krait-cc-v1", (void *)1UL },
++ { .compatible = "qcom,krait-cc-v2" },
++ {}
++};
++MODULE_DEVICE_TABLE(of, krait_cc_match_table);
++
++static int krait_cc_probe(struct platform_device *pdev)
++{
++ struct device *dev = &pdev->dev;
++ const struct of_device_id *id;
++ unsigned long cur_rate, aux_rate;
++ int cpu;
++ struct clk *clk;
++ struct clk **clks;
++ struct clk *l2_pri_mux_clk;
++
++ id = of_match_device(krait_cc_match_table, dev);
++ if (!id)
++ return -ENODEV;
++
++ /* Rate is 1 because 0 causes problems for __clk_mux_determine_rate */
++ clk = clk_register_fixed_rate(dev, "qsb", NULL, CLK_IS_ROOT, 1);
++ if (IS_ERR(clk))
++ return PTR_ERR(clk);
++
++ if (!id->data) {
++ clk = clk_register_fixed_factor(dev, "acpu_aux",
++ "gpll0_vote", 0, 1, 2);
++ if (IS_ERR(clk))
++ return PTR_ERR(clk);
++ }
++
++ /* Krait configurations have at most 4 CPUs and one L2 */
++ clks = devm_kcalloc(dev, 5, sizeof(*clks), GFP_KERNEL);
++ if (!clks)
++ return -ENOMEM;
++
++ for_each_possible_cpu(cpu) {
++ clk = krait_add_clks(dev, cpu, id->data);
++ if (IS_ERR(clk))
++ return PTR_ERR(clk);
++ clks[cpu] = clk;
++ }
++
++ l2_pri_mux_clk = krait_add_clks(dev, -1, id->data);
++ if (IS_ERR(l2_pri_mux_clk))
++ return PTR_ERR(l2_pri_mux_clk);
++ clks[4] = l2_pri_mux_clk;
++
++ /*
++ * We don't want the CPU or L2 clocks to be turned off at late init
++ * if CPUFREQ or HOTPLUG configs are disabled. So, bump up the
++ * refcount of these clocks. Any cpufreq/hotplug manager can assume
++ * that the clocks have already been prepared and enabled by the time
++ * they take over.
++ */
++ for_each_online_cpu(cpu) {
++ clk_prepare_enable(l2_pri_mux_clk);
++ WARN(clk_prepare_enable(clks[cpu]),
++ "Unable to turn on CPU%d clock", cpu);
++ }
++
++ /*
++ * Force reinit of HFPLLs and muxes to overwrite any potential
++ * incorrect configuration of HFPLLs and muxes by the bootloader.
++ * While at it, also make sure the cores are running at known rates
++ * and print the current rate.
++ *
++ * The clocks are set to aux clock rate first to make sure the
++ * secondary mux is not sourcing off of QSB. The rate is then set to
++ * two different rates to force a HFPLL reinit under all
++ * circumstances.
++ */
++ cur_rate = clk_get_rate(l2_pri_mux_clk);
++ aux_rate = 384000000;
++ if (cur_rate == 1) {
++ pr_info("L2 @ QSB rate. Forcing new rate.\n");
++ cur_rate = aux_rate;
++ }
++ clk_set_rate(l2_pri_mux_clk, aux_rate);
++ clk_set_rate(l2_pri_mux_clk, 2);
++ clk_set_rate(l2_pri_mux_clk, cur_rate);
++ pr_info("L2 @ %lu KHz\n", clk_get_rate(l2_pri_mux_clk) / 1000);
++ for_each_possible_cpu(cpu) {
++ clk = clks[cpu];
++ cur_rate = clk_get_rate(clk);
++ if (cur_rate == 1) {
++ pr_info("CPU%d @ QSB rate. Forcing new rate.\n", cpu);
++ cur_rate = aux_rate;
++ }
++ clk_set_rate(clk, aux_rate);
++ clk_set_rate(clk, 2);
++ clk_set_rate(clk, cur_rate);
++ pr_info("CPU%d @ %lu KHz\n", cpu, clk_get_rate(clk) / 1000);
++ }
++
++ of_clk_add_provider(dev->of_node, krait_of_get, clks);
++
++ return 0;
++}
++
++static struct platform_driver krait_cc_driver = {
++ .probe = krait_cc_probe,
++ .driver = {
++ .name = "krait-cc",
++ .of_match_table = krait_cc_match_table,
++ },
++};
++module_platform_driver(krait_cc_driver);
++
++MODULE_DESCRIPTION("Krait CPU Clock Driver");
++MODULE_LICENSE("GPL v2");
++MODULE_ALIAS("platform:krait-cc");
diff --git a/target/linux/ipq806x/patches-3.18/143-cpufreq-Add-module-to-register-cpufreq-on-Krait-CPUs.patch b/target/linux/ipq806x/patches-3.18/143-cpufreq-Add-module-to-register-cpufreq-on-Krait-CPUs.patch
new file mode 100644
index 0000000..c3ca9b5
--- /dev/null
+++ b/target/linux/ipq806x/patches-3.18/143-cpufreq-Add-module-to-register-cpufreq-on-Krait-CPUs.patch
@@ -0,0 +1,304 @@
+Content-Type: text/plain; charset="utf-8"
+MIME-Version: 1.0
+Content-Transfer-Encoding: 7bit
+Subject: [v3,12/13] cpufreq: Add module to register cpufreq on Krait CPUs
+From: Stephen Boyd <sboyd at codeaurora.org>
+X-Patchwork-Id: 6063191
+Message-Id: <1426920332-9340-13-git-send-email-sboyd at codeaurora.org>
+To: Mike Turquette <mturquette at linaro.org>, Stephen Boyd <sboyd at codeaurora.org>
+Cc: linux-kernel at vger.kernel.org, linux-arm-msm at vger.kernel.org,
+ linux-pm at vger.kernel.org, linux-arm-kernel at lists.infradead.org,
+ Viresh Kumar <viresh.kumar at linaro.org>, <devicetree at vger.kernel.org>
+Date: Fri, 20 Mar 2015 23:45:31 -0700
+
+Register a cpufreq-generic device whenever we detect that a
+"qcom,krait" compatible CPU is present in DT.
+
+Cc: <devicetree at vger.kernel.org>
+Signed-off-by: Stephen Boyd <sboyd at codeaurora.org>
+
+---
+.../devicetree/bindings/arm/msm/qcom,pvs.txt | 38 ++++
+ drivers/cpufreq/Kconfig.arm | 9 +
+ drivers/cpufreq/Makefile | 1 +
+ drivers/cpufreq/qcom-cpufreq.c | 204 +++++++++++++++++++++
+ 4 files changed, 252 insertions(+)
+ create mode 100644 Documentation/devicetree/bindings/arm/msm/qcom,pvs.txt
+ create mode 100644 drivers/cpufreq/qcom-cpufreq.c
+
+--- /dev/null
++++ b/Documentation/devicetree/bindings/arm/msm/qcom,pvs.txt
+@@ -0,0 +1,38 @@
++Qualcomm Process Voltage Scaling Tables
++
++The node name is required to be "qcom,pvs". There shall only be one
++such node present in the root of the tree.
++
++PROPERTIES
++
++- qcom,pvs-format-a or qcom,pvs-format-b:
++ Usage: required
++ Value type: <empty>
++ Definition: Indicates the format of qcom,speedX-pvsY-bin-vZ properties.
++ If qcom,pvs-format-a is used the table is two columns
++ (frequency and voltage in that order). If qcom,pvs-format-b is used the table is three columns (frequency, voltage,
++ and current in that order).
++
++- qcom,speedX-pvsY-bin-vZ:
++ Usage: required
++ Value type: <prop-encoded-array>
++ Definition: The PVS table corresponding to the speed bin X, pvs bin Y,
++ and version Z.
++Example:
++
++ qcom,pvs {
++ qcom,pvs-format-a;
++ qcom,speed0-pvs0-bin-v0 =
++ < 384000000 950000 >,
++ < 486000000 975000 >,
++ < 594000000 1000000 >,
++ < 702000000 1025000 >,
++ < 810000000 1075000 >,
++ < 918000000 1100000 >,
++ < 1026000000 1125000 >,
++ < 1134000000 1175000 >,
++ < 1242000000 1200000 >,
++ < 1350000000 1225000 >,
++ < 1458000000 1237500 >,
++ < 1512000000 1250000 >;
++ };
+--- a/drivers/cpufreq/Kconfig.arm
++++ b/drivers/cpufreq/Kconfig.arm
+@@ -129,6 +129,15 @@ config ARM_OMAP2PLUS_CPUFREQ
+ depends on ARCH_OMAP2PLUS
+ default ARCH_OMAP2PLUS
+
++config ARM_QCOM_CPUFREQ
++ tristate "Qualcomm based"
++ depends on ARCH_QCOM
++ select PM_OPP
++ help
++ This adds the CPUFreq driver for Qualcomm SoC based boards.
++
++ If in doubt, say N.
++
+ config ARM_S3C_CPUFREQ
+ bool
+ help
+--- a/drivers/cpufreq/Makefile
++++ b/drivers/cpufreq/Makefile
+@@ -64,6 +64,7 @@ obj-$(CONFIG_ARM_OMAP2PLUS_CPUFREQ) += o
+ obj-$(CONFIG_PXA25x) += pxa2xx-cpufreq.o
+ obj-$(CONFIG_PXA27x) += pxa2xx-cpufreq.o
+ obj-$(CONFIG_PXA3xx) += pxa3xx-cpufreq.o
++obj-$(CONFIG_ARM_QCOM_CPUFREQ) += qcom-cpufreq.o
+ obj-$(CONFIG_ARM_S3C24XX_CPUFREQ) += s3c24xx-cpufreq.o
+ obj-$(CONFIG_ARM_S3C24XX_CPUFREQ_DEBUGFS) += s3c24xx-cpufreq-debugfs.o
+ obj-$(CONFIG_ARM_S3C2410_CPUFREQ) += s3c2410-cpufreq.o
+--- /dev/null
++++ b/drivers/cpufreq/qcom-cpufreq.c
+@@ -0,0 +1,204 @@
++/* Copyright (c) 2014, The Linux Foundation. All rights reserved.
++ *
++ * This program is free software; you can redistribute it and/or modify
++ * it under the terms of the GNU General Public License version 2 and
++ * only version 2 as published by the Free Software Foundation.
++ *
++ * This program is distributed in the hope that it will be useful,
++ * but WITHOUT ANY WARRANTY; without even the implied warranty of
++ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
++ * GNU General Public License for more details.
++ */
++
++#include <linux/cpu.h>
++#include <linux/err.h>
++#include <linux/init.h>
++#include <linux/io.h>
++#include <linux/kernel.h>
++#include <linux/module.h>
++#include <linux/of.h>
++#include <linux/platform_device.h>
++#include <linux/pm_opp.h>
++#include <linux/slab.h>
++#include <linux/cpufreq-dt.h>
++
++static void __init get_krait_bin_format_a(int *speed, int *pvs, int *pvs_ver)
++{
++ void __iomem *base;
++ u32 pte_efuse;
++
++ *speed = *pvs = *pvs_ver = 0;
++
++ base = ioremap(0x007000c0, 4);
++ if (!base) {
++ pr_warn("Unable to read efuse data. Defaulting to 0!\n");
++ return;
++ }
++
++ pte_efuse = readl_relaxed(base);
++ iounmap(base);
++
++ *speed = pte_efuse & 0xf;
++ if (*speed == 0xf)
++ *speed = (pte_efuse >> 4) & 0xf;
++
++ if (*speed == 0xf) {
++ *speed = 0;
++ pr_warn("Speed bin: Defaulting to %d\n", *speed);
++ } else {
++ pr_info("Speed bin: %d\n", *speed);
++ }
++
++ *pvs = (pte_efuse >> 10) & 0x7;
++ if (*pvs == 0x7)
++ *pvs = (pte_efuse >> 13) & 0x7;
++
++ if (*pvs == 0x7) {
++ *pvs = 0;
++ pr_warn("PVS bin: Defaulting to %d\n", *pvs);
++ } else {
++ pr_info("PVS bin: %d\n", *pvs);
++ }
++}
++
++static void __init get_krait_bin_format_b(int *speed, int *pvs, int *pvs_ver)
++{
++ u32 pte_efuse, redundant_sel;
++ void __iomem *base;
++
++ *speed = 0;
++ *pvs = 0;
++ *pvs_ver = 0;
++
++ base = ioremap(0xfc4b80b0, 8);
++ if (!base) {
++ pr_warn("Unable to read efuse data. Defaulting to 0!\n");
++ return;
++ }
++
++ pte_efuse = readl_relaxed(base);
++ redundant_sel = (pte_efuse >> 24) & 0x7;
++ *speed = pte_efuse & 0x7;
++ /* 4 bits of PVS are in efuse register bits 31, 8-6. */
++ *pvs = ((pte_efuse >> 28) & 0x8) | ((pte_efuse >> 6) & 0x7);
++ *pvs_ver = (pte_efuse >> 4) & 0x3;
++
++ switch (redundant_sel) {
++ case 1:
++ *speed = (pte_efuse >> 27) & 0xf;
++ break;
++ case 2:
++ *pvs = (pte_efuse >> 27) & 0xf;
++ break;
++ }
++
++ /* Check SPEED_BIN_BLOW_STATUS */
++ if (pte_efuse & BIT(3)) {
++ pr_info("Speed bin: %d\n", *speed);
++ } else {
++ pr_warn("Speed bin not set. Defaulting to 0!\n");
++ *speed = 0;
++ }
++
++ /* Check PVS_BLOW_STATUS */
++ pte_efuse = readl_relaxed(base + 0x4) & BIT(21);
++ if (pte_efuse) {
++ pr_info("PVS bin: %d\n", *pvs);
++ } else {
++ pr_warn("PVS bin not set. Defaulting to 0!\n");
++ *pvs = 0;
++ }
++
++ pr_info("PVS version: %d\n", *pvs_ver);
++ iounmap(base);
++}
++
++static int __init qcom_cpufreq_populate_opps(void)
++{
++ int len, rows, cols, i, k, speed, pvs, pvs_ver;
++ char table_name[] = "qcom,speedXX-pvsXX-bin-vXX";
++ struct device_node *np;
++ struct device *dev;
++ int cpu = 0;
++
++ np = of_find_node_by_name(NULL, "qcom,pvs");
++ if (!np)
++ return -ENODEV;
++
++ if (of_property_read_bool(np, "qcom,pvs-format-a")) {
++ get_krait_bin_format_a(&speed, &pvs, &pvs_ver);
++ cols = 2;
++ } else if (of_property_read_bool(np, "qcom,pvs-format-b")) {
++ get_krait_bin_format_b(&speed, &pvs, &pvs_ver);
++ cols = 3;
++ } else {
++ return -ENODEV;
++ }
++
++ snprintf(table_name, sizeof(table_name),
++ "qcom,speed%d-pvs%d-bin-v%d", speed, pvs, pvs_ver);
++
++ if (!of_find_property(np, table_name, &len))
++ return -EINVAL;
++
++ len /= sizeof(u32);
++ if (len % cols || len == 0)
++ return -EINVAL;
++
++ rows = len / cols;
++
++ for (i = 0, k = 0; i < rows; i++) {
++ u32 freq, volt;
++
++ of_property_read_u32_index(np, table_name, k++, &freq);
++ of_property_read_u32_index(np, table_name, k++, &volt);
++ while (k % cols)
++ k++; /* Skip uA entries if present */
++ for (cpu = 0; cpu < num_possible_cpus(); cpu++) {
++ dev = get_cpu_device(cpu);
++ if (!dev)
++ return -ENODEV;
++ if (dev_pm_opp_add(dev, freq, volt))
++ pr_warn("failed to add OPP %u\n", freq);
++ }
++ }
++
++ return 0;
++}
++
++static int __init qcom_cpufreq_driver_init(void)
++{
++ struct cpufreq_dt_platform_data pdata = { .independent_clocks = true };
++ struct platform_device_info devinfo = {
++ .name = "cpufreq-dt",
++ .data = &pdata,
++ .size_data = sizeof(pdata),
++ };
++ struct device *cpu_dev;
++ struct device_node *np;
++ int ret;
++
++ cpu_dev = get_cpu_device(0);
++ if (!cpu_dev)
++ return -ENODEV;
++
++ np = of_node_get(cpu_dev->of_node);
++ if (!np)
++ return -ENOENT;
++
++ if (!of_device_is_compatible(np, "qcom,krait")) {
++ of_node_put(np);
++ return -ENODEV;
++ }
++ of_node_put(np);
++
++ ret = qcom_cpufreq_populate_opps();
++ if (ret)
++ return ret;
++
++ return PTR_ERR_OR_ZERO(platform_device_register_full(&devinfo));
++}
++module_init(qcom_cpufreq_driver_init);
++
++MODULE_DESCRIPTION("Qualcomm CPUfreq driver");
++MODULE_LICENSE("GPL v2");
diff --git a/target/linux/ipq806x/patches-3.18/144-ARM-dts-qcom-Add-necessary-DT-data-for-Krait-cpufreq.patch b/target/linux/ipq806x/patches-3.18/144-ARM-dts-qcom-Add-necessary-DT-data-for-Krait-cpufreq.patch
new file mode 100644
index 0000000..9f8d8cb
--- /dev/null
+++ b/target/linux/ipq806x/patches-3.18/144-ARM-dts-qcom-Add-necessary-DT-data-for-Krait-cpufreq.patch
@@ -0,0 +1,100 @@
+--- a/arch/arm/boot/dts/qcom-ipq8064.dtsi
++++ b/arch/arm/boot/dts/qcom-ipq8064.dtsi
+@@ -23,6 +23,11 @@
+ next-level-cache = <&L2>;
+ qcom,acc = <&acc0>;
+ qcom,saw = <&saw0>;
++ clocks = <&kraitcc 0>;
++ clock-names = "cpu";
++ clock-latency = <100000>;
++ core-supply = <&smb208_s2a>;
++ voltage-tolerance = <5>;
+ };
+
+ cpu at 1 {
+@@ -33,11 +38,24 @@
+ next-level-cache = <&L2>;
+ qcom,acc = <&acc1>;
+ qcom,saw = <&saw1>;
++ clocks = <&kraitcc 1>;
++ clock-names = "cpu";
++ clock-latency = <100000>;
++ core-supply = <&smb208_s2b>;
+ };
+
+ L2: l2-cache {
+ compatible = "cache";
+ cache-level = <2>;
++ clocks = <&kraitcc 4>;
++ clock-names = "cache";
++ cache-points-kHz = <
++ /* kHz uV CPU kHz */
++ 1200000 1150000 1200000
++ 1000000 1100000 600000
++ 384000 1100000 384000
++ >;
++ vdd_dig-supply = <&smb208_s1a>;
+ };
+ };
+
+@@ -70,6 +88,46 @@
+ };
+ };
+
++ kraitcc: clock-controller {
++ compatible = "qcom,krait-cc-v1";
++ #clock-cells = <1>;
++ };
++
++ qcom,pvs {
++ qcom,pvs-format-a;
++ qcom,speed0-pvs0-bin-v0 =
++ < 1400000000 1250000 >,
++ < 1200000000 1200000 >,
++ < 1000000000 1150000 >,
++ < 800000000 1100000 >,
++ < 600000000 1050000 >,
++ < 384000000 1000000 >;
++
++ qcom,speed0-pvs1-bin-v0 =
++ < 1400000000 1175000 >,
++ < 1200000000 1125000 >,
++ < 1000000000 1075000 >,
++ < 800000000 1025000 >,
++ < 600000000 975000 >,
++ < 384000000 925000 >;
++
++ qcom,speed0-pvs2-bin-v0 =
++ < 1400000000 1125000 >,
++ < 1200000000 1075000 >,
++ < 1000000000 1025000 >,
++ < 800000000 995000 >,
++ < 600000000 925000 >,
++ < 384000000 875000 >;
++
++ qcom,speed0-pvs3-bin-v0 =
++ < 1400000000 1050000 >,
++ < 1200000000 1000000 >,
++ < 1000000000 950000 >,
++ < 800000000 900000 >,
++ < 600000000 850000 >,
++ < 384000000 800000 >;
++ };
++
+ soc: soc {
+ #address-cells = <1>;
+ #size-cells = <1>;
+@@ -170,11 +228,13 @@
+ acc0: clock-controller at 2088000 {
+ compatible = "qcom,kpss-acc-v1";
+ reg = <0x02088000 0x1000>, <0x02008000 0x1000>;
++ clock-output-names = "acpu0_aux";
+ };
+
+ acc1: clock-controller at 2098000 {
+ compatible = "qcom,kpss-acc-v1";
+ reg = <0x02098000 0x1000>, <0x02008000 0x1000>;
++ clock-output-names = "acpu1_aux";
+ };
+
+ l2cc: clock-controller at 2011000 {
diff --git a/target/linux/ipq806x/patches-3.18/145-cpufreq-Add-a-cpufreq-krait-based-on-cpufre.patch b/target/linux/ipq806x/patches-3.18/145-cpufreq-Add-a-cpufreq-krait-based-on-cpufre.patch
new file mode 100644
index 0000000..15cabf3
--- /dev/null
+++ b/target/linux/ipq806x/patches-3.18/145-cpufreq-Add-a-cpufreq-krait-based-on-cpufre.patch
@@ -0,0 +1,461 @@
+From dd77db4143290689d3a5e1ec61627233d0711b66 Mon Sep 17 00:00:00 2001
+From: Stephen Boyd <sboyd at codeaurora.org>
+Date: Fri, 30 May 2014 16:36:11 -0700
+Subject: [PATCH] FROMLIST: cpufreq: Add a cpufreq-krait based on cpufreq-cpu0
+
+Krait processors have individual clocks for each CPU that can
+scale independently from one another. cpufreq-cpu0 is fairly
+close to this, but assumes that there is only one clock for all
+CPUs. Add a driver to support the Krait configuration.
