[OpenWrt-Devel] [PATCH 02/10] imx6: Add 4.3 support
Pushpal Sidhu
psidhu at gateworks.com
Mon Dec 21 17:25:12 EST 2015
Build and boot tested on the following hardware:
* GW54xx
* GW53xx
* GW52xx
* GW51xx
* GW552x
* GW551x
Signed-off-by: Pushpal Sidhu <psidhu at gateworks.com>
---
target/linux/imx6/config-4.3 | 410 ++++++++
.../linux/imx6/files-4.3/drivers/net/phy/gw16083.c | 1046 ++++++++++++++++++++
.../linux/imx6/files-4.3/drivers/net/phy/gw16083.h | 123 +++
...-ventana-set-GW54xx-PMIC-swbst-regulator-.patch | 28 +
...mx-ventana-fix-GW53xx-GW54xx-lvds-channel.patch | 37 +
...mx-ventana-fix-GW53xx-GW54xx-lvds-channel.patch | 76 ++
target/linux/imx6/patches-4.3/100-bootargs.patch | 13 +
...-add-i210-i211-support-for-phy-read-write.patch | 131 +++
...-phy-read-write-functions-that-accept-phy.patch | 266 +++++
...egister-mii_bus-for-SerDes-w-external-phy.patch | 314 ++++++
...ver-for-GW16083-Ethernet-Expansion-Mezzan.patch | 31 +
...-imx-ventana-added-GW16083-to-device-tree.patch | 64 ++
12 files changed, 2539 insertions(+)
create mode 100644 target/linux/imx6/config-4.3
create mode 100644 target/linux/imx6/files-4.3/drivers/net/phy/gw16083.c
create mode 100644 target/linux/imx6/files-4.3/drivers/net/phy/gw16083.h
create mode 100644 target/linux/imx6/patches-4.3/035-ARM-dts-imx-ventana-set-GW54xx-PMIC-swbst-regulator-.patch
create mode 100644 target/linux/imx6/patches-4.3/036-ARM-dts-imx-ventana-fix-GW53xx-GW54xx-lvds-channel.patch
create mode 100644 target/linux/imx6/patches-4.3/037-ARM-dts-imx-ventana-fix-GW53xx-GW54xx-lvds-channel.patch
create mode 100644 target/linux/imx6/patches-4.3/100-bootargs.patch
create mode 100644 target/linux/imx6/patches-4.3/202-net-igb-add-i210-i211-support-for-phy-read-write.patch
create mode 100644 target/linux/imx6/patches-4.3/203-net-igb-add-phy-read-write-functions-that-accept-phy.patch
create mode 100644 target/linux/imx6/patches-4.3/204-net-igb-register-mii_bus-for-SerDes-w-external-phy.patch
create mode 100644 target/linux/imx6/patches-4.3/205-phy-add-driver-for-GW16083-Ethernet-Expansion-Mezzan.patch
create mode 100644 target/linux/imx6/patches-4.3/206-ARM-imx-ventana-added-GW16083-to-device-tree.patch
diff --git a/target/linux/imx6/config-4.3 b/target/linux/imx6/config-4.3
new file mode 100644
index 0000000..ae4f797
--- /dev/null
+++ b/target/linux/imx6/config-4.3
@@ -0,0 +1,410 @@
+CONFIG_AHCI_IMX=y
+CONFIG_ALIGNMENT_TRAP=y
+CONFIG_ARCH_HAS_ATOMIC64_DEC_IF_POSITIVE=y
+CONFIG_ARCH_HAS_ELF_RANDOMIZE=y
+CONFIG_ARCH_HAS_GCOV_PROFILE_ALL=y
+CONFIG_ARCH_HAS_RESET_CONTROLLER=y
+CONFIG_ARCH_HAS_SG_CHAIN=y
+CONFIG_ARCH_HAS_TICK_BROADCAST=y
+CONFIG_ARCH_HAVE_CUSTOM_GPIO_H=y
+CONFIG_ARCH_HIBERNATION_POSSIBLE=y
+CONFIG_ARCH_MIGHT_HAVE_PC_PARPORT=y
+CONFIG_ARCH_MULTIPLATFORM=y
+# CONFIG_ARCH_MULTI_CPU_AUTO is not set
+CONFIG_ARCH_MULTI_V6_V7=y
+CONFIG_ARCH_MULTI_V7=y
+CONFIG_ARCH_MXC=y
+CONFIG_ARCH_NR_GPIO=0
+CONFIG_ARCH_REQUIRE_GPIOLIB=y
+# CONFIG_ARCH_SELECT_MEMORY_MODEL is not set
+# CONFIG_ARCH_SPARSEMEM_DEFAULT is not set
+CONFIG_ARCH_SUPPORTS_ATOMIC_RMW=y
+CONFIG_ARCH_SUPPORTS_UPROBES=y
+CONFIG_ARCH_SUSPEND_POSSIBLE=y
+CONFIG_ARCH_USE_BUILTIN_BSWAP=y
+CONFIG_ARCH_USE_CMPXCHG_LOCKREF=y
+CONFIG_ARCH_WANT_GENERAL_HUGETLB=y
+CONFIG_ARCH_WANT_IPC_PARSE_VERSION=y
+CONFIG_ARCH_WANT_OPTIONAL_GPIOLIB=y
+CONFIG_ARM=y
+# CONFIG_ARM_BIG_LITTLE_CPUFREQ is not set
+# CONFIG_ARM_CCI500_PMU is not set
+# CONFIG_ARM_CPU_SUSPEND is not set
+CONFIG_ARM_ERRATA_754322=y
+CONFIG_ARM_ERRATA_764369=y
+CONFIG_ARM_ERRATA_775420=y
+CONFIG_ARM_GIC=y
+CONFIG_ARM_HAS_SG_CHAIN=y
+CONFIG_ARM_HEAVY_MB=y
+CONFIG_ARM_IMX6Q_CPUFREQ=y
+CONFIG_ARM_L1_CACHE_SHIFT=6
+CONFIG_ARM_L1_CACHE_SHIFT_6=y
+# CONFIG_ARM_LPAE is not set
+CONFIG_ARM_PATCH_PHYS_VIRT=y
+CONFIG_ARM_PMU=y
+CONFIG_ARM_THUMB=y
+# CONFIG_ARM_THUMBEE is not set
+CONFIG_ARM_VIRT_EXT=y
+CONFIG_ATA=y
+CONFIG_ATAGS=y
+# CONFIG_ATA_SFF is not set
+CONFIG_AUTO_ZRELADDR=y
+CONFIG_CACHE_L2X0=y
+CONFIG_CC_OPTIMIZE_FOR_SIZE=y
+CONFIG_CLKDEV_LOOKUP=y
+CONFIG_CLKSRC_IMX_GPT=y
+CONFIG_CLKSRC_MMIO=y
+CONFIG_CLKSRC_OF=y
+CONFIG_CLONE_BACKWARDS=y
+CONFIG_COMMON_CLK=y
+CONFIG_CPUFREQ_DT=y
+CONFIG_CPU_32v6K=y
+CONFIG_CPU_32v7=y
+CONFIG_CPU_ABRT_EV7=y
+# CONFIG_CPU_BPREDICT_DISABLE is not set
+CONFIG_CPU_CACHE_V7=y
+CONFIG_CPU_CACHE_VIPT=y
+CONFIG_CPU_COPY_V6=y
+CONFIG_CPU_CP15=y
+CONFIG_CPU_CP15_MMU=y
+CONFIG_CPU_FREQ=y
+# CONFIG_CPU_FREQ_DEFAULT_GOV_CONSERVATIVE is not set
+# CONFIG_CPU_FREQ_DEFAULT_GOV_ONDEMAND is not set
+CONFIG_CPU_FREQ_DEFAULT_GOV_PERFORMANCE=y
+# CONFIG_CPU_FREQ_DEFAULT_GOV_POWERSAVE is not set
+# CONFIG_CPU_FREQ_DEFAULT_GOV_USERSPACE is not set
+CONFIG_CPU_FREQ_GOV_COMMON=y
+CONFIG_CPU_FREQ_GOV_CONSERVATIVE=y
+CONFIG_CPU_FREQ_GOV_ONDEMAND=y
+CONFIG_CPU_FREQ_GOV_PERFORMANCE=y
+CONFIG_CPU_FREQ_GOV_POWERSAVE=y
+CONFIG_CPU_FREQ_GOV_USERSPACE=y
+CONFIG_CPU_FREQ_STAT=y
+CONFIG_CPU_FREQ_STAT_DETAILS=y
+CONFIG_CPU_HAS_ASID=y
+# CONFIG_CPU_ICACHE_DISABLE is not set
+CONFIG_CPU_PABRT_V7=y
+CONFIG_CPU_RMAP=y
+CONFIG_CPU_THERMAL=y
+CONFIG_CPU_TLB_V7=y
+CONFIG_CPU_V7=y
+CONFIG_CRC16=y
+CONFIG_CRYPTO_CRC32C=y
+CONFIG_CRYPTO_DEFLATE=y
+CONFIG_CRYPTO_HASH=y
+CONFIG_CRYPTO_HASH2=y
+CONFIG_CRYPTO_LZO=y
+CONFIG_CRYPTO_RNG2=y
+CONFIG_CRYPTO_WORKQUEUE=y
+CONFIG_CRYPTO_XZ=y
+CONFIG_DCACHE_WORD_ACCESS=y
+CONFIG_DEBUG_IMX_UART_PORT=1
+CONFIG_DEBUG_LL_INCLUDE="mach/debug-macro.S"
+# CONFIG_DEBUG_UART_8250 is not set
+# CONFIG_DEBUG_USER is not set
+CONFIG_DECOMPRESS_BZIP2=y
+CONFIG_DECOMPRESS_GZIP=y
+CONFIG_DECOMPRESS_LZO=y
+CONFIG_DECOMPRESS_XZ=y
+CONFIG_DMADEVICES=y
+CONFIG_DMA_ENGINE=y
+CONFIG_DMA_OF=y
+CONFIG_DTC=y
+# CONFIG_DW_DMAC_PCI is not set
+CONFIG_EDAC_ATOMIC_SCRUB=y
+CONFIG_EDAC_SUPPORT=y
+CONFIG_EXT2_FS=y
+CONFIG_EXT2_FS_POSIX_ACL=y
+CONFIG_EXT2_FS_SECURITY=y
+CONFIG_EXT2_FS_XATTR=y
+CONFIG_EXT3_FS=y
+CONFIG_EXT3_FS_POSIX_ACL=y
+CONFIG_EXT3_FS_SECURITY=y
+CONFIG_EXT4_FS=y
+CONFIG_EXT4_FS_POSIX_ACL=y
+CONFIG_EXT4_FS_SECURITY=y
+CONFIG_FEC=y
+CONFIG_FIX_EARLYCON_MEM=y
+CONFIG_FRAME_POINTER=y
+# CONFIG_FSL_PQ_MDIO is not set
+CONFIG_FS_MBCACHE=y
+CONFIG_FS_POSIX_ACL=y
+CONFIG_GENERIC_ALLOCATOR=y
+CONFIG_GENERIC_BUG=y
+CONFIG_GENERIC_CLOCKEVENTS=y
+CONFIG_GENERIC_CLOCKEVENTS_BROADCAST=y
+CONFIG_GENERIC_IDLE_POLL_SETUP=y
+CONFIG_GENERIC_IO=y
+CONFIG_GENERIC_IRQ_CHIP=y
+CONFIG_GENERIC_IRQ_SHOW=y
+CONFIG_GENERIC_IRQ_SHOW_LEVEL=y
+CONFIG_GENERIC_PCI_IOMAP=y
+CONFIG_GENERIC_SCHED_CLOCK=y
+CONFIG_GENERIC_SMP_IDLE_THREAD=y
+CONFIG_GENERIC_STRNCPY_FROM_USER=y
+CONFIG_GENERIC_STRNLEN_USER=y
+# CONFIG_GIANFAR is not set
+CONFIG_GLOB=y
+CONFIG_GPIOLIB=y
+CONFIG_GPIO_DEVRES=y
+CONFIG_GPIO_GENERIC=y
+CONFIG_GPIO_MXC=y
+CONFIG_GPIO_SYSFS=y
+CONFIG_HANDLE_DOMAIN_IRQ=y
+CONFIG_HARDIRQS_SW_RESEND=y
+CONFIG_HAS_DMA=y
+CONFIG_HAS_IOMEM=y
+CONFIG_HAS_IOPORT_MAP=y
+# CONFIG_HAVE_64BIT_ALIGNED_ACCESS is not set
+CONFIG_HAVE_ARCH_AUDITSYSCALL=y
+CONFIG_HAVE_ARCH_BITREVERSE=y
+CONFIG_HAVE_ARCH_JUMP_LABEL=y
+CONFIG_HAVE_ARCH_KGDB=y
+CONFIG_HAVE_ARCH_PFN_VALID=y
+CONFIG_HAVE_ARCH_SECCOMP_FILTER=y
+CONFIG_HAVE_ARCH_TRACEHOOK=y
+CONFIG_HAVE_ARM_SCU=y
+CONFIG_HAVE_ARM_TWD=y
+# CONFIG_HAVE_BOOTMEM_INFO_NODE is not set
+CONFIG_HAVE_BPF_JIT=y
+CONFIG_HAVE_CC_STACKPROTECTOR=y
+CONFIG_HAVE_CLK=y
+CONFIG_HAVE_CLK_PREPARE=y
+CONFIG_HAVE_CONTEXT_TRACKING=y
+CONFIG_HAVE_C_RECORDMCOUNT=y
+CONFIG_HAVE_DEBUG_KMEMLEAK=y
+CONFIG_HAVE_DMA_API_DEBUG=y
+CONFIG_HAVE_DMA_ATTRS=y
+CONFIG_HAVE_DMA_CONTIGUOUS=y
+CONFIG_HAVE_DYNAMIC_FTRACE=y
+CONFIG_HAVE_EFFICIENT_UNALIGNED_ACCESS=y
+CONFIG_HAVE_FTRACE_MCOUNT_RECORD=y
+CONFIG_HAVE_FUNCTION_GRAPH_TRACER=y
+CONFIG_HAVE_FUNCTION_TRACER=y
+CONFIG_HAVE_GENERIC_DMA_COHERENT=y
+CONFIG_HAVE_HW_BREAKPOINT=y
+CONFIG_HAVE_IDE=y
+CONFIG_HAVE_IMX_ANATOP=y
+CONFIG_HAVE_IMX_GPC=y
+CONFIG_HAVE_IMX_MMDC=y
+CONFIG_HAVE_IMX_SRC=y
+CONFIG_HAVE_IRQ_TIME_ACCOUNTING=y
+CONFIG_HAVE_KERNEL_GZIP=y
+CONFIG_HAVE_KERNEL_LZ4=y
+CONFIG_HAVE_KERNEL_LZMA=y
+CONFIG_HAVE_KERNEL_LZO=y
+CONFIG_HAVE_KERNEL_XZ=y
+CONFIG_HAVE_MEMBLOCK=y
+CONFIG_HAVE_MOD_ARCH_SPECIFIC=y
+CONFIG_HAVE_NET_DSA=y
+CONFIG_HAVE_OPROFILE=y
+CONFIG_HAVE_OPTPROBES=y
+CONFIG_HAVE_PERF_EVENTS=y
+CONFIG_HAVE_PERF_REGS=y
+CONFIG_HAVE_PERF_USER_STACK_DUMP=y
+CONFIG_HAVE_PROC_CPU=y
+CONFIG_HAVE_REGS_AND_STACK_ACCESS_API=y
+CONFIG_HAVE_SMP=y
+CONFIG_HAVE_SYSCALL_TRACEPOINTS=y
+CONFIG_HAVE_UID16=y
+CONFIG_HAVE_VIRT_CPU_ACCOUNTING_GEN=y
+# CONFIG_HSU_DMA_PCI is not set
+CONFIG_HZ_FIXED=0
+CONFIG_I2C=y
+CONFIG_I2C_BOARDINFO=y
+CONFIG_I2C_CHARDEV=y
+CONFIG_I2C_IMX=y
+CONFIG_IMX2_WDT=y
+CONFIG_IMX_DMA=y
+CONFIG_IMX_SDMA=y
+CONFIG_IMX_THERMAL=y
+# CONFIG_IMX_WEIM is not set
+CONFIG_INITRAMFS_SOURCE=""
+CONFIG_IOMMU_HELPER=y
+CONFIG_IRQCHIP=y
