[OpenWrt-Devel] lantiq v3.18
Joerg Hollmann
Joerg.Hollmann at t-online.de
Tue Feb 10 13:35:20 EST 2015
Hello Daniel,
could it be, that the definition of the kernel partition in the dts file
of your device ist too small?
I have seen similar error messages on the builds for the VG3503J.
Regards,
Joerg
On 02/10/2015 10:40 AM, Daniel Gimpelevich wrote:
> Is there a patchset I could try?
>
> On Mon, 2015-02-09 at 12:44 -0800, Daniel Gimpelevich wrote:
>> On Mon, 2015-02-09 at 21:27 +0100, John Crispin wrote:
>>> bootlog please
>>>
>>> On 09/02/2015 21:25, Daniel Gimpelevich wrote:
>>>> On Mon, 2015-02-09 at 19:18 +0100, John Crispin wrote:
>>>>> try r44366 or newer please
>>>> SPI flash is not detected, bricking the device.
>>>>
>> [ 0.000000] Linux version 3.18.6 (danielg4 at chimera) (gcc version 4.8.3 (OpenWrt/Linaro GCC 4.8-2014.04 r43982) ) #3 Mon Feb 9 115
>> [ 0.000000] SoC: AR9 rev 1.2
>> [ 0.000000] bootconsole [early0] enabled
>> [ 0.000000] CPU0 revision is: 0001954c (MIPS 34Kc)
>> [ 0.000000] MIPS: machine is DGN3500 - Netgear DGN3500
>> [ 0.000000] Determined physical RAM map:
>> [ 0.000000] memory: 04000000 @ 00000000 (usable)
>> [ 0.000000] User-defined physical RAM map:
>> [ 0.000000] memory: 04000000 @ 00000000 (usable)
>> [ 0.000000] Initrd not found or empty - disabling initrd
>> [ 0.000000] Zone ranges:
>> [ 0.000000] Normal [mem 0x00000000-0x03ffffff]
>> [ 0.000000] Movable zone start for each node
>> [ 0.000000] Early memory node ranges
>> [ 0.000000] node 0: [mem 0x00000000-0x03ffffff]
>> [ 0.000000] Initmem setup node 0 [mem 0x00000000-0x03ffffff]
>> [ 0.000000] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
>> [ 0.000000] Primary data cache 16kB, 4-way, VIPT, no aliases, linesize 32 bytes
>> [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 16256
>> [ 0.000000] Kernel command line: root=/dev/mtdblock0 ip=192.168.1.1:192.168.1.15::::eth0:on console=ttyS1,115200 ethaddr=30:46:90
>> [ 0.000000] PID hash table entries: 256 (order: -2, 1024 bytes)
>> [ 0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
>> [ 0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
>> [ 0.000000] Writing ErrCtl register=00005880
>> [ 0.000000] Readback ErrCtl register=00005880
>> [ 0.000000] Memory: 60404K/65536K available (3312K kernel code, 147K rwdata, 664K rodata, 144K init, 194K bss, 5132K reserved)
>> [ 0.000000] NR_IRQS:256
>> [ 0.000000] CPU Clock: 333MHz
>> [ 0.000000] Calibrating delay loop... 221.18 BogoMIPS (lpj=442368)
>> [ 0.036000] pid_max: default: 32768 minimum: 301
>> [ 0.040000] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
>> [ 0.044000] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
>> [ 0.052000] pinctrl core: initialized pinctrl subsystem
>> [ 0.056000] NET: Registered protocol family 16
>> [ 0.064000] pinctrl-xway 1e100b10.pinmux: Init done
>> [ 0.068000] dma-xway 1e104100.dma: Init done - hw rev: 6, ports: 5, channels: 20
>> [ 0.076000] PCI host bridge /fpi at 10000000/pci at E105400 ranges:
>> [ 0.080000] MEM 0x0000000018000000..0x0000000019ffffff
>> [ 0.084000] IO 0x000000001ae00000..0x000000001affffff
>> [ 0.088000] ath9k,eeprom ath9k_eep: failed to load eeprom address
>> [ 0.100000] usbcore: registered new interface driver usbfs
>> [ 0.104000] usbcore: registered new interface driver hub
>> [ 0.108000] usbcore: registered new device driver usb
>> [ 0.112000] PCI host bridge to bus 0000:00
