[OpenWrt-Devel] [Patch] ipq806x: add support for Netgear D7800
John Crispin
blogic at openwrt.org
Thu Dec 24 08:18:03 EST 2015
Hi,
your mail client replaced all tabs with spaces.
please consider using git to send patches. it will save you a lot of time.
John
On 24/12/2015 11:21, Tathagata Das wrote:
> Add support for the Netgear D7800 and build appropriate sysupgrade and
> factory images.
>
> Known issues:
> . USB ports are not working
> . DSL is not added
>
> Signed-off-by: Tathagata Das <tathagata at alumnux.com>
>
> ----
>
>> From 41487fc5f03abbd24c1a979c1c0e59a5f7da2898 Mon Sep 17 00:00:00 2001
> From: Tathagata Das <tathagata at alumnux.com>
> Date: Thu, 24 Dec 2015 09:44:01 +0530
> Subject: [PATCH] Added support for Netgear D7800
> Signed-off-by: Tathagata Das <tathagata at alumnux.com>
>
> ---
> .../linux/ipq806x/base-files/etc/board.d/01_leds | 1 +
> .../ipq806x/base-files/etc/board.d/02_network | 1 +
> target/linux/ipq806x/base-files/lib/ipq806x.sh | 3 +
> .../ipq806x/base-files/lib/upgrade/platform.sh | 2 +
> target/linux/ipq806x/image/Makefile | 13 +-
> ...dd-Netgear-Nighthawk-X4-D7800-device-tree.patch | 381
> ++++++++++++++++++++
> target/linux/ipq806x/profiles/netgear.mk | 14 +
> 7 files changed, 414 insertions(+), 1 deletions(-)
> create mode 100644
> target/linux/ipq806x/patches-3.18/801-ARM-qcom-add-Netgear-Nighthawk-X4-D7800-device-tree.patch
>
>
> diff --git a/target/linux/ipq806x/base-files/etc/board.d/01_leds
> b/target/linux/ipq806x/base-files/etc/board.d/01_leds
> index 07b5b06..b32c1cc 100755
> --- a/target/linux/ipq806x/base-files/etc/board.d/01_leds
> +++ b/target/linux/ipq806x/base-files/etc/board.d/01_leds
> @@ -11,6 +11,7 @@ board_config_update
> board=$(ipq806x_board_name)
>
> case "$board" in
> +d7800 |\
> r7500)
> ucidef_set_led_usbdev "usb1" "USB 1" "r7500:white:usb1" "1-1"
> ucidef_set_led_usbdev "usb2" "USB 2" "r7500:white:usb3" "3-1"
> diff --git a/target/linux/ipq806x/base-files/etc/board.d/02_network
> b/target/linux/ipq806x/base-files/etc/board.d/02_network
> index 1302a55..6e18297 100755
> --- a/target/linux/ipq806x/base-files/etc/board.d/02_network
> +++ b/target/linux/ipq806x/base-files/etc/board.d/02_network
> @@ -13,6 +13,7 @@ board=$(ipq806x_board_name)
>
> case "$board" in
> ap148 |\
> +d7800 |\
> r7500)
> ucidef_add_switch "switch0" \
> "1:lan" "2:lan" "3:lan" "4:lan" "6 at eth1" "5:wan" "0 at eth0"
> diff --git a/target/linux/ipq806x/base-files/lib/ipq806x.sh
> b/target/linux/ipq806x/base-files/lib/ipq806x.sh