+
+TODO: Merge into cpufreq-cpu0? Or make generic?
+
+Signed-off-by: Stephen Boyd <sboyd at codeaurora.org>
+
+---
+ drivers/cpufreq/Kconfig | 13 +++
+ drivers/cpufreq/Makefile | 1 +
+ drivers/cpufreq/cpufreq-krait.c | 190 ++++++++++++++++++++++++++++++++++++++++
+ 3 files changed, 204 insertions(+)
+ create mode 100644 drivers/cpufreq/cpufreq-krait.c
+
+--- a/drivers/cpufreq/Kconfig
++++ b/drivers/cpufreq/Kconfig
+@@ -196,6 +196,19 @@ config CPUFREQ_DT
+
+ If in doubt, say N.
+
++config GENERIC_CPUFREQ_KRAIT
++ tristate "Krait cpufreq driver"
++ depends on HAVE_CLK && OF
++ # if CPU_THERMAL is on and THERMAL=m, CPU0 cannot be =y:
++ depends on !CPU_THERMAL || THERMAL
++ select PM_OPP
++ help
++ This adds a generic cpufreq driver for CPU0 frequency management.
++ It supports both uniprocessor (UP) and symmetric multiprocessor (SMP)
++ systems which share clock and voltage across all CPUs.
++
++ If in doubt, say N.
++
+ menu "x86 CPU frequency scaling drivers"
+ depends on X86
+ source "drivers/cpufreq/Kconfig.x86"
+--- a/drivers/cpufreq/Makefile
++++ b/drivers/cpufreq/Makefile
+@@ -14,6 +14,7 @@ obj-$(CONFIG_CPU_FREQ_GOV_CONSERVATIVE)
+ obj-$(CONFIG_CPU_FREQ_GOV_COMMON) += cpufreq_governor.o
+
+ obj-$(CONFIG_CPUFREQ_DT) += cpufreq-dt.o
++obj-$(CONFIG_GENERIC_CPUFREQ_KRAIT) += cpufreq-krait.o
+
+ ##################################################################################
+ # x86 drivers.
+--- /dev/null
++++ b/drivers/cpufreq/cpufreq-krait.c
+@@ -0,0 +1,390 @@
++/*
++ * Copyright (C) 2012 Freescale Semiconductor, Inc.
++ * Copyright (c) 2014, The Linux Foundation. All rights reserved.
++ *
++ * The OPP code in function krait_set_target() is reused from
++ * drivers/cpufreq/omap-cpufreq.c
++ *
++ * This program is free software; you can redistribute it and/or modify
++ * it under the terms of the GNU General Public License version 2 as
++ * published by the Free Software Foundation.
++ */
++
++#include <linux/clk.h>
++#include <linux/cpu.h>
++#include <linux/cpu_cooling.h>
++#include <linux/cpufreq.h>
++#include <linux/cpumask.h>
++#include <linux/err.h>
++#include <linux/module.h>
++#include <linux/of.h>
++#include <linux/pm_opp.h>
++#include <linux/platform_device.h>
++#include <linux/regulator/consumer.h>
++#include <linux/slab.h>
++#include <linux/thermal.h>
++
++static unsigned int transition_latency;
++static unsigned int voltage_tolerance; /* in percentage */
++
++static struct device *cpu_dev;
++static DEFINE_PER_CPU(struct clk *, krait_cpu_clks);
++static DEFINE_PER_CPU(struct regulator *, krait_supply_core);
++static struct cpufreq_frequency_table *freq_table;
++static struct thermal_cooling_device *cdev;
++
++struct cache_points {
++ unsigned long cache_freq;
++ unsigned int cache_volt;
++ unsigned long cpu_freq;
++};
++
++static struct regulator *krait_l2_reg;
++static struct clk *krait_l2_clk;
++static struct cache_points *krait_l2_points;
++static int nr_krait_l2_points;
++
++static int krait_parse_cache_points(struct device *dev,
++ struct device_node *of_node)
++{
++ const struct property *prop;
++ const __be32 *val;
++ int nr, i;
++
++ prop = of_find_property(of_node, "cache-points-kHz", NULL);
++ if (!prop)
++ return -ENODEV;
++ if (!prop->value)
++ return -ENODATA;
++
++ /*
++ * Each OPP is a set of tuples consisting of frequency and
++ * cpu-frequency like <freq-kHz volt-uV freq-kHz>.
++ */
++ nr = prop->length / sizeof(u32);
++ if (nr % 3) {
++ dev_err(dev, "%s: Invalid cache points\n", __func__);
++ return -EINVAL;
++ }
++ nr /= 3;
++
++ krait_l2_points = devm_kcalloc(dev, nr, sizeof(*krait_l2_points),
++ GFP_KERNEL);
++ if (!krait_l2_points)
++ return -ENOMEM;
++ nr_krait_l2_points = nr;
++
++ for (i = 0, val = prop->value; i < nr; i++) {
++ unsigned long cache_freq = be32_to_cpup(val++) * 1000;
++ unsigned int cache_volt = be32_to_cpup(val++);
++ unsigned long cpu_freq = be32_to_cpup(val++) * 1000;
++
++ krait_l2_points[i].cache_freq = cache_freq;
++ krait_l2_points[i].cache_volt = cache_volt;
++ krait_l2_points[i].cpu_freq = cpu_freq;
++ }
++
++ return 0;
++}
++
++static int krait_set_target(struct cpufreq_policy *policy, unsigned int index)
++{
++ struct dev_pm_opp *opp;
++ unsigned long volt = 0, volt_old = 0, tol = 0;
++ unsigned long freq, max_cpu_freq = 0;
++ unsigned int old_freq, new_freq;
++ long freq_Hz, freq_exact;
++ int ret, i;
++ struct clk *cpu_clk;
++ struct regulator *core;
++ unsigned int cpu;
++
++ cpu_clk = per_cpu(krait_cpu_clks, policy->cpu);
++
++ freq_Hz = clk_round_rate(cpu_clk, freq_table[index].frequency * 1000);
++ if (freq_Hz <= 0)
++ freq_Hz = freq_table[index].frequency * 1000;
++
++ freq_exact = freq_Hz;
++ new_freq = freq_Hz / 1000;
++ old_freq = clk_get_rate(cpu_clk) / 1000;
++
++ core = per_cpu(krait_supply_core, policy->cpu);
++
++ rcu_read_lock();
++ opp = dev_pm_opp_find_freq_ceil(cpu_dev, &freq_Hz);
++ if (IS_ERR(opp)) {
++ rcu_read_unlock();
++ pr_err("failed to find OPP for %ld\n", freq_Hz);
++ return PTR_ERR(opp);
++ }
++ volt = dev_pm_opp_get_voltage(opp);
++ rcu_read_unlock();
++ tol = volt * voltage_tolerance / 100;
++ volt_old = regulator_get_voltage(core);
++
++ pr_debug("%u MHz, %ld mV --> %u MHz, %ld mV\n",
++ old_freq / 1000, volt_old ? volt_old / 1000 : -1,
++ new_freq / 1000, volt ? volt / 1000 : -1);
++
++ /* scaling up? scale voltage before frequency */
++ if (new_freq > old_freq) {
++ ret = regulator_set_voltage_tol(core, volt, tol);
++ if (ret) {
++ pr_err("failed to scale voltage up: %d\n", ret);
++ return ret;
++ }
++ }
++
++ ret = clk_set_rate(cpu_clk, freq_exact);
++ if (ret) {
++ pr_err("failed to set clock rate: %d\n", ret);
++ return ret;
++ }
++
++ /* scaling down? scale voltage after frequency */
++ if (new_freq < old_freq) {
++ ret = regulator_set_voltage_tol(core, volt, tol);
++ if (ret) {
++ pr_err("failed to scale voltage down: %d\n", ret);
++ clk_set_rate(cpu_clk, old_freq * 1000);
++ }
++ }
++
++ for_each_possible_cpu(cpu) {
++ freq = clk_get_rate(per_cpu(krait_cpu_clks, cpu));
++ max_cpu_freq = max(max_cpu_freq, freq);
++ }
++
++ for (i = 0; i < nr_krait_l2_points; i++) {
++ if (max_cpu_freq >= krait_l2_points[i].cpu_freq) {
++ if (krait_l2_reg) {
++ ret = regulator_set_voltage_tol(krait_l2_reg,
++ krait_l2_points[i].cache_volt,
++ tol);
++ if (ret) {
++ pr_err("failed to scale l2 voltage: %d\n",
++ ret);
++ }
++ }
++ ret = clk_set_rate(krait_l2_clk,
++ krait_l2_points[i].cache_freq);
++ if (ret)
++ pr_err("failed to scale l2 clk: %d\n", ret);
++ break;
++ }
++
++ }
++
++ return ret;
++}
++
++static int krait_cpufreq_init(struct cpufreq_policy *policy)
++{
++ int ret;
++
++ policy->clk = per_cpu(krait_cpu_clks, policy->cpu);
++
++ ret = cpufreq_table_validate_and_show(policy, freq_table);
++ if (ret) {
++ pr_err("%s: invalid frequency table: %d\n", __func__, ret);
++ return ret;
++ }
++
++ policy->cpuinfo.transition_latency = transition_latency;
++
++ return 0;
++}
++
++static struct cpufreq_driver krait_cpufreq_driver = {
++ .flags = CPUFREQ_STICKY,
++ .verify = cpufreq_generic_frequency_table_verify,
++ .target_index = krait_set_target,
++ .get = cpufreq_generic_get,
++ .init = krait_cpufreq_init,
++ .name = "generic_krait",
++ .attr = cpufreq_generic_attr,
++};
++
++static int krait_cpufreq_probe(struct platform_device *pdev)
++{
++ struct device_node *np, *cache;
++ int ret, i;
++ unsigned int cpu;
++ struct device *dev;
++ struct clk *clk;
++ struct regulator *core;
++ unsigned long freq_Hz, freq, max_cpu_freq;
++ struct dev_pm_opp *opp;
++ unsigned long volt, tol;
++
++ cpu_dev = get_cpu_device(0);
++ if (!cpu_dev) {
++ pr_err("failed to get krait device\n");
++ return -ENODEV;
++ }
++
++ np = of_node_get(cpu_dev->of_node);
++ if (!np) {
++ pr_err("failed to find krait node\n");
++ return -ENOENT;
++ }
++
++ ret = dev_pm_opp_init_cpufreq_table(cpu_dev, &freq_table);
++ if (ret) {
++ pr_err("failed to init cpufreq table: %d\n", ret);
++ goto out_put_node;
++ }
++
++ of_property_read_u32(np, "voltage-tolerance", &voltage_tolerance);
++
++ if (of_property_read_u32(np, "clock-latency", &transition_latency))
++ transition_latency = CPUFREQ_ETERNAL;
++
++ cache = of_find_next_cache_node(np);
++ if (cache) {
++ struct device_node *vdd;
++
++ vdd = of_parse_phandle(cache, "vdd_dig-supply", 0);
++ if (vdd) {
++ krait_l2_reg = regulator_get(NULL, vdd->name);
++ if (IS_ERR(krait_l2_reg)) {
++ pr_warn("failed to get l2 vdd_dig supply\n");
++ krait_l2_reg = NULL;
++ }
++ of_node_put(vdd);
++ }
++
++ krait_l2_clk = of_clk_get(cache, 0);
++ if (!IS_ERR(krait_l2_clk)) {
++ ret = krait_parse_cache_points(&pdev->dev, cache);
++ if (ret)
++ clk_put(krait_l2_clk);
++ }
++ if (IS_ERR(krait_l2_clk) || ret)
++ krait_l2_clk = NULL;
++ }
++
++ for_each_possible_cpu(cpu) {
++ dev = get_cpu_device(cpu);
++ if (!dev) {
++ pr_err("failed to get krait device\n");
++ ret = -ENOENT;
++ goto out_free_table;
++ }
++ per_cpu(krait_cpu_clks, cpu) = clk = devm_clk_get(dev, NULL);
++ if (IS_ERR(clk)) {
++ ret = PTR_ERR(clk);
++ goto out_free_table;
++ }
++ core = devm_regulator_get(dev, "core");
++ if (IS_ERR(core)) {
++ pr_debug("failed to get core regulator\n");
++ ret = PTR_ERR(core);
++ goto out_free_table;
++ }
++ per_cpu(krait_supply_core, cpu) = core;
++
++ freq_Hz = clk_get_rate(clk);
++
++ rcu_read_lock();
++ opp = dev_pm_opp_find_freq_ceil(cpu_dev, &freq_Hz);
++ if (IS_ERR(opp)) {
++ rcu_read_unlock();
++ pr_err("failed to find OPP for %ld\n", freq_Hz);
++ ret = PTR_ERR(opp);
++ goto out_free_table;
++ }
++ volt = dev_pm_opp_get_voltage(opp);
++ rcu_read_unlock();
++
++ tol = volt * voltage_tolerance / 100;
++ ret = regulator_set_voltage_tol(core, volt, tol);
++ if (ret) {
++ pr_err("failed to scale voltage up: %d\n", ret);
++ goto out_free_table;
++ }
++ ret = regulator_enable(core);
++ if (ret) {
++ pr_err("failed to enable regulator: %d\n", ret);
++ goto out_free_table;
++ }
++ max_cpu_freq = max(max_cpu_freq, freq);
++ }
++
++ for (i = 0; i < nr_krait_l2_points; i++) {
++ if (max_cpu_freq >= krait_l2_points[i].cpu_freq) {
++ if (krait_l2_reg) {
++ ret = regulator_set_voltage_tol(krait_l2_reg,
++ krait_l2_points[i].cache_volt,
++ tol);
++ if (ret)
++ pr_err("failed to scale l2 voltage: %d\n",
++ ret);
++ ret = regulator_enable(krait_l2_reg);
++ if (ret)
++ pr_err("failed to enable l2 voltage: %d\n",
++ ret);
++ }
++ break;
++ }
++
++ }
++
++ ret = cpufreq_register_driver(&krait_cpufreq_driver);
++ if (ret) {
++ pr_err("failed register driver: %d\n", ret);
++ goto out_free_table;
++ }
++ of_node_put(np);
++
++ /*
++ * For now, just loading the cooling device;
++ * thermal DT code takes care of matching them.
++ */
++ for_each_possible_cpu(cpu) {
++ dev = get_cpu_device(cpu);
++ np = of_node_get(dev->of_node);
++ if (of_find_property(np, "#cooling-cells", NULL)) {
++ cdev = of_cpufreq_cooling_register(np, cpumask_of(cpu));
++ if (IS_ERR(cdev))
++ pr_err("running cpufreq without cooling device: %ld\n",
++ PTR_ERR(cdev));
++ }
++ of_node_put(np);
++ }
++
++ return 0;
++
++out_free_table:
++ regulator_put(krait_l2_reg);
++ clk_put(krait_l2_clk);
++ dev_pm_opp_free_cpufreq_table(cpu_dev, &freq_table);
++out_put_node:
++ of_node_put(np);
++ return ret;
++}
++
++static int krait_cpufreq_remove(struct platform_device *pdev)
++{
++ cpufreq_cooling_unregister(cdev);
++ cpufreq_unregister_driver(&krait_cpufreq_driver);
++ dev_pm_opp_free_cpufreq_table(cpu_dev, &freq_table);
++ clk_put(krait_l2_clk);
++ regulator_put(krait_l2_reg);
++
++ return 0;
++}
++
++static struct platform_driver krait_cpufreq_platdrv = {
++ .driver = {
++ .name = "cpufreq-krait",
++ .owner = THIS_MODULE,
++ },
++ .probe = krait_cpufreq_probe,
++ .remove = krait_cpufreq_remove,
++};
++module_platform_driver(krait_cpufreq_platdrv);
++
++MODULE_DESCRIPTION("Krait CPUfreq driver");
++MODULE_LICENSE("GPL v2");
+--- a/drivers/cpufreq/qcom-cpufreq.c
++++ b/drivers/cpufreq/qcom-cpufreq.c
+@@ -168,11 +168,8 @@ static int __init qcom_cpufreq_populate_
+
+ static int __init qcom_cpufreq_driver_init(void)
+ {
+- struct cpufreq_dt_platform_data pdata = { .independent_clocks = true };
+ struct platform_device_info devinfo = {
+- .name = "cpufreq-dt",
+- .data = &pdata,
+- .size_data = sizeof(pdata),
++ .name = "cpufreq-krait",
+ };
+ struct device *cpu_dev;
+ struct device_node *np;
diff --git a/target/linux/ipq806x/patches-3.18/700-add-gmac-dts-suport.patch b/target/linux/ipq806x/patches-3.18/700-add-gmac-dts-suport.patch
index 2981da6..f0c511a 100644
--- a/target/linux/ipq806x/patches-3.18/700-add-gmac-dts-suport.patch
+++ b/target/linux/ipq806x/patches-3.18/700-add-gmac-dts-suport.patch
@@ -127,7 +127,7 @@
/ {
model = "Qualcomm IPQ8064";
-@@ -577,5 +578,42 @@
+@@ -637,5 +638,42 @@
dr_mode = "host";
};
};
diff --git a/target/linux/ipq806x/patches-4.0/133-ARM-Add-Krait-L2-register-accessor-functions.patch b/target/linux/ipq806x/patches-4.0/133-ARM-Add-Krait-L2-register-accessor-functions.patch
new file mode 100644
index 0000000..36a92c8
--- /dev/null
+++ b/target/linux/ipq806x/patches-4.0/133-ARM-Add-Krait-L2-register-accessor-functions.patch
@@ -0,0 +1,144 @@
+Content-Type: text/plain; charset="utf-8"
+MIME-Version: 1.0
+Content-Transfer-Encoding: 7bit
+Subject: [v3,01/13] ARM: Add Krait L2 register accessor functions
+From: Stephen Boyd <sboyd at codeaurora.org>
+X-Patchwork-Id: 6063051
+Message-Id: <1426920332-9340-2-git-send-email-sboyd at codeaurora.org>
+To: Mike Turquette <mturquette at linaro.org>, Stephen Boyd <sboyd at codeaurora.org>
+Cc: linux-kernel at vger.kernel.org, linux-arm-msm at vger.kernel.org,
+ linux-pm at vger.kernel.org, linux-arm-kernel at lists.infradead.org,
+ Viresh Kumar <viresh.kumar at linaro.org>,
+ Mark Rutland <mark.rutland at arm.com>, Russell King <linux at arm.linux.org.uk>,
+ Courtney Cavin <courtney.cavin at sonymobile.com>
+Date: Fri, 20 Mar 2015 23:45:20 -0700
+
+Krait CPUs have a handful of L2 cache controller registers that
+live behind a cp15 based indirection register. First you program
+the indirection register (l2cpselr) to point the L2 'window'
+register (l2cpdr) at what you want to read/write. Then you
+read/write the 'window' register to do what you want. The
+l2cpselr register is not banked per-cpu so we must lock around
+accesses to it to prevent other CPUs from re-pointing l2cpdr
+underneath us.