>> [ 0.116000] pci_bus 0000:00: root bus resource [mem 0x18000000-0x19ffffff]
>> [ 0.120000] pci_bus 0000:00: root bus resource [io 0xffffffff]
>> [ 0.124000] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
>> [ 0.128000] pci 0000:00:0e.0: BAR 0: assigned [mem 0x18000000-0x1800ffff]
>> [ 0.132000] Switched to clocksource MIPS
>> [ 0.136000] NET: Registered protocol family 2
>> [ 0.144000] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
>> [ 0.148000] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
>> [ 0.156000] TCP: Hash tables configured (established 1024 bind 1024)
>> [ 0.164000] TCP: reno registered
>> [ 0.164000] UDP hash table entries: 256 (order: 0, 4096 bytes)
>> [ 0.172000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
>> [ 0.180000] NET: Registered protocol family 1
>> [ 0.184000] gptu: totally 6 16-bit timers/counters
>> [ 0.188000] gptu: misc_register on minor 63
>> [ 0.192000] gptu: succeeded to request irq 126
>> [ 0.196000] gptu: succeeded to request irq 127
>> [ 0.200000] gptu: succeeded to request irq 128
>> [ 0.204000] gptu: succeeded to request irq 129
>> [ 0.212000] gptu: succeeded to request irq 130
>> [ 0.216000] gptu: succeeded to request irq 131
>> [ 0.220000] futex hash table entries: 256 (order: -1, 3072 bytes)
>> [ 0.228000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
>> [ 0.236000] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
>> [ 0.248000] msgmni has been set to 117
>> [ 0.252000] io scheduler noop registered
>> [ 0.256000] io scheduler deadline registered (default)
>> [ 0.260000] 1e100c00.serial: ttyLTQ0 at MMIO 0x1e100c00 (irq = 112, base_baud = 0) is a lantiq,asc
>> [ 0.268000] console [ttyLTQ0] enabled
>> [ 0.268000] console [ttyLTQ0] enabled
>> [ 0.276000] bootconsole [early0] disabled
>> [ 0.276000] bootconsole [early0] disabled
>> [ 0.332000] Realtek RTL8366RB ethernet switch driver version 0.2.4
>> [ 0.340000] rtl8366rb rtl8366rb: using GPIO pins 491 (SDA) and 493 (SCK)
>> [ 0.344000] rtl8366rb rtl8366rb: RTL5937 ver. 3 chip found
>> [ 0.440000] libphy: rtl8366rb: probed
>> [ 0.444000] libphy: ltq_mii: probed
>> [ 0.444000] eth0 (uninitialized): no PHY found
>> [ 0.452000] etop: mdio probe failed
>> [ 0.456000] wdt 1f8803f0.watchdog: Init done
>> [ 0.460000] TCP: cubic registered
>> [ 0.464000] NET: Registered protocol family 17
>> [ 0.468000] bridge: automatic filtering via arp/ip/ip6tables has been deprecated. Update your scripts to load br_netfilter if yo.
>> [ 0.480000] 8021q: 802.1Q VLAN Support v1.8
>> [ 0.484000] ath9k,eeprom ath9k_eep: failed to load eeprom address
>> [ 0.496000] UBIFS error (pid 1): ubifs_mount: cannot open "ubi0:rootfs", error -19
>> [ 0.504000] VFS: Cannot open root device "mtdblock5" or unknown-block(0,0): error -6
>> [ 0.508000] Please append a correct "root=" boot option; here are the available partitions:
>> [ 0.516000] Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(0,0)
>> [ 0.516000] Rebooting in 1 seconds..
> _______________________________________________
> openwrt-devel mailing list
> openwrt-devel at lists.openwrt.org
> https://lists.openwrt.org/cgi-bin/mailman/listinfo/openwrt-devel
>
_______________________________________________
openwrt-devel mailing list
openwrt-devel at lists.openwrt.org
https://lists.openwrt.org/cgi-bin/mailman/listinfo/openwrt-devel
More information about the openwrt-devel
mailing list