+CONFIG_IRQ_DOMAIN=y
+CONFIG_IRQ_DOMAIN_HIERARCHY=y
+CONFIG_IRQ_FORCED_THREADING=y
+CONFIG_IRQ_WORK=y
+CONFIG_JBD2=y
+CONFIG_LIBFDT=y
+CONFIG_LOCK_SPIN_ON_OWNER=y
+CONFIG_LZO_COMPRESS=y
+CONFIG_LZO_DECOMPRESS=y
+CONFIG_MDIO_BOARDINFO=y
+CONFIG_MFD_SYSCON=y
+CONFIG_MIGHT_HAVE_CACHE_L2X0=y
+CONFIG_MIGHT_HAVE_PCI=y
+CONFIG_MMC=y
+CONFIG_MMC_BLOCK=y
+# CONFIG_MMC_MXC is not set
+CONFIG_MMC_SDHCI=y
+CONFIG_MMC_SDHCI_ESDHC_IMX=y
+CONFIG_MMC_SDHCI_IO_ACCESSORS=y
+# CONFIG_MMC_SDHCI_PCI is not set
+CONFIG_MMC_SDHCI_PLTFM=y
+# CONFIG_MMC_TIFM_SD is not set
+CONFIG_MODULES_TREE_LOOKUP=y
+CONFIG_MODULES_USE_ELF_REL=y
+CONFIG_MTD_NAND=y
+CONFIG_MTD_NAND_ECC=y
+CONFIG_MTD_NAND_GPMI_NAND=y
+# CONFIG_MTD_PHYSMAP_OF is not set
+CONFIG_MTD_UBI=y
+CONFIG_MTD_UBI_BEB_LIMIT=20
+CONFIG_MTD_UBI_BLOCK=y
+# CONFIG_MTD_UBI_FASTMAP is not set
+# CONFIG_MTD_UBI_GLUEBI is not set
+CONFIG_MTD_UBI_WL_THRESHOLD=4096
+CONFIG_MULTI_IRQ_HANDLER=y
+CONFIG_MUTEX_SPIN_ON_OWNER=y
+# CONFIG_MX3_IPU is not set
+CONFIG_MXS_DMA=y
+CONFIG_NEED_DMA_MAP_STATE=y
+CONFIG_NEON=y
+CONFIG_NET_FLOW_LIMIT=y
+CONFIG_NET_PTP_CLASSIFY=y
+CONFIG_NLS=y
+CONFIG_NLS_CODEPAGE_437=y
+CONFIG_NO_BOOTMEM=y
+CONFIG_NO_HZ_COMMON=y
+CONFIG_NO_HZ_IDLE=y
+CONFIG_NR_CPUS=4
+CONFIG_OF=y
+CONFIG_OF_ADDRESS=y
+CONFIG_OF_ADDRESS_PCI=y
+CONFIG_OF_EARLY_FLATTREE=y
+CONFIG_OF_FLATTREE=y
+CONFIG_OF_GPIO=y
+CONFIG_OF_IRQ=y
+CONFIG_OF_MDIO=y
+CONFIG_OF_MTD=y
+CONFIG_OF_NET=y
+CONFIG_OF_PCI=y
+CONFIG_OF_PCI_IRQ=y
+CONFIG_OF_RESERVED_MEM=y
+CONFIG_OLD_SIGACTION=y
+CONFIG_OLD_SIGSUSPEND3=y
+CONFIG_OUTER_CACHE=y
+CONFIG_OUTER_CACHE_SYNC=y
+CONFIG_PAGEFLAGS_EXTENDED=y
+CONFIG_PAGE_OFFSET=0x80000000
+CONFIG_PCI=y
+CONFIG_PCIEAER=y
+CONFIG_PCIEPORTBUS=y
+CONFIG_PCIE_DW=y
+CONFIG_PCI_DOMAINS=y
+CONFIG_PCI_DOMAINS_GENERIC=y
+CONFIG_PCI_IMX6=y
+CONFIG_PERF_EVENTS=y
+CONFIG_PERF_USE_VMALLOC=y
+CONFIG_PGTABLE_LEVELS=2
+CONFIG_PHYLIB=y
+CONFIG_PINCTRL=y
+CONFIG_PINCTRL_IMX=y
+CONFIG_PINCTRL_IMX6Q=y
+CONFIG_PINCTRL_IMX6SL=y
+CONFIG_PINCTRL_IMX6SX=y
+CONFIG_PINCTRL_IMX6UL=y
+# CONFIG_PINCTRL_SINGLE is not set
+CONFIG_PL310_ERRATA_588369=y
+CONFIG_PL310_ERRATA_727915=y
+# CONFIG_PL310_ERRATA_753970 is not set
+CONFIG_PL310_ERRATA_769419=y
+CONFIG_PM_OPP=y
+CONFIG_PPS=y
+CONFIG_PTP_1588_CLOCK=y
+CONFIG_RAS=y
+CONFIG_RATIONAL=y
+CONFIG_RCU_STALL_COMMON=y
+CONFIG_RD_BZIP2=y
+CONFIG_RD_GZIP=y
+CONFIG_RD_LZO=y
+CONFIG_RD_XZ=y
+CONFIG_REGMAP=y
+CONFIG_REGMAP_I2C=y
+CONFIG_REGMAP_MMIO=y
+CONFIG_REGMAP_SPI=y
+CONFIG_REGULATOR=y
+CONFIG_REGULATOR_ANATOP=y
+CONFIG_REGULATOR_FIXED_VOLTAGE=y
+CONFIG_REGULATOR_PFUZE100=y
+CONFIG_RFS_ACCEL=y
+CONFIG_RPS=y
+CONFIG_RTC_CLASS=y
+# CONFIG_RTC_DRV_IMXDI is not set
+# CONFIG_RTC_DRV_MXC is not set
+CONFIG_RWSEM_SPIN_ON_OWNER=y
+CONFIG_RWSEM_XCHGADD_ALGORITHM=y
+CONFIG_SATA_AHCI_PLATFORM=y
+CONFIG_SCHED_HRTICK=y
+# CONFIG_SCHED_INFO is not set
+CONFIG_SCSI=y
+CONFIG_SERIAL_IMX=y
+CONFIG_SERIAL_IMX_CONSOLE=y
+# CONFIG_SG_SPLIT is not set
+CONFIG_SMP=y
+CONFIG_SMP_ON_UP=y
+CONFIG_SOC_BUS=y
+# CONFIG_SOC_IMX50 is not set
+# CONFIG_SOC_IMX51 is not set
+# CONFIG_SOC_IMX53 is not set
+CONFIG_SOC_IMX6=y
+CONFIG_SOC_IMX6Q=y
+CONFIG_SOC_IMX6SL=y
+CONFIG_SOC_IMX6SX=y
+CONFIG_SOC_IMX6UL=y
+# CONFIG_SOC_IMX7D is not set
+# CONFIG_SOC_LS1021A is not set
+# CONFIG_SOC_VF610 is not set
+CONFIG_SPARSE_IRQ=y
+CONFIG_SPI=y
+CONFIG_SPI_BITBANG=y
+CONFIG_SPI_IMX=y
+CONFIG_SPI_MASTER=y
+CONFIG_SRAM=y
+CONFIG_SRCU=y
+CONFIG_STMP_DEVICE=y
+CONFIG_STOP_MACHINE=y
+# CONFIG_SUNXI_SRAM is not set
+CONFIG_SWIOTLB=y
+CONFIG_SWP_EMULATE=y
+CONFIG_SYS_SUPPORTS_APM_EMULATION=y
+CONFIG_THERMAL=y
+# CONFIG_THERMAL_DEFAULT_GOV_FAIR_SHARE is not set
+# CONFIG_THERMAL_DEFAULT_GOV_POWER_ALLOCATOR is not set
+CONFIG_THERMAL_DEFAULT_GOV_STEP_WISE=y
+# CONFIG_THERMAL_DEFAULT_GOV_USER_SPACE is not set
+# CONFIG_THERMAL_EMULATION is not set
+# CONFIG_THERMAL_GOV_FAIR_SHARE is not set
+# CONFIG_THERMAL_GOV_POWER_ALLOCATOR is not set
+CONFIG_THERMAL_GOV_STEP_WISE=y
+# CONFIG_THERMAL_GOV_USER_SPACE is not set
+CONFIG_THERMAL_OF=y
+CONFIG_THERMAL_WRITABLE_TRIPS=y
+# CONFIG_THUMB2_KERNEL is not set
+CONFIG_TICK_CPU_ACCOUNTING=y
+CONFIG_TREE_RCU=y
+CONFIG_UBIFS_FS=y
+CONFIG_UBIFS_FS_ADVANCED_COMPR=y
+CONFIG_UBIFS_FS_LZO=y
+CONFIG_UBIFS_FS_XZ=y
+CONFIG_UBIFS_FS_ZLIB=y
+CONFIG_UNCOMPRESS_INCLUDE="debug/uncompress.h"
+# CONFIG_USB_MXS_PHY is not set
+CONFIG_USB_SUPPORT=y
+CONFIG_USE_OF=y
+CONFIG_VECTORS_BASE=0xffff0000
+CONFIG_VFP=y
+CONFIG_VFPv3=y
+CONFIG_VMSPLIT_2G=y
+# CONFIG_VMSPLIT_3G is not set
+CONFIG_WATCHDOG_CORE=y
+CONFIG_XPS=y
+CONFIG_XZ_DEC_ARM=y
+CONFIG_XZ_DEC_BCJ=y
+CONFIG_ZBOOT_ROM_BSS=0x0
+CONFIG_ZBOOT_ROM_TEXT=0x0
+CONFIG_ZLIB_DEFLATE=y
+CONFIG_ZLIB_INFLATE=y
+CONFIG_ZONE_DMA_FLAG=0
diff --git a/target/linux/imx6/files-4.3/drivers/net/phy/gw16083.c b/target/linux/imx6/files-4.3/drivers/net/phy/gw16083.c
new file mode 100644
index 0000000..bdc7446
--- /dev/null
+++ b/target/linux/imx6/files-4.3/drivers/net/phy/gw16083.c
@@ -0,0 +1,1046 @@
+/*
+ * drivers/net/phy/gw16083.c
+ *
+ * Driver for GW16083 Ventana Ethernet Expansion Mezzanine
+ *
+ * Author: Tim Harvey
+ *
+ * Copyright (c) 2014 Tim Harvey <tharvey at gateworks.com>
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License as published by the
+ * Free Software Foundation; either version 2 of the License, or (at your
+ * option) any later version.
+ *
+ */
+
+/*
+ * The GW16083 interfaces with a Ventana baseboard via the PCIe bus, an i2c
+ * bus (i2c2), and a couple of GPIO's. On the PCIe bus is an i210 GigE with
+ * its MAC connected to Port4 of a Marvell MV88E6176 7-port GigE switch via
+ * MDIO and RGMII. Ports 0-3 are standard copper RJ45 but Ports 5 and 6
+ * connect to Marvell MV88E1111 dual-mode Copper/Fiber PHY's over SGMII and
+ * MDIO. The PHY's have both an RG45 for copper and an SFP module.
+ */
+
+#include <linux/kernel.h>
+#include <linux/string.h>
+#include <linux/errno.h>
+#include <linux/unistd.h>
+#include <linux/i2c.h>
+#include <linux/interrupt.h>
+#include <linux/init.h>
+#include <linux/delay.h>
+#include <linux/device.h>
+#include <linux/netdevice.h>
+#include <linux/etherdevice.h>
+#include <linux/skbuff.h>
+#include <linux/spinlock.h>
+#include <linux/mm.h>
+#include <linux/module.h>
+#include <linux/mii.h>
+#include <linux/ethtool.h>
+#include <linux/phy.h>
+#include <linux/marvell_phy.h>
+#include <linux/of_platform.h>
+#include <linux/platform_device.h>
+
+#include <linux/io.h>
+#include <asm/irq.h>
+#include <net/dsa.h>
+#include <linux/uaccess.h>
+
+#include "gw16083.h"
+
+#undef FAIL_ON_CHECKSUM_ERR /* fail to configure SFP if checksum bad */
+#define PORT_POWER_CONTROL /* ports can be enabled/disabled via sysfs */
+#define PORT_MODE_CONTROL /* ports 5/6 can have SFP/RJ45 mode forced */
+#define RGMII_DELAY_ON_PHY /* implement Port5/6 tx/rx delay on PHY vs sw */
+
+MODULE_DESCRIPTION("GW16083 driver");
+MODULE_AUTHOR("Tim Harvey");
+MODULE_LICENSE("GPL");
+
+struct mv88e1111_port_state {
+ int port;
+ bool present;
+ bool serdes;
+ bool sfp_signal;
+ bool sfp_present;
+ bool sfp_compat;
+ bool sfp_enabled;
+ char sfp_id[64];
+};
+
+struct mv88e1111_priv {
+ struct phy_device *phydev;
+ struct i2c_client *client;
+ struct mv88e1111_port_state port5;
+ struct mv88e1111_port_state port6;
+ struct kobject *sysfs_kobj;
+ struct delayed_work work;
+ struct workqueue_struct *workq;
+};
+
+enum {
+ mode_copper = 0,
+ mode_serdes = 1,
+};
+
+#if IS_ENABLED(CONFIG_NET_DSA_MV88E6352)
+static struct dsa_chip_data switch_chip_data = {
+ .port_names = {
+ "lan4",
+ "lan3",
+ "lan2",
+ "lan1",
+ "cpu",
+ "lan5",
+ "lan6",
+ },
+};
+
+static struct dsa_platform_data switch_plat_data = {
+ .nr_chips = 1,
+ .chip = &switch_chip_data,
+};
+
+static struct platform_device switch_device = {
+ .name = "dsa",
+ .id = 0,
+ .num_resources = 0,
+ .dev.platform_data = &switch_plat_data,
+};
+#endif
+
+static struct i2c_client *gw16083_client = NULL;
+
+static int gw16083_read_port_sfp(struct i2c_client *client,
+ struct mv88e1111_port_state *state);
+
+/* read switch port register from port0-6 */
+u16 read_switch_port(struct phy_device *pdev, int port, u8 regaddr)
+{
+ return pdev->bus->read(pdev->bus, MV_BASE + port, regaddr);
+}
+
+/* write switch port register to port0-6 */
+int write_switch_port(struct phy_device *pdev, int port, u8 regaddr, u16 val)
+{
+ return pdev->bus->write(pdev->bus, MV_BASE + port, regaddr, val);
+}
+
+/*
+ * read_switch_port_phy - write a register for a specific port on 88E6176
+ * The 88E6176 PHY registers must be accessed thorugh the Global2 address
+ * using the SMI_PHY_COMMAND_REG and SMI_PHY_DATA_REG.
