[OpenWrt-Devel] [PATCH 5/6] ipq806x: add platform usb support
Mathieu Olivari
mathieu at codeaurora.org
Thu Apr 2 23:30:10 EDT 2015
This change adds DWC3 QCOM USB phys and TCSR drivers. These are
cherry-picked from the following LKML threads:
*dwc3 qcom: https://lkml.org/lkml/2014/9/12/599
*tcsr: https://lkml.org/lkml/2015/2/9/579
We're also adding an additional patch to add the corresponding dev nodes
in the IPQ806x and AP148 dts files.
Signed-off-by: Mathieu Olivari <mathieu at codeaurora.org>
---
...b-phy-Add-Qualcomm-DWC3-HS-SS-PHY-drivers.patch | 511 +++++++++++++++++++++
...1-ARM-qcom-add-USB-nodes-to-ipq806x-ap148.patch | 125 +++++
...qcom-gsbi-Add-support-for-ADM-CRCI-muxing.patch | 258 +++++++++++
.../103-ARM-DT-ipq8064-Add-TCSR-support.patch | 65 +++
.../patches-3.18/700-add-gmac-dts-suport.patch | 21 +-
5 files changed, 969 insertions(+), 11 deletions(-)
create mode 100644 target/linux/ipq806x/patches-3.18/100-usb-phy-Add-Qualcomm-DWC3-HS-SS-PHY-drivers.patch
create mode 100644 target/linux/ipq806x/patches-3.18/101-ARM-qcom-add-USB-nodes-to-ipq806x-ap148.patch
create mode 100644 target/linux/ipq806x/patches-3.18/102-soc-qcom-gsbi-Add-support-for-ADM-CRCI-muxing.patch
create mode 100644 target/linux/ipq806x/patches-3.18/103-ARM-DT-ipq8064-Add-TCSR-support.patch
diff --git a/target/linux/ipq806x/patches-3.18/100-usb-phy-Add-Qualcomm-DWC3-HS-SS-PHY-drivers.patch b/target/linux/ipq806x/patches-3.18/100-usb-phy-Add-Qualcomm-DWC3-HS-SS-PHY-drivers.patch
new file mode 100644
index 0000000..25803b8
--- /dev/null
+++ b/target/linux/ipq806x/patches-3.18/100-usb-phy-Add-Qualcomm-DWC3-HS-SS-PHY-drivers.patch
@@ -0,0 +1,511 @@
+--- a/drivers/phy/Kconfig
++++ b/drivers/phy/Kconfig
+@@ -256,4 +256,15 @@ config PHY_STIH41X_USB
+ Enable this to support the USB transceiver that is part of
+ STMicroelectronics STiH41x SoC series.
+
++config PHY_QCOM_DWC3
++ tristate "QCOM DWC3 USB PHY support"
++ depends on ARCH_QCOM
++ depends on HAS_IOMEM
++ depends on OF
++ select GENERIC_PHY
++ help
++ This option enables support for the Synopsis PHYs present inside the
++ Qualcomm USB3.0 DWC3 controller. This driver supports both HS and SS
++ PHY controllers.
++
+ endmenu
+--- a/drivers/phy/Makefile
++++ b/drivers/phy/Makefile
+@@ -31,3 +31,4 @@ obj-$(CONFIG_PHY_ST_SPEAR1340_MIPHY) +=
+ obj-$(CONFIG_PHY_XGENE) += phy-xgene.o
+ obj-$(CONFIG_PHY_STIH407_USB) += phy-stih407-usb.o
+ obj-$(CONFIG_PHY_STIH41X_USB) += phy-stih41x-usb.o
++obj-$(CONFIG_PHY_QCOM_DWC3) += phy-qcom-dwc3.o
+--- /dev/null
++++ b/drivers/phy/phy-qcom-dwc3.c
+@@ -0,0 +1,483 @@
++/* Copyright (c) 2013-2014, Code Aurora Forum. All rights reserved.
++ *
++ * This program is free software; you can redistribute it and/or modify
++ * it under the terms of the GNU General Public License version 2 and
++ * only version 2 as published by the Free Software Foundation.
++ *
++ * This program is distributed in the hope that it will be useful,
++ * but WITHOUT ANY WARRANTY; without even the implied warranty of
++ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
++ * GNU General Public License for more details.