+
+Cc: Mark Rutland <mark.rutland at arm.com>
+Cc: Russell King <linux at arm.linux.org.uk>
+Cc: Courtney Cavin <courtney.cavin at sonymobile.com>
+Signed-off-by: Stephen Boyd <sboyd at codeaurora.org>
+
+---
+arch/arm/common/Kconfig | 3 ++
+ arch/arm/common/Makefile | 1 +
+ arch/arm/common/krait-l2-accessors.c | 58 +++++++++++++++++++++++++++++++
+ arch/arm/include/asm/krait-l2-accessors.h | 20 +++++++++++
+ 4 files changed, 82 insertions(+)
+ create mode 100644 arch/arm/common/krait-l2-accessors.c
+ create mode 100644 arch/arm/include/asm/krait-l2-accessors.h
+
+--- a/arch/arm/common/Kconfig
++++ b/arch/arm/common/Kconfig
+@@ -9,6 +9,9 @@ config DMABOUNCE
+ bool
+ select ZONE_DMA
+
++config KRAIT_L2_ACCESSORS
++ bool
++
+ config SHARP_LOCOMO
+ bool
+
+--- a/arch/arm/common/Makefile
++++ b/arch/arm/common/Makefile
+@@ -7,6 +7,7 @@ obj-y += firmware.o
+ obj-$(CONFIG_ICST) += icst.o
+ obj-$(CONFIG_SA1111) += sa1111.o
+ obj-$(CONFIG_DMABOUNCE) += dmabounce.o
++obj-$(CONFIG_KRAIT_L2_ACCESSORS) += krait-l2-accessors.o
+ obj-$(CONFIG_SHARP_LOCOMO) += locomo.o
+ obj-$(CONFIG_SHARP_PARAM) += sharpsl_param.o
+ obj-$(CONFIG_SHARP_SCOOP) += scoop.o
+--- /dev/null
++++ b/arch/arm/common/krait-l2-accessors.c
+@@ -0,0 +1,58 @@
++/*
++ * Copyright (c) 2011-2013, The Linux Foundation. All rights reserved.
++ *
++ * This program is free software; you can redistribute it and/or modify
++ * it under the terms of the GNU General Public License version 2 and
++ * only version 2 as published by the Free Software Foundation.
++ *
++ * This program is distributed in the hope that it will be useful,
++ * but WITHOUT ANY WARRANTY; without even the implied warranty of
++ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
++ * GNU General Public License for more details.
++ */
++
++#include <linux/spinlock.h>
++#include <linux/export.h>
++
++#include <asm/barrier.h>
++#include <asm/krait-l2-accessors.h>
++
++static DEFINE_RAW_SPINLOCK(krait_l2_lock);
++
++void krait_set_l2_indirect_reg(u32 addr, u32 val)
++{
++ unsigned long flags;
++
++ raw_spin_lock_irqsave(&krait_l2_lock, flags);
++ /*
++ * Select the L2 window by poking l2cpselr, then write to the window
++ * via l2cpdr.
++ */
++ asm volatile ("mcr p15, 3, %0, c15, c0, 6 @ l2cpselr" : : "r" (addr));
++ isb();
++ asm volatile ("mcr p15, 3, %0, c15, c0, 7 @ l2cpdr" : : "r" (val));
++ isb();
++
++ raw_spin_unlock_irqrestore(&krait_l2_lock, flags);
++}
++EXPORT_SYMBOL(krait_set_l2_indirect_reg);
++
++u32 krait_get_l2_indirect_reg(u32 addr)
++{
++ u32 val;
++ unsigned long flags;
++
++ raw_spin_lock_irqsave(&krait_l2_lock, flags);
++ /*
++ * Select the L2 window by poking l2cpselr, then read from the window
++ * via l2cpdr.
++ */
++ asm volatile ("mcr p15, 3, %0, c15, c0, 6 @ l2cpselr" : : "r" (addr));
++ isb();
++ asm volatile ("mrc p15, 3, %0, c15, c0, 7 @ l2cpdr" : "=r" (val));
++
++ raw_spin_unlock_irqrestore(&krait_l2_lock, flags);
++
++ return val;
++}
++EXPORT_SYMBOL(krait_get_l2_indirect_reg);
+--- /dev/null
++++ b/arch/arm/include/asm/krait-l2-accessors.h
+@@ -0,0 +1,20 @@
++/*
++ * Copyright (c) 2011-2013, The Linux Foundation. All rights reserved.
++ *
++ * This program is free software; you can redistribute it and/or modify
++ * it under the terms of the GNU General Public License version 2 and
++ * only version 2 as published by the Free Software Foundation.
++ *
++ * This program is distributed in the hope that it will be useful,
++ * but WITHOUT ANY WARRANTY; without even the implied warranty of
++ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
++ * GNU General Public License for more details.
++ */
++
++#ifndef __ASMARM_KRAIT_L2_ACCESSORS_H
++#define __ASMARM_KRAIT_L2_ACCESSORS_H
++
++extern void krait_set_l2_indirect_reg(u32 addr, u32 val);
++extern u32 krait_get_l2_indirect_reg(u32 addr);
++
++#endif
diff --git a/target/linux/ipq806x/patches-4.0/134-clk-mux-Split-out-register-accessors-for-reuse.patch b/target/linux/ipq806x/patches-4.0/134-clk-mux-Split-out-register-accessors-for-reuse.patch
new file mode 100644
index 0000000..3a475fb
--- /dev/null
+++ b/target/linux/ipq806x/patches-4.0/134-clk-mux-Split-out-register-accessors-for-reuse.patch
@@ -0,0 +1,192 @@
+Content-Type: text/plain; charset="utf-8"
+MIME-Version: 1.0
+Content-Transfer-Encoding: 7bit
+Subject: [v3,02/13] clk: mux: Split out register accessors for reuse
+From: Stephen Boyd <sboyd at codeaurora.org>
+X-Patchwork-Id: 6063111
+Message-Id: <1426920332-9340-3-git-send-email-sboyd at codeaurora.org>
+To: Mike Turquette <mturquette at linaro.org>, Stephen Boyd <sboyd at codeaurora.org>
+Cc: linux-kernel at vger.kernel.org, linux-arm-msm at vger.kernel.org,
+ linux-pm at vger.kernel.org, linux-arm-kernel at lists.infradead.org,
+ Viresh Kumar <viresh.kumar at linaro.org>
+Date: Fri, 20 Mar 2015 23:45:21 -0700
+
+We want to reuse the logic in clk-mux.c for other clock drivers
+that don't use readl as register accessors. Fortunately, there
+really isn't much to the mux code besides the table indirection
+and quirk flags if you assume any bit shifting and masking has
+been done already. Pull that logic out into reusable functions
+that operate on an optional table and some flags so that other
+drivers can use the same logic.
+
+Signed-off-by: Stephen Boyd <sboyd at codeaurora.org>
+
+---
+drivers/clk/clk-mux.c | 76 +++++++++++++++++++++++++++-----------------
+ include/linux/clk-provider.h | 9 ++++--
+ 2 files changed, 54 insertions(+), 31 deletions(-)
+
+--- a/drivers/clk/clk-mux.c
++++ b/drivers/clk/clk-mux.c
+@@ -29,35 +29,24 @@
+
+ #define to_clk_mux(_hw) container_of(_hw, struct clk_mux, hw)
+
+-static u8 clk_mux_get_parent(struct clk_hw *hw)
++unsigned int clk_mux_get_parent(struct clk_hw *hw, unsigned int val,
++ unsigned int *table, unsigned long flags)
+ {
+- struct clk_mux *mux = to_clk_mux(hw);
+ int num_parents = __clk_get_num_parents(hw->clk);
+- u32 val;
+
+- /*
+- * FIXME need a mux-specific flag to determine if val is bitwise or numeric
+- * e.g. sys_clkin_ck's clksel field is 3 bits wide, but ranges from 0x1
+- * to 0x7 (index starts at one)
+- * OTOH, pmd_trace_clk_mux_ck uses a separate bit for each clock, so
+- * val = 0x4 really means "bit 2, index starts at bit 0"
+- */
+- val = clk_readl(mux->reg) >> mux->shift;
+- val &= mux->mask;
+-
+- if (mux->table) {
++ if (table) {
+ int i;
+
+ for (i = 0; i < num_parents; i++)
+- if (mux->table[i] == val)
++ if (table[i] == val)
+ return i;
+ return -EINVAL;
+ }
+
+- if (val && (mux->flags & CLK_MUX_INDEX_BIT))
++ if (val && (flags & CLK_MUX_INDEX_BIT))
+ val = ffs(val) - 1;
+
+- if (val && (mux->flags & CLK_MUX_INDEX_ONE))
++ if (val && (flags & CLK_MUX_INDEX_ONE))
+ val--;
+
+ if (val >= num_parents)
+@@ -65,24 +54,53 @@ static u8 clk_mux_get_parent(struct clk_
+
+ return val;
+ }
++EXPORT_SYMBOL_GPL(clk_mux_get_parent);
+
+-static int clk_mux_set_parent(struct clk_hw *hw, u8 index)
++static u8 _clk_mux_get_parent(struct clk_hw *hw)
+ {
+ struct clk_mux *mux = to_clk_mux(hw);
+ u32 val;
+- unsigned long flags = 0;
+
+- if (mux->table)
+- index = mux->table[index];
++ /*
++ * FIXME need a mux-specific flag to determine if val is bitwise or numeric
++ * e.g. sys_clkin_ck's clksel field is 3 bits wide, but ranges from 0x1
++ * to 0x7 (index starts at one)
++ * OTOH, pmd_trace_clk_mux_ck uses a separate bit for each clock, so
++ * val = 0x4 really means "bit 2, index starts at bit 0"
++ */
++ val = clk_readl(mux->reg) >> mux->shift;
++ val &= mux->mask;
++
++ return clk_mux_get_parent(hw, val, mux->table, mux->flags);
++}
+
+- else {
+- if (mux->flags & CLK_MUX_INDEX_BIT)
+- index = 1 << index;
++unsigned int clk_mux_reindex(u8 index, unsigned int *table,
++ unsigned long flags)
++{
++ unsigned int val = index;
+
+- if (mux->flags & CLK_MUX_INDEX_ONE)
+- index++;
++ if (table) {
++ val = table[val];
++ } else {
++ if (flags & CLK_MUX_INDEX_BIT)
++ val = 1 << index;
++
++ if (flags & CLK_MUX_INDEX_ONE)
++ val++;
+ }
+
++ return val;
++}
++EXPORT_SYMBOL_GPL(clk_mux_reindex);
++
++static int clk_mux_set_parent(struct clk_hw *hw, u8 index)
++{
++ struct clk_mux *mux = to_clk_mux(hw);
++ u32 val;
++ unsigned long flags = 0;
++
++ index = clk_mux_reindex(index, mux->table, mux->flags);
++
+ if (mux->lock)
+ spin_lock_irqsave(mux->lock, flags);
+
+@@ -102,21 +120,21 @@ static int clk_mux_set_parent(struct clk
+ }
+
+ const struct clk_ops clk_mux_ops = {
+- .get_parent = clk_mux_get_parent,
++ .get_parent = _clk_mux_get_parent,
+ .set_parent = clk_mux_set_parent,
+ .determine_rate = __clk_mux_determine_rate,
+ };
+ EXPORT_SYMBOL_GPL(clk_mux_ops);
+
+ const struct clk_ops clk_mux_ro_ops = {
+- .get_parent = clk_mux_get_parent,
++ .get_parent = _clk_mux_get_parent,
+ };
+ EXPORT_SYMBOL_GPL(clk_mux_ro_ops);
+
+ struct clk *clk_register_mux_table(struct device *dev, const char *name,
+ const char **parent_names, u8 num_parents, unsigned long flags,
+ void __iomem *reg, u8 shift, u32 mask,
+- u8 clk_mux_flags, u32 *table, spinlock_t *lock)
++ u8 clk_mux_flags, unsigned int *table, spinlock_t *lock)
+ {
+ struct clk_mux *mux;
+ struct clk *clk;
+--- a/include/linux/clk-provider.h
++++ b/include/linux/clk-provider.h
+@@ -409,7 +409,7 @@ void clk_unregister_divider(struct clk *
+ struct clk_mux {
+ struct clk_hw hw;
+ void __iomem *reg;
+- u32 *table;
++ unsigned int *table;
+ u32 mask;
+ u8 shift;
+ u8 flags;
+@@ -425,6 +425,11 @@ struct clk_mux {
+ extern const struct clk_ops clk_mux_ops;
+ extern const struct clk_ops clk_mux_ro_ops;
+
++unsigned int clk_mux_get_parent(struct clk_hw *hw, unsigned int val,
++ unsigned int *table, unsigned long flags);
++unsigned int clk_mux_reindex(u8 index, unsigned int *table,
++ unsigned long flags);
++
+ struct clk *clk_register_mux(struct device *dev, const char *name,
+ const char **parent_names, u8 num_parents, unsigned long flags,
+ void __iomem *reg, u8 shift, u8 width,
+@@ -433,7 +438,7 @@ struct clk *clk_register_mux(struct devi
+ struct clk *clk_register_mux_table(struct device *dev, const char *name,
+ const char **parent_names, u8 num_parents, unsigned long flags,
+ void __iomem *reg, u8 shift, u32 mask,
+- u8 clk_mux_flags, u32 *table, spinlock_t *lock);
++ u8 clk_mux_flags, unsigned int *table, spinlock_t *lock);
+
+ void clk_unregister_mux(struct clk *clk);
+
diff --git a/target/linux/ipq806x/patches-4.0/135-clk-Avoid-sending-high-rates-to-downstream-clocks-during-set_rate.patch b/target/linux/ipq806x/patches-4.0/135-clk-Avoid-sending-high-rates-to-downstream-clocks-during-set_rate.patch
new file mode 100644
index 0000000..f699521
--- /dev/null
+++ b/target/linux/ipq806x/patches-4.0/135-clk-Avoid-sending-high-rates-to-downstream-clocks-during-set_rate.patch
@@ -0,0 +1,130 @@
+Content-Type: text/plain; charset="utf-8"
+MIME-Version: 1.0
+Content-Transfer-Encoding: 7bit
+Subject: [v3, 03/13] clk: Avoid sending high rates to downstream clocks during
+ set_rate
+From: Stephen Boyd <sboyd at codeaurora.org>
+X-Patchwork-Id: 6063271
+Message-Id: <1426920332-9340-4-git-send-email-sboyd at codeaurora.org>
+To: Mike Turquette <mturquette at linaro.org>, Stephen Boyd <sboyd at codeaurora.org>
+Cc: linux-kernel at vger.kernel.org, linux-arm-msm at vger.kernel.org,
+ linux-pm at vger.kernel.org, linux-arm-kernel at lists.infradead.org,
+ Viresh Kumar <viresh.kumar at linaro.org>
+Date: Fri, 20 Mar 2015 23:45:22 -0700
+
+If a clock is on and we call clk_set_rate() on it we may get into
+a situation where the clock temporarily increases in rate
+dramatically while we walk the tree and call .set_rate() ops. For
+example, consider a case where a PLL feeds into a divider.
+Initially the divider is set to divide by 1 and the PLL is
+running fairly slow (100MHz). The downstream consumer of the
+divider output can only handle rates =< 400 MHz, but the divider
+can only choose between divisors of 1 and 4.
+
+ +-----+ +----------------+
+ | PLL |-->| div 1 or div 4 |---> consumer device
+ +-----+ +----------------+
+
+To achieve a rate of 400MHz on the output of the divider, we
+would have to set the rate of the PLL to 1.6 GHz and then divide
+it by 4. The current code would set the PLL to 1.6GHz first while
+the divider is still set to 1, thus causing the downstream
+consumer of the clock to receive a few clock cycles of 1.6GHz
+clock (far beyond it's maximum acceptable rate). We should be
+changing the divider first before increasing the PLL rate to
+avoid this problem.
+
+Therefore, set the rate of any child clocks that are increasing
+in rate from their current rate so that they can increase their
+dividers if necessary. We assume that there isn't such a thing as
+minimum rate requirements.
+
+Signed-off-by: Stephen Boyd <sboyd at codeaurora.org>
+
+---
+drivers/clk/clk.c | 34 ++++++++++++++++++++++------------
+ 1 file changed, 22 insertions(+), 12 deletions(-)
+
+--- a/drivers/clk/clk.c
++++ b/drivers/clk/clk.c
+@@ -1688,21 +1688,24 @@ static struct clk_core *clk_propagate_ra
+ * walk down a subtree and set the new rates notifying the rate
+ * change on the way
+ */
+-static void clk_change_rate(struct clk_core *clk)
++static void
++clk_change_rate(struct clk_core *clk, unsigned long best_parent_rate)
+ {
+ struct clk_core *child;
+ struct hlist_node *tmp;
+ unsigned long old_rate;
+- unsigned long best_parent_rate = 0;
+ bool skip_set_rate = false;
+ struct clk_core *old_parent;
+
+- old_rate = clk->rate;
++ hlist_for_each_entry(child, &clk->children, child_node) {
++ /* Skip children who will be reparented to another clock */
++ if (child->new_parent && child->new_parent != clk)
++ continue;
++ if (child->new_rate > child->rate)
++ clk_change_rate(child, clk->new_rate);
++ }
+
+- if (clk->new_parent)
+- best_parent_rate = clk->new_parent->rate;
+- else if (clk->parent)
+- best_parent_rate = clk->parent->rate;
++ old_rate = clk->rate;
+
+ if (clk->new_parent && clk->new_parent != clk->parent) {
+ old_parent = __clk_set_parent_before(clk, clk->new_parent);
+@@ -1722,7 +1725,7 @@ static void clk_change_rate(struct clk_c
+ if (!skip_set_rate && clk->ops->set_rate)
+ clk->ops->set_rate(clk->hw, clk->new_rate, best_parent_rate);
+
+- clk->rate = clk_recalc(clk, best_parent_rate);
++ clk->rate = clk->new_rate;
+
+ if (clk->notifier_count && old_rate != clk->rate)
+ __clk_notify(clk, POST_RATE_CHANGE, old_rate, clk->rate);
+@@ -1735,12 +1738,13 @@ static void clk_change_rate(struct clk_c
+ /* Skip children who will be reparented to another clock */
+ if (child->new_parent && child->new_parent != clk)
+ continue;
+- clk_change_rate(child);
++ if (child->new_rate != child->rate)
++ clk_change_rate(child, clk->new_rate);
+ }
+
+ /* handle the new child who might not be in clk->children yet */
+- if (clk->new_child)
+- clk_change_rate(clk->new_child);
++ if (clk->new_child && clk->new_child->new_rate != clk->new_child->rate)
++ clk_change_rate(clk->new_child, clk->new_rate);
+ }
+
+ static int clk_core_set_rate_nolock(struct clk_core *clk,
+@@ -1749,6 +1753,7 @@ static int clk_core_set_rate_nolock(stru
+ struct clk_core *top, *fail_clk;
+ unsigned long rate = req_rate;
+ int ret = 0;
++ unsigned long parent_rate;
+
+ if (!clk)
+ return 0;
+@@ -1774,8 +1779,13 @@ static int clk_core_set_rate_nolock(stru
+ return -EBUSY;
+ }
+
++ if (top->parent)
++ parent_rate = top->parent->rate;
++ else
++ parent_rate = 0;
++
+ /* change the rates */
+- clk_change_rate(top);
++ clk_change_rate(top, parent_rate);
+
+ clk->req_rate = req_rate;
+
diff --git a/target/linux/ipq806x/patches-4.0/136-clk-Add-safe-switch-hook.patch b/target/linux/ipq806x/patches-4.0/136-clk-Add-safe-switch-hook.patch
new file mode 100644
index 0000000..d3363f84
--- /dev/null
+++ b/target/linux/ipq806x/patches-4.0/136-clk-Add-safe-switch-hook.patch
@@ -0,0 +1,164 @@
+Content-Type: text/plain; charset="utf-8"
+MIME-Version: 1.0
+Content-Transfer-Encoding: 7bit
+Subject: [v3,04/13] clk: Add safe switch hook
+From: Stephen Boyd <sboyd at codeaurora.org>
+X-Patchwork-Id: 6063211
+Message-Id: <1426920332-9340-5-git-send-email-sboyd at codeaurora.org>
+To: Mike Turquette <mturquette at linaro.org>, Stephen Boyd <sboyd at codeaurora.org>
+Cc: linux-kernel at vger.kernel.org, linux-arm-msm at vger.kernel.org,
+ linux-pm at vger.kernel.org, linux-arm-kernel at lists.infradead.org,
+ Viresh Kumar <viresh.kumar at linaro.org>
+Date: Fri, 20 Mar 2015 23:45:23 -0700
+
+Sometimes clocks can't accept their parent source turning off
+while the source is reprogrammed to a different rate. Most
+notably CPU clocks require a way to switch away from the current
+PLL they're running on, reprogram that PLL to a new rate, and
+then switch back to the PLL with the new rate once they're done.
+Add a hook that drivers can implement allowing them to return a
+'safe parent' that they can switch their parent to while the
+upstream source is reprogrammed to support this.
+
+Signed-off-by: Stephen Boyd <sboyd at codeaurora.org>
+
+---
+This patch is good enough for Krait, but soon I'll need to
+support a "safe rate" where we ask a clock what rate it needs to be running
+at to be sure it's within voltage constraints. Right now safe parent
+handles that problem on Krait, but on other platforms it won't work.