+ */
+int read_switch_port_phy(struct phy_device *pdev, int port, u8 regaddr)
+{
+ struct mv88e1111_priv *priv = dev_get_drvdata(&pdev->dev);
+ u16 reg;
+ int i;
+
+ dev_dbg(&priv->client->dev, "read_phy: port%d reg=0x%02x\n", port,
+ regaddr);
+ reg = SMIBUSY | SMIMODE22 | SMIOP_READ;
+ reg |= port << DEVADDR;
+ reg |= regaddr << REGADDR;
+ pdev->bus->write(pdev->bus, MV_GLOBAL2, MV_SMI_PHY_COMMAND, reg);
+ for (i = 0; i < 10; i++) {
+ reg = pdev->bus->read(pdev->bus, MV_GLOBAL2,
+ MV_SMI_PHY_COMMAND);
+ if (!(reg & (1<<15)))
+ break;
+ mdelay(1);
+ }
+ /* timeout */
+ if (i == 10)
+ return 0xffff;
+ reg = pdev->bus->read(pdev->bus, MV_GLOBAL2, MV_SMI_PHY_DATA);
+ return reg;
+}
+
+/*
+ * write_switch_port_phy - write a register for a specific port on 88E6176
+ * The 88E6176 PHY registers must be accessed thorugh the Global2 address
+ * using the SMI_PHY_COMMAND_REG and SMI_PHY_DATA_REG.
+ */
+int write_switch_port_phy(struct phy_device *pdev, int port, u8 addr, u16 reg)
+{
+ struct mv88e1111_priv *priv = dev_get_drvdata(&pdev->dev);
+ int i;
+
+ dev_dbg(&priv->client->dev, "write_phy: port%d reg=0x%02x val=0x%04x\n",
+ port, addr, reg);
+ pdev->bus->write(pdev->bus, MV_GLOBAL2, MV_SMI_PHY_DATA, reg);
+ reg = SMIBUSY | SMIMODE22 | SMIOP_WRITE;
+ reg |= port << DEVADDR;
+ reg |= addr << REGADDR;
+ pdev->bus->write(pdev->bus, MV_GLOBAL2, MV_SMI_PHY_COMMAND, reg);
+ for (i = 0; i < 10; i++) {
+ reg = pdev->bus->read(pdev->bus, MV_GLOBAL2,
+ MV_SMI_PHY_COMMAND);
+ if (!(reg & (1<<15)))
+ break;
+ mdelay(1);
+ }
+ /* timeout */
+ if (i == 10)
+ return -ETIMEDOUT;
+
+ return 0;
+}
+
+/* read a scratch register from switch */
+inline u8 read_switch_scratch(struct phy_device *pdev, u8 reg)
+{
+ pdev->bus->write(pdev->bus, MV_GLOBAL2, MV_SCRATCH_MISC, (reg << 8));
+ return pdev->bus->read(pdev->bus, MV_GLOBAL2, MV_SCRATCH_MISC) & 0xff;
+}
+
+/* write a scratch register to switch */
+inline void write_switch_scratch(struct phy_device *pdev, u8 reg, u8 val)
+{
+ pdev->bus->write(pdev->bus, MV_GLOBAL2, MV_SCRATCH_MISC,
+ (1 << 15) | (reg << 8) | val);
+}
+
+/* enable or disable an SFP's TXEN signal */
+static int enable_sfp_txen(struct phy_device *pdev, int port, bool enable)
+{
+ struct mv88e1111_priv *priv = dev_get_drvdata(&pdev->dev);
+ u8 gpio;
+ int bit;
+
+ if (port != 5 && port != 6)
+ return -EINVAL;
+
+ /* GPIO[2:1] output low to enable TXEN */
+ bit = (port == 5) ? 1 : 2;
+ gpio = read_switch_scratch(pdev, MV_GPIO_DATA);
+ if (enable)
+ gpio |= (1 << bit);
+ else
+ gpio &= (1 << bit);
+ write_switch_scratch(pdev, MV_GPIO_DATA, gpio);
+ dev_info(&priv->client->dev, "Port%d: SFP TX %s\n", port, enable ?
+ "enabled" : "disabled");
+ return 0;
+}
+
+/* configure mv88e1111 port for copper or serdes
+ * For Copper we set auto link/duplex/speed detection
+ * For SerDes/Fiber we force 1000mbps link up and auto-neg duplex
+ */
+static int config_mv88e1111_port_sfp(struct phy_device *pdev, int port,
+ bool sfp)
+{
+ struct mv88e1111_priv *priv = dev_get_drvdata(&pdev->dev);
+ u16 reg;
+
+ if (port != 5 && port != 6)
+ return -EINVAL;
+
+ dev_dbg(&priv->client->dev, "%s: Port%d %s\n", __func__, port,
+ sfp ? "SFP" : "copper");
+ if (sfp) {
+ enable_sfp_txen(pdev, port, 1);
+
+ /* configure MV88E6176 Physical Control Port Register */
+ dev_info(&priv->client->dev,
+ "Port%d: SFP: force 1000mbps link up "
+ "(auto-negotiate duplex)\n",
+ port);
+ reg = read_switch_port(pdev, port, MV_PORT_PHYS_CONTROL);
+ reg &= ~0x3f; /* clear 5-0 */
+ reg |= (1 << 4) | (1 << 5); /* force link up */
+ reg |= 2; /* force 1000mbps */
+ write_switch_port(pdev, port, MV_PORT_PHYS_CONTROL, reg);
+ reg = read_switch_port(pdev, port, MV_PORT_PHYS_CONTROL);
+ }
+
+ /* copper */
+ else {
+ enable_sfp_txen(pdev, port, 0);
+
+ /* configure MV88E6176 Physical Control Port Register */
+ dev_info(&priv->client->dev,
+ "Port%d: Copper: set auto-neg link/duplex/speed\n",
+ port);
+ reg = read_switch_port(pdev, port, MV_PORT_PHYS_CONTROL);
+ reg &= ~0x3f; /* clear 5-0 */
+ reg |= 3; /* speed not forced */
+ write_switch_port(pdev, port, MV_PORT_PHYS_CONTROL, reg);
+ reg = read_switch_port(pdev, port, MV_PORT_PHYS_CONTROL);
+ }
+ dev_dbg(&priv->client->dev, "%s: Port%d %s PORT_PHYS_CONTROL=0x%04x\n",
+ __func__, port, sfp ? "SFP" : "copper",
+ read_switch_port(pdev, port, MV_PORT_PHYS_CONTROL));
+
+ return 0;
+}
+
+#if !IS_ENABLED(CONFIG_NET_DSA_MV88E6352) && defined(PORT_POWER_CONTROL)
+static int enable_switch_port(struct phy_device *pdev, int port, bool enable)
+{
+ struct mv88e1111_priv *priv = dev_get_drvdata(&pdev->dev);
+ u16 reg;
+
+ /* power up port */
+ dev_info(&priv->client->dev, "Port%d: %s\n", port,
+ enable ? "normal operation" : "power down");
+ reg = read_switch_port_phy(pdev, port, MV_PHY_CONTROL);
+ if (enable)
+ reg &= ~(1 << 11); /* Normal Operation */
+ else
+ reg |= (1 << 11); /* power down */
+ write_switch_port_phy(pdev, port, MV_PHY_CONTROL, reg);
+
+ reg = read_switch_port_phy(pdev, port, MV_PHY_CONTROL1);
+ if (enable)
+ reg &= ~(1 << 2); /* Normal Operation */
+ else
+ reg |= (1 << 2); /* power down */
+ write_switch_port_phy(pdev, port, MV_PHY_CONTROL1, reg);
+
+ return 0;
+}
+#endif
+
+/*
+ * Sysfs API
+ */
+
+struct mv88e1111_port_state *get_port_state(struct mv88e1111_priv *priv,
+ int port)
+{
+ if (port == 5)
+ return &priv->port5;
+ if (port == 6)
+ return &priv->port6;
+ return NULL;
+}
+
+/*
+ * get MV88E6176 port number for a specific GW16083 port name
+ * The GW16083 ports as shown on the silkscreen are not mapped according to
+ * the MV88E6176 ports numbers.
+ */
+static int gw16083_get_port(const char* name)
+{
+ int i;
+ int map[] = { 3, 2, 1, 0, 5, 6 };
+
+ if (strncasecmp(name, "LAN", 3) != 0)
+ return -1;
+ i = name[3] - '0';
+ if (i < 1 || i > 6)
+ return -1;
+ return map[i-1];
+}
+
+#if !IS_ENABLED(CONFIG_NET_DSA_MV88E6352)
+static ssize_t port_show(struct device *dev, struct device_attribute *attr,
+ char *buf)
+{
+ struct mv88e1111_priv *priv = dev_get_drvdata(dev);
+ int port = -1;
+ u16 reg;
+
+ if (sscanf(attr->attr.name, "port%d", &port) != 1)
+ return 0;
+ if (port < 0 || port > 6)
+ return 0;
+ reg = read_switch_port_phy(priv->phydev, port, MV_PHY_CONTROL);
+ return sprintf(buf, "%s\n", (reg & (1 << 11)) ? "disabled" : "enabled");
+}
+
+#if defined(PORT_POWER_CONTROL)
+static ssize_t port_store(struct device *dev, struct device_attribute *attr,
+ const char *buf, size_t count)
+{
+ struct mv88e1111_priv *priv = dev_get_drvdata(dev);
+ int port = -1;
+ int val;
+
+ port = gw16083_get_port(attr->attr.name);
+ if (port < 0)
+ return 0;
+ if (sscanf(buf, "%d", &val) != 1)
+ return 0;
+ enable_switch_port(priv->phydev, port, val ? 1 : 0);
+ return count;
+}
+
+static DEVICE_ATTR(lan1, S_IWUSR | S_IRUGO, port_show, port_store);
+static DEVICE_ATTR(lan2, S_IWUSR | S_IRUGO, port_show, port_store);
+static DEVICE_ATTR(lan3, S_IWUSR | S_IRUGO, port_show, port_store);
+static DEVICE_ATTR(lan4, S_IWUSR | S_IRUGO, port_show, port_store);
+static DEVICE_ATTR(lan5, S_IWUSR | S_IRUGO, port_show, port_store);
+static DEVICE_ATTR(lan6, S_IWUSR | S_IRUGO, port_show, port_store);
+#else
+static DEVICE_ATTR(lan1, S_IRUGO, port_show, NULL);
+static DEVICE_ATTR(lan2, S_IRUGO, port_show, NULL);
+static DEVICE_ATTR(lan3, S_IRUGO, port_show, NULL);
+static DEVICE_ATTR(lan4, S_IRUGO, port_show, NULL);
+static DEVICE_ATTR(lan5, S_IRUGO, port_show, NULL);
+static DEVICE_ATTR(lan6, S_IRUGO, port_show, NULL);
+#endif
+#endif /* #if IS_ENABLED(CONFIG_NET_DSA_MV88E6352) */
+
+static ssize_t portmode_show(struct device *dev, struct device_attribute *attr,
+ char *buf)
+{
+ struct mv88e1111_priv *priv = dev_get_drvdata(dev);
+ struct mv88e1111_port_state *state;
+
+ state = get_port_state(priv, gw16083_get_port(attr->attr.name));
+ if (!state)
+ return 0;
+
+ return sprintf(buf, "%s\n", state->serdes ? "SFP" : "RJ45");
+}
+#ifdef PORT_MODE_CONTROL
+static ssize_t portmode_store(struct device *dev, struct device_attribute *attr,
+ const char *buf, size_t count)
+{
+ struct mv88e1111_priv *priv = dev_get_drvdata(dev);
+ struct mv88e1111_port_state *state;
+ u16 reg;
+ int port;
+
+ port = gw16083_get_port(attr->attr.name);
+ state = get_port_state(priv, port);
+ if (!state)
+ return 0;
+
+ reg = read_switch_port_phy(priv->phydev, port, MII_M1111_PHY_EXT_SR);
+ if (strcasecmp(buf, "auto") == 0) {
+ reg &= ~(1<<15); /* enable auto-selection */
+ dev_info(&priv->client->dev, "Port%d: enable auto-selection\n",
+ port);
+ } else if (strcasecmp(buf, "RJ45") == 0) {
+ reg |= (1<<15); /* disable auto-selection */
+ reg |= 0xb; /* RGMII to Copper */
+ config_mv88e1111_port_sfp(priv->phydev, port, 0);
+ dev_info(&priv->client->dev, "Port%d: select RJ45\n", port);
+ } else if (strcasecmp(buf, "SFP") == 0) {
+ reg |= (1<<15); /* disable auto-selection */
+ reg |= 0x3; /* RGMII to Fiber */
+ config_mv88e1111_port_sfp(priv->phydev, port, 1);
+ dev_info(&priv->client->dev, "Port%d: select SFP\n", port);
+ }
+ write_switch_port_phy(priv->phydev, port, MII_M1111_PHY_EXT_SR, reg);
+
+ return count;
+}
+
+static DEVICE_ATTR(lan5_mode, S_IWUSR | S_IRUGO, portmode_show, portmode_store);
+static DEVICE_ATTR(lan6_mode, S_IWUSR | S_IRUGO, portmode_show, portmode_store);
+#else
+static DEVICE_ATTR(lan5_mode, S_IRUGO, portmode_show, NULL);
+static DEVICE_ATTR(lan6_mode, S_IRUGO, portmode_show, NULL);
+#endif
+
+static ssize_t portsfp_show(struct device *dev, struct device_attribute *attr,
+ char *buf)
+{
+ struct mv88e1111_priv *priv = dev_get_drvdata(dev);
+ struct mv88e1111_port_state *state;
+
+ state = get_port_state(priv, gw16083_get_port(attr->attr.name));
+ if (!state)
+ return 0;
+
+ if (!state->sfp_present)
+ return 0;
+
+ return sprintf(buf, "%s\n", state->sfp_id);
+}
+
+static DEVICE_ATTR(lan5_sfp, S_IRUGO, portsfp_show, NULL);
+static DEVICE_ATTR(lan6_sfp, S_IRUGO, portsfp_show, NULL);
+
+/*
+ * PHY driver
+ */
+
+/* check MV88E1111 PHY status and MV88E6176 GPIO */
+static void
+mv88e6176_work(struct work_struct *work)
+{
+ struct mv88e1111_priv *priv =
+ container_of(work, struct mv88e1111_priv, work.work);
+ struct phy_device *pdev = priv->phydev;
+ struct device *dev = &priv->client->dev;
+ struct mv88e1111_port_state *state;
+ bool serdes, sfp_present, sfp_signal;
+ int port;
+ u16 gpio;
+
+ mutex_lock(&pdev->lock);
+ gpio = read_switch_scratch(pdev, MV_GPIO_DATA);
+ for (port = 5; port < 7; port++) {
+ serdes = (read_switch_port_phy(pdev, port, MII_M1111_PHY_EXT_SR)
+ & (1<<13)) ? 1 : 0;
+ dev_dbg(dev, "%s: Port%d GPIO:0x%02x SerDes:%d\n",
+ __func__, port, gpio, serdes);
+ switch(port) {
+ case 5:
+ state = &priv->port5;
+ sfp_present = !((gpio >> 5) & 1);
+ sfp_signal = !((gpio >> 6) & 1);
+ break;
+ case 6:
+ state = &priv->port6;
+ sfp_present = !((gpio >> 3) & 1);
+ sfp_signal = !((gpio >> 4) & 1);
+ break;
+ }
+
+ /*
+ * on sfp_detect read/verify SFP MSA and set sfp_compat
+ * on sfp_signal issue link down?
