[OpenWrt-Devel] AR8334 switch support
Christian Mehlis
christian at m3hlis.de
Mon Apr 27 08:20:14 EDT 2015
Am 24.04.2015 um 20:05 schrieb Heiner Kallweit:
> Could you please test this patch and provide the dmesg output?
I tried your patch - dmesg is attached.
After the first run without success:
[ 0.890000] Atheros AR8216/AR8236/AR8316 ag71xx-mdio.0:00: Detected
AR8337 switch
I tweaked your patch a bit to print out more (attached).
############################################################
I also changed:
+ for (i = 0; i < AR8XXX_NUM_PHYS; i++) {
to
+ for (i = 0; i < AR8327_NUM_PORTS; i++) {
with this change we get:
[ 0.850000] switch0: Atheros AR833X rev. 2 switch registered on
ag71xx-mdio.0
[ 0.860000] Atheros AR8216/AR8236/AR8316 ag71xx-mdio.0:00: PHY 0
available
[ 0.860000] Atheros AR8216/AR8236/AR8316 ag71xx-mdio.0:00: PHY 1
available
[ 0.870000] Atheros AR8216/AR8236/AR8316 ag71xx-mdio.0:00: PHY 2
available
[ 0.880000] Atheros AR8216/AR8236/AR8316 ag71xx-mdio.0:00: PHY 3
available
[ 0.890000] Atheros AR8216/AR8236/AR8316 ag71xx-mdio.0:00: PHY 4
available
[ 0.890000] Atheros AR8216/AR8236/AR8316 ag71xx-mdio.0:00: PHY 5
available
[ 0.900000] Atheros AR8216/AR8236/AR8316 ag71xx-mdio.0:00: PHY 6
available
[ 0.910000] Atheros AR8216/AR8236/AR8316 ag71xx-mdio.0:00: Detected
AR8337 switch
#############################################################
It seems, that your phy based test is not working on ar8334...
Can we test other registers? I'll give it a try.
Best
Christian
-------------- next part --------------
# dmesg
[ 0.000000] Linux version 3.18.11 (c at black) (gcc version 4.8.3 (OpenWrt/Linaro GCC 4.8-2014.04 r45458) ) #1 Mon Apr 27 13:42:01 CEST 2015
[ 0.000000] MyLoader: sysp=cc7dbb0c, boardp=e9f041c4, parts=cbc748d9
[ 0.000000] bootconsole [early0] enabled
[ 0.000000] CPU0 revision is: 0001974c (MIPS 74Kc)
[ 0.000000] SoC: Atheros AR9344 rev 2
[ 0.000000] Determined physical RAM map:
[ 0.000000] memory: 08000000 @ 00000000 (usable)
[ 0.000000] Initrd not found or empty - disabling initrd
[ 0.000000] Zone ranges:
[ 0.000000] Normal [mem 0x00000000-0x07ffffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x00000000-0x07ffffff]
[ 0.000000] Initmem setup node 0 [mem 0x00000000-0x07ffffff]
[ 0.000000] On node 0 totalpages: 32768
[ 0.000000] free_area_init_node: node 0, pgdat 803560f0, node_mem_map 81000000
[ 0.000000] Normal zone: 256 pages used for memmap
[ 0.000000] Normal zone: 0 pages reserved
[ 0.000000] Normal zone: 32768 pages, LIFO batch:7
[ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
[ 0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
[ 0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
[ 0.000000] pcpu-alloc: [0] 0
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 32512
[ 0.000000] Kernel command line: board=WPJ344 console=ttyS0,115200 mtdparts=spi0.0:192k(u-boot)ro,16128k(firmware),64k(art)ro rootfstype=squashfs,jffs2 noinitrd
[ 0.000000] PID hash table entries: 512 (order: -1, 2048 bytes)
[ 0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
[ 0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.000000] Writing ErrCtl register=00000000
[ 0.000000] Readback ErrCtl register=00000000
[ 0.000000] Memory: 125920K/131072K available (2471K kernel code, 123K rwdata, 528K rodata, 260K init, 188K bss, 5152K reserved)
[ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.000000] NR_IRQS:51
[ 0.000000] Clocks: CPU:560.000MHz, DDR:450.000MHz, AHB:225.000MHz, Ref:40.000MHz
[ 0.000000] Calibrating delay loop... 278.93 BogoMIPS (lpj=1394688)
[ 0.070000] pid_max: default: 32768 minimum: 301
[ 0.070000] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.080000] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.080000] NET: Registered protocol family 16