++ */
++
++#include <linux/clk.h>
++#include <linux/err.h>
++#include <linux/io.h>
++#include <linux/module.h>
++#include <linux/of.h>
++#include <linux/phy/phy.h>
++#include <linux/platform_device.h>
++#include <linux/delay.h>
++
++/**
++ * USB QSCRATCH Hardware registers
++ */
++#define QSCRATCH_GENERAL_CFG (0x08)
++#define HSUSB_PHY_CTRL_REG (0x10)
++
++/* PHY_CTRL_REG */
++#define HSUSB_CTRL_DMSEHV_CLAMP BIT(24)
++#define HSUSB_CTRL_USB2_SUSPEND BIT(23)
++#define HSUSB_CTRL_UTMI_CLK_EN BIT(21)
++#define HSUSB_CTRL_UTMI_OTG_VBUS_VALID BIT(20)
++#define HSUSB_CTRL_USE_CLKCORE BIT(18)
++#define HSUSB_CTRL_DPSEHV_CLAMP BIT(17)
++#define HSUSB_CTRL_COMMONONN BIT(11)
++#define HSUSB_CTRL_ID_HV_CLAMP BIT(9)
++#define HSUSB_CTRL_OTGSESSVLD_CLAMP BIT(8)
++#define HSUSB_CTRL_CLAMP_EN BIT(7)
++#define HSUSB_CTRL_RETENABLEN BIT(1)
++#define HSUSB_CTRL_POR BIT(0)
++
++/* QSCRATCH_GENERAL_CFG */
++#define HSUSB_GCFG_XHCI_REV BIT(2)
++
++/**
++ * USB QSCRATCH Hardware registers
++ */
++#define SSUSB_PHY_CTRL_REG (0x00)
++#define SSUSB_PHY_PARAM_CTRL_1 (0x04)
++#define SSUSB_PHY_PARAM_CTRL_2 (0x08)
++#define CR_PROTOCOL_DATA_IN_REG (0x0c)
++#define CR_PROTOCOL_DATA_OUT_REG (0x10)
++#define CR_PROTOCOL_CAP_ADDR_REG (0x14)
++#define CR_PROTOCOL_CAP_DATA_REG (0x18)
++#define CR_PROTOCOL_READ_REG (0x1c)
++#define CR_PROTOCOL_WRITE_REG (0x20)
++
++/* PHY_CTRL_REG */
++#define SSUSB_CTRL_REF_USE_PAD BIT(28)
++#define SSUSB_CTRL_TEST_POWERDOWN BIT(27)
++#define SSUSB_CTRL_LANE0_PWR_PRESENT BIT(24)
++#define SSUSB_CTRL_SS_PHY_EN BIT(8)
++#define SSUSB_CTRL_SS_PHY_RESET BIT(7)
++
++/* SSPHY control registers */
++#define SSPHY_CTRL_RX_OVRD_IN_HI(lane) (0x1006 + 0x100 * lane)
++#define SSPHY_CTRL_TX_OVRD_DRV_LO(lane) (0x1002 + 0x100 * lane)
++
++/* RX OVRD IN HI bits */
++#define RX_OVRD_IN_HI_RX_RESET_OVRD BIT(13)
++#define RX_OVRD_IN_HI_RX_RX_RESET BIT(12)
++#define RX_OVRD_IN_HI_RX_EQ_OVRD BIT(11)
++#define RX_OVRD_IN_HI_RX_EQ_MASK 0x0700
++#define RX_OVRD_IN_HI_RX_EQ_SHIFT 8
++#define RX_OVRD_IN_HI_RX_EQ_EN_OVRD BIT(7)
++#define RX_OVRD_IN_HI_RX_EQ_EN BIT(6)
++#define RX_OVRD_IN_HI_RX_LOS_FILTER_OVRD BIT(5)
++#define RX_OVRD_IN_HI_RX_LOS_FILTER_MASK 0x0018
++#define RX_OVRD_IN_HI_RX_RATE_OVRD BIT(2)
++#define RX_OVRD_IN_HI_RX_RATE_MASK 0x0003
++
++/* TX OVRD DRV LO register bits */
++#define TX_OVRD_DRV_LO_AMPLITUDE_MASK 0x007F
++#define TX_OVRD_DRV_LO_PREEMPH_MASK 0x3F80
++#define TX_OVRD_DRV_LO_PREEMPH_SHIFT 7
++#define TX_OVRD_DRV_LO_EN BIT(14)
++
++struct qcom_dwc3_usb_phy {
++ void __iomem *base;
++ struct device *dev;
++ struct phy *phy;
++
++ int (*phy_init)(struct qcom_dwc3_usb_phy *phy_dwc3);
++ int (*phy_exit)(struct qcom_dwc3_usb_phy *phy_dwc3);
++
++ struct clk *xo_clk;
++ struct clk *ref_clk;
++};
++
++/**
++ * Write register and read back masked value to confirm it is written
++ *
++ * @base - QCOM DWC3 PHY base virtual address.
++ * @offset - register offset.
++ * @mask - register bitmask specifying what should be updated
++ * @val - value to write.
++ */
++static inline void qcom_dwc3_phy_write_readback(
++ struct qcom_dwc3_usb_phy *phy_dwc3, u32 offset,
++ const u32 mask, u32 val)
++{
++ u32 write_val, tmp = readl(phy_dwc3->base + offset);
++
++ tmp &= ~mask; /* retain other bits */
++ write_val = tmp | val;
++
++ writel(write_val, phy_dwc3->base + offset);
++
++ /* Read back to see if val was written */
++ tmp = readl(phy_dwc3->base + offset);
++ tmp &= mask; /* clear other bits */
++
++ if (tmp != val)
++ dev_err(phy_dwc3->dev, "write: %x to QSCRATCH: %x FAILED\n",
++ val, offset);
++}
++
++static int wait_for_latch(void __iomem *addr)
++{
++ u32 retry = 10;
++
++ while (true) {
++ if (!readl(addr))
++ break;
++
++ if (--retry == 0)
++ return -ETIMEDOUT;
++
++ usleep_range(10, 20);
++ }
++
++ return 0;
++}
++
++/**
++ * Write SSPHY register
++ *
++ * @base - QCOM DWC3 PHY base virtual address.
