[OpenWrt-Devel] [PATCH 1/3] [Lantiq] [P2812HNUFX] Remove old dts
John Crispin
blogic at openwrt.org
Thu Jan 8 15:30:56 EST 2015
On 27/12/2014 11:32, Sylwester Petela wrote:
> Remove unused P2812HNUFX board definition.
>
> Signed-off-by: Sylwester Petela <sscapi at gmail.com>
> ---
please change the patch to
* make use of 1 dtsi file and 2 dts files
* after applying your patch 1/3 the tree will not build. please remove
old file at the end of the series
>
> --- a/target/linux/lantiq/dts/P2812HNUFX.dts
> +++ /dev/null
> @@ -1,308 +0,0 @@
> -/dts-v1/;
> -
> -/include/ "vr9.dtsi"
> -
> -/ {
> - model = "P2812HNUFX - ZyXEL P-2812HNU-Fx";
> -
> - chosen {
> - /*bootargs = "console=ttyLTQ0,115200 init=/etc/preinit";*/
> - };
> -
> - memory at 0 {
> - reg = <0x0 0x8000000>;
> - };
> -
> - fpi at 10000000 {
> - #address-cells = <1>;
> - #size-cells = <1>;
> - compatible = "lantiq,fpi", "simple-bus";
> - ranges = <0x0 0x10000000 0xEEFFFFF>;
> - reg = <0x10000000 0xEF00000>;
> -
> - localbus at 0 {
> - #address-cells = <2>;
> - #size-cells = <1>;
> - compatible = "lantiq,localbus", "simple-bus";
> -
> - nand-parts at 0 {
> - compatible = "gen_nand", "lantiq,nand-xway";
> - lantiq,cs = <1>;
> - bank-width = <2>;
> - reg = <0 0x0 0x2000000>;
> - #address-cells = <1>;
> - #size-cells = <1>;
> -
> - partition at 0 {
> - label = "u-boot";
> - reg = <0x00000 0x40000>;
> - };
> -
> - partition at 40000 {
> - label = "u-boot environment";
> - reg = <0x40000 0x20000>;
> - };
> -
> - partition at 60000 {
> - label = "root";
> - reg = <0x60000 0x7fa0000>;
> - };
> - };
> - };
> -
> - gpio: pinmux at E100B10 {
> - compatible = "lantiq,pinctrl-xr9";
> - pinctrl-names = "default";
> - pinctrl-0 = <&state_default>;
> -
> - interrupt-parent = <&icu0>;
> - interrupts = <166 135 66 40 41 42 38>;
> -
> - #gpio-cells = <2>;
> - gpio-controller;
> - reg = <0xE100B10 0xA0>;
> -
> - state_default: pinmux {
> - mdio {
> - lantiq,groups = "mdio";
> - lantiq,function = "mdio";
> - };
> - gphy-leds {
> - lantiq,groups = "gphy0 led1", "gphy1 led1",
> - "gphy0 led2", "gphy1 led2";
> - lantiq,function = "gphy";
> - lantiq,pull = <2>;
> - lantiq,open-drain = <0>;
> - lantiq,output = <1>;
> - };
> - stp {
> - lantiq,groups = "stp";
> - lantiq,function = "stp";
> - lantiq,pull = <2>;
> - lantiq,open-drain = <0>;
> - lantiq,output = <1>;
> - };
> - pci {
> - lantiq,groups = "gnt1", "req1";
> - lantiq,function = "pci";
> - };
> - pci-rst {
> - lantiq,pins = "io21";
> - lantiq,pull = <0>;
> - lantiq,open-drain = <0>;
> - lantiq,output = <1>;
> - };
> - ifxhcd-rst {
> - lantiq,pins = "io33";
> - lantiq,pull = <0>;
> - lantiq,open-drain = <0>;
> - lantiq,output = <1>;
> - };
> - nand {
> - lantiq,groups = "nand cle", "nand ale",
> - "nand rd", "nand cs1", "nand rdy";
> - lantiq,function = "ebu";
> - lantiq,pull = <1>;
> - };
> - };
> - };
> -
> - eth at E108000 {
> - #address-cells = <1>;
> - #size-cells = <0>;
> - compatible = "lantiq,xrx200-net";
> - reg = < 0xE108000 0x3000 /* switch */
> - 0xE10B100 0x70 /* mdio */
> - 0xE10B1D8 0x30 /* mii */
> - 0xE10B308 0x30 /* pmac */
> - >;
> - interrupt-parent = <&icu0>;
> - interrupts = <73 72>;
> -
> - lan: interface at 0 {
> - compatible = "lantiq,xrx200-pdi";
> - #address-cells = <1>;
> - #size-cells = <0>;
> - reg = <0>;
> - mac-address = [ 00 11 22 33 44 55 ];
> - lantiq,switch;
> -
> - ethernet at 0 {
> - compatible = "lantiq,xrx200-pdi-port";
> - reg = <0>;
> - phy-mode = "rgmii";
> - phy-handle = <&phy0>;
> - };
> - ethernet at 1 {
> - compatible = "lantiq,xrx200-pdi-port";
> - reg = <1>;
> - phy-mode = "rgmii";
> - phy-handle = <&phy1>;
> - };
> - ethernet at 2 {
> - compatible = "lantiq,xrx200-pdi-port";
> - reg = <2>;
> - phy-mode = "gmii";
