[OpenWrt-Devel] Ubiquiti Rocket M5 build
Ken Buska
kbuska at gmail.com
Tue Feb 17 14:26:58 EST 2015
I tested both the loco nw and nano nw builds and below is the boot for the
loco nw build. I was able to bring the lan interface up running the
following commands and although I can ping myself, I can't ping another
other devices. I also don't learn any macs from the connected switch.
U-Boot 1.1.4-s776 (Nov 27 2013 - 15:58:45)
Board: Ubiquiti Networks AR9342 board (e6b5-30247.1122.0030)
Reset: Normal
DRAM: 64 MB
Flash: 8 MB (0xc2, 0x20, 0x17)
Net: AR8035
eth0, eth1
Radio: 0777:e6b5
Hit any key to stop autoboot: 0
## Booting image at 9f050000 ...
Image Name: MIPS OpenWrt Linux-3.14.32
Created: 2015-02-15 9:46:26 UTC
Image Type: MIPS Linux Kernel Image (lzma compressed)
Data Size: 1163425 Bytes = 1.1 MB
Load Address: 80060000
Entry Point: 80060000
Verifying Checksum at 0x9f050040 ...OK
Uncompressing Kernel Image ... OK
Starting kernel ...
[ 0.000000] Linux version 3.14.32 (openwrt at snapon) (gcc version 4.8.3 (
OpenWrt/Linaro GCC 4.8-2014.04 r44455) ) #1 Sun Feb
15 01:43:18 PST 2015
[ 0.000000] bootconsole [early0] enabled
[ 0.000000] CPU0 revision is: 0001974c (MIPS 74Kc)
[ 0.000000] SoC: Atheros AR9342 rev 2
[ 0.000000] Determined physical RAM map:
[ 0.000000] memory: 04000000 @ 00000000 (usable)
[ 0.000000] Initrd not found or empty - disabling initrd
[ 0.000000] Zone ranges:
[ 0.000000] Normal [mem 0x00000000-0x03ffffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x00000000-0x03ffffff]
[ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32
bytes.
[ 0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases,
linesize 32 bytes
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on.
Total pages: 16256
[ 0.000000] Kernel command line: board=UBNT-NM-XW console=ttyS0,115200
mtdparts=spi0.0:256k(u-boot)ro,64k(u-boot-env)ro,7
552k(firmware),256k(cfg)ro,64k(EEPROM)ro
rootfstype=squashfs,jffs2 noinitrd
[ 0.000000] PID hash table entries: 256 (order: -2, 1024 bytes)
[ 0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.000000] Writing ErrCtl register=00000000
[ 0.000000] Readback ErrCtl register=00000000
[ 0.000000] Memory: 60944K/65536K available (2521K kernel code, 123K
rwdata, 520K rodata, 220K init, 191K bss, 4592K reser
ved)
[ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.000000] NR_IRQS:51
[ 0.000000] Clocks: CPU:535.000MHz, DDR:400.000MHz, AHB:200.000MHz,
Ref:40.000MHz
[ 0.000000] Calibrating delay loop... 266.64 BogoMIPS (lpj=1333248)
[ 0.080000] pid_max: default: 32768 minimum: 301
[ 0.080000] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.090000] Mountpoint-cache hash table entries: 1024 (order: 0, 4096
bytes)
[ 0.100000] NET: Registered protocol family 16
[ 0.100000] MIPS: machine is Ubiquiti Nanostation M XW
[ 0.330000] bio: create slab <bio-0> at 0
[ 0.340000] Switched to clocksource MIPS
[ 0.350000] NET: Registered protocol family 2
[ 0.350000] TCP established hash table entries: 1024 (order: 0, 4096
bytes)
[ 0.360000] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.360000] TCP: Hash tables configured (established 1024 bind 1024)
[ 0.370000] TCP: reno registered
