[OpenWrt-Devel] [PATCH] [v6] ramips: add additional support for MQmaker WiTi board
Sebastian Careba
nitroshift at yahoo.com
Sun Dec 6 04:01:36 EST 2015
The board is based on mt7621AT cpu, and has 16mb nor flash, 256mb of ram, 2 sata ports, microsd card slot, 1 USB 3.0 port and at least one 2.4 and one 5 ghz antenna.
This is the 6th submission that adds support for XHCI in the device tree file, along with switching the location of the 2 radio's and addition of the kmod-i2c-mt7621 in the default packages of the profile.
Patch v1 added initial support for MQmaker WiTi board. The device tree is based on PBR-M1.
Patch v2 changed the flash chip ID (w25q256 to gd25q128).
Patch v3 fixed the left-out entry for WiTi in 02_network.
Patch v4 fixed the naming scheme for MQmaker WiTi board.
Patch v5 reverts Patch v2 and introduces the use of 'jedec,spi-nor' to detect the flash chip ID.
Signed-off-by: Sebastian Careba <nitroshift at yahoo.com>
---
.../linux/ramips/base-files/etc/board.d/02_network | 1 +
target/linux/ramips/base-files/etc/diag.sh | 1 +
target/linux/ramips/base-files/lib/ramips.sh | 3 +
.../ramips/base-files/lib/upgrade/platform.sh | 1 +
target/linux/ramips/dts/WITI.dts | 146 +++++++++++++++++++++
target/linux/ramips/image/Makefile | 7 +-
target/linux/ramips/mt7621/profiles/mqmaker.mk | 20 +++
7 files changed, 178 insertions(+), 1 deletion(-)
create mode 100644 target/linux/ramips/dts/WITI.dts
create mode 100644 target/linux/ramips/mt7621/profiles/mqmaker.mk
diff --git a/target/linux/ramips/base-files/etc/board.d/02_network b/target/linux/ramips/base-files/etc/board.d/02_network
index 7e51229..0cdecb0 100755
--- a/target/linux/ramips/base-files/etc/board.d/02_network
+++ b/target/linux/ramips/base-files/etc/board.d/02_network
@@ -81,6 +81,7 @@ ramips_setup_interfaces()
wf-2881|\
whr-300hp2|\
whr-600d|\
+ witi|\
wsr-1166|\
wsr-600|\
wt1520|\
diff --git a/target/linux/ramips/base-files/etc/diag.sh b/target/linux/ramips/base-files/etc/diag.sh
index ff5fbf2..41e3a34 100644
--- a/target/linux/ramips/base-files/etc/diag.sh
+++ b/target/linux/ramips/base-files/etc/diag.sh
@@ -137,6 +137,7 @@ get_status_led() {
;;
pbr-m1|\
w306r-v20|\
+ witi|\
zbt-wr8305rt)
status_led="$board:green:sys"
;;
diff --git a/target/linux/ramips/base-files/lib/ramips.sh b/target/linux/ramips/base-files/lib/ramips.sh
index 92e13c0..c002b97 100755
--- a/target/linux/ramips/base-files/lib/ramips.sh
+++ b/target/linux/ramips/base-files/lib/ramips.sh
@@ -391,6 +391,9 @@ ramips_board_detect() {
*"WHR-G300N")
name="whr-g300n"
;;
+ *"WiTi")
+ name="witi"
+ ;;
*"WIZARD 8800")
name="wizard8800"
;;
diff --git a/target/linux/ramips/base-files/lib/upgrade/platform.sh b/target/linux/ramips/base-files/lib/upgrade/platform.sh
index 073593a..4ec3008 100755
--- a/target/linux/ramips/base-files/lib/upgrade/platform.sh
+++ b/target/linux/ramips/base-files/lib/upgrade/platform.sh
@@ -113,6 +113,7 @@ platform_check_image() {
whr-300hp2|\
whr-600d|\
whr-g300n|\
+ witi|\
wizfi630a|\
wl-330n|\
wl-330n3g|\
diff --git a/target/linux/ramips/dts/WITI.dts b/target/linux/ramips/dts/WITI.dts
new file mode 100644
index 0000000..ad8ef7b
--- /dev/null
+++ b/target/linux/ramips/dts/WITI.dts
@@ -0,0 +1,146 @@
+/dts-v1/;
+
+/include/ "mt7621.dtsi"
+
+/ {
+ compatible = "mediatek,mt7621-eval-board", "mediatek,mt7621-soc";
+ model = "MQmaker WiTi";
+
+ memory at 0 {
+ device_type = "memory";
+ reg = <0x0 0x10000000>;
+ };
+
+ chosen {
+ bootargs = "console=ttyS0,57600";
+ };
+
+ sdhci at 10130000 {
+ status = "okay";
+ };
+
+ xhci at 1E1C0000 {
+ status = "okay";
+ };
+
+ palmbus at 1E000000 {
+ spi at b00 {
