[OpenWrt-Devel] [PATCH] ramips: adding support for OY-0001 Wireless Router
LiWeijian
younfan33 at hotmail.com
Fri Jul 10 10:28:29 EDT 2015
Hi，
Thanks very much for your comments and taking time to check the name. Regarding the 'OY-0001', it's for business reason to use 'OY-0001' but not 'OYE-0001'. The 'old' name in the website also will be updated afterward.
Regards,
Weijian
> Subject: Re: [OpenWrt-Devel] [PATCH] ramips: adding support for OY-0001 Wireless Router
> From: karlp at tweak.net.au
> To: younfan33 at hotmail.com
> CC: openwrt-devel at lists.openwrt.org
> Date: Fri, 10 Jul 2015 11:27:55 +0000
>
> -----BEGIN PGP SIGNED MESSAGE-----
> Hash: SHA1
>
> Isn't this normally called the "OYE-0001" ? not "OY-0001" ? The website
> and all literature I've seen uses the "OYE-0001" name...
>
> Regardless, in many places, you have not followed the existing
> alphabetical order.
>
> LiWeijian <younfan33 at hotmail.com> wrote:
> > From: Tom Deng <2579131212 at qq.com>
> >
> > Adding support for OY-0001 Wireless Router.
> > OY-0001 is a wireless router made by oyewifi.com. Below is the details:
> > MT7620A, 128MB DDR2, 16MB FLASH, SD Slot, USB 2.0, 4 x LAN + 1 x WAN.
> > Signed-off-by: Tom Deng <2579131212 at qq.com>
> > ---
> > diff --git a/target/linux/ramips/base-files/etc/board.d/01_leds
> > b/target/linux/ramips/base-files/etc/board.d/01_leds
> > index 545bd70..fe3a79d 100755
> > --- a/target/linux/ramips/base-files/etc/board.d/01_leds
> > +++ b/target/linux/ramips/base-files/etc/board.d/01_leds
> > @@ -238,6 +238,10 @@ case $board in
> > set_wifi_led "zbtlink:blue:air"
> > set_usb_led "zbtlink:blue:usb"
> > ;;
> > + oy-0001)
> > + ucidef_set_led_default "power" "power" "oy:green:power" "1"
> > + set_wifi_led "oy:green:wifi"
> > + ;;
> > wr8305rt)
> > ucidef_set_led_default "power" "power" "wr8305rt:sys" "1"
> > set_usb_led "wr8305rt:usb"
> > diff --git a/target/linux/ramips/base-files/etc/board.d/02_network
> > b/target/linux/ramips/base-files/etc/board.d/02_network
> > index bc1fc01..9fb3535 100755
> > --- a/target/linux/ramips/base-files/etc/board.d/02_network
> > +++ b/target/linux/ramips/base-files/etc/board.d/02_network
> > @@ -139,6 +139,7 @@ ramips_setup_interfaces()
> > mzk-750dhp | \
> > whr-300hp2 | \
> > whr-600d | \
> > + oy-0001 | \
> > wsr-600 | \
> > wsr-1166 | \
> > wt1520 | \
> > @@ -283,6 +284,11 @@ ramips_setup_macs()
> > wan_mac=$(mtd_get_mac_binary devdata 7)
> > ;;
> >
> > + oy-0001)
> > + lan_mac=$(mtd_get_mac_binary factory 40)
> > + wan_mac=$(mtd_get_mac_binary factory 46)
> > + ;;
> > +
> > w306r-v20)
> > lan_mac=$(cat /sys/class/net/eth0/address)
> > wan_mac=$(macaddr_add "$lan_mac" 5)
> > diff --git a/target/linux/ramips/base-files/lib/ramips.sh
> > b/target/linux/ramips/base-files/lib/ramips.sh
> > index d2a1856..3d40ab9 100755
> > --- a/target/linux/ramips/base-files/lib/ramips.sh
> > +++ b/target/linux/ramips/base-files/lib/ramips.sh
> > @@ -400,6 +400,9 @@ ramips_board_detect() {
> > *"Zbtlink ZBT-WA05")