[ 0.370000] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 0.380000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 0.380000] NET: Registered protocol family 1
[ 0.390000] futex hash table entries: 256 (order: -1, 3072 bytes)
[ 0.410000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.420000] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME)
(CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 0.430000] msgmni has been set to 119
[ 0.440000] io scheduler noop registered
[ 0.440000] io scheduler deadline registered (default)
[ 0.440000] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
[ 0.480000] serial8250.0: ttyS0 at MMIO 0x18020000 (irq = 11, base_baud
= 2500000) is a 16550A
[ 0.490000] console [ttyS0] enabled
[ 0.490000] console [ttyS0] enabled
[ 0.490000] bootconsole [early0] disabled
[ 0.490000] bootconsole [early0] disabled
[ 0.510000] m25p80 spi0.0: found mx25l6405d, expected m25p80
[ 0.510000] m25p80 spi0.0: mx25l6405d (8192 Kbytes)
[ 0.520000] 5 cmdlinepart partitions found on MTD device spi0.0
[ 0.520000] Creating 5 MTD partitions on "spi0.0":
[ 0.530000] 0x000000000000-0x000000040000 : "u-boot"
[ 0.540000] 0x000000040000-0x000000050000 : "u-boot-env"
[ 0.540000] 0x000000050000-0x0000007b0000 : "firmware"
[ 0.570000] 2 uimage-fw partitions found on MTD device firmware
[ 0.570000] 0x000000050000-0x00000016c0e1 : "kernel"
[ 0.580000] mtd: partition "kernel" must either start or end on erase
block boundary or be smaller than an erase block --
forcing read-only
[ 0.590000] 0x00000016c0e1-0x0000007b0000 : "rootfs"
[ 0.600000] mtd: partition "rootfs" must either start or end on erase
block boundary or be smaller than an erase block --
forcing read-only
[ 0.610000] mtd: device 4 (rootfs) set to be root filesystem
[ 0.620000] 1 squashfs-split partitions found on MTD device rootfs
[ 0.620000] 0x000000350000-0x0000007b0000 : "rootfs_data"
[ 0.630000] 0x0000007b0000-0x0000007f0000 : "cfg"
[ 0.640000] 0x0000007f0000-0x000000800000 : "EEPROM"
[ 0.650000] libphy: ag71xx_mdio: probed
[ 1.250000] ag71xx ag71xx.0: no PHY found with phy_mask=00000023
[ 1.260000] TCP: cubic registered
[ 1.260000] NET: Registered protocol family 17
[ 1.260000] Bridge firewalling registered
[ 1.270000] 8021q: 802.1Q VLAN Support v1.8
[ 1.280000] VFS: Mounted root (squashfs filesystem) readonly on device
31:4.
[ 1.290000] Freeing unused kernel memory: 220K (80379000 - 803b0000)
procd: Console is alive
procd: - watchdog -
[ 3.520000] usbcore: registered new interface driver usbfs
[ 3.530000] usbcore: registered new interface driver hub
[ 3.540000] usbcore: registered new device driver usb
[ 3.550000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 3.550000] ehci-platform: EHCI generic platform driver
[ 3.560000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 3.570000] ohci-platform: OHCI generic platform driver
procd: - preinit -
[ 4.880000] random: mktemp urandom read with 48 bits of entropy available
Press the [f] key and hit [enter] to enter failsafe mode
Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level
jffs2 is not ready - marker found
procd: - early -
procd: - watchdog -
procd: - ubus -
procd: - init -
Please press Enter to activate this console.