> index 5b27bde..be48b9f 100644
> --- a/target/linux/ipq806x/base-files/lib/ipq806x.sh
> +++ b/target/linux/ipq806x/base-files/lib/ipq806x.sh
> @@ -20,6 +20,9 @@ ipq806x_board_detect() {
> *"DB149")
> name="db149"
> ;;
> + *"D7800")
> + name="d7800"
> + ;;
> *"R7500")
> name="r7500"
> ;;
> diff --git a/target/linux/ipq806x/base-files/lib/upgrade/platform.sh
> b/target/linux/ipq806x/base-files/lib/upgrade/platform.sh
> index c0e19a1..2400376 100644
> --- a/target/linux/ipq806x/base-files/lib/upgrade/platform.sh
> +++ b/target/linux/ipq806x/base-files/lib/upgrade/platform.sh
> @@ -7,6 +7,7 @@ platform_check_image() {
>
> case "$board" in
> AP148 |\
> + d7800 |\
> r7500)
> nand_do_platform_check $board $1
> return $?;
> @@ -21,6 +22,7 @@ platform_pre_upgrade() {
>
> case "$board" in
> AP148 |\
> + d7800 |\
> r7500)
> nand_do_upgrade "$1"
> ;;
> diff --git a/target/linux/ipq806x/image/Makefile
> b/target/linux/ipq806x/image/Makefile
> index 14cf442..8f46af8 100644
> --- a/target/linux/ipq806x/image/Makefile
> +++ b/target/linux/ipq806x/image/Makefile
> @@ -121,6 +121,17 @@ define Device/R7500
> BOARD_NAME := r7500
> endef
>
> -TARGET_DEVICES += AP148 AP148-legacy DB149 R7500
> +define Device/D7800
> + $(call Device/DniImage)
> + DEVICE_DTS := qcom-ipq8064-d7800
> + KERNEL_SIZE := 2097152
> + NETGEAR_BOARD_ID := D7800
> + NETGEAR_HW_ID := 29764958+0+128+512+4x4+4x4
> + BLOCKSIZE := 128KiB
> + PAGESIZE := 2048
> + BOARD_NAME := d7800
> +endef
> +
> +TARGET_DEVICES += AP148 AP148-legacy DB149 R7500 D7800
>
> $(eval $(call BuildImage))
> diff --git
> a/target/linux/ipq806x/patches-3.18/801-ARM-qcom-add-Netgear-Nighthawk-X4-D7800-device-tree.patch
> b/target/linux/ipq806x/patches-3.18/801-ARM-qcom-add-Netgear-Nighthawk-X4-D7800-device-tree.patch
>
> new file mode 100644
> index 0000000..ecc1cff
> --- /dev/null
> +++
> b/target/linux/ipq806x/patches-3.18/801-ARM-qcom-add-Netgear-Nighthawk-X4-D7800-device-tree.patch
>
> @@ -0,0 +1,381 @@
> +--- a/arch/arm/boot/dts/Makefile 2015-09-22 18:30:09.033530282 +0530
> ++++ b/arch/arm/boot/dts/Makefile 2015-09-23 17:06:44.892947581 +0530
> +@@ -362,6 +362,7 @@
> + qcom-ipq8064-ap148.dtb \
> + qcom-ipq8064-db149.dtb \
> + qcom-ipq8064-r7500.dtb \
> ++ qcom-ipq8064-d7800.dtb \
> + qcom-msm8660-surf.dtb \
> + qcom-msm8960-cdp.dtb \
> + qcom-msm8974-sony-xperia-honami.dtb
> +--- a/arch/arm/boot/dts/qcom-ipq8064-d7800.dts 1970-01-01
> 05:30:00.000000000 +0530
> ++++ b/arch/arm/boot/dts/qcom-ipq8064-d7800.dts 2015-09-23
