[OpenWrt-Devel] [PATCH v5] Add support for Ubiquiti EdgeRouter X (UBNT-ERX)
Nikolay Martynov
mar.kolya at gmail.com
Wed Dec 9 10:34:31 EST 2015
Hi.
I know you guys a probably very busy, but could you please confirm
that this is the right list to submit such patches and format of this
patch is correct - so I could fix it if it's not.
Thanks!
2015-12-03 2:16 GMT-05:00 Nikolay Martynov <mar.kolya at gmail.com>:
> This router is based on MT7621 SoC, no wifi, nand.
>
> Works:
> * Boots.
> * Ethernet.
> * Switch.
> * Button (reset).
> * Flashing OpenWrt from stock firmware.
> * Upgrading OpenWrt.
>
> Doesn't work:
> * No GPIO leds. All leds are controlled by switch,
> but stock firmware was able to control them.
> * SoC has crypto engine but no open driver.
> * SoC has nat acceleration, but no open driver.
> * This router has 2MB spi flash soldered in but MT
> nand/spi drivers do not support pin sharing,
> so it is not accessable and disabled. Stock
> firmware could read it and it was empty.
>
> Unknown status: PoE support.
>
> Router has serial pins populated. If looking at the top
> of the router, then counting from Eth sockets pins go as:
> 'GND, RX, TX, GND'. 3.3v, 57600.
>
> U-boot bootloader supports tftpboot, controlled from serial.
> This router has two kernel partitions: 'live' and 'backup'.
> They are swapped during flashing (on both stock and OpenWrt).
> Active partition is controlled by a flag in factory partition.
> U-boot has cusotm command to switch active kernel partition.
> Kernel partitions are 'bare flash' 3MB. Stock bootloader has
> no UBI support. Stock rootfs is UBIFS.
>
> Flashing procedure.
> Stock firmware uses custom kernel patch to mount squashfs
> from a file that is located on UBIFS volume. This makes wiping
> out this volume from within stock firmware difficult.
> Instead this patch builds image that is flashable by stock firmware
> and contains initrams image (with minimal set of packages
> to fit into kernel partition). Once this is flashed one can reboot
> into initramfs OpenWrt and use sysupgrade to flash OpenWrt including
> rootfs into nand.
> Note: factory image is only built if initramfs image is enabled.
>
> v2: Fix building all mt7621 targets along with ubnt-erx.
> v3: Undo change to MT7621 nand partitions, make nand detection
> less likely to affect other nands.
> v4: Update as per Piotr Dymacz comments.
> v5: Fix upgrading code to actually upgrade kernel.
>
> Signed-off-by: Nikolay Martynov <mar.kolya at gmail.com>
> ---
> package/system/procd/files/nand.sh | 4 +
> .../linux/ramips/base-files/etc/board.d/02_network | 1 +
> target/linux/ramips/base-files/lib/ramips.sh | 5 +-
> .../ramips/base-files/lib/upgrade/platform.sh | 24 +++++
> target/linux/ramips/base-files/lib/upgrade/ubnt.sh | 71 +++++++++++++
> target/linux/ramips/dts/MT7621.dts | 22 ++++
> target/linux/ramips/dts/UBNT-ERX.dts | 117 +++++++++++++++++++++
> target/linux/ramips/dts/mt7621.dtsi | 20 ----
> target/linux/ramips/image/Makefile | 61 ++++++++++-
> target/linux/ramips/mt7621/profiles/ubnt.mk | 17 +++
> .../patches-3.18/0901-spansion_nand_id_fix.patch | 43 ++++++++