+
+ drivers/clk/clk.c | 61 ++++++++++++++++++++++++++++++++++++++------
+ include/linux/clk-provider.h | 1 +
+ 2 files changed, 54 insertions(+), 8 deletions(-)
+
+--- a/drivers/clk/clk.c
++++ b/drivers/clk/clk.c
+@@ -56,9 +56,12 @@ struct clk_core {
+ struct clk_core **parents;
+ u8 num_parents;
+ u8 new_parent_index;
++ u8 safe_parent_index;
+ unsigned long rate;
+ unsigned long req_rate;
++ unsigned long old_rate;
+ unsigned long new_rate;
++ struct clk_core *safe_parent;
+ struct clk_core *new_parent;
+ struct clk_core *new_child;
+ unsigned long flags;
+@@ -1549,7 +1552,8 @@ out:
+ static void clk_calc_subtree(struct clk_core *clk, unsigned long new_rate,
+ struct clk_core *new_parent, u8 p_index)
+ {
+- struct clk_core *child;
++ struct clk_core *child, *parent;
++ struct clk_hw *parent_hw;
+
+ clk->new_rate = new_rate;
+ clk->new_parent = new_parent;
+@@ -1559,6 +1563,18 @@ static void clk_calc_subtree(struct clk_
+ if (new_parent && new_parent != clk->parent)
+ new_parent->new_child = clk;
+
++ if (clk->ops->get_safe_parent) {
++ parent_hw = clk->ops->get_safe_parent(clk->hw);
++ if (parent_hw) {
++ parent = parent_hw->core;
++ p_index = clk_fetch_parent_index(clk, parent);
++ clk->safe_parent_index = p_index;
++ clk->safe_parent = parent;
++ }
++ } else {
++ clk->safe_parent = NULL;
++ }
++
+ hlist_for_each_entry(child, &clk->children, child_node) {
+ child->new_rate = clk_recalc(child, new_rate);
+ clk_calc_subtree(child, child->new_rate, NULL, 0);
+@@ -1654,14 +1670,43 @@ static struct clk_core *clk_propagate_ra
+ unsigned long event)
+ {
+ struct clk_core *child, *tmp_clk, *fail_clk = NULL;
++ struct clk_core *old_parent;
+ int ret = NOTIFY_DONE;
+
+- if (clk->rate == clk->new_rate)
++ if (clk->rate == clk->new_rate && event != POST_RATE_CHANGE)
+ return NULL;
+
++ switch (event) {
++ case PRE_RATE_CHANGE:
++ if (clk->safe_parent)
++ clk->ops->set_parent(clk->hw, clk->safe_parent_index);
++ clk->old_rate = clk->rate;
++ break;
++ case POST_RATE_CHANGE:
++ if (clk->safe_parent) {
++ old_parent = __clk_set_parent_before(clk,
++ clk->new_parent);
++ if (clk->ops->set_rate_and_parent) {
++ clk->ops->set_rate_and_parent(clk->hw,
++ clk->new_rate,
++ clk->new_parent ?
++ clk->new_parent->rate : 0,
++ clk->new_parent_index);
++ } else if (clk->ops->set_parent) {
++ clk->ops->set_parent(clk->hw,
++ clk->new_parent_index);
++ }
++ __clk_set_parent_after(clk, clk->new_parent,
++ old_parent);
++ }
++ break;
++ }
++
+ if (clk->notifier_count) {
+- ret = __clk_notify(clk, event, clk->rate, clk->new_rate);
+- if (ret & NOTIFY_STOP_MASK)
++ if (event != POST_RATE_CHANGE || clk->old_rate != clk->rate)
++ ret = __clk_notify(clk, event, clk->old_rate,
++ clk->new_rate);
++ if (ret & NOTIFY_STOP_MASK && event != POST_RATE_CHANGE)
+ fail_clk = clk;
+ }
+
+@@ -1707,7 +1752,8 @@ clk_change_rate(struct clk_core *clk, un
+
+ old_rate = clk->rate;
+
+- if (clk->new_parent && clk->new_parent != clk->parent) {
++ if (clk->new_parent && clk->new_parent != clk->parent &&
++ !clk->safe_parent) {
+ old_parent = __clk_set_parent_before(clk, clk->new_parent);
+
+ if (clk->ops->set_rate_and_parent) {
+@@ -1727,9 +1773,6 @@ clk_change_rate(struct clk_core *clk, un
+
+ clk->rate = clk->new_rate;
+
+- if (clk->notifier_count && old_rate != clk->rate)
+- __clk_notify(clk, POST_RATE_CHANGE, old_rate, clk->rate);
+-
+ /*
+ * Use safe iteration, as change_rate can actually swap parents
+ * for certain clock types.
+@@ -1789,6 +1832,8 @@ static int clk_core_set_rate_nolock(stru
+
+ clk->req_rate = req_rate;
+
++ clk_propagate_rate_change(top, POST_RATE_CHANGE);
++
+ return ret;
+ }
+
+--- a/include/linux/clk-provider.h
++++ b/include/linux/clk-provider.h
+@@ -183,6 +183,7 @@ struct clk_ops {
+ struct clk_hw **best_parent_hw);
+ int (*set_parent)(struct clk_hw *hw, u8 index);
+ u8 (*get_parent)(struct clk_hw *hw);
++ struct clk_hw *(*get_safe_parent)(struct clk_hw *hw);
+ int (*set_rate)(struct clk_hw *hw, unsigned long rate,
+ unsigned long parent_rate);
+ int (*set_rate_and_parent)(struct clk_hw *hw,
diff --git a/target/linux/ipq806x/patches-4.0/137-clk-qcom-Add-support-for-High-Frequency-PLLs-HFPLLs.patch b/target/linux/ipq806x/patches-4.0/137-clk-qcom-Add-support-for-High-Frequency-PLLs-HFPLLs.patch
new file mode 100644
index 0000000..6fad6e8
--- /dev/null
+++ b/target/linux/ipq806x/patches-4.0/137-clk-qcom-Add-support-for-High-Frequency-PLLs-HFPLLs.patch
@@ -0,0 +1,351 @@
+Content-Type: text/plain; charset="utf-8"
+MIME-Version: 1.0
+Content-Transfer-Encoding: 7bit
+Subject: [v3,05/13] clk: qcom: Add support for High-Frequency PLLs (HFPLLs)
+From: Stephen Boyd <sboyd at codeaurora.org>
+X-Patchwork-Id: 6063261
+Message-Id: <1426920332-9340-6-git-send-email-sboyd at codeaurora.org>
+To: Mike Turquette <mturquette at linaro.org>, Stephen Boyd <sboyd at codeaurora.org>
+Cc: linux-kernel at vger.kernel.org, linux-arm-msm at vger.kernel.org,
+ linux-pm at vger.kernel.org, linux-arm-kernel at lists.infradead.org,
+ Viresh Kumar <viresh.kumar at linaro.org>
+Date: Fri, 20 Mar 2015 23:45:24 -0700
+
+HFPLLs are the main frequency source for Krait CPU clocks. Add
+support for changing the rate of these PLLs.
+
+Signed-off-by: Stephen Boyd <sboyd at codeaurora.org>
+
+---
+I'd really like to get rid of __clk_hfpll_init_once() if possible...
+
+ drivers/clk/qcom/Makefile | 1 +
+ drivers/clk/qcom/clk-hfpll.c | 253 +++++++++++++++++++++++++++++++++++++++++++
+ drivers/clk/qcom/clk-hfpll.h | 54 +++++++++
+ 3 files changed, 308 insertions(+)
+ create mode 100644 drivers/clk/qcom/clk-hfpll.c
+ create mode 100644 drivers/clk/qcom/clk-hfpll.h
+
+--- a/drivers/clk/qcom/Makefile
++++ b/drivers/clk/qcom/Makefile
+@@ -8,6 +8,7 @@ clk-qcom-y += clk-rcg2.o
+ clk-qcom-y += clk-branch.o
+ clk-qcom-y += clk-regmap-divider.o
+ clk-qcom-y += clk-regmap-mux.o
++clk-qcom-y += clk-hfpll.o
+ clk-qcom-y += reset.o
+
+ obj-$(CONFIG_APQ_GCC_8084) += gcc-apq8084.o
+--- /dev/null
++++ b/drivers/clk/qcom/clk-hfpll.c
+@@ -0,0 +1,253 @@
++/*
++ * Copyright (c) 2013-2014, The Linux Foundation. All rights reserved.
++ *
++ * This program is free software; you can redistribute it and/or modify
++ * it under the terms of the GNU General Public License version 2 and
++ * only version 2 as published by the Free Software Foundation.
++ *
++ * This program is distributed in the hope that it will be useful,
++ * but WITHOUT ANY WARRANTY; without even the implied warranty of
++ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
++ * GNU General Public License for more details.
++ */
++#include <linux/kernel.h>
++#include <linux/export.h>
++#include <linux/regmap.h>
++#include <linux/delay.h>
++#include <linux/err.h>
++#include <linux/clk-provider.h>
++#include <linux/spinlock.h>
++
++#include "clk-regmap.h"
++#include "clk-hfpll.h"
++
++#define PLL_OUTCTRL BIT(0)
++#define PLL_BYPASSNL BIT(1)
++#define PLL_RESET_N BIT(2)
++
++/* Initialize a HFPLL at a given rate and enable it. */
++static void __clk_hfpll_init_once(struct clk_hw *hw)
++{
++ struct clk_hfpll *h = to_clk_hfpll(hw);
++ struct hfpll_data const *hd = h->d;
++ struct regmap *regmap = h->clkr.regmap;
++
++ if (likely(h->init_done))
++ return;
++
++ /* Configure PLL parameters for integer mode. */
++ if (hd->config_val)
++ regmap_write(regmap, hd->config_reg, hd->config_val);
++ regmap_write(regmap, hd->m_reg, 0);
++ regmap_write(regmap, hd->n_reg, 1);
++
++ if (hd->user_reg) {
++ u32 regval = hd->user_val;
++ unsigned long rate;
++
++ rate = __clk_get_rate(hw->clk);
++
++ /* Pick the right VCO. */
++ if (hd->user_vco_mask && rate > hd->low_vco_max_rate)
++ regval |= hd->user_vco_mask;
++ regmap_write(regmap, hd->user_reg, regval);
++ }
++
++ if (hd->droop_reg)
++ regmap_write(regmap, hd->droop_reg, hd->droop_val);
++
++ h->init_done = true;
++}
++
++static void __clk_hfpll_enable(struct clk_hw *hw)
++{
++ struct clk_hfpll *h = to_clk_hfpll(hw);
++ struct hfpll_data const *hd = h->d;
++ struct regmap *regmap = h->clkr.regmap;
++ u32 val;
++
++ __clk_hfpll_init_once(hw);
++
++ /* Disable PLL bypass mode. */
++ regmap_update_bits(regmap, hd->mode_reg, PLL_BYPASSNL, PLL_BYPASSNL);
++
++ /*
++ * H/W requires a 5us delay between disabling the bypass and
++ * de-asserting the reset. Delay 10us just to be safe.
++ */
++ udelay(10);
++
++ /* De-assert active-low PLL reset. */
++ regmap_update_bits(regmap, hd->mode_reg, PLL_RESET_N, PLL_RESET_N);
++
++ /* Wait for PLL to lock. */
++ if (hd->status_reg) {
++ do {
++ regmap_read(regmap, hd->status_reg, &val);
++ } while (!(val & BIT(hd->lock_bit)));
++ } else {
++ udelay(60);
++ }
++
++ /* Enable PLL output. */
++ regmap_update_bits(regmap, hd->mode_reg, PLL_OUTCTRL, PLL_OUTCTRL);
++}
++
++/* Enable an already-configured HFPLL. */
++static int clk_hfpll_enable(struct clk_hw *hw)
++{
++ unsigned long flags;
++ struct clk_hfpll *h = to_clk_hfpll(hw);
++ struct hfpll_data const *hd = h->d;
++ struct regmap *regmap = h->clkr.regmap;
++ u32 mode;
++
++ spin_lock_irqsave(&h->lock, flags);
++ regmap_read(regmap, hd->mode_reg, &mode);
++ if (!(mode & (PLL_BYPASSNL | PLL_RESET_N | PLL_OUTCTRL)))
++ __clk_hfpll_enable(hw);
++ spin_unlock_irqrestore(&h->lock, flags);
++
++ return 0;
++}
++
++static void __clk_hfpll_disable(struct clk_hfpll *h)
++{
++ struct hfpll_data const *hd = h->d;
++ struct regmap *regmap = h->clkr.regmap;
++
++ /*
++ * Disable the PLL output, disable test mode, enable the bypass mode,
++ * and assert the reset.
++ */
++ regmap_update_bits(regmap, hd->mode_reg,
++ PLL_BYPASSNL | PLL_RESET_N | PLL_OUTCTRL, 0);
++}
++
++static void clk_hfpll_disable(struct clk_hw *hw)
++{
++ struct clk_hfpll *h = to_clk_hfpll(hw);
++ unsigned long flags;
++
++ spin_lock_irqsave(&h->lock, flags);
++ __clk_hfpll_disable(h);
++ spin_unlock_irqrestore(&h->lock, flags);
++}
++
++static long clk_hfpll_round_rate(struct clk_hw *hw, unsigned long rate,
++ unsigned long *parent_rate)
++{
++ struct clk_hfpll *h = to_clk_hfpll(hw);
++ struct hfpll_data const *hd = h->d;
++ unsigned long rrate;
++
++ rate = clamp(rate, hd->min_rate, hd->max_rate);
++
++ rrate = DIV_ROUND_UP(rate, *parent_rate) * *parent_rate;
++ if (rrate > hd->max_rate)
++ rrate -= *parent_rate;
++
++ return rrate;
++}
++
++/*
++ * For optimization reasons, assumes no downstream clocks are actively using
++ * it.
++ */
++static int clk_hfpll_set_rate(struct clk_hw *hw, unsigned long rate,
++ unsigned long parent_rate)
++{
++ struct clk_hfpll *h = to_clk_hfpll(hw);
++ struct hfpll_data const *hd = h->d;
++ struct regmap *regmap = h->clkr.regmap;
++ unsigned long flags;
++ u32 l_val, val;
++ bool enabled;
++
++ l_val = rate / parent_rate;
++
++ spin_lock_irqsave(&h->lock, flags);
++
++ enabled = __clk_is_enabled(hw->clk);
++ if (enabled)
++ __clk_hfpll_disable(h);
++
++ /* Pick the right VCO. */
++ if (hd->user_reg && hd->user_vco_mask) {
++ regmap_read(regmap, hd->user_reg, &val);
++ if (rate <= hd->low_vco_max_rate)
++ val &= ~hd->user_vco_mask;
++ else
++ val |= hd->user_vco_mask;
++ regmap_write(regmap, hd->user_reg, val);
++ }
++
++ regmap_write(regmap, hd->l_reg, l_val);
++
++ if (enabled)
++ __clk_hfpll_enable(hw);
++
++ spin_unlock_irqrestore(&h->lock, flags);
++
++ return 0;
++}
++
++static unsigned long clk_hfpll_recalc_rate(struct clk_hw *hw,
++ unsigned long parent_rate)
++{
++ struct clk_hfpll *h = to_clk_hfpll(hw);
++ struct hfpll_data const *hd = h->d;
++ struct regmap *regmap = h->clkr.regmap;
++ u32 l_val;
++
++ regmap_read(regmap, hd->l_reg, &l_val);
++
++ return l_val * parent_rate;
++}
++
++static void clk_hfpll_init(struct clk_hw *hw)
++{
++ struct clk_hfpll *h = to_clk_hfpll(hw);
++ struct hfpll_data const *hd = h->d;
++ struct regmap *regmap = h->clkr.regmap;
++ u32 mode, status;
++
++ regmap_read(regmap, hd->mode_reg, &mode);
++ if (mode != (PLL_BYPASSNL | PLL_RESET_N | PLL_OUTCTRL)) {
++ __clk_hfpll_init_once(hw);
++ return;
++ }
++
++ if (hd->status_reg) {
++ regmap_read(regmap, hd->status_reg, &status);
++ if (!(status & BIT(hd->lock_bit))) {
++ WARN(1, "HFPLL %s is ON, but not locked!\n",
++ __clk_get_name(hw->clk));
++ clk_hfpll_disable(hw);
++ __clk_hfpll_init_once(hw);
++ }
++ }
++}
++
++static int hfpll_is_enabled(struct clk_hw *hw)
++{
++ struct clk_hfpll *h = to_clk_hfpll(hw);
++ struct hfpll_data const *hd = h->d;
++ struct regmap *regmap = h->clkr.regmap;
++ u32 mode;
++
++ regmap_read(regmap, hd->mode_reg, &mode);
++ mode &= 0x7;
++ return mode == (PLL_BYPASSNL | PLL_RESET_N | PLL_OUTCTRL);
++}
++
++const struct clk_ops clk_ops_hfpll = {
++ .enable = clk_hfpll_enable,
++ .disable = clk_hfpll_disable,
++ .is_enabled = hfpll_is_enabled,
++ .round_rate = clk_hfpll_round_rate,
++ .set_rate = clk_hfpll_set_rate,
++ .recalc_rate = clk_hfpll_recalc_rate,
++ .init = clk_hfpll_init,
++};
++EXPORT_SYMBOL_GPL(clk_ops_hfpll);
+--- /dev/null
++++ b/drivers/clk/qcom/clk-hfpll.h
+@@ -0,0 +1,54 @@
++/*
++ * Copyright (c) 2013-2014, The Linux Foundation. All rights reserved.
++ *
++ * This program is free software; you can redistribute it and/or modify
++ * it under the terms of the GNU General Public License version 2 and
++ * only version 2 as published by the Free Software Foundation.
++ *
++ * This program is distributed in the hope that it will be useful,
++ * but WITHOUT ANY WARRANTY; without even the implied warranty of
++ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
++ * GNU General Public License for more details.
++ */
++#ifndef __QCOM_CLK_HFPLL_H__
++#define __QCOM_CLK_HFPLL_H__
++
++#include <linux/clk-provider.h>
++#include <linux/spinlock.h>
++#include "clk-regmap.h"
++
++struct hfpll_data {
++ u32 mode_reg;
++ u32 l_reg;
++ u32 m_reg;
++ u32 n_reg;
++ u32 user_reg;
++ u32 droop_reg;
++ u32 config_reg;
++ u32 status_reg;
++ u8 lock_bit;
++
++ u32 droop_val;
++ u32 config_val;
++ u32 user_val;
++ u32 user_vco_mask;
++ unsigned long low_vco_max_rate;
++
++ unsigned long min_rate;
++ unsigned long max_rate;
++};
++
++struct clk_hfpll {
++ struct hfpll_data const *d;
++ int init_done;
++
++ struct clk_regmap clkr;
++ spinlock_t lock;
++};
++
++#define to_clk_hfpll(_hw) \
++ container_of(to_clk_regmap(_hw), struct clk_hfpll, clkr)
++
++extern const struct clk_ops clk_ops_hfpll;
++
++#endif
diff --git a/target/linux/ipq806x/patches-4.0/138-clk-qcom-Add-HFPLL-driver.patch b/target/linux/ipq806x/patches-4.0/138-clk-qcom-Add-HFPLL-driver.patch
new file mode 100644
index 0000000..b1f870a
--- /dev/null
+++ b/target/linux/ipq806x/patches-4.0/138-clk-qcom-Add-HFPLL-driver.patch
@@ -0,0 +1,206 @@
+Content-Type: text/plain; charset="utf-8"
+MIME-Version: 1.0
+Content-Transfer-Encoding: 7bit
+Subject: [v3,06/13] clk: qcom: Add HFPLL driver
+From: Stephen Boyd <sboyd at codeaurora.org>
+X-Patchwork-Id: 6063231
+Message-Id: <1426920332-9340-7-git-send-email-sboyd at codeaurora.org>
+To: Mike Turquette <mturquette at linaro.org>, Stephen Boyd <sboyd at codeaurora.org>
+Cc: linux-kernel at vger.kernel.org, linux-arm-msm at vger.kernel.org,
+ linux-pm at vger.kernel.org, linux-arm-kernel at lists.infradead.org,
+ Viresh Kumar <viresh.kumar at linaro.org>, <devicetree at vger.kernel.org>
+Date: Fri, 20 Mar 2015 23:45:25 -0700
+
+On some devices (MSM8974 for example), the HFPLLs are
+instantiated within the Krait processor subsystem as separate
+register regions. Add a driver for these PLLs so that we can
+provide HFPLL clocks for use by the system.