> 17:06:45.336947567 +0530
> +@@ -0,0 +1,368 @@
> ++#include "qcom-ipq8064-v1.0.dtsi"
> ++
> ++#include <dt-bindings/input/input.h>
> ++
> ++/ {
> ++ model = "Netgear Nighthawk X4 D7800";
> ++ compatible = "netgear,d7800", "qcom,ipq8064";
> ++
> ++ memory at 0 {
> ++ reg = <0x42000000 0xe000000>;
> ++ device_type = "memory";
> ++ };
> ++
> ++ reserved-memory {
> ++ #address-cells = <1>;
> ++ #size-cells = <1>;
> ++ ranges;
> ++ rsvd at 41200000 {
> ++ reg = <0x41200000 0x300000>;
> ++ no-map;
> ++ };
> ++ };
> ++
> ++ aliases {
> ++ serial0 = &uart4;
> ++ mdio-gpio0 = &mdio0;
> ++ };
> ++
> ++ chosen {
> ++ bootargs = "rootfstype=squashfs noinitrd";
> ++ linux,stdout-path = "serial0:115200n8";
> ++ };
> ++
> ++ soc {
> ++ pinmux at 800000 {
> ++ i2c4_pins: i2c4_pinmux {
> ++ pins = "gpio12", "gpio13";
> ++ function = "gsbi4";
> ++ bias-disable;
> ++ };
> ++
> ++ pcie0_pins: pcie0_pinmux {
> ++ mux {
> ++ pins = "gpio3";
> ++ function = "pcie1_rst";
> ++ drive-strength = <12>;
> ++ bias-disable;
> ++ };
> ++ };
> ++
> ++ pcie1_pins: pcie1_pinmux {
> ++ mux {
> ++ pins = "gpio48";
> ++ function = "pcie2_rst";
> ++ drive-strength = <12>;
> ++ bias-disable;
> ++ };
> ++ };
> ++
> ++ nand_pins: nand_pins {
> ++ mux {
> ++ pins = "gpio34", "gpio35", "gpio36",
> ++ "gpio37", "gpio38", "gpio39",
> ++ "gpio40", "gpio41", "gpio42",
> ++ "gpio43", "gpio44", "gpio45",
> ++ "gpio46", "gpio47";
> ++ function = "nand";
> ++ drive-strength = <10>;
> ++ bias-disable;
> ++ };
> ++ pullups {
> ++ pins = "gpio39";
> ++ bias-pull-up;
> ++ };
> ++ hold {
> ++ pins = "gpio40", "gpio41", "gpio42",
> ++ "gpio43", "gpio44", "gpio45",
> ++ "gpio46", "gpio47";
> ++ bias-bus-hold;
> ++ };
> ++ };
> ++
> ++ mdio0_pins: mdio0_pins {
> ++ mux {
> ++ pins = "gpio0", "gpio1";
> ++ function = "gpio";
> ++ drive-strength = <8>;
> ++ bias-disable;
> ++ };
> ++ };
> ++
> ++ rgmii2_pins: rgmii2_pins {
> ++ mux {
> ++ pins = "gpio27", "gpio28", "gpio29", "gpio30",
> "gpio31", "gpio32",
> ++ "gpio51", "gpio52", "gpio59", "gpio60",
> "gpio61", "gpio62" ;
> ++ function = "rgmii2";
> ++ drive-strength = <8>;
> ++ bias-disable;
> ++ };
> ++ };
> ++ };
> ++
> ++ gsbi at 16300000 {
> ++ qcom,mode = <GSBI_PROT_I2C_UART>;
> ++ status = "ok";
> ++ serial at 16340000 {
> ++ status = "ok";
> ++ };
> ++ /*
> ++ * The i2c device on gsbi4 should not be enabled.
> ++ * On ipq806x designs gsbi4 i2c is meant for exclusive
> ++ * RPM usage. Turning this on in kernel manifests as
> ++ * i2c failure for the RPM.