> > name="zbt-wa05"
> > ;;
> > + *"OY-0001")
> > + name="oy-0001"
> > + ;;
> > *"ZBT WR8305RT")
> > name="wr8305rt"
> > ;;
> > diff --git a/target/linux/ramips/base-files/lib/upgrade/platform.sh
> > b/target/linux/ramips/base-files/lib/upgrade/platform.sh
> > index cedd62b..8f45a84 100755
> > --- a/target/linux/ramips/base-files/lib/upgrade/platform.sh
> > +++ b/target/linux/ramips/base-files/lib/upgrade/platform.sh
> > @@ -116,6 +116,7 @@ platform_check_image() {
> > wr6202 |\
> > wr8305rt |\
> > wrtnode |\
> > + oy-0001 |\
> > wt1520 |\
> > wt3020 |\
> > x5 |\
> > diff --git a/target/linux/ramips/dts/OY-0001.dts
> > b/target/linux/ramips/dts/OY-0001.dts
> > new file mode 100644
> > index 0000000..48b7099
> > --- /dev/null
> > +++ b/target/linux/ramips/dts/OY-0001.dts
> > @@ -0,0 +1,123 @@
> > +/dts-v1/;
> > +
> > +/include/ "mt7620a.dtsi"
> > +
> > +/ {
> > + compatible = "ralink,mt7620a-soc";
> > + model = "OY-0001";
> > +
> > + chosen {
> > + bootargs = "console=ttyS0,115200";
> > + };
> > +
> > + palmbus at 10000000 {
> > + gpio2: gpio at 660 {
> > + status = "okay";
> > + };
> > +
> > + gpio3: gpio at 688 {
> > + status = "okay";
> > + };
> > +
> > + spi at b00 {
> > + status = "okay";
> > +
> > + m25p80 at 0 {
> > + #address-cells = <1>;
> > + #size-cells = <1>;
> > + compatible = "w25q128";
> > + reg = <0 0>;
> > + linux,modalias = "m25p80", "w25q128";
> > + spi-max-frequency = <10000000>;
> > +
> > + partition at 0 {
> > + label = "u-boot";
> > + reg = <0x0 0x30000>;
> > + read-only;
> > + };
> > +
> > + partition at 30000 {
> > + label = "u-boot-env";
> > + reg = <0x30000 0x10000>;
> > + read-only;
> > + };
> > +
> > + factory: partition at 40000 {
> > + label = "factory";
> > + reg = <0x40000 0x10000>;
> > + read-only;
> > + };
> > +
> > + partition at 50000 {
> > + label = "firmware";
> > + reg = <0x50000 0xfb0000>;
> > + };
> > +
> > + };
> > + };
> > + };
> > +
> > + pinctrl {
> > + state_default: pinctrl0 {
> > + gpio {
> > + ralink,group = "i2c", "uartf", "rgmii1", "rgmii2", "wled", "nd_sd";
> > + ralink,function = "gpio";
> > + };
> > + };
> > + };
> > +
> > + ethernet at 10100000 {
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&ephy_pins>;
> > +
> > + ralink,port-map = "llllw";
> > + };
> > +
> > + gsw at 10110000 {
> > + ralink,port4 = "ephy";
> > + };
> > +
> > + wmac at 10180000 {
> > + ralink,mtd-eeprom = <&factory 0>;
> > + };
> > +
> > + gpio-leds {
> > + compatible = "gpio-leds";
> > + powerled {
> > + label = "oy:green:power";
> > + gpios = <&gpio0 9 1>;
> > + };
> > + wifiled {
> > + label = "oy:green:wifi";
> > + gpios = <&gpio3 0 1>;
> > + };
> > + };
> > +
> > + sdhci at 10130000 {
> > + status = "okay";
> > + };
> > +
> > + ehci at 101c0000 {
> > + status = "okay";
> > + };
> > +
> > + ohci at 101c1000 {
> > + status = "okay";
> > + };
> > +
> > + pcie at 10140000 {
> > + status = "okay";
> > + };
> > +
> > + gpio-keys-polled {
> > + compatible = "gpio-keys-polled";
> > + #address-cells = <1>;