+ * on serdes auto-select
+ */
+ if (state->sfp_present != sfp_present) {
+ state->sfp_present = sfp_present;
+ dev_info(dev, "Port%d: SFP %s\n",
+ port, sfp_present ? "inserted" : "removed");
+ if (state->sfp_present) {
+ if (gw16083_read_port_sfp(priv->client, state))
+ state->sfp_compat = false;
+ else
+ state->sfp_compat = true;
+ /* trigger a re-select/enable below */
+ state->serdes = !serdes;
+ pdev->state = PHY_RUNNING;
+ } else {
+ state->sfp_compat = false;
+ state->sfp_enabled = false;
+ pdev->state = PHY_NOLINK;
+ }
+ }
+ if (state->sfp_signal != sfp_signal) {
+ state->sfp_signal = sfp_signal;
+ dev_info(dev, "Port%d: SFP signal %s\n",
+ port, sfp_signal ? "detected" : "lost");
+ }
+ if (state->serdes != serdes) {
+ state->serdes = serdes;
+ dev_info(dev, "Port%d: %s auto-selected\n",
+ port, serdes ? "SERDES" : "copper");
+
+ /*
+ * if auto-selection has switched to copper
+ * disable serdes
+ */
+ if (!serdes) {
+ config_mv88e1111_port_sfp(pdev, port, 0);
+ state->sfp_enabled = false;
+ }
+ }
+
+ /* if compatible SFP module and not yet enabled then enable */
+ if (state->sfp_compat && state->sfp_signal &&
+ !state->sfp_enabled)
+ {
+ if (!config_mv88e1111_port_sfp(pdev, port, 1))
+ state->sfp_enabled = true;
+ }
+ }
+ mutex_unlock(&pdev->lock);
+
+ queue_delayed_work(priv->workq, &priv->work, HZ);
+}
+
+static int
+mv88e6176_read_status(struct phy_device *pdev)
+{
+ return 0;
+}
+
+static int
+mv88e6176_config_aneg(struct phy_device *pdev)
+{
+ return 0;
+}
+
+static int
+mv88e6176_config_init(struct phy_device *pdev)
+{
+ pdev->state = PHY_RUNNING;
+
+ return 0;
+}
+
+static void
+mv88e6176_remove(struct phy_device *pdev)
+{
+ struct mv88e1111_priv *priv = dev_get_drvdata(&pdev->dev);
+
+ dev_dbg(&priv->client->dev, "%s", __func__);
+
+ destroy_workqueue(priv->workq);
+#if !IS_ENABLED(CONFIG_NET_DSA_MV88E6352)
+ device_remove_file(&pdev->dev, &dev_attr_lan1);
+ device_remove_file(&pdev->dev, &dev_attr_lan2);
+ device_remove_file(&pdev->dev, &dev_attr_lan3);
+ device_remove_file(&pdev->dev, &dev_attr_lan4);
+ device_remove_file(&pdev->dev, &dev_attr_lan5);
+ device_remove_file(&pdev->dev, &dev_attr_lan6);
+#endif
+ device_remove_file(&pdev->dev, &dev_attr_lan5_sfp);
+ device_remove_file(&pdev->dev, &dev_attr_lan6_sfp);
+ device_remove_file(&pdev->dev, &dev_attr_lan5_mode);
+ device_remove_file(&pdev->dev, &dev_attr_lan6_mode);
+ sysfs_remove_link(kernel_kobj, "gw16083");
+}
+
+/*
+ * mv88e6176_probe - called any time an MV88E6176 is found on an mdio bus
+ * Determine if this MV88E6176 is indeed on a GW16083 and if so configure
+ * the port5/port6 phy and register a background procedure for monitoring
+ * their states to support SFP vs Copper switching.
+ *
+ * Verify this is a GW16083 by ensuring:
+ * - the phy address matches that of a GW16083
+ * - the mdio bus is from an i210 device (igb driver)
+ * - there are MV881111 PHY's hanging off of Port5 and Port6
+ */
+static int
+mv88e6176_probe(struct phy_device *pdev)
+{
+ int port;
+ int ret = 0;
+ u32 id, reg;
+ struct mv88e1111_priv *priv;
+ struct device *dev;
+#if IS_ENABLED(CONFIG_NET_DSA_MV88E6352)
+ struct net_device *netdev = NULL;
+#endif
+
+ dev_dbg(&pdev->dev, "%s: addr=0x%02x bus=%s:%s gw16083_client=%p\n",
+ __func__, pdev->addr, pdev->bus->name, pdev->bus->id,
+ gw16083_client);
+
+ /* In single-chip addressing mode the MV88E6176 shows up on 0x10-0x16 */
+ if (pdev->addr != MV_BASE)
+ return 0;
+
+ /* i2c driver needs to be loaded first */
+ if (!gw16083_client)
+ return 0;
+ dev = &gw16083_client->dev;
+
+ /* gw16083 has MV88E1676 hanging off of i210 mdio bus */
+ if (strcmp(pdev->bus->name, "igb_enet_mii_bus") != 0)
+ return 0;
+
+ /* verify Port5/Port6 have an MV88E1111 PHY hanging off them */
+ for (port = 5; port < 7; port++) {
+ id = read_switch_port_phy(pdev, port,
+ MII_M1111_PHY_IDENT0) << 16;
+ id |= read_switch_port_phy(pdev, port, MII_M1111_PHY_IDENT1);
+ if ((id & MII_M1111_PHY_ID_MASK) != MII_M1111_PHY_ID) {
+ dev_err(dev, "Port%d: No MV88E1111 PHY detected", port);
+ return 0;
+ }
+ }
+
+#if IS_ENABLED(CONFIG_NET_DSA_MV88E6352)
+ /*
+ * Find the netdev this bus is hanging off of and register with DSA:
+ * The netdev must be an Intel I210 (igb) with Gateworks MAC addr
+ */
+ read_lock(&dev_base_lock);
+ for_each_netdev(&init_net, netdev) {
+ if (netdev->dev.parent &&
+ !strcmp(netdev->dev.parent->driver->name, "igb") &&
+ (netdev->perm_addr[0] == 0x00) &&
+ (netdev->perm_addr[1] == 0xd0) &&
+ (netdev->perm_addr[2] == 0x12))
+ {
+ switch_plat_data.netdev = &netdev->dev;
+ switch_plat_data.chip[0].host_dev = &pdev->bus->dev;
+ break;
+ }
+ }
+ read_unlock(&dev_base_lock);
+
+ if (switch_plat_data.netdev) {
+ platform_device_register(&switch_device);
+ dev_info(dev, "registered GW16083 DSA switch\n");
+ } else {
+ dev_err(dev, "failed to find netdev for DSA switch\n");
+ }
+#endif
+
+ /*
+ * port5/6 config: MV88E1111 PHY
+ * Register 20: PHY Control Register
+ * R20_7: add delay to RX_CLK for RXD
+ * R20_1: add delay to TX_CLK for TXD
+ * Register 24: LED Control Register
+ * 0x4111:
+ * Pulse stretch 170 to 340 ms
+ * Register 0: Control Register
+ * R0_15: phy reset
+ */
+ dev_info(dev, "Configuring MV88E6176 7-port switch");
+ for (port = 5; port < 7; port++) {
+#ifdef RGMII_DELAY_ON_PHY
+ /* phy rx/tx delay */
+ reg = read_switch_port_phy(pdev, port, MII_M1111_PHY_EXT_CR);
+ reg |= (1<<1) | (1<<7);
+ write_switch_port_phy(pdev, port, MII_M1111_PHY_EXT_CR, reg);
+#else
+ write_switch_port(pdev, port, MV_PORT_PHYS_CONTROL, 0xC003);
+#endif
+
+ /* led config */
+ write_switch_port_phy(pdev, port, MII_M1111_PHY_LED_CONTROL,
+ MII_M1111_PHY_LED_PULSE_STR);
+ /* reset phy */
+ reg = read_switch_port_phy(pdev, port, MII_M1111_PHY_CONTROL);
+ reg |= MII_M1111_PHY_CONTROL_RESET;
+ write_switch_port_phy(pdev, port, MII_M1111_PHY_CONTROL, reg);
+ dev_info(dev, "Port%d: MV88E111 PHY configured\n", port);
+ }
+
+ /*
+ * GPIO Configuration:
+ * GPIO1: FIB5_TXEN# (output)
+ * GPIO2: FIB6_TXEN# (output)
+ * GPIO3: FIB6_PRES# (input)
+ * GPIO4: FIB6_LOS (input)
+ * GPIO5: FIB5_PRES# (input)
+ * GPIO6: FIB5_LOS (input)
+ */
+ write_switch_scratch(pdev, MV_GPIO_DATA, 0x06); /* GPIO[2:1] out hi */
+ write_switch_scratch(pdev, MV_GPIO_DIR, 0x78); /* GPIO[6:3] inp */
+
+ pdev->irq = PHY_POLL;
+
+ priv = devm_kzalloc(&pdev->dev, sizeof(*priv), GFP_KERNEL);
+ if (!priv)
+ return -ENOMEM;
+ memset(priv, 0, sizeof(*priv));
+ priv->phydev = pdev;
+ priv->client = gw16083_client;
+ priv->port5.port = 5;
+ priv->port6.port = 6;
+ dev_set_drvdata(&pdev->dev, priv);
+
+ /* register sysfs API */
+#if !IS_ENABLED(CONFIG_NET_DSA_MV88E6352)
+ ret |= device_create_file(&pdev->dev, &dev_attr_lan1);
+ ret |= device_create_file(&pdev->dev, &dev_attr_lan2);
+ ret |= device_create_file(&pdev->dev, &dev_attr_lan3);
+ ret |= device_create_file(&pdev->dev, &dev_attr_lan4);
+ ret |= device_create_file(&pdev->dev, &dev_attr_lan5);
+ ret |= device_create_file(&pdev->dev, &dev_attr_lan6);
+#endif
+ ret |= device_create_file(&pdev->dev, &dev_attr_lan5_sfp);
+ ret |= device_create_file(&pdev->dev, &dev_attr_lan6_sfp);
+ ret |= device_create_file(&pdev->dev, &dev_attr_lan5_mode);
+ ret |= device_create_file(&pdev->dev, &dev_attr_lan6_mode);
+
+ if (unlikely(ret))
+ dev_err(&pdev->dev, "Failed creating attrs\n");
+
+ /* Add a nice symlink to the real device */
+ ret = sysfs_create_link(kernel_kobj, &pdev->dev.kobj, "gw16083");
+
+ INIT_DELAYED_WORK(&priv->work, mv88e6176_work);
+ priv->workq = create_singlethread_workqueue("gw16083");
+ if (!priv->workq)
+ return -ENODEV;
+ queue_delayed_work(priv->workq, &priv->work, 0);
+
+ dev_dbg(dev, "initial state: GPIO=0x%02x "
+ "Port5_serdes=%d Port6_serdes=%d\n",
+ read_switch_scratch(pdev, MV_GPIO_DATA),
+ (read_switch_port_phy(pdev, 5, MII_M1111_PHY_EXT_SR)
+ & (1<<13) ? 1:0),
+ (read_switch_port_phy(pdev, 6, MII_M1111_PHY_EXT_SR)
+ & (1<<13) ? 1:0));
+
+ return ret;
+}
+
+static struct phy_driver mv88e6176_phy_driver = {
+ .name = "gw16083",
+ .phy_id = MV_IDENT_VALUE,
+ .phy_id_mask = MV_IDENT_MASK,
+ .features = PHY_BASIC_FEATURES,
+ .probe = &mv88e6176_probe,
+ .remove = &mv88e6176_remove,
+ .config_init = &mv88e6176_config_init,
+ .config_aneg = &mv88e6176_config_aneg,
+ .read_status = &mv88e6176_read_status,
+ .driver = { .owner = THIS_MODULE },
+};
+
+/*
+ * I2C driver
+ */
+
+/* See SFF-8472 */
+struct sfp_msa {
+ /* Basic ID fields */
+ u8 identifier;
+ u8 ext_identifier;
+ u8 connector;
+ u8 transceiver[8];
+ u8 encoding;
+ u8 br_nominal;
+ u8 rate_identifier;
+ u8 length_smf_km;
+ u8 length_smf;
+ u8 length_om2;
+ u8 length_om1;
+ u8 length_om4;
+ u8 length_om3;
+ u8 vendor_name[16];
+ u8 transceiver2;
+ u8 vendor_oui[3];
+ u8 vendor_pn[16];
+ u8 vendor_rev[4];
+ u8 wavelength[2];
+ u8 resv1;
+ u8 cc_base;
+
+ /* extended id fields */
+ u8 options[2];
+ u8 br_max;
+ u8 br_min;
+ u8 vendor_sn[16];
+ u8 date_code[8];
+ u8 diags_type;
+ u8 enhanced_options;