++ * @addr - SSPHY address to write.
++ * @val - value to write.
++ */
++static int qcom_dwc3_ss_write_phycreg(void __iomem *base, u32 addr, u32 val)
++{
++ int ret;
++
++ writel(addr, base + CR_PROTOCOL_DATA_IN_REG);
++ writel(0x1, base + CR_PROTOCOL_CAP_ADDR_REG);
++
++ ret = wait_for_latch(base + CR_PROTOCOL_CAP_ADDR_REG);
++ if (ret)
++ goto err_wait;
++
++ writel(val, base + CR_PROTOCOL_DATA_IN_REG);
++ writel(0x1, base + CR_PROTOCOL_CAP_DATA_REG);
++
++ ret = wait_for_latch(base + CR_PROTOCOL_CAP_DATA_REG);
++ if (ret)
++ goto err_wait;
++
++ writel(0x1, base + CR_PROTOCOL_WRITE_REG);
++
++ ret = wait_for_latch(base + CR_PROTOCOL_WRITE_REG);
++
++err_wait:
++ return ret;
++}
++
++/**
++ * Read SSPHY register.
++ *
++ * @base - QCOM DWC3 PHY base virtual address.
++ * @addr - SSPHY address to read.
++ */
++static int qcom_dwc3_ss_read_phycreg(void __iomem *base, u32 addr, u32 *val)
++{
++ int ret;
++ bool first_read = true;
++
++ writel(addr, base + CR_PROTOCOL_DATA_IN_REG);
++ writel(0x1, base + CR_PROTOCOL_CAP_ADDR_REG);
++
++ ret = wait_for_latch(base + CR_PROTOCOL_CAP_ADDR_REG);
++ if (ret)
++ goto err_wait;
++
++ /*
++ * Due to hardware bug, first read of SSPHY register might be
++ * incorrect. Hence as workaround, SW should perform SSPHY register
++ * read twice, but use only second read and ignore first read.
++ */
++retry:
++ writel(0x1, base + CR_PROTOCOL_READ_REG);
++
++ ret = wait_for_latch(base + CR_PROTOCOL_READ_REG);
++ if (ret)
++ goto err_wait;
++
++ if (first_read) {
++ readl(base + CR_PROTOCOL_DATA_OUT_REG);
++ first_read = false;
++ goto retry;
++ }
++
++ *val = readl(base + CR_PROTOCOL_DATA_OUT_REG);
++
++err_wait:
++ return ret;
++}
++
++static int qcom_dwc3_phy_power_on(struct phy *phy)
++{
++ int ret;
++ struct qcom_dwc3_usb_phy *phy_dwc3 = phy_get_drvdata(phy);
++
++ ret = clk_prepare_enable(phy_dwc3->xo_clk);
++ if (ret)
++ return ret;
++
++ ret = clk_prepare_enable(phy_dwc3->ref_clk);
++ if (ret)
++ clk_disable_unprepare(phy_dwc3->xo_clk);
++
++ return ret;
++}
++
++static int qcom_dwc3_phy_power_off(struct phy *phy)
++{
++ struct qcom_dwc3_usb_phy *phy_dwc3 = phy_get_drvdata(phy);
++
++ clk_disable_unprepare(phy_dwc3->ref_clk);
++ clk_disable_unprepare(phy_dwc3->xo_clk);
++
++ return 0;
++}
++
++static int qcom_dwc3_hs_phy_init(struct qcom_dwc3_usb_phy *phy_dwc3)
++{
++ u32 val;
++
++ /*
++ * HSPHY Initialization: Enable UTMI clock, select 19.2MHz fsel
++ * enable clamping, and disable RETENTION (power-on default is ENABLED)
++ */
++ val = HSUSB_CTRL_DPSEHV_CLAMP | HSUSB_CTRL_DMSEHV_CLAMP |
++ HSUSB_CTRL_RETENABLEN | HSUSB_CTRL_COMMONONN |
++ HSUSB_CTRL_OTGSESSVLD_CLAMP | HSUSB_CTRL_ID_HV_CLAMP |
++ HSUSB_CTRL_DPSEHV_CLAMP | HSUSB_CTRL_UTMI_OTG_VBUS_VALID |
++ HSUSB_CTRL_UTMI_CLK_EN | HSUSB_CTRL_CLAMP_EN | 0x70;
++
++ /* use core clock if external reference is not present */
++ if (!phy_dwc3->xo_clk)
++ val |= HSUSB_CTRL_USE_CLKCORE;
++
++ writel(val, phy_dwc3->base + HSUSB_PHY_CTRL_REG);
++ usleep_range(2000, 2200);
++
++ /* Disable (bypass) VBUS and ID filters */
++ writel(HSUSB_GCFG_XHCI_REV, phy_dwc3->base + QSCRATCH_GENERAL_CFG);
++
++ return 0;
++}
++
++static int qcom_dwc3_ss_phy_init(struct qcom_dwc3_usb_phy *phy_dwc3)
++{
++ int ret;