> 11 files changed, 363 insertions(+), 22 deletions(-)
> create mode 100644 target/linux/ramips/base-files/lib/upgrade/ubnt.sh
> create mode 100644 target/linux/ramips/dts/UBNT-ERX.dts
> create mode 100644 target/linux/ramips/mt7621/profiles/ubnt.mk
> create mode 100644 target/linux/ramips/patches-3.18/0901-spansion_nand_id_fix.patch
>
> diff --git a/package/system/procd/files/nand.sh b/package/system/procd/files/nand.sh
> index 0c179cb..67867da 100644
> --- a/package/system/procd/files/nand.sh
> +++ b/package/system/procd/files/nand.sh
> @@ -275,6 +275,10 @@ nand_upgrade_tar() {
> nand_do_upgrade_stage2() {
> local file_type=$(identify $1)
>
> + if type 'platform_nand_pre_upgrade' >/dev/null 2>/dev/null; then
> + platform_nand_pre_upgrade "$1"
> + fi
> +
> [ ! "$(find_mtd_index "$CI_UBIPART")" ] && CI_UBIPART="rootfs"
>
> case "$file_type" in
> diff --git a/target/linux/ramips/base-files/etc/board.d/02_network b/target/linux/ramips/base-files/etc/board.d/02_network
> index 7e51229..de81553 100755
> --- a/target/linux/ramips/base-files/etc/board.d/02_network
> +++ b/target/linux/ramips/base-files/etc/board.d/02_network
> @@ -122,6 +122,7 @@ ramips_setup_interfaces()
> f5d8235-v2|\
> hg255d|\
> rt-n14u|\
> + ubnt-erx|\
> ur-326n4g|\
> wrtnode|\
> wt3020|\
> diff --git a/target/linux/ramips/base-files/lib/ramips.sh b/target/linux/ramips/base-files/lib/ramips.sh
> index 92e13c0..ba23939 100755
> --- a/target/linux/ramips/base-files/lib/ramips.sh
> +++ b/target/linux/ramips/base-files/lib/ramips.sh
> @@ -349,6 +349,9 @@ ramips_board_detect() {
> *"TEW-692GR")
> name="tew-692gr"
> ;;
> + *"UBNT-ERX")
> + name="ubnt-erx"
> + ;;
> *"UR-326N4G")
> name="ur-326n4g"
> ;;
> @@ -396,7 +399,7 @@ ramips_board_detect() {
> ;;
> *"WizFi630A")
> name="wizfi630a"
> - ;;
> + ;;
> *"WL-330N")
> name="wl-330n"
> ;;
> diff --git a/target/linux/ramips/base-files/lib/upgrade/platform.sh b/target/linux/ramips/base-files/lib/upgrade/platform.sh
> index 073593a..b0d624e 100755
> --- a/target/linux/ramips/base-files/lib/upgrade/platform.sh
> +++ b/target/linux/ramips/base-files/lib/upgrade/platform.sh
> @@ -181,12 +181,36 @@ platform_check_image() {
> }
> return 0
> ;;
> + ubnt-erx)
> + nand_do_platform_check "$board" "$1"
> + return $?;
> + ;;
> esac
>
> echo "Sysupgrade is not yet supported on $board."
> return 1
> }
>
> +platform_nand_pre_upgrade() {
> + local board=$(ramips_board_name)
> +
> + case "$board" in
> + ubnt-erx)
> + platform_upgrade_ubnt_erx "$ARGV"
> + ;;
> + esac
> +}
> +
> +platform_pre_upgrade() {
> + local board=$(ramips_board_name)
> +
> + case "$board" in
> + ubnt-erx)
> + nand_do_upgrade "$ARGV"
> + ;;
> + esac
> +}
> +
> platform_do_upgrade() {
> local board=$(ramips_board_name)
>
> diff --git a/target/linux/ramips/base-files/lib/upgrade/ubnt.sh b/target/linux/ramips/base-files/lib/upgrade/ubnt.sh
> new file mode 100644
> index 0000000..0dc602b
> --- /dev/null
> +++ b/target/linux/ramips/base-files/lib/upgrade/ubnt.sh
> @@ -0,0 +1,71 @@
> +#
> +# Copyright (C) 2015 OpenWrt.org
> +#
> +
> +UBNT_ERX_KERNEL_INDEX_OFFSET=160
> +
> +ubnt_get_target_kernel() {
> + local factory_mtd=$1