+ u8 sff8472_compliance;
+ u8 cc_ext;
+
+ /* Vendor specific ID fields */
+ u8 vendor_data[32];
+ u8 sff8079[128];
+};
+
+enum identifier {
+ UNKNOWN,
+ GBIC,
+ SFF,
+ SFP,
+ XBI,
+ XENPACK,
+ XFP,
+ XFF,
+ XFP_E,
+ XPAK,
+ X2,
+ DWDM_SFP,
+ QSFP,
+ MAX_ID,
+};
+
+const char* id_names[] = {
+ "UNKONWN",
+ "GBIC",
+ "SFF",
+ "SFP",
+ NULL,
+};
+
+/* Flags for SFP modules compatible with ETH up to 1Gb */
+struct sfp_flags {
+ u8 e1000_base_sx:1;
+ u8 e1000_base_lx:1;
+ u8 e1000_base_cx:1;
+ u8 e1000_base_t:1;
+ u8 e100_base_lx:1;
+ u8 e100_base_fx:1;
+ u8 e10_base_bx10:1;
+ u8 e10_base_px:1;
+};
+
+#define STRING_APPEND(str, src) \
+ strncat(str, src, sizeof(src)); \
+ for (i = 1; i < sizeof(str); i++) \
+ if (str[i-1] == ' ' && str[i] == ' ') \
+ str[i] = 0;
+
+static int gw16083_read_port_sfp(struct i2c_client *client,
+ struct mv88e1111_port_state *state)
+{
+ int ret = 0;
+ u8 data[256];
+ struct sfp_flags *eth_flags;
+ u8 crc;
+ int i;
+ u8 *str;
+ struct sfp_msa *sfp_msa = (struct sfp_msa *)data;
+ int port = state->port;
+ union i2c_smbus_data d;
+
+ dev_dbg(&client->dev, "%s Port%d\n", __func__, port);
+ if (!i2c_check_functionality(client->adapter,
+ I2C_FUNC_SMBUS_READ_I2C_BLOCK))
+ return -ENODEV;
+ d.byte = (port == 5) ? 1 : 2;
+ if (i2c_smbus_xfer(client->adapter, GW16083_I2C_ADDR_PCA9543,
+ client->flags, I2C_SMBUS_WRITE, 0,
+ I2C_SMBUS_BYTE_DATA, &d) < 0)
+ {
+ dev_err(&client->dev,
+ "Port%d: failed writing PCA9543 register\n", port);
+ return ret;
+ }
+
+ /* read all 256 bytes of SFP EEPROM */
+ for (i = 0; i < sizeof(data); i += I2C_SMBUS_BLOCK_MAX) {
+ d.block[0] = I2C_SMBUS_BLOCK_MAX;
+ if (i2c_smbus_xfer(client->adapter, GW16083_I2C_ADDR_SFP1,
+ client->flags, I2C_SMBUS_READ, i,
+ I2C_SMBUS_I2C_BLOCK_DATA, &d) < 0)
+ {
+ dev_err(&client->dev,
+ "Port%d: failed reading SFP data\n", port);
+ return ret;
+ }
+ memcpy(data + i, d.block + 1, I2C_SMBUS_BLOCK_MAX);
+ }
+
+ /* Validate checksums */
+ for (crc = 0, i = 0; i < 63; i++)
+ crc += data[i];
+ if (crc != sfp_msa->cc_base) {
+ dev_err(&client->dev, "Port%d: "
+ "Checksum failure for Base ID fields: 0x%02x\n", port,
+ crc);
+#ifdef FAIL_ON_CHECKSUM_ERR
+ return -EINVAL;
+#endif
+ }
+ for (crc = 0, i = 64; i < 95; i++)
+ crc += data[i];
+ if (crc != sfp_msa->cc_ext) {
+ dev_err(&client->dev, "Port%d: "
+ "Checksum failure for Extended ID fields: 0x%02x\n",
+ port, crc);
+#ifdef FAIL_ON_CHECKSUM_ERR
+ return -EINVAL;
+#endif
+ }
+ state->sfp_id[0] = 0;
+ for (i = 0; id_names[i]; i++) {
+ if (sfp_msa->identifier == i) {
+ sprintf(state->sfp_id, "%s: ", id_names[i]);
+ break;
+ }
+ }
+ STRING_APPEND(state->sfp_id, sfp_msa->vendor_oui);
+ STRING_APPEND(state->sfp_id, sfp_msa->vendor_name);
+ STRING_APPEND(state->sfp_id, sfp_msa->vendor_pn);
+ STRING_APPEND(state->sfp_id, sfp_msa->vendor_rev);
+ STRING_APPEND(state->sfp_id, sfp_msa->vendor_sn);
+ dev_info(&client->dev, "Port%d: %s\n", port, state->sfp_id);
+
+ if ((sfp_msa->identifier != GBIC) &&
+ (sfp_msa->identifier != SFF) &&
+ (sfp_msa->identifier != SFP))
+ {
+ dev_err(&client->dev, "Port%d: Unknown module identifier: %d\n",
+ port, sfp_msa->identifier);
+ return -EINVAL;
+ }
+
+ str = "";
+ eth_flags = (struct sfp_flags *)(sfp_msa->transceiver + 3);
+ if (eth_flags->e1000_base_sx) {
+ str = "1000Base-SX (Fiber)";
+ } else if (eth_flags->e1000_base_lx) {
+ str = "1000Base-LX (Fiber)";
+ } else if (eth_flags->e1000_base_t) {
+ str = "1000Base-T (Copper)";
+ } else if (eth_flags->e100_base_fx) {
+ str = "100Base-FX (Fiber) - not supported";
+ ret = -EINVAL;
+ } else {
+ str = "Unknown/Unsupported media type";
+ ret = -EINVAL;
+ }
+ if (ret)
+ dev_err(&client->dev, "Port%d: %s (0x%02x)\n", port, str,
+ sfp_msa->transceiver[3]);
+ else
+ dev_info(&client->dev, "Port%d: %s (0x%02x)\n", port, str,
+ sfp_msa->transceiver[3]);
+
+ return ret;
+}
+
+static int gw16083_probe(struct i2c_client *client,
+ const struct i2c_device_id *id)
+{
+ int ret;
+
+ dev_info(&client->dev, "GW16083 Ethernet Expansion Mezzanine\n");
+ if (gw16083_client) {
+ dev_err(&client->dev, "client already registered\n");
+ return -EINVAL;
+ }
+ gw16083_client = client;
+
+ ret = phy_driver_register(&mv88e6176_phy_driver);
+ if (ret)
+ dev_err(&client->dev,
+ "failed to register mv88e6176 phy driver: %d\n", ret);
+ return ret;
+}
+
+static int gw16083_remove(struct i2c_client *client)
+{
+ dev_dbg(&client->dev, "%s\n", __func__);
+
+ phy_driver_unregister(&mv88e6176_phy_driver);
+ gw16083_client = NULL;
+ return 0;
+}
+
+static const struct of_device_id gw16083_dt_ids[] = {
+ { .compatible = "gateworks,gw16083", },
+ { }
+};
+
+MODULE_DEVICE_TABLE(of, gw16083_dt_ids);
+
+static const struct i2c_device_id gw16083_id[] = {
+ { "gw16083", 0 },
+ { }
+};
+MODULE_DEVICE_TABLE(i2c, gw16083_id);
+
+static struct i2c_driver gw16083_driver = {
+ .driver = {
+ .name = "gw16083",
+ .of_match_table = gw16083_dt_ids,
+ },
+ .probe = gw16083_probe,
+ .remove = gw16083_remove,
+ .id_table = gw16083_id,
+};
+
+static int __init mv88e6176_init(void)
+{
+ return i2c_add_driver(&gw16083_driver);
+}
+
+static void __exit mv88e6176_exit(void)
+{
+ i2c_del_driver(&gw16083_driver);
+}
+
+module_init(mv88e6176_init);
+module_exit(mv88e6176_exit);
diff --git a/target/linux/imx6/files-4.3/drivers/net/phy/gw16083.h b/target/linux/imx6/files-4.3/drivers/net/phy/gw16083.h
new file mode 100644
index 0000000..db96f2b
--- /dev/null
+++ b/target/linux/imx6/files-4.3/drivers/net/phy/gw16083.h
@@ -0,0 +1,123 @@
+/*
+ * drivers/net/phy/mv88e6176.h
+ *
+ * Driver for Marvell Switch
+ *
+ * Author: Tim Harvey
+ *
+ * Copyright (c) 2014 Tim Harvey <tharvey at gateworks.com>
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License as published by the
+ * Free Software Foundation; either version 2 of the License, or (at your
+ * option) any later version.
+ *
+ */
+
+#ifndef _GW16083_H_
+#define _GW16083_H_
+
+#define MII_MARVELL_PHY_PAGE 22
+
+/*
+ * I2C Addresses
+ */
+#define GW16083_I2C_ADDR_SFP1 0x50
+#define GW16083_I2C_ADDR_SFP2 0x51
+#define GW16083_I2C_ADDR_EEPROM 0x52
+#define GW16083_I2C_ADDR_PCA9543 0x70
+
+/*
+ * MV88E1111 PHY Registers
+ */
+enum {
+ MII_M1111_PHY_CONTROL = 0,
+ MII_M1111_PHY_STATUS = 1,
+ MII_M1111_PHY_IDENT0 = 2,
+ MII_M1111_PHY_IDENT1 = 3,
+ MII_M1111_PHY_EXT_CR = 20,
+ MII_M1111_PHY_LED_CONTROL = 24,
+ MII_M1111_PHY_EXT_SR = 27,
+};
+
+#define MII_M1111_PHY_ID_MASK 0xfffffff0
+#define MII_M1111_PHY_ID 0x01410cc0
+
+#define MII_M1111_PHY_CONTROL_RESET (1 << 15)
+#define MII_M1111_PHY_LED_DIRECT 0x4100
+#define MII_M1111_PHY_LED_PULSE_STR 0x4111
+#define MII_M1111_PHY_LED_COMBINE 0x411c
+#define MII_M1111_RX_DELAY 0x80
+#define MII_M1111_TX_DELAY 0x2
+
+/*
+ * MV88E6176 Switch Registers
+ */
+
+/* PHY Addrs */
+#define MV_BASE 0x10
+#define MV_GLOBAL1 0x1b
+#define MV_GLOBAL2 0x1c
+#define MV_GLOBAL3 0x1d
+
+/* Global2 Registers */
+enum {
+ MV_SMI_PHY_COMMAND = 0x18,
+ MV_SMI_PHY_DATA = 0x19,
+ MV_SCRATCH_MISC = 0x1A,
+};
+
+/* Scratch And Misc Reg offsets */
+enum {
+ MV_GPIO_MODE = 0x60,
+ MV_GPIO_DIR = 0x62,
+ MV_GPIO_DATA = 0x64,
+ MV_GPIO76_CNTL = 0x6B,
+ MV_GPIO54_CNTL = 0x6A,
+ MV_GPIO32_CNTL = 0x69,
+ MV_GPIO10_CNTL = 0x68,
+ MV_CONFIG0 = 0x70,
+ MV_CONFIG1 = 0x71,
+ MV_CONFIG2 = 0x72,
+ MV_CONFIG3 = 0x73,
+};
+
+/* PHY Registers */
+enum {
+ MV_PHY_CONTROL = 0x00,
+ MV_PHY_STATUS = 0x01,
+ MV_PHY_IDENT0 = 0x02,
+ MV_PHY_IDENT1 = 0x03,
+ MV_PHY_ANEG = 0x04,
+ MV_PHY_LINK_ABILITY = 0x05,
+ MV_PHY_ANEG_EXPAND = 0x06,
+ MV_PHY_XMIT_NEXTP = 0x07,
+ MV_PHY_LINK_NEXTP = 0x08,
+ MV_PHY_CONTROL1 = 0x10,
+ MV_PHY_STATUS1 = 0x11,
+ MV_PHY_INTR_EN = 0x12,
+};
+
+/* Port Registers */
+enum {
+ MV_PORT_STATUS = 0x00,
+ MV_PORT_PHYS_CONTROL = 0x01,
+ MV_PORT_IDENT = 0x03,
+ MV_PORT_CONTROL = 0x04,
+ MV_PORT_VLANMAP = 0x06,
+ MV_PORT_ASSOC = 0x0b,
+ MV_PORT_RXCOUNT = 0x10,
+ MV_PORT_TXCOUNT = 0x11,
+};
+
+#define SMIBUSY (1<<15)
+#define SMIMODE22 (1<<12)
+#define SMIOP_READ (2<<10)
+#define SMIOP_WRITE (1<<10)
+#define DEVADDR 5
+#define REGADDR 0
+
+#define MV_IDENT_MASK 0x0000fff0
+#define MV_IDENT_VALUE 0x00001760
+
+#endif /* _GW16083_H_ */
diff --git a/target/linux/imx6/patches-4.3/035-ARM-dts-imx-ventana-set-GW54xx-PMIC-swbst-regulator-.patch b/target/linux/imx6/patches-4.3/035-ARM-dts-imx-ventana-set-GW54xx-PMIC-swbst-regulator-.patch
new file mode 100644
index 0000000..a92e0f8
--- /dev/null
+++ b/target/linux/imx6/patches-4.3/035-ARM-dts-imx-ventana-set-GW54xx-PMIC-swbst-regulator-.patch
@@ -0,0 +1,28 @@
+From 57b82d9e79d77442bae3d2c13b98ceccb39fe5e2 Mon Sep 17 00:00:00 2001
+From: Tim Harvey <tharvey at gateworks.com>
+Date: Thu, 5 Nov 2015 10:49:31 -0800
+Subject: [PATCH 1/3] ARM: dts: imx: ventana: set GW54xx PMIC swbst regulator
+ as always-on
+
+The GW54xx PMIC swbst regulator is used for LVDS power, CANbus xceiver
+and HDMI DDC and is enabled by the bootloader. Set the regulator to
+always-on so that Linux doesn't turn it off thinking its not needed.