> - phy-handle = <&phy11>;
> - };
> - ethernet at 4 {
> - compatible = "lantiq,xrx200-pdi-port";
> - reg = <4>;
> - phy-mode = "gmii";
> - phy-handle = <&phy13>;
> - };
> - ethernet at 5 {
> - compatible = "lantiq,xrx200-pdi-port";
> - reg = <5>;
> - phy-mode = "rgmii";
> - phy-handle = <&phy5>;
> - };
> - };
> -
> - mdio at 0 {
> - #address-cells = <1>;
> - #size-cells = <0>;
> - compatible = "lantiq,xrx200-mdio";
> - phy0: ethernet-phy at 0 {
> - reg = <0x0>;
> - compatible = "lantiq,phy11g", "ethernet-phy-ieee802.3-c22";
> - };
> - phy1: ethernet-phy at 1 {
> - reg = <0x1>;
> - compatible = "lantiq,phy11g", "ethernet-phy-ieee802.3-c22";
> - };
> - phy5: ethernet-phy at 5 {
> - reg = <0x5>;
> - compatible = "lantiq,phy11g", "ethernet-phy-ieee802.3-c22";
> - };
> - phy11: ethernet-phy at 11 {
> - reg = <0x11>;
> - compatible = "lantiq,phy11g", "ethernet-phy-ieee802.3-c22";
> - };
> - phy13: ethernet-phy at 13 {
> - reg = <0x13>;
> - compatible = "lantiq,phy11g", "ethernet-phy-ieee802.3-c22";
> - };
> - };
> - };
> -
> - stp: stp at E100BB0 {
> - compatible = "lantiq,gpio-stp-xway";
> - reg = <0xE100BB0 0x40>;
> - #gpio-cells = <2>;
> - gpio-controller;
> -
> - lantiq,shadow = <0xffffff>;
> - lantiq,groups = <0x7>;
> - /*
> - lantiq,dsl = <0x3>;
> - lantiq,phy1 = <0x7>;
> - lantiq,phy2 = <0x7>;
> - */
> - };
> -
> - ifxhcd at E101000 {
> - status = "okay";
> - gpios = <&gpio 33 0>;
> - lantiq,portmask = <0x3>;
> - };
> -
> - pci at E105400 {
> - lantiq,bus-clock = <33333333>;
> - /* lantiq,external-clock; */
> - lantiq,delay-hi = <0>; /* 0ns delay */
> - lantiq,delay-lo = <0>; /* 0.0ns delay */
> - interrupt-map-mask = <0xf800 0x0 0x0 0x7>;
> - interrupt-map = <
> - 0x7000 0 0 1 &icu0 29 //1 // slot 14, irq 29
> - >;
> - gpio-reset = <&gpio 21 0>;
> - req-mask = <0x1>; /* GNT1 */
> - status = "okay";
> - };
> - };
> -
> - gphy-xrx200 {
> - compatible = "lantiq,phy-xrx200";
> - firmware = "lantiq/vr9_phy11g_a1x.bin";
> - phys = [ 00 01 ];
> - };
> -
> - gpio-keys-polled {
> - compatible = "gpio-keys-polled";
> - #address-cells = <1>;
> - #size-cells = <0>;
> - poll-interval = <100>;
> - reset {
> - label = "reset";
> - gpios = <&gpio 39 1>;
> - linux,code = <0x198>;
> - };
> - rfkill {
> - label = "rfkill";
> - gpios = <&gpio 1 1>;
> - linux,code = <0xf7>;
> - };
> - };
> -
> - gpio-leds {
> - compatible = "gpio-leds";
> -
> - internet2 {
> - label = "internet2";
> - gpios = <&stp 16 1>;
> - };
> - internet {
> - label = "internet";
> - gpios = <&stp 17 1>;
> - };
> - dsl {
> - label = "dsl";
> - gpios = <&stp 18 1>;
> - };
> - dsl2 {
> - label = "dsl2";
> - gpios = <&stp 19 1>;
> - };
> - wifi2 {
> - label = "wifi2";
> - gpios = <&stp 20 1>;
> - };
> - wlan {
> - label = "wifi";
> - gpios = <&stp 21 1>;
> - };
> - power2 {
> - label = "power2";
> - gpios = <&stp 22 1>;
> - };
> - power {
> - label = "power";
> - gpios = <&stp 23 1>;
> - };
> - usb1 {
> - label = "usb";
> - gpios = <&gpio 38 1>;
> - };
> - usb2 {
> - label = "usb2";
> - gpios = <&gpio 44 1>;
> - };
> - phone1 {
> - label = "phone1";
> - gpios = <&gpio 11 1>;
> - };
> - phone1warn {
> - label = "phone1warn";
> - gpios = <&gpio 12 1>;
> - };
> - phone2 {
> - label = "phone2";
> - gpios = <&gpio 28 1>;
> - };
> - phone2warn {
> - label = "phone2warn";
> - gpios = <&gpio 26 1>;
> - };
> - };
> -};
> _______________________________________________
> openwrt-devel mailing list
> openwrt-devel at lists.openwrt.org
> https://lists.openwrt.org/cgi-bin/mailman/listinfo/openwrt-devel
>
_______________________________________________
openwrt-devel mailing list
openwrt-devel at lists.openwrt.org
https://lists.openwrt.org/cgi-bin/mailman/listinfo/openwrt-devel
More information about the openwrt-devel
mailing list