> + local current_kernel_index=$(dd if=${factory_mtd} bs=1 count=1 skip=$UBNT_ERX_KERNEL_INDEX_OFFSET 2>/dev/null|hexdump -e '/1 "%X "')
> +
> + if [ $current_kernel_index == "0" ]; then
> + echo 'kernel2'
> + elif [ $current_kernel_index == "1" ]; then
> + echo 'kernel1'
> + fi
> +}
> +
> +ubnt_update_target_kernel() {
> + local factory_mtd=$1
> + local kernel_part=$2
> +
> + local new_kernel_index
> + if [ $kernel_part == "kernel1" ]; then
> + new_kernel_index="\x00"
> + elif [ $kernel_part == "kernel2" ]; then
> + new_kernel_index="\x01"
> + else
> + echo 'Unknown kernel image index'
> + exit 1
> + fi
> +
> + if ! (echo -e $new_kernel_index | dd of=${factory_mtd} bs=1 count=1 seek=$UBNT_ERX_KERNEL_INDEX_OFFSET); then
> + echo 'Failed to update kernel bootup index'
> + exit 1
> + fi
> +}
> +
> +platform_upgrade_ubnt_erx() {
> + local factory_mtd=$(find_mtd_part factory)
> + if [ ! -n "$factory_mtd" ]; then
> + echo "cannot find factory partition"
> + exit 1
> + fi
> +
> + local kernel_part="$(ubnt_get_target_kernel ${factory_mtd})"
> + if [ ! -n "$kernel_part" ]; then
> + echo "cannot find factory partition"
> + exit 1
> + fi
> +
> + CI_KERNPART=${kernel_part}
> +
> + #Remove volume possibly left over from stock firmware
> + local ubidev="$( nand_find_ubi "$CI_UBIPART" )"
> + if [ ! "$ubidev" ]; then
> + local mtdnum="$( find_mtd_index "$CI_UBIPART" )"
> + if [ ! "$mtdnum" ]; then
> + echo "cannot find ubi mtd partition $CI_UBIPART"
> + return 1
> + fi
> + ubiattach -m "$mtdnum"
> + sync
> + ubidev="$( nand_find_ubi "$CI_UBIPART" )"
> + fi
> + if [ -n "$ubidev" ]; then
> + local troot_ubivol="$( nand_find_volume $ubidev troot )"
> + [ "$troot_ubivol" ] && ubirmvol /dev/$ubidev -N troot || true
> + fi
> +
> + ubnt_update_target_kernel ${factory_mtd} ${kernel_part}
> +}
> diff --git a/target/linux/ramips/dts/MT7621.dts b/target/linux/ramips/dts/MT7621.dts
> index c90fc95..96f3416 100644
> --- a/target/linux/ramips/dts/MT7621.dts
> +++ b/target/linux/ramips/dts/MT7621.dts
> @@ -31,4 +31,26 @@
> };
> };
> };
> +
> + nand at 1e003000 {
> + partition at 0 {
> + label = "uboot";
> + reg = <0x00000 0x80000>; /* 64 KB */
> + };
> +
> + partition at 80000 {
> + label = "uboot_env";
> + reg = <0x80000 0x80000>; /* 64 KB */
> + };
> +
> + partition at 100000 {
> + label = "factory";
> + reg = <0x100000 0x40000>;
> + };
> +
> + partition at 140000 {
> + label = "rootfs";
> + reg = <0x140000 0xec0000>;
> + };
> + };
> };
> diff --git a/target/linux/ramips/dts/UBNT-ERX.dts b/target/linux/ramips/dts/UBNT-ERX.dts
> new file mode 100644
> index 0000000..4aa3be9
> --- /dev/null
> +++ b/target/linux/ramips/dts/UBNT-ERX.dts
> @@ -0,0 +1,117 @@
> +/dts-v1/;
> +
> +/include/ "mt7621.dtsi"
> +
> +/ {
> + compatible = "mediatek,mt7621-eval-board", "mediatek,mt7621-soc";
> + model = "UBNT-ERX";
> +
> + memory at 0 {
> + device_type = "memory";
> + reg = <0x0 0x10000000>;
> + };
> +
> + chosen {
> + bootargs = "console=ttyS0,57600";
> + };
> +
> + palmbus at 1E000000 {
> + spi at b00 {
> + /* This board has 2Mb spi flash soldered in and visible
> + from manufacturer's firmware.