+
+Signed-off-by: Tim Harvey <tharvey at gateworks.com>
+---
+ arch/arm/boot/dts/imx6qdl-gw54xx.dtsi | 2 ++
+ 1 file changed, 2 insertions(+)
+
+Index: linux-4.3/arch/arm/boot/dts/imx6qdl-gw54xx.dtsi
+===================================================================
+--- linux-4.3.orig/arch/arm/boot/dts/imx6qdl-gw54xx.dtsi 2015-11-01 16:05:25.000000000 -0800
++++ linux-4.3/arch/arm/boot/dts/imx6qdl-gw54xx.dtsi 2015-12-18 10:43:37.000000000 -0800
+@@ -260,6 +260,8 @@
+ swbst_reg: swbst {
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5150000>;
++ regulator-boot-on;
++ regulator-always-on;
+ };
+
+ snvs_reg: vsnvs {
diff --git a/target/linux/imx6/patches-4.3/036-ARM-dts-imx-ventana-fix-GW53xx-GW54xx-lvds-channel.patch b/target/linux/imx6/patches-4.3/036-ARM-dts-imx-ventana-fix-GW53xx-GW54xx-lvds-channel.patch
new file mode 100644
index 0000000..2768b09
--- /dev/null
+++ b/target/linux/imx6/patches-4.3/036-ARM-dts-imx-ventana-fix-GW53xx-GW54xx-lvds-channel.patch
@@ -0,0 +1,37 @@
+From 473d0353979db3673a7aa365265ba9b00decd414 Mon Sep 17 00:00:00 2001
+From: Tim Harvey <tharvey at gateworks.com>
+Date: Thu, 5 Nov 2015 10:52:53 -0800
+Subject: [PATCH 2/3] ARM: dts: imx: ventana: fix GW53xx/GW54xx lvds channel
+
+Signed-off-by: Tim Harvey <tharvey at gateworks.com>
+---
+ arch/arm/boot/dts/imx6qdl-gw53xx.dtsi | 2 +-
+ arch/arm/boot/dts/imx6qdl-gw54xx.dtsi | 2 +-
+ 2 files changed, 2 insertions(+), 2 deletions(-)
+
+Index: linux-4.3/arch/arm/boot/dts/imx6qdl-gw53xx.dtsi
+===================================================================
+--- linux-4.3.orig/arch/arm/boot/dts/imx6qdl-gw53xx.dtsi 2015-11-01 16:05:25.000000000 -0800
++++ linux-4.3/arch/arm/boot/dts/imx6qdl-gw53xx.dtsi 2015-12-18 10:43:32.000000000 -0800
+@@ -247,7 +247,7 @@
+ &ldb {
+ status = "okay";
+
+- lvds-channel at 1 {
++ lvds-channel at 0 {
+ fsl,data-mapping = "spwg";
+ fsl,data-width = <18>;
+ status = "okay";
+Index: linux-4.3/arch/arm/boot/dts/imx6qdl-gw54xx.dtsi
+===================================================================
+--- linux-4.3.orig/arch/arm/boot/dts/imx6qdl-gw54xx.dtsi 2015-12-18 10:39:44.855158318 -0800
++++ linux-4.3/arch/arm/boot/dts/imx6qdl-gw54xx.dtsi 2015-12-18 10:43:32.000000000 -0800
+@@ -338,7 +338,7 @@
+ &ldb {
+ status = "okay";
+
+- lvds-channel at 1 {
++ lvds-channel at 0 {
+ fsl,data-mapping = "spwg";
+ fsl,data-width = <18>;
+ status = "okay";
diff --git a/target/linux/imx6/patches-4.3/037-ARM-dts-imx-ventana-fix-GW53xx-GW54xx-lvds-channel.patch b/target/linux/imx6/patches-4.3/037-ARM-dts-imx-ventana-fix-GW53xx-GW54xx-lvds-channel.patch
new file mode 100644
index 0000000..768648e
--- /dev/null
+++ b/target/linux/imx6/patches-4.3/037-ARM-dts-imx-ventana-fix-GW53xx-GW54xx-lvds-channel.patch
@@ -0,0 +1,76 @@
+From d86b202436b6f3111c4c37b8701daa0764d2ca55 Mon Sep 17 00:00:00 2001
+From: Tim Harvey <tharvey at gateworks.com>
+Date: Thu, 5 Nov 2015 11:10:00 -0800
+Subject: [PATCH 3/3] ARM: dts: imx: ventana: Allow HDMI and LVDS to work
+ simultaneously
+
+Currently it is not possible to have HDMI and LVDS working simultaneously,
+because both ports try to use PLL5.
+
+Move the LVDS clock parent to PLL3_USB_OTG, so that HDMI and LVDS can be
+driven from independent sources.
+
+With this change the LDB pixel clock goes to 68.57 MHz, which is still
+within the valid range for the displays supported by the Ventana boards.
+
+Signed-off-by: Tim Harvey <tharvey at gateworks.com>
+---
+ arch/arm/boot/dts/imx6qdl-gw52xx.dtsi | 7 +++++++
+ arch/arm/boot/dts/imx6qdl-gw53xx.dtsi | 7 +++++++
+ arch/arm/boot/dts/imx6qdl-gw54xx.dtsi | 7 +++++++
+ 3 files changed, 21 insertions(+)
+
+Index: linux-4.3/arch/arm/boot/dts/imx6qdl-gw52xx.dtsi
+===================================================================
+--- linux-4.3.orig/arch/arm/boot/dts/imx6qdl-gw52xx.dtsi 2015-11-01 16:05:25.000000000 -0800
++++ linux-4.3/arch/arm/boot/dts/imx6qdl-gw52xx.dtsi 2015-12-18 10:43:32.000000000 -0800
+@@ -151,6 +151,13 @@
+ status = "okay";
+ };
+
++&clks {
++ assigned-clocks = <&clks IMX6QDL_CLK_LDB_DI0_SEL>,
++ <&clks IMX6QDL_CLK_LDB_DI1_SEL>;
++ assigned-clock-parents = <&clks IMX6QDL_CLK_PLL3_USB_OTG>,
++ <&clks IMX6QDL_CLK_PLL3_USB_OTG>;
++};
++
+ &fec {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_enet>;
+Index: linux-4.3/arch/arm/boot/dts/imx6qdl-gw53xx.dtsi
+===================================================================
+--- linux-4.3.orig/arch/arm/boot/dts/imx6qdl-gw53xx.dtsi 2015-12-18 10:39:44.867158318 -0800
++++ linux-4.3/arch/arm/boot/dts/imx6qdl-gw53xx.dtsi 2015-12-18 10:43:32.000000000 -0800
+@@ -152,6 +152,13 @@
+ status = "okay";
+ };
+
++&clks {
++ assigned-clocks = <&clks IMX6QDL_CLK_LDB_DI0_SEL>,
++ <&clks IMX6QDL_CLK_LDB_DI1_SEL>;
++ assigned-clock-parents = <&clks IMX6QDL_CLK_PLL3_USB_OTG>,
++ <&clks IMX6QDL_CLK_PLL3_USB_OTG>;
++};
++
+ &fec {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_enet>;
+Index: linux-4.3/arch/arm/boot/dts/imx6qdl-gw54xx.dtsi
+===================================================================
+--- linux-4.3.orig/arch/arm/boot/dts/imx6qdl-gw54xx.dtsi 2015-12-18 10:39:44.871158318 -0800
++++ linux-4.3/arch/arm/boot/dts/imx6qdl-gw54xx.dtsi 2015-12-18 10:43:32.000000000 -0800
+@@ -142,6 +142,13 @@
+ status = "okay";
+ };
+
++&clks {
++ assigned-clocks = <&clks IMX6QDL_CLK_LDB_DI0_SEL>,
++ <&clks IMX6QDL_CLK_LDB_DI1_SEL>;
++ assigned-clock-parents = <&clks IMX6QDL_CLK_PLL3_USB_OTG>,
++ <&clks IMX6QDL_CLK_PLL3_USB_OTG>;
++};
++
+ &fec {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_enet>;
diff --git a/target/linux/imx6/patches-4.3/100-bootargs.patch b/target/linux/imx6/patches-4.3/100-bootargs.patch
new file mode 100644
index 0000000..3c22ec7
--- /dev/null
+++ b/target/linux/imx6/patches-4.3/100-bootargs.patch
@@ -0,0 +1,13 @@
+Index: linux-4.3/arch/arm/boot/dts/imx6dl-wandboard.dts
+===================================================================
+--- linux-4.3.orig/arch/arm/boot/dts/imx6dl-wandboard.dts 2015-11-01 16:05:25.000000000 -0800
++++ linux-4.3/arch/arm/boot/dts/imx6dl-wandboard.dts 2015-12-18 10:39:44.923158318 -0800
+@@ -19,4 +19,8 @@
+ memory {
+ reg = <0x10000000 0x40000000>;
+ };
++
++ chosen {
++ bootargs = "console=ttymxc0,115200";
++ };
+ };
diff --git a/target/linux/imx6/patches-4.3/202-net-igb-add-i210-i211-support-for-phy-read-write.patch b/target/linux/imx6/patches-4.3/202-net-igb-add-i210-i211-support-for-phy-read-write.patch
new file mode 100644
index 0000000..6a636a3
--- /dev/null
+++ b/target/linux/imx6/patches-4.3/202-net-igb-add-i210-i211-support-for-phy-read-write.patch
@@ -0,0 +1,131 @@
+Author: Tim Harvey <tharvey at gateworks.com>
+Date: Thu May 15 00:12:26 2014 -0700
+
+ net: igb: add i210/i211 support for phy read/write
+
+ The i210/i211 uses the MDICNFG register for the phy address instead of the
+ MDIC register.
+
+ Signed-off-by: Tim Harvey <tharvey at gateworks.com>
+
+Index: linux-4.3/drivers/net/ethernet/intel/igb/e1000_phy.c
+===================================================================
+--- linux-4.3.orig/drivers/net/ethernet/intel/igb/e1000_phy.c 2015-11-01 16:05:25.000000000 -0800
++++ linux-4.3/drivers/net/ethernet/intel/igb/e1000_phy.c 2015-12-18 10:43:28.000000000 -0800
+@@ -129,7 +129,7 @@
+ s32 igb_read_phy_reg_mdic(struct e1000_hw *hw, u32 offset, u16 *data)
+ {
+ struct e1000_phy_info *phy = &hw->phy;
+- u32 i, mdic = 0;
++ u32 i, mdicnfg, mdic = 0;
+ s32 ret_val = 0;
+
+ if (offset > MAX_PHY_REG_ADDRESS) {
+@@ -142,11 +142,25 @@
+ * Control register. The MAC will take care of interfacing with the
+ * PHY to retrieve the desired data.
+ */
+- mdic = ((offset << E1000_MDIC_REG_SHIFT) |
+- (phy->addr << E1000_MDIC_PHY_SHIFT) |
+- (E1000_MDIC_OP_READ));
++ switch (hw->mac.type) {
++ case e1000_i210:
++ case e1000_i211:
++ mdicnfg = rd32(E1000_MDICNFG);
++ mdicnfg &= ~(E1000_MDICNFG_PHY_MASK);
++ mdicnfg |= (phy->addr << E1000_MDICNFG_PHY_SHIFT);
++ wr32(E1000_MDICNFG, mdicnfg);
++ mdic = ((offset << E1000_MDIC_REG_SHIFT) |
++ (E1000_MDIC_OP_READ));
++ break;
++ default:
++ mdic = ((offset << E1000_MDIC_REG_SHIFT) |
++ (phy->addr << E1000_MDIC_PHY_SHIFT) |
++ (E1000_MDIC_OP_READ));
++ break;
++ }
+
+ wr32(E1000_MDIC, mdic);
++ wrfl();
+
+ /* Poll the ready bit to see if the MDI read completed
+ * Increasing the time out as testing showed failures with
+@@ -171,6 +185,18 @@
+ *data = (u16) mdic;
+
+ out:
++ switch (hw->mac.type) {
++ /* restore MDICNFG to have phy's addr */
++ case e1000_i210:
++ case e1000_i211:
++ mdicnfg = rd32(E1000_MDICNFG);
++ mdicnfg &= ~(E1000_MDICNFG_PHY_MASK);
++ mdicnfg |= (hw->phy.addr << E1000_MDICNFG_PHY_SHIFT);
++ wr32(E1000_MDICNFG, mdicnfg);
++ break;
++ default:
++ break;
++ }
+ return ret_val;
+ }
+
+@@ -185,7 +211,7 @@
+ s32 igb_write_phy_reg_mdic(struct e1000_hw *hw, u32 offset, u16 data)
+ {
+ struct e1000_phy_info *phy = &hw->phy;
+- u32 i, mdic = 0;
++ u32 i, mdicnfg, mdic = 0;
+ s32 ret_val = 0;
+
+ if (offset > MAX_PHY_REG_ADDRESS) {
+@@ -198,12 +224,27 @@
+ * Control register. The MAC will take care of interfacing with the
+ * PHY to retrieve the desired data.
+ */
+- mdic = (((u32)data) |
+- (offset << E1000_MDIC_REG_SHIFT) |
+- (phy->addr << E1000_MDIC_PHY_SHIFT) |
+- (E1000_MDIC_OP_WRITE));
++ switch (hw->mac.type) {
++ case e1000_i210:
++ case e1000_i211:
++ mdicnfg = rd32(E1000_MDICNFG);
++ mdicnfg &= ~(E1000_MDICNFG_PHY_MASK);
++ mdicnfg |= (phy->addr << E1000_MDICNFG_PHY_SHIFT);
++ wr32(E1000_MDICNFG, mdicnfg);
++ mdic = (((u32)data) |
++ (offset << E1000_MDIC_REG_SHIFT) |
++ (E1000_MDIC_OP_WRITE));
++ break;
++ default:
++ mdic = (((u32)data) |
++ (offset << E1000_MDIC_REG_SHIFT) |
++ (phy->addr << E1000_MDIC_PHY_SHIFT) |
++ (E1000_MDIC_OP_WRITE));
++ break;
++ }
+
+ wr32(E1000_MDIC, mdic);
++ wrfl();
+
+ /* Poll the ready bit to see if the MDI read completed
+ * Increasing the time out as testing showed failures with
+@@ -227,6 +268,18 @@
+ }
+
+ out:
++ switch (hw->mac.type) {
++ /* restore MDICNFG to have phy's addr */
++ case e1000_i210:
++ case e1000_i211:
++ mdicnfg = rd32(E1000_MDICNFG);
++ mdicnfg &= ~(E1000_MDICNFG_PHY_MASK);
++ mdicnfg |= (hw->phy.addr << E1000_MDICNFG_PHY_SHIFT);
++ wr32(E1000_MDICNFG, mdicnfg);
++ break;
++ default:
++ break;
++ }
+ return ret_val;
+ }
+
diff --git a/target/linux/imx6/patches-4.3/203-net-igb-add-phy-read-write-functions-that-accept-phy.patch b/target/linux/imx6/patches-4.3/203-net-igb-add-phy-read-write-functions-that-accept-phy.patch
new file mode 100644
index 0000000..4bb691d
--- /dev/null
+++ b/target/linux/imx6/patches-4.3/203-net-igb-add-phy-read-write-functions-that-accept-phy.patch
@@ -0,0 +1,266 @@
+From 16df7dc5901c1cb2a40f6adbd0d9423768ed8210 Mon Sep 17 00:00:00 2001
+From: Tim Harvey <tharvey at gateworks.com>
+Date: Thu, 15 May 2014 00:29:18 -0700
+Subject: [PATCH] net: igb: add phy read/write functions that accept phy addr
+
+Add igb_write_reg_gs40g/igb_read_reg_gs40g that can be passed a phy address.
+The existing igb_write_phy_reg_gs40g/igb_read_phy_reg_gs40g become wrappers
+to this function.
+
+Signed-off-by: Tim Harvey <tharvey at gateworks.com>
+---
+ drivers/net/ethernet/intel/igb/e1000_82575.c | 4 +-
+ drivers/net/ethernet/intel/igb/e1000_phy.c | 74 +++++++++++++++++++---------
+ drivers/net/ethernet/intel/igb/e1000_phy.h | 6 ++-
+ 3 files changed, 58 insertions(+), 26 deletions(-)
+
+Index: linux-4.3/drivers/net/ethernet/intel/igb/e1000_82575.c
+===================================================================
+--- linux-4.3.orig/drivers/net/ethernet/intel/igb/e1000_82575.c 2015-11-01 16:05:25.000000000 -0800
++++ linux-4.3/drivers/net/ethernet/intel/igb/e1000_82575.c 2015-12-18 10:43:28.000000000 -0800
+@@ -2153,7 +2153,7 @@
+ if (ret_val)
+ goto out;
+
+- ret_val = igb_read_phy_reg_mdic(hw, offset, data);
++ ret_val = igb_read_phy_reg_mdic(hw, hw->phy.addr, offset, data);
+
+ hw->phy.ops.release(hw);
+
+@@ -2178,7 +2178,7 @@
+ if (ret_val)
+ goto out;
+
+- ret_val = igb_write_phy_reg_mdic(hw, offset, data);
++ ret_val = igb_write_phy_reg_mdic(hw, hw->phy.addr, offset, data);
+
+ hw->phy.ops.release(hw);
+
+Index: linux-4.3/drivers/net/ethernet/intel/igb/e1000_phy.c
+===================================================================
+--- linux-4.3.orig/drivers/net/ethernet/intel/igb/e1000_phy.c 2015-12-18 10:39:44.931158318 -0800
++++ linux-4.3/drivers/net/ethernet/intel/igb/e1000_phy.c 2015-12-18 10:39:44.939158318 -0800
+@@ -126,9 +126,8 @@
+ * Reads the MDI control regsiter in the PHY at offset and stores the
+ * information read to data.