> ++ */
> ++ };
> ++
> ++ sata-phy at 1b400000 {
> ++ status = "ok";
> ++ };
> ++
> ++ sata at 29000000 {
> ++ status = "ok";
> ++ };
> ++
> ++ phy at 100f8800 { /* USB3 port 1 HS phy */
> ++ status = "ok";
> ++ };
> ++
> ++ phy at 100f8830 { /* USB3 port 1 SS phy */
> ++ status = "ok";
> ++ };
> ++
> ++ phy at 110f8800 { /* USB3 port 0 HS phy */
> ++ status = "ok";
> ++ };
> ++
> ++ phy at 110f8830 { /* USB3 port 0 SS phy */
> ++ status = "ok";
> ++ };
> ++
> ++ usb30 at 0 {
> ++ status = "ok";
> ++ };
> ++
> ++ usb30 at 1 {
> ++ status = "ok";
> ++ };
> ++
> ++ pcie0: pci at 1b500000 {
> ++ status = "ok";
> ++ reset-gpio = <&qcom_pinmux 3 0>;
> ++ pinctrl-0 = <&pcie0_pins>;
> ++ pinctrl-names = "default";
> ++ };
> ++
> ++ pcie1: pci at 1b700000 {
> ++ status = "ok";
> ++ reset-gpio = <&qcom_pinmux 48 0>;
> ++ pinctrl-0 = <&pcie1_pins>;
> ++ pinctrl-names = "default";
> ++ };
> ++
> ++ nand at 1ac00000 {
> ++ status = "ok";
> ++
> ++ pinctrl-0 = <&nand_pins>;
> ++ pinctrl-names = "default";
> ++
> ++ nand-ecc-strength = <4>;
> ++ nand-bus-width = <8>;
> ++
> ++ #address-cells = <1>;
> ++ #size-cells = <1>;
> ++
> ++ qcadata at 0 {
> ++ label = "qcadata";
> ++ reg = <0x0000000 0x0c80000>;
> ++ read-only;
> ++ };
> ++
> ++ APPSBL at c80000 {
> ++ label = "APPSBL";
> ++ reg = <0x0c80000 0x0500000>;
> ++ read-only;
> ++ };
> ++
> ++ APPSBLENV at 1180000 {
> ++ label = "APPSBLENV";
> ++ reg = <0x1180000 0x0080000>;
> ++ read-only;
> ++ };
> ++
> ++ art: art at 1200000 {
> ++ label = "art";
> ++ reg = <0x1200000 0x0140000>;
> ++ read-only;
> ++ };
> ++
> ++ artbak: art at 1340000 {
> ++ label = "artbak";
> ++ reg = <0x1340000 0x0140000>;
> ++ read-only;
> ++ };
> ++
> ++ kernel at 1480000 {
> ++ label = "kernel";
> ++ reg = <0x1480000 0x0200000>;
> ++ };
> ++
> ++ ubi at 1680000 {
> ++ label = "ubi";
> ++ reg = <0x1680000 0x1E00000>;
> ++ };
> ++
> ++ netgear at 3480000 {
> ++ label = "netgear";
> ++ reg = <0x3480000 0x4480000>;
> ++ read-only;
> ++ };
> ++
> ++ reserve at 7900000 {
> ++ label = "reserve";
> ++ reg = <0x7900000 0x0700000>;
> ++ read-only;
> ++ };
> ++
> ++ firmware at 1480000 {
> ++ label = "firmware";
> ++ reg = <0x1480000 0x2000000>;
> ++ };
> ++
> ++ };
> ++
> ++ mdio0: mdio {
> ++ compatible = "virtual,mdio-gpio";
> ++ #address-cells = <1>;
> ++ #size-cells = <0>;
> ++ gpios = <&qcom_pinmux 1 0 &qcom_pinmux 0 0>;
> ++ pinctrl-0 = <&mdio0_pins>;
> ++ pinctrl-names = "default";
> ++
> ++ phy0: ethernet-phy at 0 {
> ++ device_type = "ethernet-phy";
> ++ reg = <0>;
> ++ qca,ar8327-initvals = <
> ++ 0x00004 0x7600000 /* PAD0_MODE */
> ++ 0x00008 0x1000000 /* PAD5_MODE */
> ++ 0x0000c 0x80 /* PAD6_MODE */
> ++ 0x000e4 0xaa545 /* MAC_POWER_SEL */
> ++ 0x000e0 0xc74164de /* SGMII_CTRL */
> ++ 0x0007c 0x4e /* PORT0_STATUS */
> ++ 0x00094 0x4e /* PORT6_STATUS */
> ++ >;
> ++ };
> ++
> ++ phy4: ethernet-phy at 4 {
> ++ device_type = "ethernet-phy";
> ++ reg = <4>;
> ++ };
> ++ };
> ++