+
+Cc: <devicetree at vger.kernel.org>
+Signed-off-by: Stephen Boyd <sboyd at codeaurora.org>
+
+---
+.../devicetree/bindings/clock/qcom,hfpll.txt | 40 ++++++++
+ drivers/clk/qcom/Kconfig | 8 ++
+ drivers/clk/qcom/Makefile | 1 +
+ drivers/clk/qcom/hfpll.c | 109 +++++++++++++++++++++
+ 4 files changed, 158 insertions(+)
+ create mode 100644 Documentation/devicetree/bindings/clock/qcom,hfpll.txt
+ create mode 100644 drivers/clk/qcom/hfpll.c
+
+--- /dev/null
++++ b/Documentation/devicetree/bindings/clock/qcom,hfpll.txt
+@@ -0,0 +1,40 @@
++High-Frequency PLL (HFPLL)
++
++PROPERTIES
++
++- compatible:
++ Usage: required
++ Value type: <string>
++ Definition: must be "qcom,hfpll"
++
++- reg:
++ Usage: required
++ Value type: <prop-encoded-array>
++ Definition: address and size of HPLL registers. An optional second
++ element specifies the address and size of the alias
++ register region.
++
++- clock-output-names:
++ Usage: required
++ Value type: <string>
++ Definition: Name of the PLL. Typically hfpllX where X is a CPU number
++ starting at 0. Otherwise hfpll_Y where Y is more specific
++ such as "l2".
++
++Example:
++
++1) An HFPLL for the L2 cache.
++
++ clock-controller at f9016000 {
++ compatible = "qcom,hfpll";
++ reg = <0xf9016000 0x30>;
++ clock-output-names = "hfpll_l2";
++ };
++
++2) An HFPLL for CPU0. This HFPLL has the alias register region.
++
++ clock-controller at f908a000 {
++ compatible = "qcom,hfpll";
++ reg = <0xf908a000 0x30>, <0xf900a000 0x30>;
++ clock-output-names = "hfpll0";
++ };
+--- a/drivers/clk/qcom/Kconfig
++++ b/drivers/clk/qcom/Kconfig
+@@ -88,3 +88,11 @@ config MSM_MMCC_8974
+ Support for the multimedia clock controller on msm8974 devices.
+ Say Y if you want to support multimedia devices such as display,
+ graphics, video encode/decode, camera, etc.
++
++config QCOM_HFPLL
++ tristate "High-Frequency PLL (HFPLL) Clock Controller"
++ depends on COMMON_CLK_QCOM
++ help
++ Support for the high-frequency PLLs present on Qualcomm devices.
++ Say Y if you want to support CPU frequency scaling on devices
++ such as MSM8974, APQ8084, etc.
+--- a/drivers/clk/qcom/Makefile
++++ b/drivers/clk/qcom/Makefile
+@@ -21,3 +21,4 @@ obj-$(CONFIG_MSM_LCC_8960) += lcc-msm896
+ obj-$(CONFIG_MSM_GCC_8974) += gcc-msm8974.o
+ obj-$(CONFIG_MSM_MMCC_8960) += mmcc-msm8960.o
+ obj-$(CONFIG_MSM_MMCC_8974) += mmcc-msm8974.o
++obj-$(CONFIG_QCOM_HFPLL) += hfpll.o
+--- /dev/null
++++ b/drivers/clk/qcom/hfpll.c
+@@ -0,0 +1,109 @@
++/*
++ * Copyright (c) 2013-2014, The Linux Foundation. All rights reserved.
++ *
++ * This program is free software; you can redistribute it and/or modify
++ * it under the terms of the GNU General Public License version 2 and
++ * only version 2 as published by the Free Software Foundation.
++ *
++ * This program is distributed in the hope that it will be useful,
++ * but WITHOUT ANY WARRANTY; without even the implied warranty of
++ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
++ * GNU General Public License for more details.
++ */
++
++#include <linux/kernel.h>
++#include <linux/init.h>
++#include <linux/module.h>
++#include <linux/platform_device.h>
++#include <linux/of.h>
++#include <linux/clk.h>
++#include <linux/clk-provider.h>
++#include <linux/regmap.h>
++
++#include "clk-regmap.h"
++#include "clk-hfpll.h"
++
++static const struct hfpll_data hdata = {
++ .mode_reg = 0x00,
++ .l_reg = 0x04,
++ .m_reg = 0x08,
++ .n_reg = 0x0c,
++ .user_reg = 0x10,
++ .config_reg = 0x14,
++ .config_val = 0x430405d,
++ .status_reg = 0x1c,
++ .lock_bit = 16,
++
++ .user_val = 0x8,
++ .user_vco_mask = 0x100000,
++ .low_vco_max_rate = 1248000000,
++ .min_rate = 537600000UL,
++ .max_rate = 2900000000UL,
++};
++
++static const struct of_device_id qcom_hfpll_match_table[] = {
++ { .compatible = "qcom,hfpll" },
++ { }
++};
++MODULE_DEVICE_TABLE(of, qcom_hfpll_match_table);
++
++static const struct regmap_config hfpll_regmap_config = {
++ .reg_bits = 32,
++ .reg_stride = 4,
++ .val_bits = 32,
++ .max_register = 0x30,
++ .fast_io = true,
++};
++
++static int qcom_hfpll_probe(struct platform_device *pdev)
++{
++ struct clk *clk;
++ struct resource *res;
++ struct device *dev = &pdev->dev;
++ void __iomem *base;
++ struct regmap *regmap;
++ struct clk_hfpll *h;
++ struct clk_init_data init = {
++ .parent_names = (const char *[]){ "xo" },
++ .num_parents = 1,
++ .ops = &clk_ops_hfpll,
++ };
++
++ h = devm_kzalloc(dev, sizeof(*h), GFP_KERNEL);
++ if (!h)
++ return -ENOMEM;
++
++ res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
++ base = devm_ioremap_resource(dev, res);
++ if (IS_ERR(base))
++ return PTR_ERR(base);
++
++ regmap = devm_regmap_init_mmio(&pdev->dev, base, &hfpll_regmap_config);
++ if (IS_ERR(regmap))
++ return PTR_ERR(regmap);
++
++ if (of_property_read_string_index(dev->of_node, "clock-output-names",
++ 0, &init.name))
++ return -ENODEV;
++
++ h->d = &hdata;
++ h->clkr.hw.init = &init;
++ spin_lock_init(&h->lock);
++
++ clk = devm_clk_register_regmap(&pdev->dev, &h->clkr);
++
++ return PTR_ERR_OR_ZERO(clk);
++}
++
++static struct platform_driver qcom_hfpll_driver = {
++ .probe = qcom_hfpll_probe,
++ .driver = {
++ .name = "qcom-hfpll",
++ .of_match_table = qcom_hfpll_match_table,
++ },
++};
++module_platform_driver(qcom_hfpll_driver);
++
++MODULE_DESCRIPTION("QCOM HFPLL Clock Driver");
++MODULE_LICENSE("GPL v2");
++MODULE_ALIAS("platform:qcom-hfpll");
diff --git a/target/linux/ipq806x/patches-4.0/139-clk-qcom-Add-IPQ806X-s-HFPLLs.patch b/target/linux/ipq806x/patches-4.0/139-clk-qcom-Add-IPQ806X-s-HFPLLs.patch
new file mode 100644
index 0000000..d341006
--- /dev/null
+++ b/target/linux/ipq806x/patches-4.0/139-clk-qcom-Add-IPQ806X-s-HFPLLs.patch
@@ -0,0 +1,127 @@
+Content-Type: text/plain; charset="utf-8"
+MIME-Version: 1.0
+Content-Transfer-Encoding: 7bit
+Subject: [v3,08/13] clk: qcom: Add IPQ806X's HFPLLs
+From: Stephen Boyd <sboyd at codeaurora.org>
+X-Patchwork-Id: 6063241
+Message-Id: <1426920332-9340-9-git-send-email-sboyd at codeaurora.org>
+To: Mike Turquette <mturquette at linaro.org>, Stephen Boyd <sboyd at codeaurora.org>
+Cc: linux-kernel at vger.kernel.org, linux-arm-msm at vger.kernel.org,
+ linux-pm at vger.kernel.org, linux-arm-kernel at lists.infradead.org,
+ Viresh Kumar <viresh.kumar at linaro.org>
+Date: Fri, 20 Mar 2015 23:45:27 -0700
+
+Describe the HFPLLs present on IPQ806X devices.
+
+Signed-off-by: Stephen Boyd <sboyd at codeaurora.org>
+
+---
+drivers/clk/qcom/gcc-ipq806x.c | 83 ++++++++++++++++++++++++++++++++++++++++++
+ 1 file changed, 83 insertions(+)
+
+--- a/drivers/clk/qcom/gcc-ipq806x.c
++++ b/drivers/clk/qcom/gcc-ipq806x.c
+@@ -30,6 +30,7 @@
+ #include "clk-pll.h"
+ #include "clk-rcg.h"
+ #include "clk-branch.h"
++#include "clk-hfpll.h"
+ #include "reset.h"
+
+ static struct clk_pll pll0 = {
+@@ -113,6 +114,85 @@ static struct clk_regmap pll8_vote = {
+ },
+ };
+
++static struct hfpll_data hfpll0_data = {
++ .mode_reg = 0x3200,
++ .l_reg = 0x3208,
++ .m_reg = 0x320c,
++ .n_reg = 0x3210,
++ .config_reg = 0x3204,
++ .status_reg = 0x321c,
++ .config_val = 0x7845c665,
++ .droop_reg = 0x3214,
++ .droop_val = 0x0108c000,
++ .min_rate = 600000000UL,
++ .max_rate = 1800000000UL,
++};
++
++static struct clk_hfpll hfpll0 = {
++ .d = &hfpll0_data,
++ .clkr.hw.init = &(struct clk_init_data){
++ .parent_names = (const char *[]){ "pxo" },
++ .num_parents = 1,
++ .name = "hfpll0",
++ .ops = &clk_ops_hfpll,
++ .flags = CLK_IGNORE_UNUSED,
++ },
++ .lock = __SPIN_LOCK_UNLOCKED(hfpll0.lock),
++};
++
++static struct hfpll_data hfpll1_data = {
++ .mode_reg = 0x3240,
++ .l_reg = 0x3248,
++ .m_reg = 0x324c,
++ .n_reg = 0x3250,
++ .config_reg = 0x3244,
++ .status_reg = 0x325c,
++ .config_val = 0x7845c665,
++ .droop_reg = 0x3314,
++ .droop_val = 0x0108c000,
++ .min_rate = 600000000UL,
++ .max_rate = 1800000000UL,
++};
++
++static struct clk_hfpll hfpll1 = {
++ .d = &hfpll1_data,
++ .clkr.hw.init = &(struct clk_init_data){
++ .parent_names = (const char *[]){ "pxo" },
++ .num_parents = 1,
++ .name = "hfpll1",
++ .ops = &clk_ops_hfpll,
++ .flags = CLK_IGNORE_UNUSED,
++ },
++ .lock = __SPIN_LOCK_UNLOCKED(hfpll1.lock),
++};
++
++static struct hfpll_data hfpll_l2_data = {
++ .mode_reg = 0x3300,
++ .l_reg = 0x3308,
++ .m_reg = 0x330c,
++ .n_reg = 0x3310,
++ .config_reg = 0x3304,
++ .status_reg = 0x331c,
++ .config_val = 0x7845c665,
++ .droop_reg = 0x3314,
++ .droop_val = 0x0108c000,
++ .min_rate = 600000000UL,
++ .max_rate = 1800000000UL,
++};
++
++static struct clk_hfpll hfpll_l2 = {
++ .d = &hfpll_l2_data,
++ .clkr.hw.init = &(struct clk_init_data){
++ .parent_names = (const char *[]){ "pxo" },
++ .num_parents = 1,
++ .name = "hfpll_l2",
++ .ops = &clk_ops_hfpll,
++ .flags = CLK_IGNORE_UNUSED,
++ },
++ .lock = __SPIN_LOCK_UNLOCKED(hfpll_l2.lock),
++};
++
++
+ static struct clk_pll pll14 = {
+ .l_reg = 0x31c4,
+ .m_reg = 0x31c8,
+@@ -2273,6 +2353,9 @@ static struct clk_regmap *gcc_ipq806x_cl
+ [USB_FS1_XCVR_SRC] = &usb_fs1_xcvr_clk_src.clkr,
+ [USB_FS1_XCVR_CLK] = &usb_fs1_xcvr_clk.clkr,
+ [USB_FS1_SYSTEM_CLK] = &usb_fs1_sys_clk.clkr,
++ [PLL9] = &hfpll0.clkr,
++ [PLL10] = &hfpll1.clkr,
++ [PLL12] = &hfpll_l2.clkr,
+ };
+
+ static const struct qcom_reset_map gcc_ipq806x_resets[] = {
diff --git a/target/linux/ipq806x/patches-4.0/140-clk-qcom-Add-support-for-Krait-clocks.patch b/target/linux/ipq806x/patches-4.0/140-clk-qcom-Add-support-for-Krait-clocks.patch
new file mode 100644
index 0000000..cef33c8
--- /dev/null
+++ b/target/linux/ipq806x/patches-4.0/140-clk-qcom-Add-support-for-Krait-clocks.patch
@@ -0,0 +1,271 @@
+Content-Type: text/plain; charset="utf-8"
+MIME-Version: 1.0
+Content-Transfer-Encoding: 7bit
+Subject: [v3,09/13] clk: qcom: Add support for Krait clocks
+From: Stephen Boyd <sboyd at codeaurora.org>
+X-Patchwork-Id: 6063251
+Message-Id: <1426920332-9340-10-git-send-email-sboyd at codeaurora.org>
+To: Mike Turquette <mturquette at linaro.org>, Stephen Boyd <sboyd at codeaurora.org>
+Cc: linux-kernel at vger.kernel.org, linux-arm-msm at vger.kernel.org,
+ linux-pm at vger.kernel.org, linux-arm-kernel at lists.infradead.org,
+ Viresh Kumar <viresh.kumar at linaro.org>
+Date: Fri, 20 Mar 2015 23:45:28 -0700
+
+The Krait clocks are made up of a series of muxes and a divider
+that choose between a fixed rate clock and dedicated HFPLLs for
+each CPU. Instead of using mmio accesses to remux parents, the
+Krait implementation exposes the remux control via cp15
+registers. Support these clocks.
+
+Signed-off-by: Stephen Boyd <sboyd at codeaurora.org>
+
+---
+drivers/clk/qcom/Kconfig | 4 ++
+ drivers/clk/qcom/Makefile | 1 +
+ drivers/clk/qcom/clk-krait.c | 166 +++++++++++++++++++++++++++++++++++++++++++
+ drivers/clk/qcom/clk-krait.h | 49 +++++++++++++
+ 4 files changed, 220 insertions(+)
+ create mode 100644 drivers/clk/qcom/clk-krait.c
+ create mode 100644 drivers/clk/qcom/clk-krait.h
+
+--- a/drivers/clk/qcom/Kconfig
++++ b/drivers/clk/qcom/Kconfig
+@@ -96,3 +96,7 @@ config QCOM_HFPLL
+ Support for the high-frequency PLLs present on Qualcomm devices.
+ Say Y if you want to support CPU frequency scaling on devices
+ such as MSM8974, APQ8084, etc.
++
++config KRAIT_CLOCKS
++ bool
++ select KRAIT_L2_ACCESSORS
+--- a/drivers/clk/qcom/Makefile
++++ b/drivers/clk/qcom/Makefile
+@@ -8,6 +8,7 @@ clk-qcom-y += clk-rcg2.o
+ clk-qcom-y += clk-branch.o
+ clk-qcom-y += clk-regmap-divider.o
+ clk-qcom-y += clk-regmap-mux.o
++clk-qcom-$(CONFIG_KRAIT_CLOCKS) += clk-krait.o
+ clk-qcom-y += clk-hfpll.o
+ clk-qcom-y += reset.o
+
+--- /dev/null
++++ b/drivers/clk/qcom/clk-krait.c
+@@ -0,0 +1,166 @@
++/*
++ * Copyright (c) 2013-2014, The Linux Foundation. All rights reserved.
++ *
++ * This program is free software; you can redistribute it and/or modify
++ * it under the terms of the GNU General Public License version 2 and
++ * only version 2 as published by the Free Software Foundation.
++ *
++ * This program is distributed in the hope that it will be useful,
++ * but WITHOUT ANY WARRANTY; without even the implied warranty of
++ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
++ * GNU General Public License for more details.
++ */
++
++#include <linux/kernel.h>
++#include <linux/module.h>
++#include <linux/init.h>
++#include <linux/io.h>
++#include <linux/delay.h>
++#include <linux/err.h>
++#include <linux/clk-provider.h>
++#include <linux/spinlock.h>
++
++#include <asm/krait-l2-accessors.h>
++
++#include "clk-krait.h"
++
++/* Secondary and primary muxes share the same cp15 register */
++static DEFINE_SPINLOCK(krait_clock_reg_lock);
++
++#define LPL_SHIFT 8
++static void __krait_mux_set_sel(struct krait_mux_clk *mux, int sel)
++{
++ unsigned long flags;
++ u32 regval;
++
++ spin_lock_irqsave(&krait_clock_reg_lock, flags);
++ regval = krait_get_l2_indirect_reg(mux->offset);
++ regval &= ~(mux->mask << mux->shift);
++ regval |= (sel & mux->mask) << mux->shift;
++ if (mux->lpl) {
++ regval &= ~(mux->mask << (mux->shift + LPL_SHIFT));
++ regval |= (sel & mux->mask) << (mux->shift + LPL_SHIFT);
++ }
++ krait_set_l2_indirect_reg(mux->offset, regval);
++ spin_unlock_irqrestore(&krait_clock_reg_lock, flags);
++
++ /* Wait for switch to complete. */
++ mb();
++ udelay(1);
++}
++
++static int krait_mux_set_parent(struct clk_hw *hw, u8 index)
++{
++ struct krait_mux_clk *mux = to_krait_mux_clk(hw);
++ u32 sel;
++
++ sel = clk_mux_reindex(index, mux->parent_map, 0);
++ mux->en_mask = sel;
++ /* Don't touch mux if CPU is off as it won't work */
++ if (__clk_is_enabled(hw->clk))
++ __krait_mux_set_sel(mux, sel);
++ return 0;
++}
++
++static u8 krait_mux_get_parent(struct clk_hw *hw)
++{
++ struct krait_mux_clk *mux = to_krait_mux_clk(hw);
++ u32 sel;
++
++ sel = krait_get_l2_indirect_reg(mux->offset);
++ sel >>= mux->shift;
++ sel &= mux->mask;
++ mux->en_mask = sel;
++
++ return clk_mux_get_parent(hw, sel, mux->parent_map, 0);
++}
++
++static struct clk_hw *krait_mux_get_safe_parent(struct clk_hw *hw)
++{
++ int i;
++ struct krait_mux_clk *mux = to_krait_mux_clk(hw);
++ int num_parents = __clk_get_num_parents(hw->clk);
++
++ i = mux->safe_sel;
++ for (i = 0; i < num_parents; i++)
++ if (mux->safe_sel == mux->parent_map[i])
++ break;
++
++ return __clk_get_hw(clk_get_parent_by_index(hw->clk, i));
++}
++
++static int krait_mux_enable(struct clk_hw *hw)
++{
++ struct krait_mux_clk *mux = to_krait_mux_clk(hw);
++
++ __krait_mux_set_sel(mux, mux->en_mask);
++
++ return 0;
++}
++
++static void krait_mux_disable(struct clk_hw *hw)
++{
++ struct krait_mux_clk *mux = to_krait_mux_clk(hw);
++
++ __krait_mux_set_sel(mux, mux->safe_sel);
++}
++
++const struct clk_ops krait_mux_clk_ops = {
++ .enable = krait_mux_enable,
++ .disable = krait_mux_disable,
++ .set_parent = krait_mux_set_parent,
++ .get_parent = krait_mux_get_parent,
++ .determine_rate = __clk_mux_determine_rate_closest,
++ .get_safe_parent = krait_mux_get_safe_parent,
++};
++EXPORT_SYMBOL_GPL(krait_mux_clk_ops);
++
++/* The divider can divide by 2, 4, 6 and 8. But we only really need div-2. */
++static long krait_div2_round_rate(struct clk_hw *hw, unsigned long rate,
++ unsigned long *parent_rate)
++{
++ *parent_rate = __clk_round_rate(__clk_get_parent(hw->clk), rate * 2);
++ return DIV_ROUND_UP(*parent_rate, 2);
++}
++
++static int krait_div2_set_rate(struct clk_hw *hw, unsigned long rate,
++ unsigned long parent_rate)
++{
++ struct krait_div2_clk *d = to_krait_div2_clk(hw);
++ unsigned long flags;
++ u32 val;
++ u32 mask = BIT(d->width) - 1;
++
++ if (d->lpl)
++ mask = mask << (d->shift + LPL_SHIFT) | mask << d->shift;
++
++ spin_lock_irqsave(&krait_clock_reg_lock, flags);
++ val = krait_get_l2_indirect_reg(d->offset);
++ val &= ~mask;
++ krait_set_l2_indirect_reg(d->offset, val);
++ spin_unlock_irqrestore(&krait_clock_reg_lock, flags);
++
++ return 0;
++}
++
++static unsigned long
++krait_div2_recalc_rate(struct clk_hw *hw, unsigned long parent_rate)
++{
++ struct krait_div2_clk *d = to_krait_div2_clk(hw);
++ u32 mask = BIT(d->width) - 1;
++ u32 div;
++
++ div = krait_get_l2_indirect_reg(d->offset);
++ div >>= d->shift;
++ div &= mask;
++ div = (div + 1) * 2;
++
++ return DIV_ROUND_UP(parent_rate, div);
++}
++
++const struct clk_ops krait_div2_clk_ops = {
++ .round_rate = krait_div2_round_rate,
++ .set_rate = krait_div2_set_rate,
++ .recalc_rate = krait_div2_recalc_rate,
++};
++EXPORT_SYMBOL_GPL(krait_div2_clk_ops);
+--- /dev/null
++++ b/drivers/clk/qcom/clk-krait.h
+@@ -0,0 +1,49 @@
++/*
++ * Copyright (c) 2013, The Linux Foundation. All rights reserved.