++ u32 data = 0;
++
++ /* reset phy */
++ data = readl_relaxed(phy_dwc3->base + SSUSB_PHY_CTRL_REG);
++ writel_relaxed(data | SSUSB_CTRL_SS_PHY_RESET,
++ phy_dwc3->base + SSUSB_PHY_CTRL_REG);
++ usleep_range(2000, 2200);
++ writel_relaxed(data, phy_dwc3->base + SSUSB_PHY_CTRL_REG);
++
++ /* clear REF_PAD if we don't have XO clk */
++ if (!phy_dwc3->xo_clk)
++ data &= ~SSUSB_CTRL_REF_USE_PAD;
++ else
++ data |= SSUSB_CTRL_REF_USE_PAD;
++
++ writel_relaxed(data, phy_dwc3->base + SSUSB_PHY_CTRL_REG);
++ msleep(30);
++
++ data |= SSUSB_CTRL_SS_PHY_EN | SSUSB_CTRL_LANE0_PWR_PRESENT;
++ writel_relaxed(data, phy_dwc3->base + SSUSB_PHY_CTRL_REG);
++
++ /*
++ * Fix RX Equalization setting as follows
++ * LANE0.RX_OVRD_IN_HI. RX_EQ_EN set to 0
++ * LANE0.RX_OVRD_IN_HI.RX_EQ_EN_OVRD set to 1
++ * LANE0.RX_OVRD_IN_HI.RX_EQ set to 3
++ * LANE0.RX_OVRD_IN_HI.RX_EQ_OVRD set to 1
++ */
++ ret = qcom_dwc3_ss_read_phycreg(phy_dwc3->base,
++ SSPHY_CTRL_RX_OVRD_IN_HI(0), &data);
++ if (ret)
++ goto err_phy_trans;
++
++ data &= ~RX_OVRD_IN_HI_RX_EQ_EN;
++ data |= RX_OVRD_IN_HI_RX_EQ_EN_OVRD;
++ data &= ~RX_OVRD_IN_HI_RX_EQ_MASK;
++ data |= 0x3 << RX_OVRD_IN_HI_RX_EQ_SHIFT;
++ data |= RX_OVRD_IN_HI_RX_EQ_OVRD;
++ ret = qcom_dwc3_ss_write_phycreg(phy_dwc3->base,
++ SSPHY_CTRL_RX_OVRD_IN_HI(0), data);
++ if (ret)
++ goto err_phy_trans;
++
++ /*
++ * Set EQ and TX launch amplitudes as follows
++ * LANE0.TX_OVRD_DRV_LO.PREEMPH set to 22
++ * LANE0.TX_OVRD_DRV_LO.AMPLITUDE set to 127
++ * LANE0.TX_OVRD_DRV_LO.EN set to 1.
++ */
++ ret = qcom_dwc3_ss_read_phycreg(phy_dwc3->base,
++ SSPHY_CTRL_TX_OVRD_DRV_LO(0), &data);
++ if (ret)
++ goto err_phy_trans;
++
++ data &= ~TX_OVRD_DRV_LO_PREEMPH_MASK;
++ data |= 0x16 << TX_OVRD_DRV_LO_PREEMPH_SHIFT;
++ data &= ~TX_OVRD_DRV_LO_AMPLITUDE_MASK;
++ data |= 0x7f;
++ data |= TX_OVRD_DRV_LO_EN;
++ ret = qcom_dwc3_ss_write_phycreg(phy_dwc3->base,
++ SSPHY_CTRL_TX_OVRD_DRV_LO(0), data);
++ if (ret)
++ goto err_phy_trans;
++
++ /*
++ * Set the QSCRATCH PHY_PARAM_CTRL1 parameters as follows
++ * TX_FULL_SWING [26:20] amplitude to 127
++ * TX_DEEMPH_3_5DB [13:8] to 22
++ * LOS_BIAS [2:0] to 0x5
++ */
++ qcom_dwc3_phy_write_readback(phy_dwc3, SSUSB_PHY_PARAM_CTRL_1,
++ 0x07f03f07, 0x07f01605);
++
++err_phy_trans:
++ return ret;
++}
++
++static int qcom_dwc3_ss_phy_exit(struct qcom_dwc3_usb_phy *phy_dwc3)
++{
++ /* Sequence to put SSPHY in low power state:
++ * 1. Clear REF_PHY_EN in PHY_CTRL_REG
++ * 2. Clear REF_USE_PAD in PHY_CTRL_REG
++ * 3. Set TEST_POWERED_DOWN in PHY_CTRL_REG to enable PHY retention
++ * 4. Disable SSPHY ref clk
++ */
++ qcom_dwc3_phy_write_readback(phy_dwc3, SSUSB_PHY_CTRL_REG,
++ SSUSB_CTRL_SS_PHY_EN, 0x0);
++ qcom_dwc3_phy_write_readback(phy_dwc3, SSUSB_PHY_CTRL_REG,
++ SSUSB_CTRL_REF_USE_PAD, 0x0);
++ qcom_dwc3_phy_write_readback(phy_dwc3, SSUSB_PHY_CTRL_REG,
++ 0x0, SSUSB_CTRL_TEST_POWERDOWN);
++
++ return 0;
++}
++
++static int qcom_dwc3_phy_init(struct phy *phy)
++{
++ struct qcom_dwc3_usb_phy *phy_dwc3 = phy_get_drvdata(phy);
++
++ if (phy_dwc3->phy_init)
++ return phy_dwc3->phy_init(phy_dwc3);
++
++ return 0;
++}
++
++static int qcom_dwc3_phy_exit(struct phy *phy)
++{
++ struct qcom_dwc3_usb_phy *phy_dwc3 = phy_get_drvdata(phy);
++