> ++ gmac1: ethernet at 37200000 {
> ++ status = "ok";
> ++ phy-mode = "rgmii";
> ++ phy-handle = <&phy4>;
> ++ qcom,id = <1>;
> ++
> ++ pinctrl-0 = <&rgmii2_pins>;
> ++ pinctrl-names = "default";
> ++
> ++ mtd-mac-address = <&art 6>;
> ++ };
> ++
> ++ gmac2: ethernet at 37400000 {
> ++ status = "ok";
> ++ phy-mode = "sgmii";
> ++ qcom,id = <2>;
> ++
> ++ mtd-mac-address = <&art 0>;
> ++
> ++ fixed-link {
> ++ speed = <1000>;
> ++ full-duplex;
> ++ };
> ++ };
> ++ };
> ++
> ++ gpio-keys {
> ++ compatible = "gpio-keys";
> ++
> ++ wifi {
> ++ label = "wifi";
> ++ gpios = <&qcom_pinmux 6 1>;
> ++ linux,code = <KEY_WLAN>;
> ++ };
> ++
> ++ reset {
> ++ label = "reset";
> ++ gpios = <&qcom_pinmux 54 1>;
> ++ linux,code = <KEY_RESTART>;
> ++ };
> ++
> ++ wps {
> ++ label = "wps";
> ++ gpios = <&qcom_pinmux 65 1>;
> ++ linux,code = <KEY_WPS_BUTTON>;
> ++ };
> ++ };
> ++
> ++ gpio-leds {
> ++ compatible = "gpio-leds";
> ++
> ++ usb1 {
> ++ label = "d7800:amber:usb1";
> ++ gpios = <&qcom_pinmux 7 0>;
> ++ };
> ++
> ++ usb3 {
> ++ label = "d7800:amber:usb3";
> ++ gpios = <&qcom_pinmux 8 0>;
> ++ };
> ++
> ++ status {
> ++ label = "d7800:amber:status";
> ++ gpios = <&qcom_pinmux 9 0>;
> ++ };
> ++
> ++ internet {
> ++ label = "d7800:white:internet";
> ++ gpios = <&qcom_pinmux 22 0>;
> ++ };
> ++
> ++ wan {
> ++ label = "d7800:white:wan";
> ++ gpios = <&qcom_pinmux 23 0>;
> ++ };
> ++
> ++ wps {
> ++ label = "d7800:white:wps";
> ++ gpios = <&qcom_pinmux 24 0>;
> ++ };
> ++
> ++ esata {
> ++ label = "d7800:white:esata";
> ++ gpios = <&qcom_pinmux 26 0>;
> ++ };
> ++
> ++ power {
> ++ label = "d7800:white:power";
> ++ gpios = <&qcom_pinmux 53 0>;
> ++ default-state = "on";
> ++ };
> ++
> ++ rfkill {
> ++ label = "d7800:white:rfkill";
> ++ gpios = <&qcom_pinmux 64 0>;
> ++ };
> ++
> ++ wifi5g {
> ++ label = "d7800:white:wifi5g";
> ++ gpios = <&qcom_pinmux 67 0>;
> ++ };
> ++ };
> ++};
> ++
> ++&adm_dma {
> ++ status = "ok";
> ++};
> diff --git a/target/linux/ipq806x/profiles/netgear.mk
> b/target/linux/ipq806x/profiles/netgear.mk
> index 3402f45..e1e7ed2 100644
> --- a/target/linux/ipq806x/profiles/netgear.mk
> +++ b/target/linux/ipq806x/profiles/netgear.mk
> @@ -17,4 +17,18 @@ endef
> define Profile/R7500/Description
> Package set for the Netgear Nighthawk X4 R7500.
> endef
> +
> +define Profile/D7800
> + NAME:=Netgear Nighthawk X4 D7800
> + PACKAGES:= \
> + kmod-usb-core kmod-usb-ohci kmod-usb2 kmod-ledtrig-usbdev \
> + kmod-usb3 kmod-usb-dwc3-qcom kmod-usb-phy-qcom-dwc3 \
> + kmod-ath10k wpad-mini ath10k-firmware-qca99x0
> +endef
> +
> +define Profile/D7800/Description
> + Package set for the Netgear Nighthawk X4 D7800.
> +endef
> +
> $(eval $(call Profile,R7500))
> +$(eval $(call Profile,D7800))
_______________________________________________
openwrt-devel mailing list
openwrt-devel at lists.openwrt.org
https://lists.openwrt.org/cgi-bin/mailman/listinfo/openwrt-devel
More information about the openwrt-devel
mailing list