++ *
++ * This program is free software; you can redistribute it and/or modify
++ * it under the terms of the GNU General Public License version 2 and
++ * only version 2 as published by the Free Software Foundation.
++ *
++ * This program is distributed in the hope that it will be useful,
++ * but WITHOUT ANY WARRANTY; without even the implied warranty of
++ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
++ * GNU General Public License for more details.
++ */
++
++#ifndef __QCOM_CLK_KRAIT_H
++#define __QCOM_CLK_KRAIT_H
++
++#include <linux/clk-provider.h>
++
++struct krait_mux_clk {
++ unsigned int *parent_map;
++ bool has_safe_parent;
++ u8 safe_sel;
++ u32 offset;
++ u32 mask;
++ u32 shift;
++ u32 en_mask;
++ bool lpl;
++
++ struct clk_hw hw;
++};
++
++#define to_krait_mux_clk(_hw) container_of(_hw, struct krait_mux_clk, hw)
++
++extern const struct clk_ops krait_mux_clk_ops;
++
++struct krait_div2_clk {
++ u32 offset;
++ u8 width;
++ u32 shift;
++ bool lpl;
++
++ struct clk_hw hw;
++};
++
++#define to_krait_div2_clk(_hw) container_of(_hw, struct krait_div2_clk, hw)
++
++extern const struct clk_ops krait_div2_clk_ops;
++
++#endif
diff --git a/target/linux/ipq806x/patches-4.0/141-clk-qcom-Add-KPSS-ACC-GCC-driver.patch b/target/linux/ipq806x/patches-4.0/141-clk-qcom-Add-KPSS-ACC-GCC-driver.patch
new file mode 100644
index 0000000..12f24b7
--- /dev/null
+++ b/target/linux/ipq806x/patches-4.0/141-clk-qcom-Add-KPSS-ACC-GCC-driver.patch
@@ -0,0 +1,205 @@
+Content-Type: text/plain; charset="utf-8"
+MIME-Version: 1.0
+Content-Transfer-Encoding: 7bit
+Subject: [v3,10/13] clk: qcom: Add KPSS ACC/GCC driver
+From: Stephen Boyd <sboyd at codeaurora.org>
+X-Patchwork-Id: 6063201
+Message-Id: <1426920332-9340-11-git-send-email-sboyd at codeaurora.org>
+To: Mike Turquette <mturquette at linaro.org>, Stephen Boyd <sboyd at codeaurora.org>
+Cc: linux-kernel at vger.kernel.org, linux-arm-msm at vger.kernel.org,
+ linux-pm at vger.kernel.org, linux-arm-kernel at lists.infradead.org,
+ Viresh Kumar <viresh.kumar at linaro.org>, <devicetree at vger.kernel.org>
+Date: Fri, 20 Mar 2015 23:45:29 -0700
+
+The ACC and GCC regions present in KPSSv1 contain registers to
+control clocks and power to each Krait CPU and L2. For CPUfreq
+purposes probe these devices and expose a mux clock that chooses
+between PXO and PLL8.
+
+Cc: <devicetree at vger.kernel.org>
+Signed-off-by: Stephen Boyd <sboyd at codeaurora.org>
+
+---
+.../devicetree/bindings/arm/msm/qcom,kpss-acc.txt | 7 ++
+ .../devicetree/bindings/arm/msm/qcom,kpss-gcc.txt | 28 +++++++
+ drivers/clk/qcom/Kconfig | 8 ++
+ drivers/clk/qcom/Makefile | 1 +
+ drivers/clk/qcom/kpss-xcc.c | 95 ++++++++++++++++++++++
+ 5 files changed, 139 insertions(+)
+ create mode 100644 Documentation/devicetree/bindings/arm/msm/qcom,kpss-gcc.txt
+ create mode 100644 drivers/clk/qcom/kpss-xcc.c
+
+--- a/Documentation/devicetree/bindings/arm/msm/qcom,kpss-acc.txt
++++ b/Documentation/devicetree/bindings/arm/msm/qcom,kpss-acc.txt
+@@ -21,10 +21,17 @@ PROPERTIES
+ the register region. An optional second element specifies
+ the base address and size of the alias register region.
+
++- clock-output-names:
++ Usage: optional
++ Value type: <string>
++ Definition: Name of the output clock. Typically acpuX_aux where X is a
++ CPU number starting at 0.
++
+ Example:
+
+ clock-controller at 2088000 {
+ compatible = "qcom,kpss-acc-v2";
+ reg = <0x02088000 0x1000>,
+ <0x02008000 0x1000>;
++ clock-output-names = "acpu0_aux";
+ };
+--- /dev/null
++++ b/Documentation/devicetree/bindings/arm/msm/qcom,kpss-gcc.txt
+@@ -0,0 +1,28 @@
++Krait Processor Sub-system (KPSS) Global Clock Controller (GCC)
++
++PROPERTIES
++
++- compatible:
++ Usage: required
++ Value type: <string>
++ Definition: should be one of:
++ "qcom,kpss-gcc"
++
++- reg:
++ Usage: required
++ Value type: <prop-encoded-array>
++ Definition: base address and size of the register region
++
++- clock-output-names:
++ Usage: required
++ Value type: <string>
++ Definition: Name of the output clock. Typically acpu_l2_aux indicating
++ an L2 cache auxiliary clock.
++
++Example:
++
++ l2cc: clock-controller at 2011000 {
++ compatible = "qcom,kpss-gcc";
++ reg = <0x2011000 0x1000>;
++ clock-output-names = "acpu_l2_aux";
++ };
+--- a/drivers/clk/qcom/Kconfig
++++ b/drivers/clk/qcom/Kconfig
+@@ -97,6 +97,14 @@ config QCOM_HFPLL
+ Say Y if you want to support CPU frequency scaling on devices
+ such as MSM8974, APQ8084, etc.
+
++config KPSS_XCC
++ tristate "KPSS Clock Controller"
++ depends on COMMON_CLK_QCOM
++ help
++ Support for the Krait ACC and GCC clock controllers. Say Y
++ if you want to support CPU frequency scaling on devices such
++ as MSM8960, APQ8064, etc.
++
+ config KRAIT_CLOCKS
+ bool
+ select KRAIT_L2_ACCESSORS
+--- a/drivers/clk/qcom/Makefile
++++ b/drivers/clk/qcom/Makefile
+@@ -22,4 +22,5 @@ obj-$(CONFIG_MSM_LCC_8960) += lcc-msm896
+ obj-$(CONFIG_MSM_GCC_8974) += gcc-msm8974.o
+ obj-$(CONFIG_MSM_MMCC_8960) += mmcc-msm8960.o
+ obj-$(CONFIG_MSM_MMCC_8974) += mmcc-msm8974.o
++obj-$(CONFIG_KPSS_XCC) += kpss-xcc.o
+ obj-$(CONFIG_QCOM_HFPLL) += hfpll.o
+--- /dev/null
++++ b/drivers/clk/qcom/kpss-xcc.c
+@@ -0,0 +1,95 @@
++/* Copyright (c) 2014-2015, The Linux Foundation. All rights reserved.
++ *
++ * This program is free software; you can redistribute it and/or modify
++ * it under the terms of the GNU General Public License version 2 and
++ * only version 2 as published by the Free Software Foundation.
++ *
++ * This program is distributed in the hope that it will be useful,
++ * but WITHOUT ANY WARRANTY; without even the implied warranty of
++ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
++ * GNU General Public License for more details.
++ */
++
++#include <linux/kernel.h>
++#include <linux/init.h>
++#include <linux/module.h>
++#include <linux/platform_device.h>
++#include <linux/err.h>
++#include <linux/io.h>
++#include <linux/of.h>
++#include <linux/of_device.h>
++#include <linux/clk.h>
++#include <linux/clk-provider.h>
++
++static const char *aux_parents[] = {
++ "pll8_vote",
++ "pxo",
++};
++
++static unsigned int aux_parent_map[] = {
++ 3,
++ 0,
++};
++
++static const struct of_device_id kpss_xcc_match_table[] = {
++ { .compatible = "qcom,kpss-acc-v1", .data = (void *)1UL },
++ { .compatible = "qcom,kpss-gcc" },
++ {}
++};
++MODULE_DEVICE_TABLE(of, kpss_xcc_match_table);
++
++static int kpss_xcc_driver_probe(struct platform_device *pdev)
++{
++ const struct of_device_id *id;
++ struct clk *clk;
++ struct resource *res;
++ void __iomem *base;
++ const char *name;
++
++ id = of_match_device(kpss_xcc_match_table, &pdev->dev);
++ if (!id)
++ return -ENODEV;
++
++ res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
++ base = devm_ioremap_resource(&pdev->dev, res);
++ if (IS_ERR(base))
++ return PTR_ERR(base);
++
++ if (id->data) {
++ if (of_property_read_string_index(pdev->dev.of_node,
++ "clock-output-names", 0, &name))
++ return -ENODEV;
++ base += 0x14;
++ } else {
++ name = "acpu_l2_aux";
++ base += 0x28;
++ }
++
++ clk = clk_register_mux_table(&pdev->dev, name, aux_parents,
++ ARRAY_SIZE(aux_parents), 0, base, 0, 0x3,
++ 0, aux_parent_map, NULL);
++
++ platform_set_drvdata(pdev, clk);
++
++ return PTR_ERR_OR_ZERO(clk);
++}
++
++static int kpss_xcc_driver_remove(struct platform_device *pdev)
++{
++ clk_unregister_mux(platform_get_drvdata(pdev));
++ return 0;
++}
++
++static struct platform_driver kpss_xcc_driver = {
++ .probe = kpss_xcc_driver_probe,
++ .remove = kpss_xcc_driver_remove,
++ .driver = {
++ .name = "kpss-xcc",
++ .of_match_table = kpss_xcc_match_table,
++ },
++};
++module_platform_driver(kpss_xcc_driver);
++
++MODULE_DESCRIPTION("Krait Processor Sub System (KPSS) Clock Driver");
++MODULE_LICENSE("GPL v2");
++MODULE_ALIAS("platform:kpss-xcc");
diff --git a/target/linux/ipq806x/patches-4.0/142-clk-qcom-Add-Krait-clock-controller-driver.patch b/target/linux/ipq806x/patches-4.0/142-clk-qcom-Add-Krait-clock-controller-driver.patch
new file mode 100644
index 0000000..159facd
--- /dev/null
+++ b/target/linux/ipq806x/patches-4.0/142-clk-qcom-Add-Krait-clock-controller-driver.patch
@@ -0,0 +1,435 @@
+Content-Type: text/plain; charset="utf-8"
+MIME-Version: 1.0
+Content-Transfer-Encoding: 7bit
+Subject: [v3,11/13] clk: qcom: Add Krait clock controller driver
+From: Stephen Boyd <sboyd at codeaurora.org>
+X-Patchwork-Id: 6063121
+Message-Id: <1426920332-9340-12-git-send-email-sboyd at codeaurora.org>
+To: Mike Turquette <mturquette at linaro.org>, Stephen Boyd <sboyd at codeaurora.org>
+Cc: linux-kernel at vger.kernel.org, linux-arm-msm at vger.kernel.org,
+ linux-pm at vger.kernel.org, linux-arm-kernel at lists.infradead.org,
+ Viresh Kumar <viresh.kumar at linaro.org>, <devicetree at vger.kernel.org>
+Date: Fri, 20 Mar 2015 23:45:30 -0700
+
+The Krait CPU clocks are made up of a primary mux and secondary
+mux for each CPU and the L2, controlled via cp15 accessors. For
+Kraits within KPSSv1 each secondary mux accepts a different aux
+source, but on KPSSv2 each secondary mux accepts the same aux
+source.
+
+Cc: <devicetree at vger.kernel.org>
+Signed-off-by: Stephen Boyd <sboyd at codeaurora.org>
+
+---
+.../devicetree/bindings/clock/qcom,krait-cc.txt | 22 ++
+ drivers/clk/qcom/Kconfig | 8 +
+ drivers/clk/qcom/Makefile | 1 +
+ drivers/clk/qcom/krait-cc.c | 352 +++++++++++++++++++++
+ 4 files changed, 383 insertions(+)
+ create mode 100644 Documentation/devicetree/bindings/clock/qcom,krait-cc.txt
+ create mode 100644 drivers/clk/qcom/krait-cc.c
+
+--- /dev/null
++++ b/Documentation/devicetree/bindings/clock/qcom,krait-cc.txt
+@@ -0,0 +1,22 @@
++Krait Clock Controller
++
++PROPERTIES
++
++- compatible:
++ Usage: required
++ Value type: <string>
++ Definition: must be one of:
++ "qcom,krait-cc-v1"
++ "qcom,krait-cc-v2"
++
++- #clock-cells:
++ Usage: required
++ Value type: <u32>
++ Definition: must be 1
++
++Example:
++
++ kraitcc: clock-controller {
++ compatible = "qcom,krait-cc-v1";
++ #clock-cells = <1>;
++ };
+--- a/drivers/clk/qcom/Kconfig
++++ b/drivers/clk/qcom/Kconfig
+@@ -105,6 +105,14 @@ config KPSS_XCC
+ if you want to support CPU frequency scaling on devices such
+ as MSM8960, APQ8064, etc.
+
++config KRAITCC
++ tristate "Krait Clock Controller"
++ depends on COMMON_CLK_QCOM && ARM
++ select KRAIT_CLOCKS
++ help
++ Support for the Krait CPU clocks on Qualcomm devices.
++ Say Y if you want to support CPU frequency scaling.
++
+ config KRAIT_CLOCKS
+ bool
+ select KRAIT_L2_ACCESSORS
+--- a/drivers/clk/qcom/Makefile
++++ b/drivers/clk/qcom/Makefile
+@@ -24,3 +24,4 @@ obj-$(CONFIG_MSM_MMCC_8960) += mmcc-msm8
+ obj-$(CONFIG_MSM_MMCC_8974) += mmcc-msm8974.o
+ obj-$(CONFIG_KPSS_XCC) += kpss-xcc.o
+ obj-$(CONFIG_QCOM_HFPLL) += hfpll.o
++obj-$(CONFIG_KRAITCC) += krait-cc.o
+--- /dev/null
++++ b/drivers/clk/qcom/krait-cc.c
+@@ -0,0 +1,352 @@
++/* Copyright (c) 2013-2015, The Linux Foundation. All rights reserved.
++ *
++ * This program is free software; you can redistribute it and/or modify
++ * it under the terms of the GNU General Public License version 2 and
++ * only version 2 as published by the Free Software Foundation.
++ *
++ * This program is distributed in the hope that it will be useful,
++ * but WITHOUT ANY WARRANTY; without even the implied warranty of
++ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
++ * GNU General Public License for more details.
++ */
++
++#include <linux/kernel.h>
++#include <linux/init.h>
++#include <linux/module.h>
++#include <linux/platform_device.h>
++#include <linux/err.h>
++#include <linux/io.h>
++#include <linux/of.h>
++#include <linux/of_device.h>
++#include <linux/clk.h>
++#include <linux/clk-provider.h>
++#include <linux/slab.h>
++
++#include "clk-krait.h"
++
++static unsigned int sec_mux_map[] = {
++ 2,
++ 0,
++};
++
++static unsigned int pri_mux_map[] = {
++ 1,
++ 2,
++ 0,
++};
++
++static int
++krait_add_div(struct device *dev, int id, const char *s, unsigned offset)
++{
++ struct krait_div2_clk *div;
++ struct clk_init_data init = {
++ .num_parents = 1,
++ .ops = &krait_div2_clk_ops,
++ .flags = CLK_SET_RATE_PARENT,
++ };
++ const char *p_names[1];
++ struct clk *clk;
++
++ div = devm_kzalloc(dev, sizeof(*div), GFP_KERNEL);
++ if (!div)
++ return -ENOMEM;
++
++ div->width = 2;
++ div->shift = 6;
++ div->lpl = id >= 0;
++ div->offset = offset;
++ div->hw.init = &init;
++
++ init.name = kasprintf(GFP_KERNEL, "hfpll%s_div", s);
++ if (!init.name)
++ return -ENOMEM;
++
++ init.parent_names = p_names;
++ p_names[0] = kasprintf(GFP_KERNEL, "hfpll%s", s);
++ if (!p_names[0]) {
++ kfree(init.name);
++ return -ENOMEM;
++ }
++
++ clk = devm_clk_register(dev, &div->hw);
++ kfree(p_names[0]);
++ kfree(init.name);
++
++ return PTR_ERR_OR_ZERO(clk);
++}
++
++static int
++krait_add_sec_mux(struct device *dev, int id, const char *s, unsigned offset,
++ bool unique_aux)
++{
++ struct krait_mux_clk *mux;
++ static const char *sec_mux_list[] = {
++ "acpu_aux",
++ "qsb",
++ };
++ struct clk_init_data init = {
++ .parent_names = sec_mux_list,
++ .num_parents = ARRAY_SIZE(sec_mux_list),
++ .ops = &krait_mux_clk_ops,
++ .flags = CLK_SET_RATE_PARENT,
++ };
++ struct clk *clk;
++
++ mux = devm_kzalloc(dev, sizeof(*mux), GFP_KERNEL);
++ if (!mux)
++ return -ENOMEM;
++
++ mux->offset = offset;
++ mux->lpl = id >= 0;
++ mux->has_safe_parent = true;
++ mux->safe_sel = 2;
++ mux->mask = 0x3;
++ mux->shift = 2;
++ mux->parent_map = sec_mux_map;
++ mux->hw.init = &init;
++
++ init.name = kasprintf(GFP_KERNEL, "krait%s_sec_mux", s);
++ if (!init.name)
++ return -ENOMEM;
++
++ if (unique_aux) {
++ sec_mux_list[0] = kasprintf(GFP_KERNEL, "acpu%s_aux", s);
++ if (!sec_mux_list[0]) {
++ clk = ERR_PTR(-ENOMEM);
++ goto err_aux;
++ }
++ }
++
++ clk = devm_clk_register(dev, &mux->hw);
++
++ if (unique_aux)
++ kfree(sec_mux_list[0]);
++err_aux:
++ kfree(init.name);
++ return PTR_ERR_OR_ZERO(clk);
++}
++
++static struct clk *
++krait_add_pri_mux(struct device *dev, int id, const char *s, unsigned offset)
++{
++ struct krait_mux_clk *mux;
++ const char *p_names[3];
++ struct clk_init_data init = {
++ .parent_names = p_names,
++ .num_parents = ARRAY_SIZE(p_names),
++ .ops = &krait_mux_clk_ops,
++ .flags = CLK_SET_RATE_PARENT,
++ };
++ struct clk *clk;
++
++ mux = devm_kzalloc(dev, sizeof(*mux), GFP_KERNEL);
++ if (!mux)
++ return ERR_PTR(-ENOMEM);
++
++ mux->has_safe_parent = true;
++ mux->safe_sel = 0;
++ mux->mask = 0x3;
++ mux->shift = 0;
++ mux->offset = offset;
++ mux->lpl = id >= 0;
++ mux->parent_map = pri_mux_map;
++ mux->hw.init = &init;
++
++ init.name = kasprintf(GFP_KERNEL, "krait%s_pri_mux", s);
++ if (!init.name)
++ return ERR_PTR(-ENOMEM);
++
++ p_names[0] = kasprintf(GFP_KERNEL, "hfpll%s", s);
++ if (!p_names[0]) {
++ clk = ERR_PTR(-ENOMEM);
++ goto err_p0;
++ }
++
++ p_names[1] = kasprintf(GFP_KERNEL, "hfpll%s_div", s);
++ if (!p_names[1]) {
++ clk = ERR_PTR(-ENOMEM);
++ goto err_p1;
++ }
++
++ p_names[2] = kasprintf(GFP_KERNEL, "krait%s_sec_mux", s);
++ if (!p_names[2]) {
++ clk = ERR_PTR(-ENOMEM);
++ goto err_p2;
++ }
++
++ clk = devm_clk_register(dev, &mux->hw);
++
++ kfree(p_names[2]);
++err_p2:
++ kfree(p_names[1]);
++err_p1:
++ kfree(p_names[0]);
++err_p0:
++ kfree(init.name);
++ return clk;
++}
++
++/* id < 0 for L2, otherwise id == physical CPU number */
++static struct clk *krait_add_clks(struct device *dev, int id, bool unique_aux)
++{
++ int ret;
++ unsigned offset;
++ void *p = NULL;
++ const char *s;
++ struct clk *clk;
++
++ if (id >= 0) {
++ offset = 0x4501 + (0x1000 * id);
++ s = p = kasprintf(GFP_KERNEL, "%d", id);
++ if (!s)
++ return ERR_PTR(-ENOMEM);
++ } else {
++ offset = 0x500;
++ s = "_l2";
++ }
++
++ ret = krait_add_div(dev, id, s, offset);
++ if (ret) {
++ clk = ERR_PTR(ret);
++ goto err;
++ }
++
++ ret = krait_add_sec_mux(dev, id, s, offset, unique_aux);
++ if (ret) {
++ clk = ERR_PTR(ret);
++ goto err;
++ }
++
++ clk = krait_add_pri_mux(dev, id, s, offset);
++err:
++ kfree(p);
++ return clk;
++}
++
++static struct clk *krait_of_get(struct of_phandle_args *clkspec, void *data)
++{
++ unsigned int idx = clkspec->args[0];
++ struct clk **clks = data;
++
++ if (idx >= 5) {
++ pr_err("%s: invalid clock index %d\n", __func__, idx);
++ return ERR_PTR(-EINVAL);
++ }
++
++ return clks[idx] ? : ERR_PTR(-ENODEV);
++}
++
++static const struct of_device_id krait_cc_match_table[] = {
++ { .compatible = "qcom,krait-cc-v1", (void *)1UL },
++ { .compatible = "qcom,krait-cc-v2" },
++ {}
++};
++MODULE_DEVICE_TABLE(of, krait_cc_match_table);
++
++static int krait_cc_probe(struct platform_device *pdev)
++{
++ struct device *dev = &pdev->dev;
++ const struct of_device_id *id;
++ unsigned long cur_rate, aux_rate;
++ int cpu;
++ struct clk *clk;
++ struct clk **clks;
++ struct clk *l2_pri_mux_clk;
++
++ id = of_match_device(krait_cc_match_table, dev);
++ if (!id)
++ return -ENODEV;
++
++ /* Rate is 1 because 0 causes problems for __clk_mux_determine_rate */
++ clk = clk_register_fixed_rate(dev, "qsb", NULL, CLK_IS_ROOT, 1);
++ if (IS_ERR(clk))
++ return PTR_ERR(clk);
++
++ if (!id->data) {
++ clk = clk_register_fixed_factor(dev, "acpu_aux",
++ "gpll0_vote", 0, 1, 2);
++ if (IS_ERR(clk))
++ return PTR_ERR(clk);
++ }
++
++ /* Krait configurations have at most 4 CPUs and one L2 */
++ clks = devm_kcalloc(dev, 5, sizeof(*clks), GFP_KERNEL);
++ if (!clks)
++ return -ENOMEM;
++
++ for_each_possible_cpu(cpu) {
++ clk = krait_add_clks(dev, cpu, id->data);
++ if (IS_ERR(clk))
++ return PTR_ERR(clk);
++ clks[cpu] = clk;
++ }
++
++ l2_pri_mux_clk = krait_add_clks(dev, -1, id->data);
++ if (IS_ERR(l2_pri_mux_clk))
++ return PTR_ERR(l2_pri_mux_clk);
++ clks[4] = l2_pri_mux_clk;
++
++ /*
++ * We don't want the CPU or L2 clocks to be turned off at late init
++ * if CPUFREQ or HOTPLUG configs are disabled. So, bump up the
++ * refcount of these clocks. Any cpufreq/hotplug manager can assume
++ * that the clocks have already been prepared and enabled by the time
++ * they take over.