++ if (phy_dwc3->phy_exit)
++ return qcom_dwc3_ss_phy_exit(phy_dwc3);
++
++ return 0;
++}
++
++static struct phy_ops qcom_dwc3_phy_ops = {
++ .init = qcom_dwc3_phy_init,
++ .exit = qcom_dwc3_phy_exit,
++ .power_on = qcom_dwc3_phy_power_on,
++ .power_off = qcom_dwc3_phy_power_off,
++ .owner = THIS_MODULE,
++};
++
++static const struct of_device_id qcom_dwc3_phy_table[] = {
++ { .compatible = "qcom,dwc3-hs-usb-phy", },
++ { .compatible = "qcom,dwc3-ss-usb-phy", },
++ { /* Sentinel */ }
++};
++MODULE_DEVICE_TABLE(of, qcom_dwc3_phy_table);
++
++static int qcom_dwc3_phy_probe(struct platform_device *pdev)
++{
++ struct qcom_dwc3_usb_phy *phy_dwc3;
++ struct phy_provider *phy_provider;
++ struct resource *res;
++
++ phy_dwc3 = devm_kzalloc(&pdev->dev, sizeof(*phy_dwc3), GFP_KERNEL);
++ if (!phy_dwc3)
++ return -ENOMEM;
++
++ platform_set_drvdata(pdev, phy_dwc3);
++
++ phy_dwc3->dev = &pdev->dev;
++
++ res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
++ phy_dwc3->base = devm_ioremap_resource(phy_dwc3->dev, res);
++ if (IS_ERR(phy_dwc3->base))
++ return PTR_ERR(phy_dwc3->base);
++
++ phy_dwc3->ref_clk = devm_clk_get(phy_dwc3->dev, "ref");
++ if (IS_ERR(phy_dwc3->ref_clk)) {
++ dev_dbg(phy_dwc3->dev, "cannot get reference clock\n");
++ return PTR_ERR(phy_dwc3->ref_clk);
++ }
++
++ if (of_device_is_compatible(pdev->dev.of_node,
++ "qcom,dwc3-hs-usb-phy")) {
++ clk_set_rate(phy_dwc3->ref_clk, 60000000);
++ phy_dwc3->phy_init = qcom_dwc3_hs_phy_init;
++ } else if (of_device_is_compatible(pdev->dev.of_node,
++ "qcom,dwc3-ss-usb-phy")) {
++ phy_dwc3->phy_init = qcom_dwc3_ss_phy_init;
++ phy_dwc3->phy_exit = qcom_dwc3_ss_phy_exit;
++ clk_set_rate(phy_dwc3->ref_clk, 125000000);
++ } else {
++ dev_err(phy_dwc3->dev, "Unknown phy\n");
++ return -EINVAL;
++ }
++
++ phy_dwc3->xo_clk = devm_clk_get(phy_dwc3->dev, "xo");
++ if (IS_ERR(phy_dwc3->xo_clk)) {
++ dev_dbg(phy_dwc3->dev, "cannot get TCXO clock\n");
++ phy_dwc3->xo_clk = NULL;
++ }
++
++ phy_dwc3->phy = devm_phy_create(phy_dwc3->dev, NULL, &qcom_dwc3_phy_ops,
++ NULL);
++
++ if (IS_ERR(phy_dwc3->phy))
++ return PTR_ERR(phy_dwc3->phy);
++
++ phy_set_drvdata(phy_dwc3->phy, phy_dwc3);
++
++ phy_provider = devm_of_phy_provider_register(phy_dwc3->dev,
++ of_phy_simple_xlate);
++
++ if (IS_ERR(phy_provider))
++ return PTR_ERR(phy_provider);
++
++ return 0;
++}
++
++static struct platform_driver qcom_dwc3_phy_driver = {
++ .probe = qcom_dwc3_phy_probe,
++ .driver = {
++ .name = "qcom-dwc3-usb-phy",
++ .owner = THIS_MODULE,
++ .of_match_table = qcom_dwc3_phy_table,
++ },
++};
++
++module_platform_driver(qcom_dwc3_phy_driver);
++
++MODULE_ALIAS("platform:phy-qcom-dwc3");
++MODULE_LICENSE("GPL v2");
++MODULE_AUTHOR("Andy Gross <agross at codeaurora.org>");
++MODULE_AUTHOR("Ivan T. Ivanov <iivanov at mm-sol.com>");
++MODULE_DESCRIPTION("DesignWare USB3 QCOM PHY driver");
diff --git a/target/linux/ipq806x/patches-3.18/101-ARM-qcom-add-USB-nodes-to-ipq806x-ap148.patch b/target/linux/ipq806x/patches-3.18/101-ARM-qcom-add-USB-nodes-to-ipq806x-ap148.patch
new file mode 100644
index 0000000..f1b4164
--- /dev/null
+++ b/target/linux/ipq806x/patches-3.18/101-ARM-qcom-add-USB-nodes-to-ipq806x-ap148.patch
@@ -0,0 +1,125 @@
+--- a/arch/arm/boot/dts/qcom-ipq8064-ap148.dts