> + But this SoC shares spi and nand pins,
> + and current driver desn't handle this sharing well */
> + status = "disabled";
> + m25p80 at 0 {
> + #address-cells = <1>;
> + #size-cells = <1>;
> + compatible = "m25p80";
> + reg = <1>;
> + linux,modalias = "m25p80";
> + spi-max-frequency = <10000000>;
> +
> + partition at 0 {
> + label = "spi";
> + reg = <0x0 0x200000>;
> + read-only;
> + };
> + };
> + };
> + };
> +
> + nand at 1e003000 {
> + compatible = "mtk,mt7621-nand";
> + bank-width = <2>;
> + reg = <0x1e003000 0x800
> + 0x1e003800 0x800>;
> + #address-cells = <1>;
> + #size-cells = <1>;
> +
> + partition at 0 {
> + label = "u-boot";
> + reg = <0x0 0x80000>;
> + read-only;
> + };
> +
> + partition at 80000 {
> + label = "u-boot-env";
> + reg = <0x80000 0x60000>;
> + read-only;
> + };
> +
> + factory: partition at e0000 {
> + label = "factory";
> + reg = <0xe0000 0x60000>;
> + };
> +
> + partition at 140000 {
> + label = "kernel1";
> + reg = <0x140000 0x300000>;
> + };
> +
> + partition at 440000 {
> + label = "kernel2";
> + reg = <0x440000 0x300000>;
> + };
> +
> + partition at 740000 {
> + label = "ubi";
> + reg = <0x740000 0xf7c0000>;
> + };
> +
> + };
> +
> + ethernet at 1e100000 {
> + mtd-mac-address = <&factory 0x22>;
> + };
> +
> + pinctrl {
> + state_default: pinctrl0 {
> + gpio {
> + ralink,group = "uart2", "uart3", "i2c", "pcie", "rgmii2", "jtag";
> + ralink,function = "gpio";
> + };
> + };
> + };
> +
> + sdhci at 1E130000 {
> + status = "disabled";
> + };
> +
> + pcie at 1e140000 {
> + status = "disabled";
> + };
> +
> + gpio-keys-polled {
> + compatible = "gpio-keys-polled";
> + #address-cells = <1>;
> + #size-cells = <0>;
> + poll-interval = <20>;
> +
> + reset {
> + label = "reset";
> + gpios = <&gpio0 12 1>;
> + linux,code = <0x198>;
> + };
> + };
> +};
> diff --git a/target/linux/ramips/dts/mt7621.dtsi b/target/linux/ramips/dts/mt7621.dtsi
> index fd2e100..c29a040 100644
> --- a/target/linux/ramips/dts/mt7621.dtsi
> +++ b/target/linux/ramips/dts/mt7621.dtsi
> @@ -241,26 +241,6 @@
> 0x1e003800 0x800>;
> #address-cells = <1>;
> #size-cells = <1>;
> -
> - partition at 0 {
> - label = "uboot";
> - reg = <0x00000 0x80000>; /* 64 KB */
> - };
> -
> - partition at 80000 {
> - label = "uboot_env";
> - reg = <0x80000 0x80000>; /* 64 KB */
> - };
> -
> - partition at 100000 {
> - label = "factory";
> - reg = <0x100000 0x40000>;
> - };
> -
> - partition at 140000 {
> - label = "rootfs";
> - reg = <0x140000 0xec0000>;
> - };
> };
>
> ethernet at 1e100000 {
> diff --git a/target/linux/ramips/image/Makefile b/target/linux/ramips/image/Makefile
> index 00a2923..6230688 100644
> --- a/target/linux/ramips/image/Makefile
> +++ b/target/linux/ramips/image/Makefile
> @@ -69,6 +69,51 @@ define Build/relocate-kernel
> mv $@.new $@
> endef
>
> +define Build/ubnt-erx-factory-compat
> + echo '21001:6' > $@.compat
> + $(TAR) -cf $@ --transform='s/^.*/compat/' $@.compat
> + $(RM) $@.compat