+ **/
+-s32 igb_read_phy_reg_mdic(struct e1000_hw *hw, u32 offset, u16 *data)
++s32 igb_read_phy_reg_mdic(struct e1000_hw *hw, u8 addr, u32 offset, u16 *data)
+ {
+- struct e1000_phy_info *phy = &hw->phy;
+ u32 i, mdicnfg, mdic = 0;
+ s32 ret_val = 0;
+
+@@ -147,14 +146,14 @@
+ case e1000_i211:
+ mdicnfg = rd32(E1000_MDICNFG);
+ mdicnfg &= ~(E1000_MDICNFG_PHY_MASK);
+- mdicnfg |= (phy->addr << E1000_MDICNFG_PHY_SHIFT);
++ mdicnfg |= (addr << E1000_MDICNFG_PHY_SHIFT);
+ wr32(E1000_MDICNFG, mdicnfg);
+ mdic = ((offset << E1000_MDIC_REG_SHIFT) |
+ (E1000_MDIC_OP_READ));
+ break;
+ default:
+ mdic = ((offset << E1000_MDIC_REG_SHIFT) |
+- (phy->addr << E1000_MDIC_PHY_SHIFT) |
++ (addr << E1000_MDIC_PHY_SHIFT) |
+ (E1000_MDIC_OP_READ));
+ break;
+ }
+@@ -208,9 +207,8 @@
+ *
+ * Writes data to MDI control register in the PHY at offset.
+ **/
+-s32 igb_write_phy_reg_mdic(struct e1000_hw *hw, u32 offset, u16 data)
++s32 igb_write_phy_reg_mdic(struct e1000_hw *hw, u8 addr, u32 offset, u16 data)
+ {
+- struct e1000_phy_info *phy = &hw->phy;
+ u32 i, mdicnfg, mdic = 0;
+ s32 ret_val = 0;
+
+@@ -229,7 +227,7 @@
+ case e1000_i211:
+ mdicnfg = rd32(E1000_MDICNFG);
+ mdicnfg &= ~(E1000_MDICNFG_PHY_MASK);
+- mdicnfg |= (phy->addr << E1000_MDICNFG_PHY_SHIFT);
++ mdicnfg |= (addr << E1000_MDICNFG_PHY_SHIFT);
+ wr32(E1000_MDICNFG, mdicnfg);
+ mdic = (((u32)data) |
+ (offset << E1000_MDIC_REG_SHIFT) |
+@@ -238,7 +236,7 @@
+ default:
+ mdic = (((u32)data) |
+ (offset << E1000_MDIC_REG_SHIFT) |
+- (phy->addr << E1000_MDIC_PHY_SHIFT) |
++ (addr << E1000_MDIC_PHY_SHIFT) |
+ (E1000_MDIC_OP_WRITE));
+ break;
+ }
+@@ -458,7 +456,7 @@
+ goto out;
+
+ if (offset > MAX_PHY_MULTI_PAGE_REG) {
+- ret_val = igb_write_phy_reg_mdic(hw,
++ ret_val = igb_write_phy_reg_mdic(hw, hw->phy.addr,
+ IGP01E1000_PHY_PAGE_SELECT,
+ (u16)offset);
+ if (ret_val) {
+@@ -467,8 +465,8 @@
+ }
+ }
+
+- ret_val = igb_read_phy_reg_mdic(hw, MAX_PHY_REG_ADDRESS & offset,
+- data);
++ ret_val = igb_read_phy_reg_mdic(hw, hw->phy.addr,
++ MAX_PHY_REG_ADDRESS & offset, data);
+
+ hw->phy.ops.release(hw);
+
+@@ -497,7 +495,7 @@
+ goto out;
+
+ if (offset > MAX_PHY_MULTI_PAGE_REG) {
+- ret_val = igb_write_phy_reg_mdic(hw,
++ ret_val = igb_write_phy_reg_mdic(hw, hw->phy.addr,
+ IGP01E1000_PHY_PAGE_SELECT,
+ (u16)offset);
+ if (ret_val) {
+@@ -506,8 +504,8 @@
+ }
+ }
+
+- ret_val = igb_write_phy_reg_mdic(hw, MAX_PHY_REG_ADDRESS & offset,
+- data);
++ ret_val = igb_write_phy_reg_mdic(hw, hw->phy.addr,
++ MAX_PHY_REG_ADDRESS & offset, data);
+
+ hw->phy.ops.release(hw);
+
+@@ -2547,8 +2545,9 @@
+ }
+
+ /**
+- * igb_write_phy_reg_gs40g - Write GS40G PHY register
++ * igb_write_reg_gs40g - Write GS40G PHY register
+ * @hw: pointer to the HW structure
++ * @addr: phy address to write to
+ * @offset: lower half is register offset to write to
+ * upper half is page to use.
+ * @data: data to write at register offset
+@@ -2556,7 +2555,7 @@
+ * Acquires semaphore, if necessary, then writes the data to PHY register
+ * at the offset. Release any acquired semaphores before exiting.
+ **/
+-s32 igb_write_phy_reg_gs40g(struct e1000_hw *hw, u32 offset, u16 data)
++s32 igb_write_reg_gs40g(struct e1000_hw *hw, u8 addr, u32 offset, u16 data)
+ {
+ s32 ret_val;
+ u16 page = offset >> GS40G_PAGE_SHIFT;
+@@ -2566,10 +2565,10 @@
+ if (ret_val)
+ return ret_val;
+
+- ret_val = igb_write_phy_reg_mdic(hw, GS40G_PAGE_SELECT, page);
++ ret_val = igb_write_phy_reg_mdic(hw, addr, GS40G_PAGE_SELECT, page);
+ if (ret_val)
+ goto release;
+- ret_val = igb_write_phy_reg_mdic(hw, offset, data);
++ ret_val = igb_write_phy_reg_mdic(hw, addr, offset, data);
+
+ release:
+ hw->phy.ops.release(hw);
+@@ -2577,8 +2576,24 @@
+ }
+
+ /**
+- * igb_read_phy_reg_gs40g - Read GS40G PHY register
++ * igb_write_phy_reg_gs40g - Write GS40G PHY register
++ * @hw: pointer to the HW structure
++ * @offset: lower half is register offset to write to
++ * upper half is page to use.
++ * @data: data to write at register offset
++ *
++ * Acquires semaphore, if necessary, then writes the data to PHY register
++ * at the offset. Release any acquired semaphores before exiting.
++ **/
++s32 igb_write_phy_reg_gs40g(struct e1000_hw *hw, u32 offset, u16 data)
++{
++ return igb_write_reg_gs40g(hw, hw->phy.addr, offset, data);
++}
++
++/**
++ * igb_read_reg_gs40g - Read GS40G PHY register
+ * @hw: pointer to the HW structure
++ * @addr: phy address to read from
+ * @offset: lower half is register offset to read to
+ * upper half is page to use.
+ * @data: data to read at register offset
+@@ -2586,7 +2601,7 @@
+ * Acquires semaphore, if necessary, then reads the data in the PHY register
+ * at the offset. Release any acquired semaphores before exiting.
+ **/
+-s32 igb_read_phy_reg_gs40g(struct e1000_hw *hw, u32 offset, u16 *data)
++s32 igb_read_reg_gs40g(struct e1000_hw *hw, u8 addr, u32 offset, u16 *data)
+ {
+ s32 ret_val;
+ u16 page = offset >> GS40G_PAGE_SHIFT;
+@@ -2596,10 +2611,10 @@
+ if (ret_val)
+ return ret_val;
+
+- ret_val = igb_write_phy_reg_mdic(hw, GS40G_PAGE_SELECT, page);
++ ret_val = igb_write_phy_reg_mdic(hw, addr, GS40G_PAGE_SELECT, page);
+ if (ret_val)
+ goto release;
+- ret_val = igb_read_phy_reg_mdic(hw, offset, data);
++ ret_val = igb_read_phy_reg_mdic(hw, addr, offset, data);
+
+ release:
+ hw->phy.ops.release(hw);
+@@ -2607,6 +2622,21 @@
+ }
+
+ /**
++ * igb_read_phy_reg_gs40g - Read GS40G PHY register
++ * @hw: pointer to the HW structure
++ * @offset: lower half is register offset to read to
++ * upper half is page to use.
++ * @data: data to read at register offset
++ *
++ * Acquires semaphore, if necessary, then reads the data in the PHY register
++ * at the offset. Release any acquired semaphores before exiting.
++ **/
++s32 igb_read_phy_reg_gs40g(struct e1000_hw *hw, u32 offset, u16 *data)
++{
++ return igb_read_reg_gs40g(hw, hw->phy.addr, offset, data);
++}
++
++/**
+ * igb_set_master_slave_mode - Setup PHY for Master/slave mode
+ * @hw: pointer to the HW structure
+ *
+Index: linux-4.3/drivers/net/ethernet/intel/igb/e1000_phy.h
+===================================================================
+--- linux-4.3.orig/drivers/net/ethernet/intel/igb/e1000_phy.h 2015-11-01 16:05:25.000000000 -0800
++++ linux-4.3/drivers/net/ethernet/intel/igb/e1000_phy.h 2015-12-18 10:39:44.939158318 -0800
+@@ -62,8 +62,8 @@
+ void igb_power_down_phy_copper(struct e1000_hw *hw);
+ s32 igb_phy_init_script_igp3(struct e1000_hw *hw);
+ s32 igb_initialize_M88E1512_phy(struct e1000_hw *hw);
+-s32 igb_read_phy_reg_mdic(struct e1000_hw *hw, u32 offset, u16 *data);
+-s32 igb_write_phy_reg_mdic(struct e1000_hw *hw, u32 offset, u16 data);
++s32 igb_read_phy_reg_mdic(struct e1000_hw *hw, u8 addr, u32 offset, u16 *data);
++s32 igb_write_phy_reg_mdic(struct e1000_hw *hw, u8 addr, u32 offset, u16 data);
+ s32 igb_read_phy_reg_i2c(struct e1000_hw *hw, u32 offset, u16 *data);
+ s32 igb_write_phy_reg_i2c(struct e1000_hw *hw, u32 offset, u16 data);
+ s32 igb_read_sfp_data_byte(struct e1000_hw *hw, u16 offset, u8 *data);
+@@ -73,6 +73,8 @@
+ s32 igb_get_cable_length_82580(struct e1000_hw *hw);
+ s32 igb_read_phy_reg_gs40g(struct e1000_hw *hw, u32 offset, u16 *data);
+ s32 igb_write_phy_reg_gs40g(struct e1000_hw *hw, u32 offset, u16 data);
++s32 igb_read_reg_gs40g(struct e1000_hw *hw, u8 addr, u32 offset, u16 *data);
++s32 igb_write_reg_gs40g(struct e1000_hw *hw, u8 addr, u32 offset, u16 data);
+ s32 igb_check_polarity_m88(struct e1000_hw *hw);
+
+ /* IGP01E1000 Specific Registers */
diff --git a/target/linux/imx6/patches-4.3/204-net-igb-register-mii_bus-for-SerDes-w-external-phy.patch b/target/linux/imx6/patches-4.3/204-net-igb-register-mii_bus-for-SerDes-w-external-phy.patch
new file mode 100644
index 0000000..4bee4ac
--- /dev/null
+++ b/target/linux/imx6/patches-4.3/204-net-igb-register-mii_bus-for-SerDes-w-external-phy.patch
@@ -0,0 +1,314 @@
+From 03855caf93f7332a3f320228ba1a0e7baae8a749 Mon Sep 17 00:00:00 2001
+From: Tim Harvey <tharvey at gateworks.com>
+Date: Thu, 15 May 2014 12:36:23 -0700
+Subject: [PATCH] net: igb: register mii_bus for SerDes w/ external phy
+
+If an i210 is configured for 1000BASE-BX link_mode and has an external phy
+specified, then register an mii bus using the external phy address as
+a mask.
+
+An i210 hooked to an external standard phy will be configured with a link_mo
+of SGMII in which case phy ops will be configured and used internall in the
+igb driver for link status. However, in certain cases one might be using a
+backplane SerDes connection to something that talks on the mdio bus but is
+not a standard phy, such as a switch. In this case by registering an mdio
+bus a phy driver can manage the device.