++++ b/arch/arm/boot/dts/qcom-ipq8064-ap148.dts
+@@ -112,5 +112,29 @@
+ sata at 29000000 {
+ status = "ok";
+ };
++
++ phy at 100f8800 { /* USB3 port 1 HS phy */
++ status = "ok";
++ };
++
++ phy at 100f8830 { /* USB3 port 1 SS phy */
++ status = "ok";
++ };
++
++ phy at 110f8800 { /* USB3 port 0 HS phy */
++ status = "ok";
++ };
++
++ phy at 110f8830 { /* USB3 port 0 SS phy */
++ status = "ok";
++ };
++
++ usb30 at 0 {
++ status = "ok";
++ };
++
++ usb30 at 1 {
++ status = "ok";
++ };
+ };
+ };
+--- a/arch/arm/boot/dts/qcom-ipq8064.dtsi
++++ b/arch/arm/boot/dts/qcom-ipq8064.dtsi
+@@ -291,5 +291,90 @@
+ #clock-cells = <1>;
+ #reset-cells = <1>;
+ };
++
++ hs_phy_1: phy at 100f8800 {
++ compatible = "qcom,dwc3-hs-usb-phy";
++ reg = <0x100f8800 0x30>;
++ clocks = <&gcc USB30_1_UTMI_CLK>;
++ clock-names = "ref";
++ #phy-cells = <0>;
++
++ status = "disabled";
++ };
++
++ ss_phy_1: phy at 100f8830 {
++ compatible = "qcom,dwc3-ss-usb-phy";
++ reg = <0x100f8830 0x30>;
++ clocks = <&gcc USB30_1_MASTER_CLK>;
++ clock-names = "ref";
++ #phy-cells = <0>;
++
++ status = "disabled";
++ };
++
++ hs_phy_0: phy at 110f8800 {
++ compatible = "qcom,dwc3-hs-usb-phy";
++ reg = <0x110f8800 0x30>;
++ clocks = <&gcc USB30_0_UTMI_CLK>;
++ clock-names = "ref";
++ #phy-cells = <0>;
++
++ status = "disabled";
++ };
++
++ ss_phy_0: phy at 110f8830 {
++ compatible = "qcom,dwc3-ss-usb-phy";
++ reg = <0x110f8830 0x30>;
++ clocks = <&gcc USB30_0_MASTER_CLK>;
++ clock-names = "ref";
++ #phy-cells = <0>;
++
++ status = "disabled";
++ };
++
++ usb3_0: usb30 at 0 {
++ compatible = "qcom,dwc3";
++ #address-cells = <1>;
++ #size-cells = <1>;
++ clocks = <&gcc USB30_0_MASTER_CLK>;
++ clock-names = "core";
++
++ ranges;
++
++ status = "disabled";
++
++ dwc3 at 11000000 {
++ compatible = "snps,dwc3";
++ reg = <0x11000000 0xcd00>;
++ interrupts = <0 110 0x4>;
++ phys = <&hs_phy_0>, <&ss_phy_0>;
++ phy-names = "usb2-phy", "usb3-phy";
++ tx-fifo-resize;
++ dr_mode = "host";
++ };
++ };
++
++ usb3_1: usb30 at 1 {
++ compatible = "qcom,dwc3";
++ #address-cells = <1>;
++ #size-cells = <1>;
++ clocks = <&gcc USB30_1_MASTER_CLK>;
++ clock-names = "core";
++
++ ranges;
++
++ status = "disabled";
++
++ dwc3 at 10000000 {
++ compatible = "snps,dwc3";
++ reg = <0x10000000 0xcd00>;
++ interrupts = <0 205 0x4>;
++ phys = <&hs_phy_1>, <&ss_phy_1>;
++ phy-names = "usb2-phy", "usb3-phy";
++ tx-fifo-resize;
++ dr_mode = "host";
++ };
++ };
++
+ };
+ };
diff --git a/target/linux/ipq806x/patches-3.18/102-soc-qcom-gsbi-Add-support-for-ADM-CRCI-muxing.patch b/target/linux/ipq806x/patches-3.18/102-soc-qcom-gsbi-Add-support-for-ADM-CRCI-muxing.patch
new file mode 100644
index 0000000..f37ebeb
--- /dev/null
+++ b/target/linux/ipq806x/patches-3.18/102-soc-qcom-gsbi-Add-support-for-ADM-CRCI-muxing.patch
@@ -0,0 +1,258 @@
+diff --git a/Documentation/devicetree/bindings/soc/qcom/qcom,gsbi.txt b/Documentation/devicetree/bindings/soc/qcom/qcom,gsbi.txt
+index 4ce24d4..186e5f4 100644
+--- a/Documentation/devicetree/bindings/soc/qcom/qcom,gsbi.txt
++++ b/Documentation/devicetree/bindings/soc/qcom/qcom,gsbi.txt
+@@ -6,7 +6,8 @@ configuration settings. The mode setting will govern the input/output mode of
+ the 4 GSBI IOs.