+ status = "okay";
+
+ m25p80 at 0 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "jedec,spi-nor";
+ reg = <0 0>;
+ linux,modalias = "m25p80";
+ spi-max-frequency = <10000000>;
+
+ partition at 0 {
+ label = "u-boot";
+ reg = <0x0 0x30000>;
+ read-only;
+ };
+
+ partition at 30000 {
+ label = "u-boot-env";
+ reg = <0x30000 0x10000>;
+ read-only;
+ };
+
+ factory: partition at 40000 {
+ label = "factory";
+ reg = <0x40000 0x10000>;
+ read-only;
+ };
+
+ partition at 50000 {
+ label = "firmware";
+ reg = <0x50000 0xfb0000>;
+ };
+ };
+ };
+
+ i2c at 900 {
+ compatible = "ralink,i2c-mt7621";
+ reg = <0x900 0x100>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c_pins>;
+ status = "okay";
+
+ pcf8563: rtc at 51 {
+ status = "okay";
+ compatible = "nxp,pcf8563";
+ reg = <0x51>;
+ };
+ };
+ };
+
+ pcie at 1e140000 {
+ status = "okay";
+
+ pcie0 {
+ mt76 at 0,0 {
+ reg = <0x0000 0 0 0 0>;
+ device_type = "pci";
+ mediatek,mtd-eeprom = <&factory 0x8000>;
+ mediatek,2ghz = <0>;
+ };
+ };
+
+ pcie1 {
+ mt76 at 1,0 {
+ reg = <0x0000 0 0 0 0>;
+ device_type = "pci";
+ mediatek,mtd-eeprom = <&factory 0x0000>;
+ mediatek,5ghz = <0>;
+ };
+ };
+ };
+
+ ethernet at 1e100000 {
+ mtd-mac-address = <&factory 0xe000>;
+ };
+
+ gpio-leds {
+ compatible = "gpio-leds";
+
+ power {
+ label = "witi:green:power";
+ gpios = <&gpio0 25 1>;
+ };
+
+ sys {
+ label = "witi:green:sys";
+ gpios = <&gpio0 24 1>;
+ };
+
+ internet {
+ label = "witi:green:internet";
+ gpios = <&gpio0 23 1>;
+ };
+ };
+
+ gpio-keys-polled {
+ compatible = "gpio-keys-polled";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ poll-interval = <20>;
+
+ reset {
+ label = "reset";
+ gpios = <&gpio0 18 1>;
+ linux,code = <0x198>;
+ };
+ };
+
+ pinctrl {
+ state_default: pinctrl0 {
+ gpio {
+ ralink,group = "wdt", "rgmii2", "jtag", "mdio";
+ ralink,function = "gpio";
+ };
+ };
+ };
+};
diff --git a/target/linux/ramips/image/Makefile b/target/linux/ramips/image/Makefile
index e58d012..478ead9 100644
--- a/target/linux/ramips/image/Makefile
+++ b/target/linux/ramips/image/Makefile
@@ -954,7 +954,7 @@ endif
#
ifeq ($(SUBTARGET),mt7621)
- TARGET_DEVICES += mt7621 wsr-600 wsr-1166 dir-860l-b1 firewrt pbr-m1 re6500 sap-g3200u3 zbt-wg2626 wf-2881
+ TARGET_DEVICES += mt7621 wsr-600 wsr-1166 dir-860l-b1 firewrt pbr-m1 re6500 sap-g3200u3 witi wf-2881 zbt-wg2626
endif
define Device/mt7621
@@ -1004,6 +1004,11 @@ define Device/sap-g3200u3
DTS := SAP-G3200U3
endef
+define Device/witi
+ DTS := WITI
+ IMAGE_SIZE := $(ralink_default_fw_size_16M)
+endef
+
define Device/zbt-wg2626
DTS := ZBT-WG2626
IMAGE_SIZE := $(ralink_default_fw_size_16M)
diff --git a/target/linux/ramips/mt7621/profiles/mqmaker.mk b/target/linux/ramips/mt7621/profiles/mqmaker.mk
new file mode 100644
index 0000000..ae35e7d
--- /dev/null
+++ b/target/linux/ramips/mt7621/profiles/mqmaker.mk
@@ -0,0 +1,20 @@
+#
+# Copyright (C) 2015 OpenWrt.org
+#
+# This is free software, licensed under the GNU General Public License v2.
+# See /LICENSE for more information.
+#
+
+define Profile/witi
+ NAME:=MQmaker WiTi
+ FEATURES+=rtc
+ PACKAGES:=\
+ kmod-usb-core kmod-usb3 kmod-usb-hid kmod-sdhci-mt7620 \
+ kmod-ledtrig-usbdev kmod-ata-core kmod-ata-ahci \
+ kmod-rtc-pcf8563 kmod-i2c-mt7621
+endef
+
+define Profile/witi/Description
+ Package set compatible with MQmaker WiTi board.
+endef
+$(eval $(call Profile,witi))
--
2.1.4
_______________________________________________
openwrt-devel mailing list
openwrt-devel at lists.openwrt.org
https://lists.openwrt.org/cgi-bin/mailman/listinfo/openwrt-devel
More information about the openwrt-devel
mailing list