> +endef
> +
> +define Build/ubnt-erx-factory-kernel
> + if [ -e $(BIN_DIR)/$(KERNEL_INITRAMFS_IMAGE) ]; then \
> + $(TAR) -rf $@ --transform='s/^.*/vmlinux.tmp/' $(BIN_DIR)/$(KERNEL_INITRAMFS_IMAGE); \
> + \
> + md5sum --binary $(BIN_DIR)/$(KERNEL_INITRAMFS_IMAGE) | awk '{print $$1}'> $@.md5; \
> + $(TAR) -rf $@ --transform='s/^.*/vmlinux.tmp.md5/' $@.md5; \
> + $(RM) $@.md5; \
> + fi
> +endef
> +
> +define Build/ubnt-erx-factory-rootfs
> + echo "dummy" > $@.rootfs
> + $(TAR) -rf $@ --transform='s/^.*/squashfs.tmp/' $@.rootfs
> +
> + md5sum --binary $@.rootfs | awk '{print $$1}'> $@.md5
> + $(TAR) -rf $@ --transform='s/^.*/squashfs.tmp.md5/' $@.md5
> + $(RM) $@.md5
> + $(RM) $@.rootfs
> +endef
> +
> +define Build/ubnt-erx-factory-version
> + echo '$(BOARD) $(VERSION_CODE) $(VERSION_NUMBER)' > $@.version
> + $(TAR) -rf $@ --transform='s/^.*/version.tmp/' $@.version
> + $(RM) $@.version
> +endef
> +
> +#We need kernel+initrams fit into kernel partition
> +define Build/ubnt-erx-factory-check-size
> + @[ $$(($(subst k,* 1024,$(subst m, * 1024k,$(1))))) -ge "$$($(TAR) -xf $@ vmlinux.tmp -O | wc -c)" ] || { \
> + echo "WARNING: Initramfs kernel for image $@ is too big (kernel size: $$($(TAR) -xf $@ vmlinux.tmp -O | wc -c), max size $(1))" >&2; \
> + $(RM) -f $@; \
> + }
> +
> + @[ "$$($(TAR) -xf $@ vmlinux.tmp -O | wc -c)" -gt 0 ] || { \
> + echo "WARNING: Kernel for image $@ not found" >&2; \
> + $(RM) -f $@; \
> + }
> +endef
> +
> define MkCombineduImage
> $(call PatchKernelLzma,$(2),$(3))
> if [ `stat -c%s "$(KDIR)/vmlinux-$(2).bin.lzma"` -gt `expr $(4) - 64` ]; then \
> @@ -954,7 +999,7 @@ endif
> #
>
> ifeq ($(SUBTARGET),mt7621)
> - TARGET_DEVICES += mt7621 wsr-600 wsr-1166 dir-860l-b1 firewrt pbr-m1 re6500 sap-g3200u3 zbt-wg2626 wf-2881
> + TARGET_DEVICES += mt7621 wsr-600 wsr-1166 dir-860l-b1 firewrt pbr-m1 re6500 sap-g3200u3 zbt-wg2626 wf-2881 ubnt-erx
> endif
>
> define Device/mt7621
> @@ -1018,6 +1063,20 @@ define Device/wf-2881
> IMAGE/sysupgrade.bin := append-kernel | pad-to $$(KERNEL_SIZE) | append-ubi | check-size $$$$(IMAGE_SIZE)
> endef
>
> +define Device/ubnt-erx
> + DTS := UBNT-ERX
> + FILESYSTEMS := squashfs
> + KERNEL_SIZE := 3145728
> + KERNEL := $(KERNEL_DTB) | uImage lzma
> + IMAGES := sysupgrade.tar factory-initramfs.tar
> + IMAGE/factory-initramfs.tar := ubnt-erx-factory-compat | \
> + ubnt-erx-factory-kernel | \
> + ubnt-erx-factory-rootfs | \
> + ubnt-erx-factory-version | \
> + ubnt-erx-factory-check-size $$$$(KERNEL_SIZE)
> + IMAGE/sysupgrade.tar := sysupgrade-nand
> +endef
> +
> #
> # MT7628 Profiles
> #
> diff --git a/target/linux/ramips/mt7621/profiles/ubnt.mk b/target/linux/ramips/mt7621/profiles/ubnt.mk
> new file mode 100644
> index 0000000..67efa60
> --- /dev/null
> +++ b/target/linux/ramips/mt7621/profiles/ubnt.mk
> @@ -0,0 +1,17 @@
> +#
> +# Copyright (C) 2015 OpenWrt.org
> +#
> +# This is free software, licensed under the GNU General Public License v2.