+
+ Required properties:
+-- compatible: must contain "qcom,gsbi-v1.0.0" for APQ8064/IPQ8064
++- compatible: Should contain "qcom,gsbi-v1.0.0"
++- cell-index: Should contain the GSBI index
+ - reg: Address range for GSBI registers
+ - clocks: required clock
+ - clock-names: must contain "iface" entry
+@@ -16,6 +17,8 @@ Required properties:
+ Optional properties:
+ - qcom,crci : indicates CRCI MUX value for QUP CRCI ports. Please reference
+ dt-bindings/soc/qcom,gsbi.h for valid CRCI mux values.
++- syscon-tcsr: indicates phandle of TCSR syscon node. Required if child uses
++ dma.
+
+ Required properties if child node exists:
+ - #address-cells: Must be 1
+@@ -39,6 +42,7 @@ Example for APQ8064:
+
+ gsbi4 at 16300000 {
+ compatible = "qcom,gsbi-v1.0.0";
++ cell-index = <4>;
+ reg = <0x16300000 0x100>;
+ clocks = <&gcc GSBI4_H_CLK>;
+ clock-names = "iface";
+@@ -48,6 +52,8 @@ Example for APQ8064:
+ qcom,mode = <GSBI_PROT_I2C_UART>;
+ qcom,crci = <GSBI_CRCI_QUP>;
+
++ syscon-tcsr = <&tcsr>;
++
+ /* child nodes go under here */
+
+ i2c_qup4: i2c at 16380000 {
+@@ -76,3 +82,9 @@ Example for APQ8064:
+ };
+ };
+
++ tcsr: syscon at 1a400000 {
++ compatible = "qcom,apq8064-tcsr", "syscon";
++ reg = <0x1a400000 0x100>;
++ };
++
++
+diff --git a/drivers/soc/qcom/Kconfig b/drivers/soc/qcom/Kconfig
+index 7bd2c94..460b2db 100644
+--- a/drivers/soc/qcom/Kconfig
++++ b/drivers/soc/qcom/Kconfig
+@@ -4,6 +4,7 @@
+ config QCOM_GSBI
+ tristate "QCOM General Serial Bus Interface"
+ depends on ARCH_QCOM
++ select MFD_SYSCON
+ help
+ Say y here to enable GSBI support. The GSBI provides control
+ functions for connecting the underlying serial UART, SPI, and I2C
+diff --git a/drivers/soc/qcom/qcom_gsbi.c b/drivers/soc/qcom/qcom_gsbi.c
+index 729425d..09c669e 100644
+--- a/drivers/soc/qcom/qcom_gsbi.c
++++ b/drivers/soc/qcom/qcom_gsbi.c
+@@ -18,22 +18,129 @@
+ #include <linux/of.h>
+ #include <linux/of_platform.h>
+ #include <linux/platform_device.h>
++#include <linux/regmap.h>
++#include <linux/mfd/syscon.h>
++#include <dt-bindings/soc/qcom,gsbi.h>
+
+ #define GSBI_CTRL_REG 0x0000
+ #define GSBI_PROTOCOL_SHIFT 4
++#define MAX_GSBI 12
++
++#define TCSR_ADM_CRCI_BASE 0x70
++
++struct crci_config {
++ u32 num_rows;
++ const u32 (*array)[MAX_GSBI];
++};
++
++static const u32 crci_ipq8064[][MAX_GSBI] = {
++ {
++ 0x000003, 0x00000c, 0x000030, 0x0000c0,
++ 0x000300, 0x000c00, 0x003000, 0x00c000,
++ 0x030000, 0x0c0000, 0x300000, 0xc00000
++ },
++ {
++ 0x000003, 0x00000c, 0x000030, 0x0000c0,
++ 0x000300, 0x000c00, 0x003000, 0x00c000,
++ 0x030000, 0x0c0000, 0x300000, 0xc00000
++ },
++};
++
++static const struct crci_config config_ipq8064 = {
++ .num_rows = ARRAY_SIZE(crci_ipq8064),
++ .array = crci_ipq8064,
++};
++
++static const unsigned int crci_apq8064[][MAX_GSBI] = {
++ {
++ 0x001800, 0x006000, 0x000030, 0x0000c0,
++ 0x000300, 0x000400, 0x000000, 0x000000,
++ 0x000000, 0x000000, 0x000000, 0x000000
++ },
++ {
++ 0x000000, 0x000000, 0x000000, 0x000000,
++ 0x000000, 0x000020, 0x0000c0, 0x000000,
++ 0x000000, 0x000000, 0x000000, 0x000000