[ 0.090000] MIPS: machine is Compex WPJ344
[ 0.100000] ar724x-pci ar724x-pci: PCIe link is down
[ 0.100000] registering PCI controller with io_map_base unset
[ 0.110000] ar71xx: using random MAC address for eth0
[ 0.330000] ar71xx: using random MAC address for eth1
[ 0.550000] PCI host bridge to bus 0000:00
[ 0.560000] pci_bus 0000:00: root bus resource [mem 0x10000000-0x13ffffff]
[ 0.560000] pci_bus 0000:00: root bus resource [io 0x0000]
[ 0.570000] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
[ 0.570000] pci_bus 0000:00: busn_res: [bus 00-ff] end is updated to 00
[ 0.570000] Switched to clocksource MIPS
[ 0.580000] NET: Registered protocol family 2
[ 0.580000] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.580000] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.590000] TCP: Hash tables configured (established 1024 bind 1024)
[ 0.590000] TCP: reno registered
[ 0.600000] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 0.600000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 0.610000] NET: Registered protocol family 1
[ 0.610000] PCI: CLS 0 bytes, default 32
[ 0.610000] futex hash table entries: 256 (order: -1, 3072 bytes)
[ 0.630000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.630000] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 0.640000] msgmni has been set to 245
[ 0.660000] io scheduler noop registered
[ 0.660000] io scheduler deadline registered (default)
[ 0.660000] Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled
[ 0.670000] console [ttyS0] disabled
[ 0.690000] serial8250.0: ttyS0 at MMIO 0x18020000 (irq = 11, base_baud = 2500000) is a 16550A
[ 0.700000] console [ttyS0] enabled
[ 0.710000] bootconsole [early0] disabled
[ 0.720000] m25p80 spi0.0: found mx25l12805d, expected m25p80
[ 0.730000] m25p80 spi0.0: mx25l12805d (16384 Kbytes)
[ 0.730000] 3 cmdlinepart partitions found on MTD device spi0.0
[ 0.740000] Creating 3 MTD partitions on "spi0.0":
[ 0.740000] 0x000000000000-0x000000030000 : "u-boot"
[ 0.750000] 0x000000030000-0x000000ff0000 : "firmware"
[ 0.790000] 2 uimage-fw partitions found on MTD device firmware
[ 0.790000] 0x000000030000-0x000000150000 : "kernel"
[ 0.800000] 0x000000150000-0x000000ff0000 : "rootfs"
[ 0.800000] mtd: device 3 (rootfs) set to be root filesystem
[ 0.810000] 1 squashfs-split partitions found on MTD device rootfs
[ 0.820000] 0x0000003c0000-0x000000ff0000 : "rootfs_data"
[ 0.820000] 0x000000ff0000-0x000001000000 : "art"
[ 0.840000] libphy: ag71xx_mdio: probed
[ 0.850000] switch0: Atheros AR833X rev. 2 switch registered on ag71xx-mdio.0
[ 0.860000] Atheros AR8216/AR8236/AR8316 ag71xx-mdio.0:00: PHY 0 available
[ 0.860000] Atheros AR8216/AR8236/AR8316 ag71xx-mdio.0:00: PHY 1 available
[ 0.870000] Atheros AR8216/AR8236/AR8316 ag71xx-mdio.0:00: PHY 2 available
[ 0.880000] Atheros AR8216/AR8236/AR8316 ag71xx-mdio.0:00: PHY 3 available
[ 0.890000] Atheros AR8216/AR8236/AR8316 ag71xx-mdio.0:00: PHY 4 available
[ 0.890000] Atheros AR8216/AR8236/AR8316 ag71xx-mdio.0:00: Detected AR8337 switch
[ 0.960000] libphy: ag71xx_mdio: probed
[ 1.560000] ag71xx ag71xx.0: connected to PHY at ag71xx-mdio.0:00 [uid=004dd036, driver=Atheros AR8216/AR8236/AR8316]
[ 1.570000] eth0: Atheros AG71xx at 0xb9000000, irq 4, mode:RGMII
[ 2.160000] ag71xx-mdio.1: Found an AR934X built-in switch
[ 2.200000] eth1: Atheros AG71xx at 0xba000000, irq 5, mode:GMII
[ 2.210000] TCP: cubic registered
[ 2.210000] NET: Registered protocol family 17
[ 2.210000] bridge: automatic filtering via arp/ip/ip6tables has been deprecated. Update your scripts to load br_netfilter if you need this.
[ 2.230000] 8021q: 802.1Q VLAN Support v1.8
[ 2.240000] VFS: Mounted root (squashfs filesystem) readonly on device 31:3.