++ */
++ for_each_online_cpu(cpu) {
++ clk_prepare_enable(l2_pri_mux_clk);
++ WARN(clk_prepare_enable(clks[cpu]),
++ "Unable to turn on CPU%d clock", cpu);
++ }
++
++ /*
++ * Force reinit of HFPLLs and muxes to overwrite any potential
++ * incorrect configuration of HFPLLs and muxes by the bootloader.
++ * While at it, also make sure the cores are running at known rates
++ * and print the current rate.
++ *
++ * The clocks are set to aux clock rate first to make sure the
++ * secondary mux is not sourcing off of QSB. The rate is then set to
++ * two different rates to force a HFPLL reinit under all
++ * circumstances.
++ */
++ cur_rate = clk_get_rate(l2_pri_mux_clk);
++ aux_rate = 384000000;
++ if (cur_rate == 1) {
++ pr_info("L2 @ QSB rate. Forcing new rate.\n");
++ cur_rate = aux_rate;
++ }
++ clk_set_rate(l2_pri_mux_clk, aux_rate);
++ clk_set_rate(l2_pri_mux_clk, 2);
++ clk_set_rate(l2_pri_mux_clk, cur_rate);
++ pr_info("L2 @ %lu KHz\n", clk_get_rate(l2_pri_mux_clk) / 1000);
++ for_each_possible_cpu(cpu) {
++ clk = clks[cpu];
++ cur_rate = clk_get_rate(clk);
++ if (cur_rate == 1) {
++ pr_info("CPU%d @ QSB rate. Forcing new rate.\n", cpu);
++ cur_rate = aux_rate;
++ }
++ clk_set_rate(clk, aux_rate);
++ clk_set_rate(clk, 2);
++ clk_set_rate(clk, cur_rate);
++ pr_info("CPU%d @ %lu KHz\n", cpu, clk_get_rate(clk) / 1000);
++ }
++
++ of_clk_add_provider(dev->of_node, krait_of_get, clks);
++
++ return 0;
++}
++
++static struct platform_driver krait_cc_driver = {
++ .probe = krait_cc_probe,
++ .driver = {
++ .name = "krait-cc",
++ .of_match_table = krait_cc_match_table,
++ },
++};
++module_platform_driver(krait_cc_driver);
++
++MODULE_DESCRIPTION("Krait CPU Clock Driver");
++MODULE_LICENSE("GPL v2");
++MODULE_ALIAS("platform:krait-cc");
diff --git a/target/linux/ipq806x/patches-4.0/143-cpufreq-Add-module-to-register-cpufreq-on-Krait-CPUs.patch b/target/linux/ipq806x/patches-4.0/143-cpufreq-Add-module-to-register-cpufreq-on-Krait-CPUs.patch
new file mode 100644
index 0000000..57d4afe
--- /dev/null
+++ b/target/linux/ipq806x/patches-4.0/143-cpufreq-Add-module-to-register-cpufreq-on-Krait-CPUs.patch
@@ -0,0 +1,304 @@
+Content-Type: text/plain; charset="utf-8"
+MIME-Version: 1.0
+Content-Transfer-Encoding: 7bit
+Subject: [v3,12/13] cpufreq: Add module to register cpufreq on Krait CPUs
+From: Stephen Boyd <sboyd at codeaurora.org>
+X-Patchwork-Id: 6063191
+Message-Id: <1426920332-9340-13-git-send-email-sboyd at codeaurora.org>
+To: Mike Turquette <mturquette at linaro.org>, Stephen Boyd <sboyd at codeaurora.org>
+Cc: linux-kernel at vger.kernel.org, linux-arm-msm at vger.kernel.org,
+ linux-pm at vger.kernel.org, linux-arm-kernel at lists.infradead.org,
+ Viresh Kumar <viresh.kumar at linaro.org>, <devicetree at vger.kernel.org>
+Date: Fri, 20 Mar 2015 23:45:31 -0700
+
+Register a cpufreq-generic device whenever we detect that a
+"qcom,krait" compatible CPU is present in DT.
+
+Cc: <devicetree at vger.kernel.org>
+Signed-off-by: Stephen Boyd <sboyd at codeaurora.org>
+
+---
+.../devicetree/bindings/arm/msm/qcom,pvs.txt | 38 ++++
+ drivers/cpufreq/Kconfig.arm | 9 +
+ drivers/cpufreq/Makefile | 1 +
+ drivers/cpufreq/qcom-cpufreq.c | 204 +++++++++++++++++++++
+ 4 files changed, 252 insertions(+)
+ create mode 100644 Documentation/devicetree/bindings/arm/msm/qcom,pvs.txt
+ create mode 100644 drivers/cpufreq/qcom-cpufreq.c
+
+--- /dev/null
++++ b/Documentation/devicetree/bindings/arm/msm/qcom,pvs.txt
+@@ -0,0 +1,38 @@
++Qualcomm Process Voltage Scaling Tables
++
++The node name is required to be "qcom,pvs". There shall only be one
++such node present in the root of the tree.
++
++PROPERTIES
++
++- qcom,pvs-format-a or qcom,pvs-format-b:
++ Usage: required
++ Value type: <empty>
++ Definition: Indicates the format of qcom,speedX-pvsY-bin-vZ properties.
++ If qcom,pvs-format-a is used the table is two columns
++ (frequency and voltage in that order). If qcom,pvs-format-b is used the table is three columns (frequency, voltage,
++ and current in that order).
++
++- qcom,speedX-pvsY-bin-vZ:
++ Usage: required
++ Value type: <prop-encoded-array>
++ Definition: The PVS table corresponding to the speed bin X, pvs bin Y,
++ and version Z.
++Example:
++
++ qcom,pvs {
++ qcom,pvs-format-a;
++ qcom,speed0-pvs0-bin-v0 =
++ < 384000000 950000 >,
++ < 486000000 975000 >,
++ < 594000000 1000000 >,
++ < 702000000 1025000 >,
++ < 810000000 1075000 >,
++ < 918000000 1100000 >,
++ < 1026000000 1125000 >,
++ < 1134000000 1175000 >,
++ < 1242000000 1200000 >,
++ < 1350000000 1225000 >,
++ < 1458000000 1237500 >,
++ < 1512000000 1250000 >;
++ };
+--- a/drivers/cpufreq/Kconfig.arm
++++ b/drivers/cpufreq/Kconfig.arm
+@@ -137,6 +137,15 @@ config ARM_OMAP2PLUS_CPUFREQ
+ depends on ARCH_OMAP2PLUS
+ default ARCH_OMAP2PLUS
+
++config ARM_QCOM_CPUFREQ
++ tristate "Qualcomm based"
++ depends on ARCH_QCOM
++ select PM_OPP
++ help
++ This adds the CPUFreq driver for Qualcomm SoC based boards.
++
++ If in doubt, say N.
++
+ config ARM_S3C_CPUFREQ
+ bool
+ help
+--- a/drivers/cpufreq/Makefile
++++ b/drivers/cpufreq/Makefile
+@@ -65,6 +65,7 @@ obj-$(CONFIG_ARM_KIRKWOOD_CPUFREQ) += ki
+ obj-$(CONFIG_ARM_OMAP2PLUS_CPUFREQ) += omap-cpufreq.o
+ obj-$(CONFIG_ARM_PXA2xx_CPUFREQ) += pxa2xx-cpufreq.o
+ obj-$(CONFIG_PXA3xx) += pxa3xx-cpufreq.o
++obj-$(CONFIG_ARM_QCOM_CPUFREQ) += qcom-cpufreq.o
+ obj-$(CONFIG_ARM_S3C24XX_CPUFREQ) += s3c24xx-cpufreq.o
+ obj-$(CONFIG_ARM_S3C24XX_CPUFREQ_DEBUGFS) += s3c24xx-cpufreq-debugfs.o
+ obj-$(CONFIG_ARM_S3C2410_CPUFREQ) += s3c2410-cpufreq.o
+--- /dev/null
++++ b/drivers/cpufreq/qcom-cpufreq.c
+@@ -0,0 +1,204 @@
++/* Copyright (c) 2014, The Linux Foundation. All rights reserved.
++ *
++ * This program is free software; you can redistribute it and/or modify
++ * it under the terms of the GNU General Public License version 2 and
++ * only version 2 as published by the Free Software Foundation.
++ *
++ * This program is distributed in the hope that it will be useful,
++ * but WITHOUT ANY WARRANTY; without even the implied warranty of
++ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
++ * GNU General Public License for more details.
++ */
++
++#include <linux/cpu.h>
++#include <linux/err.h>
++#include <linux/init.h>
++#include <linux/io.h>
++#include <linux/kernel.h>
++#include <linux/module.h>
++#include <linux/of.h>
++#include <linux/platform_device.h>
++#include <linux/pm_opp.h>
++#include <linux/slab.h>
++#include <linux/cpufreq-dt.h>
++
++static void __init get_krait_bin_format_a(int *speed, int *pvs, int *pvs_ver)
++{
++ void __iomem *base;
++ u32 pte_efuse;
++
++ *speed = *pvs = *pvs_ver = 0;
++
++ base = ioremap(0x007000c0, 4);
++ if (!base) {
++ pr_warn("Unable to read efuse data. Defaulting to 0!\n");
++ return;
++ }
++
++ pte_efuse = readl_relaxed(base);
++ iounmap(base);
++
++ *speed = pte_efuse & 0xf;
++ if (*speed == 0xf)
++ *speed = (pte_efuse >> 4) & 0xf;
++
++ if (*speed == 0xf) {
++ *speed = 0;
++ pr_warn("Speed bin: Defaulting to %d\n", *speed);
++ } else {
++ pr_info("Speed bin: %d\n", *speed);
++ }
++
++ *pvs = (pte_efuse >> 10) & 0x7;
++ if (*pvs == 0x7)
++ *pvs = (pte_efuse >> 13) & 0x7;
++
++ if (*pvs == 0x7) {
++ *pvs = 0;
++ pr_warn("PVS bin: Defaulting to %d\n", *pvs);
++ } else {
++ pr_info("PVS bin: %d\n", *pvs);
++ }
++}
++
++static void __init get_krait_bin_format_b(int *speed, int *pvs, int *pvs_ver)
++{
++ u32 pte_efuse, redundant_sel;
++ void __iomem *base;
++
++ *speed = 0;
++ *pvs = 0;
++ *pvs_ver = 0;
++
++ base = ioremap(0xfc4b80b0, 8);
++ if (!base) {
++ pr_warn("Unable to read efuse data. Defaulting to 0!\n");
++ return;
++ }
++
++ pte_efuse = readl_relaxed(base);
++ redundant_sel = (pte_efuse >> 24) & 0x7;
++ *speed = pte_efuse & 0x7;
++ /* 4 bits of PVS are in efuse register bits 31, 8-6. */
++ *pvs = ((pte_efuse >> 28) & 0x8) | ((pte_efuse >> 6) & 0x7);
++ *pvs_ver = (pte_efuse >> 4) & 0x3;
++
++ switch (redundant_sel) {
++ case 1:
++ *speed = (pte_efuse >> 27) & 0xf;
++ break;
++ case 2:
++ *pvs = (pte_efuse >> 27) & 0xf;
++ break;
++ }
++
++ /* Check SPEED_BIN_BLOW_STATUS */
++ if (pte_efuse & BIT(3)) {
++ pr_info("Speed bin: %d\n", *speed);
++ } else {
++ pr_warn("Speed bin not set. Defaulting to 0!\n");
++ *speed = 0;
++ }
++
++ /* Check PVS_BLOW_STATUS */
++ pte_efuse = readl_relaxed(base + 0x4) & BIT(21);
++ if (pte_efuse) {
++ pr_info("PVS bin: %d\n", *pvs);
++ } else {
++ pr_warn("PVS bin not set. Defaulting to 0!\n");
++ *pvs = 0;
++ }
++
++ pr_info("PVS version: %d\n", *pvs_ver);
++ iounmap(base);
++}
++
++static int __init qcom_cpufreq_populate_opps(void)
++{
++ int len, rows, cols, i, k, speed, pvs, pvs_ver;
++ char table_name[] = "qcom,speedXX-pvsXX-bin-vXX";
++ struct device_node *np;
++ struct device *dev;
++ int cpu = 0;
++
++ np = of_find_node_by_name(NULL, "qcom,pvs");
++ if (!np)
++ return -ENODEV;
++
++ if (of_property_read_bool(np, "qcom,pvs-format-a")) {
++ get_krait_bin_format_a(&speed, &pvs, &pvs_ver);
++ cols = 2;
++ } else if (of_property_read_bool(np, "qcom,pvs-format-b")) {
++ get_krait_bin_format_b(&speed, &pvs, &pvs_ver);
++ cols = 3;
++ } else {
++ return -ENODEV;
++ }
++
++ snprintf(table_name, sizeof(table_name),
++ "qcom,speed%d-pvs%d-bin-v%d", speed, pvs, pvs_ver);
++
++ if (!of_find_property(np, table_name, &len))
++ return -EINVAL;
++
++ len /= sizeof(u32);
++ if (len % cols || len == 0)
++ return -EINVAL;
++
++ rows = len / cols;
++
++ for (i = 0, k = 0; i < rows; i++) {
++ u32 freq, volt;
++
++ of_property_read_u32_index(np, table_name, k++, &freq);
++ of_property_read_u32_index(np, table_name, k++, &volt);
++ while (k % cols)
++ k++; /* Skip uA entries if present */
++ for (cpu = 0; cpu < num_possible_cpus(); cpu++) {
++ dev = get_cpu_device(cpu);
++ if (!dev)
++ return -ENODEV;
++ if (dev_pm_opp_add(dev, freq, volt))
++ pr_warn("failed to add OPP %u\n", freq);
++ }
++ }
++
++ return 0;
++}
++
++static int __init qcom_cpufreq_driver_init(void)
++{
++ struct cpufreq_dt_platform_data pdata = { .independent_clocks = true };
++ struct platform_device_info devinfo = {
++ .name = "cpufreq-dt",
++ .data = &pdata,
++ .size_data = sizeof(pdata),
++ };
++ struct device *cpu_dev;
++ struct device_node *np;
++ int ret;
++
++ cpu_dev = get_cpu_device(0);
++ if (!cpu_dev)
++ return -ENODEV;
++
++ np = of_node_get(cpu_dev->of_node);
++ if (!np)
++ return -ENOENT;
++
++ if (!of_device_is_compatible(np, "qcom,krait")) {
++ of_node_put(np);
++ return -ENODEV;
++ }
++ of_node_put(np);
++
++ ret = qcom_cpufreq_populate_opps();
++ if (ret)
++ return ret;
++
++ return PTR_ERR_OR_ZERO(platform_device_register_full(&devinfo));
++}
++module_init(qcom_cpufreq_driver_init);
++
++MODULE_DESCRIPTION("Qualcomm CPUfreq driver");
++MODULE_LICENSE("GPL v2");
diff --git a/target/linux/ipq806x/patches-4.0/144-ARM-dts-qcom-Add-necessary-DT-data-for-Krait-cpufreq.patch b/target/linux/ipq806x/patches-4.0/144-ARM-dts-qcom-Add-necessary-DT-data-for-Krait-cpufreq.patch
new file mode 100644
index 0000000..9f8d8cb
--- /dev/null
+++ b/target/linux/ipq806x/patches-4.0/144-ARM-dts-qcom-Add-necessary-DT-data-for-Krait-cpufreq.patch
@@ -0,0 +1,100 @@
+--- a/arch/arm/boot/dts/qcom-ipq8064.dtsi
++++ b/arch/arm/boot/dts/qcom-ipq8064.dtsi
+@@ -23,6 +23,11 @@
+ next-level-cache = <&L2>;
+ qcom,acc = <&acc0>;
+ qcom,saw = <&saw0>;
++ clocks = <&kraitcc 0>;
++ clock-names = "cpu";
++ clock-latency = <100000>;
++ core-supply = <&smb208_s2a>;
++ voltage-tolerance = <5>;
+ };
+
+ cpu at 1 {
+@@ -33,11 +38,24 @@
+ next-level-cache = <&L2>;
+ qcom,acc = <&acc1>;
+ qcom,saw = <&saw1>;
++ clocks = <&kraitcc 1>;
++ clock-names = "cpu";
++ clock-latency = <100000>;
++ core-supply = <&smb208_s2b>;
+ };
+
+ L2: l2-cache {
+ compatible = "cache";
+ cache-level = <2>;
++ clocks = <&kraitcc 4>;
++ clock-names = "cache";
++ cache-points-kHz = <
++ /* kHz uV CPU kHz */
++ 1200000 1150000 1200000
++ 1000000 1100000 600000
++ 384000 1100000 384000
++ >;
++ vdd_dig-supply = <&smb208_s1a>;
+ };
+ };
+
+@@ -70,6 +88,46 @@
+ };
+ };
+
++ kraitcc: clock-controller {
++ compatible = "qcom,krait-cc-v1";
++ #clock-cells = <1>;
++ };
++
++ qcom,pvs {
++ qcom,pvs-format-a;
++ qcom,speed0-pvs0-bin-v0 =
++ < 1400000000 1250000 >,
++ < 1200000000 1200000 >,
++ < 1000000000 1150000 >,
++ < 800000000 1100000 >,
++ < 600000000 1050000 >,
++ < 384000000 1000000 >;
++
++ qcom,speed0-pvs1-bin-v0 =
++ < 1400000000 1175000 >,
++ < 1200000000 1125000 >,
++ < 1000000000 1075000 >,
++ < 800000000 1025000 >,
++ < 600000000 975000 >,
++ < 384000000 925000 >;
++
++ qcom,speed0-pvs2-bin-v0 =
++ < 1400000000 1125000 >,
++ < 1200000000 1075000 >,
++ < 1000000000 1025000 >,
++ < 800000000 995000 >,
++ < 600000000 925000 >,
++ < 384000000 875000 >;
++
++ qcom,speed0-pvs3-bin-v0 =
++ < 1400000000 1050000 >,
++ < 1200000000 1000000 >,
++ < 1000000000 950000 >,
++ < 800000000 900000 >,
++ < 600000000 850000 >,
++ < 384000000 800000 >;
++ };
++
+ soc: soc {
+ #address-cells = <1>;
+ #size-cells = <1>;
+@@ -170,11 +228,13 @@
+ acc0: clock-controller at 2088000 {
+ compatible = "qcom,kpss-acc-v1";
+ reg = <0x02088000 0x1000>, <0x02008000 0x1000>;
++ clock-output-names = "acpu0_aux";
+ };
+
+ acc1: clock-controller at 2098000 {
+ compatible = "qcom,kpss-acc-v1";
+ reg = <0x02098000 0x1000>, <0x02008000 0x1000>;
++ clock-output-names = "acpu1_aux";
+ };
+
+ l2cc: clock-controller at 2011000 {
diff --git a/target/linux/ipq806x/patches-4.0/145-cpufreq-Add-a-cpufreq-krait-based-on-cpufre.patch b/target/linux/ipq806x/patches-4.0/145-cpufreq-Add-a-cpufreq-krait-based-on-cpufre.patch
new file mode 100644
index 0000000..521adc5
--- /dev/null
+++ b/target/linux/ipq806x/patches-4.0/145-cpufreq-Add-a-cpufreq-krait-based-on-cpufre.patch
@@ -0,0 +1,461 @@
+From dd77db4143290689d3a5e1ec61627233d0711b66 Mon Sep 17 00:00:00 2001
+From: Stephen Boyd <sboyd at codeaurora.org>
+Date: Fri, 30 May 2014 16:36:11 -0700
+Subject: [PATCH] FROMLIST: cpufreq: Add a cpufreq-krait based on cpufreq-cpu0
+
+Krait processors have individual clocks for each CPU that can
+scale independently from one another. cpufreq-cpu0 is fairly
+close to this, but assumes that there is only one clock for all
+CPUs. Add a driver to support the Krait configuration.