> +# See /LICENSE for more information.
> +#
> +
> +define Profile/UBNT-ERX
> + NAME:=Ubiquiti EdgeRouter X
> + FEATURES += nand
> + PACKAGES:=-kmod-mt76 -wpad-mini
> +endef
> +
> +define Profile/UBNT-ERX/Description
> + Package set compatible with the Ubiquiti EdgeRouter X
> +endef
> +$(eval $(call Profile,UBNT-ERX))
> diff --git a/target/linux/ramips/patches-3.18/0901-spansion_nand_id_fix.patch b/target/linux/ramips/patches-3.18/0901-spansion_nand_id_fix.patch
> new file mode 100644
> index 0000000..a327674
> --- /dev/null
> +++ b/target/linux/ramips/patches-3.18/0901-spansion_nand_id_fix.patch
> @@ -0,0 +1,43 @@
> +From 8b61a1a33e41456ebeafa0ebe7ec0fccf859861e Mon Sep 17 00:00:00 2001
> +From: Nikolay Martynov <mar.kolya at gmail.com>
> +Date: Wed, 25 Nov 2015 20:43:46 -0500
> +Subject: [PATCH] mtd: nand: Fix Spansion sparearea size detection
> +
> +According to datasheet S34ML02G2 and S34ML04G2 have
> +larger sparea area size than was detected.
> +
> +Signed-off-by: Nikolay Martynov <mar.kolya at gmail.com>
> +---
> + drivers/mtd/nand/nand_base.c | 9 +++++++++
> + 1 file changed, 9 insertions(+)
> +
> +--- a/drivers/mtd/nand/nand_base.c
> ++++ b/drivers/mtd/nand/nand_base.c
> +@@ -3399,6 +3399,7 @@ static void nand_decode_ext_id(struct mt
> + /*
> + * Field definitions are in the following datasheets:
> + * Old style (4,5 byte ID): Samsung K9GAG08U0M (p.32)
> ++ * Spansion S34ML02G2 (p.33)
> + * New Samsung (6 byte ID): Samsung K9GAG08U0F (p.44)
> + * Hynix MLC (6 byte ID): Hynix H27UBG8T2B (p.22)
> + *
> +@@ -3496,6 +3497,19 @@ static void nand_decode_ext_id(struct mt
> + *busw = (extid & 0x01) ? NAND_BUSWIDTH_16 : 0;
> +
> + /*
> ++ * Spansion S34ML0[24]G2 have oobsize twice as large
> ++ * as S34ML01G2 encoded in the same bit. We
> ++ * differinciate them by their ID length
> ++ */
> ++ if (id_data[0] == NAND_MFR_AMD
> ++ && (id_data[1] == 0xda
> ++ || id_data[1] == 0xdc
> ++ || id_data[1] == 0xca
> ++ || id_data[1] == 0xcc)) {
> ++ mtd->oobsize *= 2;
> ++ }
> ++
> ++ /*
> + * Toshiba 24nm raw SLC (i.e., not BENAND) have 32B OOB per
> + * 512B page. For Toshiba SLC, we decode the 5th/6th byte as
> + * follows:
> --
> 2.6.3
>
--
Martynov Nikolay.
Email: mar.kolya at gmail.com
_______________________________________________
openwrt-devel mailing list
openwrt-devel at lists.openwrt.org
https://lists.openwrt.org/cgi-bin/mailman/listinfo/openwrt-devel
More information about the openwrt-devel
mailing list