[ 2.250000] Freeing unused kernel memory: 260K (8036f000 - 803b0000)
[ 3.270000] init: failed to symlink /tmp -> /var
[ 3.270000] init: Console is alive
[ 3.270000] init: - watchdog -
[ 4.460000] usbcore: registered new interface driver usbfs
[ 4.460000] usbcore: registered new interface driver hub
[ 4.470000] usbcore: registered new device driver usb
[ 4.480000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 4.480000] ehci-platform: EHCI generic platform driver
[ 4.490000] ehci-platform ehci-platform: EHCI Host Controller
[ 4.500000] ehci-platform ehci-platform: new USB bus registered, assigned bus number 1
[ 4.510000] ehci-platform ehci-platform: irq 3, io mem 0x1b000000
[ 4.530000] ehci-platform ehci-platform: USB 2.0 started, EHCI 1.00
[ 4.530000] hub 1-0:1.0: USB hub found
[ 4.540000] hub 1-0:1.0: 1 port detected
[ 4.540000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 4.550000] ohci-platform: OHCI generic platform driver
[ 5.280000] init: - preinit -
[ 6.030000] random: procd urandom read with 9 bits of entropy available
[ 7.730000] eth0: link up (1000Mbps/Full duplex)
[ 9.290000] mount_root: jffs2 not ready yet, using temporary tmpfs overlay
[ 9.330000] eth0: link down
[ 9.340000] procd: - early -
[ 9.340000] procd: - watchdog -
[ 9.960000] procd: - ubus -
[ 10.980000] procd: - init -
[ 11.710000] NET: Registered protocol family 10
[ 11.720000] ip6_tables: (C) 2000-2006 Netfilter Core Team
[ 11.740000] Loading modules backported from Linux version master-2015-03-09-0-g141f155
[ 11.750000] Backport generated by backports.git backports-20150129-0-gdd4a670
[ 11.780000] cfg80211: Calling CRDA to update world regulatory domain
[ 11.780000] cfg80211: World regulatory domain updated:
[ 11.790000] cfg80211: DFS Master region: unset
[ 11.790000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time)
[ 11.800000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
[ 11.810000] cfg80211: (2457000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
[ 11.820000] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (N/A, 2000 mBm), (N/A)
[ 11.830000] cfg80211: (5170000 KHz - 5250000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A)
[ 11.840000] cfg80211: (5250000 KHz - 5330000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A, 2000 mBm), (0 s)
[ 11.840000] cfg80211: (5490000 KHz - 5730000 KHz @ 160000 KHz), (N/A, 2000 mBm), (0 s)
[ 11.850000] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A)
[ 11.860000] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm), (N/A)
[ 11.970000] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 11.980000] nf_conntrack version 0.5.0 (1971 buckets, 7884 max)
[ 12.020000] xt_time: kernel timezone is -0000
[ 12.040000] PPP generic driver version 2.4.2
[ 12.050000] NET: Registered protocol family 24
[ 12.070000] ath: EEPROM regdomain: 0x0
[ 12.070000] ath: EEPROM indicates default country code should be used
[ 12.070000] ath: doing EEPROM country->regdmn map search
[ 12.070000] ath: country maps to regdmn code: 0x3a
[ 12.070000] ath: Country alpha2 being used: US
[ 12.070000] ath: Regpair used: 0x3a
[ 12.080000] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
[ 12.080000] ieee80211 phy0: Atheros AR9340 Rev:2 mem=0xb8100000, irq=47
[ 12.090000] cfg80211: Calling CRDA for country: US
[ 12.110000] cfg80211: Regulatory domain changed to country: US
[ 12.110000] cfg80211: DFS Master region: FCC
[ 12.120000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time)
[ 12.130000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 3000 mBm), (N/A)
[ 12.130000] cfg80211: (5170000 KHz - 5250000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A, 1700 mBm), (N/A)
[ 12.140000] cfg80211: (5250000 KHz - 5330000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A, 2300 mBm), (0 s)
[ 12.150000] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 3000 mBm), (N/A)
[ 12.160000] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 4000 mBm), (N/A)
[ 18.860000] jffs2_scan_eraseblock(): End of filesystem marker found at 0x0
[ 18.880000] jffs2_build_filesystem(): unlocking the mtd device... done.
[ 18.880000] jffs2_build_filesystem(): erasing all blocks after the end marker...
[ 22.700000] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 22.750000] device eth0.1 entered promiscuous mode
[ 22.750000] device eth0 entered promiscuous mode
[ 22.790000] IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready
[ 22.830000] IPv6: ADDRCONF(NETDEV_UP): eth0.2: link is not ready
[ 23.880000] eth0: link up (1000Mbps/Full duplex)
[ 23.880000] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 23.940000] br-lan: port 1(eth0.1) entered forwarding state
[ 23.940000] br-lan: port 1(eth0.1) entered forwarding state
[ 23.950000] IPv6: ADDRCONF(NETDEV_CHANGE): eth0.2: link becomes ready
[ 23.950000] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
[ 25.920000] Atheros AR8216/AR8236/AR8316 ag71xx-mdio.0:00: Port 3 is up
[ 25.940000] br-lan: port 1(eth0.1) entered forwarding state
[ 78.810000] done.
[ 78.810000] jffs2: notice: (922) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found.
[ 80.610000] random: nonblocking pool is initialized
-------------- next part --------------
A non-text attachment was scrubbed...
Name: ar8334.patch
Type: text/x-patch
Size: 4538 bytes
Desc: not available
URL: <http://lists.infradead.org/pipermail/openwrt-devel/attachments/20150427/97ba635b/attachment.bin>
-------------- next part --------------
_______________________________________________
openwrt-devel mailing list
openwrt-devel at lists.openwrt.org
https://lists.openwrt.org/cgi-bin/mailman/listinfo/openwrt-devel
More information about the openwrt-devel
mailing list