+
+Signed-off-by: Tim Harvey <tharvey at gateworks.com>
+---
+ drivers/net/ethernet/intel/igb/e1000_82575.c | 15 +++
+ drivers/net/ethernet/intel/igb/e1000_hw.h | 7 ++
+ drivers/net/ethernet/intel/igb/igb_main.c | 168 ++++++++++++++++++++++++++-
+ 3 files changed, 185 insertions(+), 5 deletions(-)
+
+Index: linux-4.3/drivers/net/ethernet/intel/igb/e1000_82575.c
+===================================================================
+--- linux-4.3.orig/drivers/net/ethernet/intel/igb/e1000_82575.c 2015-12-18 10:39:44.935158318 -0800
++++ linux-4.3/drivers/net/ethernet/intel/igb/e1000_82575.c 2015-12-18 10:39:44.943158318 -0800
+@@ -612,13 +612,25 @@
+ switch (link_mode) {
+ case E1000_CTRL_EXT_LINK_MODE_1000BASE_KX:
+ hw->phy.media_type = e1000_media_type_internal_serdes;
++ if (igb_sgmii_uses_mdio_82575(hw)) {
++ u32 mdicnfg = rd32(E1000_MDICNFG);
++ mdicnfg &= E1000_MDICNFG_PHY_MASK;
++ hw->phy.addr = mdicnfg >> E1000_MDICNFG_PHY_SHIFT;
++ hw_dbg("1000BASE_KX w/ external MDIO device at 0x%x\n",
++ hw->phy.addr);
++ } else {
++ hw_dbg("1000BASE_KX");
++ }
+ break;
+ case E1000_CTRL_EXT_LINK_MODE_SGMII:
+ /* Get phy control interface type set (MDIO vs. I2C)*/
+ if (igb_sgmii_uses_mdio_82575(hw)) {
+ hw->phy.media_type = e1000_media_type_copper;
+ dev_spec->sgmii_active = true;
++ hw_dbg("SGMII with external MDIO PHY");
+ break;
++ } else {
++ hw_dbg("SGMII with external I2C PHY");
+ }
+ /* fall through for I2C based SGMII */
+ case E1000_CTRL_EXT_LINK_MODE_PCIE_SERDES:
+@@ -635,8 +647,11 @@
+ hw->phy.media_type = e1000_media_type_copper;
+ dev_spec->sgmii_active = true;
+ }
++ hw_dbg("SERDES with external SFP");
+
+ break;
++ } else {
++ hw_dbg("SERDES");
+ }
+
+ /* do not change link mode for 100BaseFX */
+Index: linux-4.3/drivers/net/ethernet/intel/igb/e1000_hw.h
+===================================================================
+--- linux-4.3.orig/drivers/net/ethernet/intel/igb/e1000_hw.h 2015-11-01 16:05:25.000000000 -0800
++++ linux-4.3/drivers/net/ethernet/intel/igb/e1000_hw.h 2015-12-18 10:39:44.943158318 -0800
+@@ -27,6 +27,7 @@
+ #include <linux/delay.h>
+ #include <linux/io.h>
+ #include <linux/netdevice.h>
++#include <linux/phy.h>
+
+ #include "e1000_regs.h"
+ #include "e1000_defines.h"
+@@ -543,6 +544,12 @@
+ struct e1000_mbx_info mbx;
+ struct e1000_host_mng_dhcp_cookie mng_cookie;
+
++#ifdef CONFIG_PHYLIB
++ /* Phylib and MDIO interface */
++ struct mii_bus *mii_bus;
++ struct phy_device *phy_dev;
++ phy_interface_t phy_interface;
++#endif
+ union {
+ struct e1000_dev_spec_82575 _82575;
+ } dev_spec;
+Index: linux-4.3/drivers/net/ethernet/intel/igb/igb_main.c
+===================================================================
+--- linux-4.3.orig/drivers/net/ethernet/intel/igb/igb_main.c 2015-12-18 10:39:44.407158315 -0800
++++ linux-4.3/drivers/net/ethernet/intel/igb/igb_main.c 2015-12-18 10:39:44.943158318 -0800
+@@ -41,6 +41,7 @@
+ #include <linux/if_vlan.h>
+ #include <linux/pci.h>
+ #include <linux/pci-aspm.h>
++#include <linux/phy.h>
+ #include <linux/delay.h>
+ #include <linux/interrupt.h>
+ #include <linux/ip.h>
+@@ -2223,6 +2224,126 @@
+ return status;
+ }
+
++
++#ifdef CONFIG_PHYLIB
++/*
++ * MMIO/PHYdev support
++ */
++
++static int igb_enet_mdio_read(struct mii_bus *bus, int mii_id, int regnum)
++{
++ struct e1000_hw *hw = bus->priv;
++ u16 out;
++ int err;
++
++ err = igb_read_reg_gs40g(hw, mii_id, regnum, &out);
++ if (err)
++ return err;
++ return out;
++}
++
++static int igb_enet_mdio_write(struct mii_bus *bus, int mii_id, int regnum,
++ u16 val)
++{
++ struct e1000_hw *hw = bus->priv;
++
++ return igb_write_reg_gs40g(hw, mii_id, regnum, val);
++}
++
++static int igb_enet_mdio_reset(struct mii_bus *bus)
++{
++ udelay(300);
++ return 0;
++}
++
++static void igb_enet_mii_link(struct net_device *netdev)
++{
++}
++
++/* Probe the mdio bus for phys and connect them */
++static int igb_enet_mii_probe(struct net_device *netdev)
++{
++ struct igb_adapter *adapter = netdev_priv(netdev);
++ struct e1000_hw *hw = &adapter->hw;
++ struct phy_device *phy_dev = NULL;
++ int phy_id;
++
++ /* check for attached phy */
++ for (phy_id = 0; (phy_id < PHY_MAX_ADDR); phy_id++) {
++ if (hw->mii_bus->phy_map[phy_id]) {
++ phy_dev = hw->mii_bus->phy_map[phy_id];
++ break;
++ }
++ }
++ if (!phy_dev) {
++ netdev_err(netdev, "no PHY found\n");
++ return -ENODEV;
++ }
++
++ hw->phy_interface = PHY_INTERFACE_MODE_RGMII;
++ phy_dev = phy_connect(netdev, dev_name(&phy_dev->dev),
++ igb_enet_mii_link, hw->phy_interface);
++ if (IS_ERR(phy_dev)) {
++ netdev_err(netdev, "could not attach to PHY\n");
++ return PTR_ERR(phy_dev);
++ }
++
++ hw->phy_dev = phy_dev;
++ netdev_info(netdev, "igb PHY driver [%s] (mii_bus:phy_addr=%s)\n",
++ hw->phy_dev->drv->name, dev_name(&hw->phy_dev->dev));
++
++ return 0;
++}
++
++/* Create and register mdio bus */
++static int igb_enet_mii_init(struct pci_dev *pdev)
++{
++ struct mii_bus *mii_bus;
++ struct net_device *netdev = pci_get_drvdata(pdev);
++ struct igb_adapter *adapter = netdev_priv(netdev);
++ struct e1000_hw *hw = &adapter->hw;
++ int err;
++
++ mii_bus = mdiobus_alloc();
++ if (mii_bus == NULL) {
++ err = -ENOMEM;
++ goto err_out;
++ }
++
++ mii_bus->name = "igb_enet_mii_bus";
++ mii_bus->read = igb_enet_mdio_read;
++ mii_bus->write = igb_enet_mdio_write;
++ mii_bus->reset = igb_enet_mdio_reset;
++ snprintf(mii_bus->id, MII_BUS_ID_SIZE, "%s-%x",
++ pci_name(pdev), hw->device_id + 1);
++ mii_bus->priv = hw;
++ mii_bus->parent = &pdev->dev;
++ mii_bus->phy_mask = ~(1 << hw->phy.addr);
++
++ err = mdiobus_register(mii_bus);
++ if (err) {
++ printk(KERN_ERR "failed to register mii_bus: %d\n", err);
++ goto err_out_free_mdiobus;
++ }
++ hw->mii_bus = mii_bus;
++
++ return 0;
++
++err_out_free_mdiobus:
++ mdiobus_free(mii_bus);
++err_out:
++ return err;
++}
++
++static void igb_enet_mii_remove(struct e1000_hw *hw)
++{
++ if (hw->mii_bus) {
++ mdiobus_unregister(hw->mii_bus);
++ mdiobus_free(hw->mii_bus);
++ }
++}
++#endif /* CONFIG_PHYLIB */
++
+ /**
+ * igb_probe - Device Initialization Routine
+ * @pdev: PCI device information struct
+@@ -2645,6 +2766,13 @@
+ }
+ }
+ pm_runtime_put_noidle(&pdev->dev);
++
++#ifdef CONFIG_PHYLIB
++ /* create and register the mdio bus if using ext phy */
++ if (rd32(E1000_MDICNFG) & E1000_MDICNFG_EXT_MDIO)
++ igb_enet_mii_init(pdev);
++#endif
++
+ return 0;
+
+ err_register:
+@@ -2792,6 +2920,10 @@
+ struct e1000_hw *hw = &adapter->hw;
+
+ pm_runtime_get_noresume(&pdev->dev);
++#ifdef CONFIG_PHYLIB
++ if (rd32(E1000_MDICNFG) & E1000_MDICNFG_EXT_MDIO)
++ igb_enet_mii_remove(hw);
++#endif
+ #ifdef CONFIG_IGB_HWMON
+ igb_sysfs_exit(adapter);
+ #endif
+@@ -3105,6 +3237,12 @@
+ if (!resuming)
+ pm_runtime_put(&pdev->dev);
+
++#ifdef CONFIG_PHYLIB
++ /* Probe and connect to PHY if using ext phy */
++ if (rd32(E1000_MDICNFG) & E1000_MDICNFG_EXT_MDIO)
++ igb_enet_mii_probe(netdev);
++#endif
++
+ /* start the watchdog. */
+ hw->mac.get_link_status = 1;
+ schedule_work(&adapter->watchdog_task);
+@@ -7090,21 +7228,41 @@
+ static int igb_mii_ioctl(struct net_device *netdev, struct ifreq *ifr, int cmd)
+ {
+ struct igb_adapter *adapter = netdev_priv(netdev);
++ struct e1000_hw *hw = &adapter->hw;
+ struct mii_ioctl_data *data = if_mii(ifr);
+
+- if (adapter->hw.phy.media_type != e1000_media_type_copper)
++ if (adapter->hw.phy.media_type != e1000_media_type_copper &&
++ !(rd32(E1000_MDICNFG) & E1000_MDICNFG_EXT_MDIO))
+ return -EOPNOTSUPP;
+
+ switch (cmd) {
+ case SIOCGMIIPHY:
+- data->phy_id = adapter->hw.phy.addr;
++ data->phy_id = hw->phy.addr;
+ break;
+ case SIOCGMIIREG:
+- if (igb_read_phy_reg(&adapter->hw, data->reg_num & 0x1F,
+- &data->val_out))
+- return -EIO;
++ if (hw->mac.type == e1000_i210 || hw->mac.type == e1000_i211) {
++ if (igb_read_reg_gs40g(&adapter->hw, data->phy_id,
++ data->reg_num & 0x1F,
++ &data->val_out))
++ return -EIO;
++ } else {
++ if (igb_read_phy_reg(&adapter->hw, data->reg_num & 0x1F,
++ &data->val_out))
++ return -EIO;
++ }
+ break;
+ case SIOCSMIIREG:
++ if (hw->mac.type == e1000_i210 || hw->mac.type == e1000_i211) {
++ if (igb_write_reg_gs40g(hw, data->phy_id,
++ data->reg_num & 0x1F,
++ data->val_in))
++ return -EIO;
++ } else {
++ if (igb_write_phy_reg(hw, data->reg_num & 0x1F,
++ data->val_in))
++ return -EIO;
++ }
++ break;
+ default:
+ return -EOPNOTSUPP;
+ }
diff --git a/target/linux/imx6/patches-4.3/205-phy-add-driver-for-GW16083-Ethernet-Expansion-Mezzan.patch b/target/linux/imx6/patches-4.3/205-phy-add-driver-for-GW16083-Ethernet-Expansion-Mezzan.patch
new file mode 100644
index 0000000..a2ca325
--- /dev/null
+++ b/target/linux/imx6/patches-4.3/205-phy-add-driver-for-GW16083-Ethernet-Expansion-Mezzan.patch
@@ -0,0 +1,31 @@
+Index: linux-4.3/drivers/net/phy/Kconfig
+===================================================================
+--- linux-4.3.orig/drivers/net/phy/Kconfig 2015-12-18 10:39:44.371158315 -0800
++++ linux-4.3/drivers/net/phy/Kconfig 2015-12-18 10:39:44.951158318 -0800
+@@ -309,6 +309,14 @@
+
+ source "drivers/net/phy/b53/Kconfig"
+
++config GATEWORKS_GW16083
++ tristate "Gateworks GW16083 Ethernet Expansion Mezzanine"
++ ---help---
++ The Gateworks GW16083 Ethernet Expansion Mezzanine connects to a
++ Gateworks Ventana baseboard and provides a 7-port GbE managed
++ Ethernet switch with 4 dedicated GbE RJ45 ports, and 2 Gbe/SFP
++ ports"
++
+ endif # PHYLIB
+
+ config MICREL_KS8995MA
+Index: linux-4.3/drivers/net/phy/Makefile
+===================================================================
+--- linux-4.3.orig/drivers/net/phy/Makefile 2015-12-18 10:39:44.371158315 -0800
++++ linux-4.3/drivers/net/phy/Makefile 2015-12-18 10:39:44.951158318 -0800
+@@ -44,6 +44,7 @@
+ obj-$(CONFIG_DP83867_PHY) += dp83867.o
+ obj-$(CONFIG_STE10XP) += ste10Xp.o
+ obj-$(CONFIG_MICREL_PHY) += micrel.o
++obj-$(CONFIG_GATEWORKS_GW16083) += gw16083.o
+ obj-$(CONFIG_MDIO_OCTEON) += mdio-octeon.o
+ obj-$(CONFIG_MICREL_KS8995MA) += spi_ks8995.o
+ obj-$(CONFIG_AT803X_PHY) += at803x.o
diff --git a/target/linux/imx6/patches-4.3/206-ARM-imx-ventana-added-GW16083-to-device-tree.patch b/target/linux/imx6/patches-4.3/206-ARM-imx-ventana-added-GW16083-to-device-tree.patch
new file mode 100644
index 0000000..81fbe0e
--- /dev/null
+++ b/target/linux/imx6/patches-4.3/206-ARM-imx-ventana-added-GW16083-to-device-tree.patch
@@ -0,0 +1,64 @@
+Index: linux-4.3/arch/arm/boot/dts/imx6qdl-gw51xx.dtsi
+===================================================================
+--- linux-4.3.orig/arch/arm/boot/dts/imx6qdl-gw51xx.dtsi 2015-12-18 10:39:44.895158318 -0800
++++ linux-4.3/arch/arm/boot/dts/imx6qdl-gw51xx.dtsi 2015-12-18 10:43:21.000000000 -0800
+@@ -158,6 +158,11 @@
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_i2c2>;
+ status = "okay";
++
++ gw16083: gw16083 at 52 {
++ compatible = "gateworks,gw16083";
++ reg = <0x52>;
++ };
+ };
+
+ &i2c3 {
+Index: linux-4.3/arch/arm/boot/dts/imx6qdl-gw52xx.dtsi
+===================================================================
+--- linux-4.3.orig/arch/arm/boot/dts/imx6qdl-gw52xx.dtsi 2015-12-18 10:39:44.907158318 -0800
++++ linux-4.3/arch/arm/boot/dts/imx6qdl-gw52xx.dtsi 2015-12-18 10:43:21.000000000 -0800
+@@ -233,6 +233,11 @@
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_i2c2>;
+ status = "okay";
++
++ gw16083: gw16083 at 52 {
++ compatible = "gateworks,gw16083";
++ reg = <0x52>;
++ };
+ };
+
+ &i2c3 {
+Index: linux-4.3/arch/arm/boot/dts/imx6qdl-gw53xx.dtsi
+===================================================================
+--- linux-4.3.orig/arch/arm/boot/dts/imx6qdl-gw53xx.dtsi 2015-12-18 10:39:44.899158318 -0800
++++ linux-4.3/arch/arm/boot/dts/imx6qdl-gw53xx.dtsi 2015-12-18 10:43:25.000000000 -0800
+@@ -226,6 +226,11 @@
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_i2c2>;
+ status = "okay";
++
++ gw16083: gw16083 at 52 {
++ compatible = "gateworks,gw16083";
++ reg = <0x52>;
++ };
+ };
+
+ &i2c3 {
+Index: linux-4.3/arch/arm/boot/dts/imx6qdl-gw54xx.dtsi
+===================================================================
+--- linux-4.3.orig/arch/arm/boot/dts/imx6qdl-gw54xx.dtsi 2015-12-18 10:39:44.899158318 -0800
++++ linux-4.3/arch/arm/boot/dts/imx6qdl-gw54xx.dtsi 2015-12-18 10:43:25.000000000 -0800
+@@ -317,6 +317,11 @@
+ };
+ };
+ };
++
++ gw16083: gw16083 at 52 {
++ compatible = "gateworks,gw16083";
++ reg = <0x52>;
++ };
+ };
+
+ &i2c3 {
--
2.6.4
_______________________________________________
openwrt-devel mailing list
openwrt-devel at lists.openwrt.org
https://lists.openwrt.org/cgi-bin/mailman/listinfo/openwrt-devel
More information about the openwrt-devel
mailing list