[ 10.750000] NET: Registered protocol family 10
[ 10.760000] ip6_tables: (C) 2000-2006 Netfilter Core Team
[ 10.770000] Loading modules backported from Linux version
master-2014-11-04-0-gf3660a2
[ 10.780000] Backport generated by backports.git
backports-20141023-2-g4ff890b
[ 10.790000] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 10.810000] nf_conntrack version 0.5.0 (955 buckets, 3820 max)
[ 10.860000] xt_time: kernel timezone is -0000
[ 10.890000] cfg80211: Calling CRDA to update world regulatory domain
[ 10.890000] cfg80211: World regulatory domain updated:
[ 10.900000] cfg80211: DFS Master region: unset
[ 10.900000] cfg80211: (start_freq - end_freq @ bandwidth),
(max_antenna_gain, max_eirp), (dfs_cac_time)
[ 10.910000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A,
2000 mBm), (N/A)
[ 10.920000] cfg80211: (2457000 KHz - 2482000 KHz @ 40000 KHz), (N/A,
2000 mBm), (N/A)
[ 10.930000] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (N/A,
2000 mBm), (N/A)
[ 10.940000] cfg80211: (5170000 KHz - 5250000 KHz @ 80000 KHz), (N/A,
2000 mBm), (N/A)
[ 10.950000] cfg80211: (5250000 KHz - 5330000 KHz @ 80000 KHz, 160000
KHz AUTO), (N/A, 2000 mBm), (0 s)
[ 10.960000] cfg80211: (5490000 KHz - 5730000 KHz @ 160000 KHz), (N/A,
2000 mBm), (0 s)
[ 10.960000] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A,
2000 mBm), (N/A)
[ 10.970000] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz),
(N/A, 0 mBm), (N/A)
[ 11.050000] PPP generic driver version 2.4.2
[ 11.070000] NET: Registered protocol family 24
[ 11.150000] cfg80211: Calling CRDA for country: US
[ 11.160000] cfg80211: Regulatory domain changed to country: US
[ 11.160000] cfg80211: DFS Master region: FCC
[ 11.170000] cfg80211: (start_freq - end_freq @ bandwidth),
(max_antenna_gain, max_eirp), (dfs_cac_time)
[ 11.180000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A,
3000 mBm), (N/A)
[ 11.180000] cfg80211: (5170000 KHz - 5250000 KHz @ 80000 KHz, 160000
KHz AUTO), (N/A, 1700 mBm), (N/A)
[ 11.190000] cfg80211: (5250000 KHz - 5330000 KHz @ 80000 KHz, 160000
KHz AUTO), (N/A, 2300 mBm), (0 s)
[ 11.200000] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A,
3000 mBm), (N/A)
[ 11.210000] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz),
(N/A, 4000 mBm), (N/A)
[ 11.220000] ieee80211 phy0: Atheros AR9340 Rev:2 mem=0xb8100000, irq=47
[ 17.570000] jffs2_scan_eraseblock(): End of filesystem marker found at
0x0
[ 17.600000] jffs2_build_filesystem(): unlocking the mtd device... done.
[ 17.600000] jffs2_build_filesystem(): erasing all blocks after the end
marker...
[ 34.290000] random: nonblocking pool is initialized
[ 49.260000] done.
[ 49.270000] jffs2: notice: (899) jffs2_build_xattr_subsystem: complete
building xattr subsystem, 0 of xdatum (0 unchecked,
0 orphan) and 0 of xref (0 dead, 0 orphan) found.
procd: - init complete -
uci set wireless.radio0.disabled=1
uci get wireless.radio0.disabled=1
uci set wireless.radio0.disabled=0
uci get wireless.radio0.disabled=0
ifup lan
Thank you,
On Sat, Feb 14, 2015 at 11:40 AM, Saverio Proto <zioproto at gmail.com> wrote:
> I think the one for the NanoStation should work as well:
>
> http://downloads.openwrt.org/barrier_breaker/14.07/ar71xx/generic/openwrt-ar71xx-generic-ubnt-nano-m-xw-squashfs-factory.bin
>
> I never tested, but ubnt devices are all similar.
>
> Saverio
>
>
> 2015-02-12 21:27 GMT+01:00 Ken Buska <kbuska at gmail.com>:
> > Is there anyone that is able to help create a build for the Rocket M5 XW
> > build?
> >
> > --
> > Thank you,
> > Ken Buska
> >
> >
> > _______________________________________________
> > openwrt-devel mailing list
> > openwrt-devel at lists.openwrt.org
> > https://lists.openwrt.org/cgi-bin/mailman/listinfo/openwrt-devel
> >
>
--
Thank you,
Ken Buska
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://lists.infradead.org/pipermail/openwrt-devel/attachments/20150217/17e701ed/attachment.htm>
-------------- next part --------------
_______________________________________________
openwrt-devel mailing list
openwrt-devel at lists.openwrt.org
https://lists.openwrt.org/cgi-bin/mailman/listinfo/openwrt-devel
More information about the openwrt-devel
mailing list