> > + #size-cells = <0>;
> > + poll-interval = <20>;
> > + s1 {
> > + label = "reset";
> > + gpios = <&gpio0 1 1>;
> > + linux,code = <0x198>;
> > + };
> > + };
> > +};
> > diff --git a/target/linux/ramips/image/Makefile
> > b/target/linux/ramips/image/Makefile
> > index 0c28216..2fe5fdd 100644
> > --- a/target/linux/ramips/image/Makefile
> > +++ b/target/linux/ramips/image/Makefile
> > @@ -866,6 +866,7 @@ Image/Build/Profile/DIR-810L=$(call BuildFirmware/CustomFlash/$(1),$(1),dir-810l
> > na930_mtd_size=20971520
> > Image/Build/Profile/NA930=$(call BuildFirmware/CustomFlash/$(1),$(1),na930,NA930,$(na930_mtd_size))
> > Image/Build/Profile/MZK-750DHP=$(call BuildFirmware/Default8M/$(1),$(1),mzk-750dhp,MZK-750DHP)
> > +Image/Build/Profile/OY-0001=$(call BuildFirmware/Default16M/$(1),$(1),oy-0001,OY-0001)
> > Image/Build/Profile/Y1=$(call BuildFirmware/Default16M/$(1),$(1),Lenovo-y1,Y1)
> > Image/Build/Profile/Y1S=$(call BuildFirmware/Default16M/$(1),$(1),Lenovo-y1s,Y1S)
> > Image/Build/Profile/MLW221=$(call BuildFirmware/Default16M/$(1),$(1),mlw221,MLW221)
> > @@ -899,6 +900,7 @@ define Image/Build/Profile/Default
> > $(call Image/Build/Profile/WHR1166D,$(1))
> > $(call Image/Build/Profile/MZK-750DHP,$(1))
> > $(call Image/Build/Profile/NA930,$(1))
> > + $(call Image/Build/Profile/OY-0001,$(1))
> > $(call Image/Build/Profile/Y1,$(1))
> > $(call Image/Build/Profile/Y1S,$(1))
> > $(call Image/Build/Profile/MLW221,$(1))
> > _______________________________________________
> > openwrt-devel mailing list
> > openwrt-devel at lists.openwrt.org
> > https://lists.openwrt.org/cgi-bin/mailman/listinfo/openwrt-devel
>
> - --
> Sent using Mailpile, Free Software from www.mailpile.is
>
> -----BEGIN PGP SIGNATURE-----
> Version: GnuPG v1.4.11 (GNU/Linux)
>
> iQIcBAEBAgAGBQJVn6w8AAoJEBmotQ/U1cr2IxwQAJcAJAAU3Xxq13eDCZ7+DaV/
> OTV1SusODWC++4eJ4HxaDFJ6r4RKVo/0B5f8i70HLz+I2r4dWM60E8J7shWoaSsv
> K+aV/pUj50klZuzAXpekDitezYSRi2m7l40IcMrF29x+PZYzr6bdeiJOp+BkTrKh
> oo7NN9QykgMwmZy+LoKdgoGtwgIWa1oxZHY1ppI2CCIbGiis+eeusyqp6kPvLUee
> y4dzGTFk3oend3LP1DGpW8MmOXFVaCksQIs3RhTGgc2IUQ0dpIpbDYVA3MnaRq95
> s824pG++vE0iCnWrpK9ij518GFvRvhn4kTaE6Xy0T/LmgDKq4DGpCZ3en0dVYzeJ
> Ln/FyIwvuALFkPEr2WqWXEAvPIPyuUxViOXpL5XRhGQ1Grnhzl0vwMRzKXq6VBus
> QvWVzREupNygD+3iHcJ93zOJFSF+AuvlU5JRS+88Lg8URmX8gEC+R7hulO8Cs2Uc
> 0TXg1tYmoUS3AJFZWUebQIlvX66gXHYZs+jTMM1zHRSrZ0Xn6DVUFEQ3oxcuhl2k
> 12/sGJusstgMyT30HLPLUHBb7fuw7T7f3149uyi4c8L5WYuzo+fNcbSFckBcP4Cw
> jTSjr960T1fBfIXTn/Mj7zlDsk3ntzImNg0uwgohqt2SjLUOR20zPhfrgGXT4fN5
> T7K9ToSMM4QcGLaSx0ry
> =Qc6u
> -----END PGP SIGNATURE-----
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://lists.infradead.org/pipermail/openwrt-devel/attachments/20150710/535fdb41/attachment.htm>
-------------- next part --------------
_______________________________________________
openwrt-devel mailing list
openwrt-devel at lists.openwrt.org
https://lists.openwrt.org/cgi-bin/mailman/listinfo/openwrt-devel
More information about the openwrt-devel
mailing list