+
+TODO: Merge into cpufreq-cpu0? Or make generic?
+
+Signed-off-by: Stephen Boyd <sboyd at codeaurora.org>
+
+---
+ drivers/cpufreq/Kconfig | 13 +++
+ drivers/cpufreq/Makefile | 1 +
+ drivers/cpufreq/cpufreq-krait.c | 190 ++++++++++++++++++++++++++++++++++++++++
+ 3 files changed, 204 insertions(+)
+ create mode 100644 drivers/cpufreq/cpufreq-krait.c
+
+--- a/drivers/cpufreq/Kconfig
++++ b/drivers/cpufreq/Kconfig
+@@ -198,6 +198,19 @@ config CPUFREQ_DT
+
+ If in doubt, say N.
+
++config GENERIC_CPUFREQ_KRAIT
++ tristate "Krait cpufreq driver"
++ depends on HAVE_CLK && OF
++ # if CPU_THERMAL is on and THERMAL=m, CPU0 cannot be =y:
++ depends on !CPU_THERMAL || THERMAL
++ select PM_OPP
++ help
++ This adds a generic cpufreq driver for CPU0 frequency management.
++ It supports both uniprocessor (UP) and symmetric multiprocessor (SMP)
++ systems which share clock and voltage across all CPUs.
++
++ If in doubt, say N.
++
+ if X86
+ source "drivers/cpufreq/Kconfig.x86"
+ endif
+--- a/drivers/cpufreq/Makefile
++++ b/drivers/cpufreq/Makefile
+@@ -14,6 +14,7 @@ obj-$(CONFIG_CPU_FREQ_GOV_CONSERVATIVE)
+ obj-$(CONFIG_CPU_FREQ_GOV_COMMON) += cpufreq_governor.o
+
+ obj-$(CONFIG_CPUFREQ_DT) += cpufreq-dt.o
++obj-$(CONFIG_GENERIC_CPUFREQ_KRAIT) += cpufreq-krait.o
+
+ ##################################################################################
+ # x86 drivers.
+--- /dev/null
++++ b/drivers/cpufreq/cpufreq-krait.c
+@@ -0,0 +1,390 @@
++/*
++ * Copyright (C) 2012 Freescale Semiconductor, Inc.
++ * Copyright (c) 2014, The Linux Foundation. All rights reserved.
++ *
++ * The OPP code in function krait_set_target() is reused from
++ * drivers/cpufreq/omap-cpufreq.c
++ *
++ * This program is free software; you can redistribute it and/or modify
++ * it under the terms of the GNU General Public License version 2 as
++ * published by the Free Software Foundation.
++ */
++
++#include <linux/clk.h>
++#include <linux/cpu.h>
++#include <linux/cpu_cooling.h>
++#include <linux/cpufreq.h>
++#include <linux/cpumask.h>
++#include <linux/err.h>
++#include <linux/module.h>
++#include <linux/of.h>
++#include <linux/pm_opp.h>
++#include <linux/platform_device.h>
++#include <linux/regulator/consumer.h>
++#include <linux/slab.h>
++#include <linux/thermal.h>
++
++static unsigned int transition_latency;
++static unsigned int voltage_tolerance; /* in percentage */
++
++static struct device *cpu_dev;
++static DEFINE_PER_CPU(struct clk *, krait_cpu_clks);
++static DEFINE_PER_CPU(struct regulator *, krait_supply_core);
++static struct cpufreq_frequency_table *freq_table;
++static struct thermal_cooling_device *cdev;
++
++struct cache_points {
++ unsigned long cache_freq;
++ unsigned int cache_volt;
++ unsigned long cpu_freq;
++};
++
++static struct regulator *krait_l2_reg;
++static struct clk *krait_l2_clk;
++static struct cache_points *krait_l2_points;
++static int nr_krait_l2_points;
++
++static int krait_parse_cache_points(struct device *dev,
++ struct device_node *of_node)
++{
++ const struct property *prop;
++ const __be32 *val;
++ int nr, i;
++
++ prop = of_find_property(of_node, "cache-points-kHz", NULL);
++ if (!prop)
++ return -ENODEV;
++ if (!prop->value)
++ return -ENODATA;
++
++ /*
++ * Each OPP is a set of tuples consisting of frequency and
++ * cpu-frequency like <freq-kHz volt-uV freq-kHz>.
++ */
++ nr = prop->length / sizeof(u32);
++ if (nr % 3) {
++ dev_err(dev, "%s: Invalid cache points\n", __func__);
++ return -EINVAL;
++ }
++ nr /= 3;
++
++ krait_l2_points = devm_kcalloc(dev, nr, sizeof(*krait_l2_points),
++ GFP_KERNEL);
++ if (!krait_l2_points)
++ return -ENOMEM;
++ nr_krait_l2_points = nr;
++
++ for (i = 0, val = prop->value; i < nr; i++) {
++ unsigned long cache_freq = be32_to_cpup(val++) * 1000;
++ unsigned int cache_volt = be32_to_cpup(val++);
++ unsigned long cpu_freq = be32_to_cpup(val++) * 1000;
++
++ krait_l2_points[i].cache_freq = cache_freq;
++ krait_l2_points[i].cache_volt = cache_volt;
++ krait_l2_points[i].cpu_freq = cpu_freq;
++ }
++
++ return 0;
++}
++
++static int krait_set_target(struct cpufreq_policy *policy, unsigned int index)
++{
++ struct dev_pm_opp *opp;
++ unsigned long volt = 0, volt_old = 0, tol = 0;
++ unsigned long freq, max_cpu_freq = 0;
++ unsigned int old_freq, new_freq;
++ long freq_Hz, freq_exact;
++ int ret, i;
++ struct clk *cpu_clk;
++ struct regulator *core;
++ unsigned int cpu;
++
++ cpu_clk = per_cpu(krait_cpu_clks, policy->cpu);
++
++ freq_Hz = clk_round_rate(cpu_clk, freq_table[index].frequency * 1000);
++ if (freq_Hz <= 0)
++ freq_Hz = freq_table[index].frequency * 1000;
++
++ freq_exact = freq_Hz;
++ new_freq = freq_Hz / 1000;
++ old_freq = clk_get_rate(cpu_clk) / 1000;
++
++ core = per_cpu(krait_supply_core, policy->cpu);
++
++ rcu_read_lock();
++ opp = dev_pm_opp_find_freq_ceil(cpu_dev, &freq_Hz);
++ if (IS_ERR(opp)) {
++ rcu_read_unlock();
++ pr_err("failed to find OPP for %ld\n", freq_Hz);
++ return PTR_ERR(opp);
++ }
++ volt = dev_pm_opp_get_voltage(opp);
++ rcu_read_unlock();
++ tol = volt * voltage_tolerance / 100;
++ volt_old = regulator_get_voltage(core);
++
++ pr_debug("%u MHz, %ld mV --> %u MHz, %ld mV\n",
++ old_freq / 1000, volt_old ? volt_old / 1000 : -1,
++ new_freq / 1000, volt ? volt / 1000 : -1);
++
++ /* scaling up? scale voltage before frequency */
++ if (new_freq > old_freq) {
++ ret = regulator_set_voltage_tol(core, volt, tol);
++ if (ret) {
++ pr_err("failed to scale voltage up: %d\n", ret);
++ return ret;
++ }
++ }
++
++ ret = clk_set_rate(cpu_clk, freq_exact);
++ if (ret) {
++ pr_err("failed to set clock rate: %d\n", ret);
++ return ret;
++ }
++
++ /* scaling down? scale voltage after frequency */
++ if (new_freq < old_freq) {
++ ret = regulator_set_voltage_tol(core, volt, tol);
++ if (ret) {
++ pr_err("failed to scale voltage down: %d\n", ret);
++ clk_set_rate(cpu_clk, old_freq * 1000);
++ }
++ }
++
++ for_each_possible_cpu(cpu) {
++ freq = clk_get_rate(per_cpu(krait_cpu_clks, cpu));
++ max_cpu_freq = max(max_cpu_freq, freq);
++ }
++
++ for (i = 0; i < nr_krait_l2_points; i++) {
++ if (max_cpu_freq >= krait_l2_points[i].cpu_freq) {
++ if (krait_l2_reg) {
++ ret = regulator_set_voltage_tol(krait_l2_reg,
++ krait_l2_points[i].cache_volt,
++ tol);
++ if (ret) {
++ pr_err("failed to scale l2 voltage: %d\n",
++ ret);
++ }
++ }
++ ret = clk_set_rate(krait_l2_clk,
++ krait_l2_points[i].cache_freq);
++ if (ret)
++ pr_err("failed to scale l2 clk: %d\n", ret);
++ break;
++ }
++
++ }
++
++ return ret;
++}
++
++static int krait_cpufreq_init(struct cpufreq_policy *policy)
++{
++ int ret;
++
++ policy->clk = per_cpu(krait_cpu_clks, policy->cpu);
++
++ ret = cpufreq_table_validate_and_show(policy, freq_table);
++ if (ret) {
++ pr_err("%s: invalid frequency table: %d\n", __func__, ret);
++ return ret;
++ }
++
++ policy->cpuinfo.transition_latency = transition_latency;
++
++ return 0;
++}
++
++static struct cpufreq_driver krait_cpufreq_driver = {
++ .flags = CPUFREQ_STICKY,
++ .verify = cpufreq_generic_frequency_table_verify,
++ .target_index = krait_set_target,
++ .get = cpufreq_generic_get,
++ .init = krait_cpufreq_init,
++ .name = "generic_krait",
++ .attr = cpufreq_generic_attr,
++};
++
++static int krait_cpufreq_probe(struct platform_device *pdev)
++{
++ struct device_node *np, *cache;
++ int ret, i;
++ unsigned int cpu;
++ struct device *dev;
++ struct clk *clk;
++ struct regulator *core;
++ unsigned long freq_Hz, freq, max_cpu_freq;
++ struct dev_pm_opp *opp;
++ unsigned long volt, tol;
++
++ cpu_dev = get_cpu_device(0);
++ if (!cpu_dev) {
++ pr_err("failed to get krait device\n");
++ return -ENODEV;
++ }
++
++ np = of_node_get(cpu_dev->of_node);
++ if (!np) {
++ pr_err("failed to find krait node\n");
++ return -ENOENT;
++ }
++
++ ret = dev_pm_opp_init_cpufreq_table(cpu_dev, &freq_table);
++ if (ret) {
++ pr_err("failed to init cpufreq table: %d\n", ret);
++ goto out_put_node;
++ }
++
++ of_property_read_u32(np, "voltage-tolerance", &voltage_tolerance);
++
++ if (of_property_read_u32(np, "clock-latency", &transition_latency))
++ transition_latency = CPUFREQ_ETERNAL;
++
++ cache = of_find_next_cache_node(np);
++ if (cache) {
++ struct device_node *vdd;
++
++ vdd = of_parse_phandle(cache, "vdd_dig-supply", 0);
++ if (vdd) {
++ krait_l2_reg = regulator_get(NULL, vdd->name);
++ if (IS_ERR(krait_l2_reg)) {
++ pr_warn("failed to get l2 vdd_dig supply\n");
++ krait_l2_reg = NULL;
++ }
++ of_node_put(vdd);
++ }
++
++ krait_l2_clk = of_clk_get(cache, 0);
++ if (!IS_ERR(krait_l2_clk)) {
++ ret = krait_parse_cache_points(&pdev->dev, cache);
++ if (ret)
++ clk_put(krait_l2_clk);
++ }
++ if (IS_ERR(krait_l2_clk) || ret)
++ krait_l2_clk = NULL;
++ }
++
++ for_each_possible_cpu(cpu) {
++ dev = get_cpu_device(cpu);
++ if (!dev) {
++ pr_err("failed to get krait device\n");
++ ret = -ENOENT;
++ goto out_free_table;
++ }
++ per_cpu(krait_cpu_clks, cpu) = clk = devm_clk_get(dev, NULL);
++ if (IS_ERR(clk)) {
++ ret = PTR_ERR(clk);
++ goto out_free_table;
++ }
++ core = devm_regulator_get(dev, "core");
++ if (IS_ERR(core)) {
++ pr_debug("failed to get core regulator\n");
++ ret = PTR_ERR(core);
++ goto out_free_table;
++ }
++ per_cpu(krait_supply_core, cpu) = core;
++
++ freq_Hz = clk_get_rate(clk);
++
++ rcu_read_lock();
++ opp = dev_pm_opp_find_freq_ceil(cpu_dev, &freq_Hz);
++ if (IS_ERR(opp)) {
++ rcu_read_unlock();
++ pr_err("failed to find OPP for %ld\n", freq_Hz);
++ ret = PTR_ERR(opp);
++ goto out_free_table;
++ }
++ volt = dev_pm_opp_get_voltage(opp);
++ rcu_read_unlock();
++
++ tol = volt * voltage_tolerance / 100;
++ ret = regulator_set_voltage_tol(core, volt, tol);
++ if (ret) {
++ pr_err("failed to scale voltage up: %d\n", ret);
++ goto out_free_table;
++ }
++ ret = regulator_enable(core);
++ if (ret) {
++ pr_err("failed to enable regulator: %d\n", ret);
++ goto out_free_table;
++ }
++ max_cpu_freq = max(max_cpu_freq, freq);
++ }
++
++ for (i = 0; i < nr_krait_l2_points; i++) {
++ if (max_cpu_freq >= krait_l2_points[i].cpu_freq) {
++ if (krait_l2_reg) {
++ ret = regulator_set_voltage_tol(krait_l2_reg,
++ krait_l2_points[i].cache_volt,
++ tol);
++ if (ret)
++ pr_err("failed to scale l2 voltage: %d\n",
++ ret);
++ ret = regulator_enable(krait_l2_reg);
++ if (ret)
++ pr_err("failed to enable l2 voltage: %d\n",
++ ret);
++ }
++ break;
++ }
++
++ }
++
++ ret = cpufreq_register_driver(&krait_cpufreq_driver);
++ if (ret) {
++ pr_err("failed register driver: %d\n", ret);
++ goto out_free_table;
++ }
++ of_node_put(np);
++
++ /*
++ * For now, just loading the cooling device;
++ * thermal DT code takes care of matching them.
++ */
++ for_each_possible_cpu(cpu) {
++ dev = get_cpu_device(cpu);
++ np = of_node_get(dev->of_node);
++ if (of_find_property(np, "#cooling-cells", NULL)) {
++ cdev = of_cpufreq_cooling_register(np, cpumask_of(cpu));
++ if (IS_ERR(cdev))
++ pr_err("running cpufreq without cooling device: %ld\n",
++ PTR_ERR(cdev));
++ }
++ of_node_put(np);
++ }
++
++ return 0;
++
++out_free_table:
++ regulator_put(krait_l2_reg);
++ clk_put(krait_l2_clk);
++ dev_pm_opp_free_cpufreq_table(cpu_dev, &freq_table);
++out_put_node:
++ of_node_put(np);
++ return ret;
++}
++
++static int krait_cpufreq_remove(struct platform_device *pdev)
++{
++ cpufreq_cooling_unregister(cdev);
++ cpufreq_unregister_driver(&krait_cpufreq_driver);
++ dev_pm_opp_free_cpufreq_table(cpu_dev, &freq_table);
++ clk_put(krait_l2_clk);
++ regulator_put(krait_l2_reg);
++
++ return 0;
++}
++
++static struct platform_driver krait_cpufreq_platdrv = {
++ .driver = {
++ .name = "cpufreq-krait",
++ .owner = THIS_MODULE,
++ },
++ .probe = krait_cpufreq_probe,
++ .remove = krait_cpufreq_remove,
++};
++module_platform_driver(krait_cpufreq_platdrv);
++
++MODULE_DESCRIPTION("Krait CPUfreq driver");
++MODULE_LICENSE("GPL v2");
+--- a/drivers/cpufreq/qcom-cpufreq.c
++++ b/drivers/cpufreq/qcom-cpufreq.c
+@@ -168,11 +168,8 @@ static int __init qcom_cpufreq_populate_
+
+ static int __init qcom_cpufreq_driver_init(void)
+ {
+- struct cpufreq_dt_platform_data pdata = { .independent_clocks = true };
+ struct platform_device_info devinfo = {
+- .name = "cpufreq-dt",
+- .data = &pdata,
+- .size_data = sizeof(pdata),
++ .name = "cpufreq-krait",
+ };
+ struct device *cpu_dev;
+ struct device_node *np;
diff --git a/target/linux/ipq806x/patches-4.0/700-add-gmac-dts-suport.patch b/target/linux/ipq806x/patches-4.0/700-add-gmac-dts-suport.patch
index 25a9373..7b628a7 100644
--- a/target/linux/ipq806x/patches-4.0/700-add-gmac-dts-suport.patch
+++ b/target/linux/ipq806x/patches-4.0/700-add-gmac-dts-suport.patch
@@ -127,7 +127,7 @@
/ {
model = "Qualcomm IPQ8064";
-@@ -479,5 +480,42 @@
+@@ -539,5 +540,42 @@
status = "disabled";
};
--
2.1.4
_______________________________________________
openwrt-devel mailing list
openwrt-devel at lists.openwrt.org
https://lists.openwrt.org/cgi-bin/mailman/listinfo/openwrt-devel
More information about the openwrt-devel
mailing list