++ },
++};
++
++static const struct crci_config config_apq8064 = {
++ .num_rows = ARRAY_SIZE(crci_apq8064),
++ .array = crci_apq8064,
++};
++
++static const unsigned int crci_msm8960[][MAX_GSBI] = {
++ {
++ 0x000003, 0x00000c, 0x000030, 0x0000c0,
++ 0x000300, 0x000400, 0x000000, 0x000000,
++ 0x000000, 0x000000, 0x000000, 0x000000
++ },
++ {
++ 0x000000, 0x000000, 0x000000, 0x000000,
++ 0x000000, 0x000020, 0x0000c0, 0x000300,
++ 0x001800, 0x006000, 0x000000, 0x000000
++ },
++};
++
++static const struct crci_config config_msm8960 = {
++ .num_rows = ARRAY_SIZE(crci_msm8960),
++ .array = crci_msm8960,
++};
++
++static const unsigned int crci_msm8660[][MAX_GSBI] = {
++ { /* ADM 0 - B */
++ 0x000003, 0x00000c, 0x000030, 0x0000c0,
++ 0x000300, 0x000c00, 0x003000, 0x00c000,
++ 0x030000, 0x0c0000, 0x300000, 0xc00000
++ },
++ { /* ADM 0 - B */
++ 0x000003, 0x00000c, 0x000030, 0x0000c0,
++ 0x000300, 0x000c00, 0x003000, 0x00c000,
++ 0x030000, 0x0c0000, 0x300000, 0xc00000
++ },
++ { /* ADM 1 - A */
++ 0x000003, 0x00000c, 0x000030, 0x0000c0,
++ 0x000300, 0x000c00, 0x003000, 0x00c000,
++ 0x030000, 0x0c0000, 0x300000, 0xc00000
++ },
++ { /* ADM 1 - B */
++ 0x000003, 0x00000c, 0x000030, 0x0000c0,
++ 0x000300, 0x000c00, 0x003000, 0x00c000,
++ 0x030000, 0x0c0000, 0x300000, 0xc00000
++ },
++};
++
++static const struct crci_config config_msm8660 = {
++ .num_rows = ARRAY_SIZE(crci_msm8660),
++ .array = crci_msm8660,
++};
+
+ struct gsbi_info {
+ struct clk *hclk;
+ u32 mode;
+ u32 crci;
++ struct regmap *tcsr;
++};
++
++static const struct of_device_id tcsr_dt_match[] = {
++ { .compatible = "qcom,tcsr-ipq8064", .data = &config_ipq8064},
++ { .compatible = "qcom,tcsr-apq8064", .data = &config_apq8064},
++ { .compatible = "qcom,tcsr-msm8960", .data = &config_msm8960},
++ { .compatible = "qcom,tcsr-msm8660", .data = &config_msm8660},
++ { },
+ };
+
+ static int gsbi_probe(struct platform_device *pdev)
+ {
+ struct device_node *node = pdev->dev.of_node;
++ struct device_node *tcsr_node;
++ const struct of_device_id *match;
+ struct resource *res;
+ void __iomem *base;
+ struct gsbi_info *gsbi;
++ int i;
++ u32 mask, gsbi_num;
++ const struct crci_config *config = NULL;
+
+ gsbi = devm_kzalloc(&pdev->dev, sizeof(*gsbi), GFP_KERNEL);
+
+@@ -45,6 +152,32 @@ static int gsbi_probe(struct platform_device *pdev)
+ if (IS_ERR(base))
+ return PTR_ERR(base);
+
++ /* get the tcsr node and setup the config and regmap */
++ gsbi->tcsr = syscon_regmap_lookup_by_phandle(node, "syscon-tcsr");
++
++ if (!IS_ERR(gsbi->tcsr)) {
++ tcsr_node = of_parse_phandle(node, "syscon-tcsr", 0);
++ if (tcsr_node) {
++ match = of_match_node(tcsr_dt_match, tcsr_node);
++ if (match)
++ config = match->data;
++ else
++ dev_warn(&pdev->dev, "no matching TCSR\n");
++
++ of_node_put(tcsr_node);
++ }
++ }
++
++ if (of_property_read_u32(node, "cell-index", &gsbi_num)) {
++ dev_err(&pdev->dev, "missing cell-index\n");
++ return -EINVAL;
++ }
++
++ if (gsbi_num < 1 || gsbi_num > MAX_GSBI) {
++ dev_err(&pdev->dev, "invalid cell-index\n");
++ return -EINVAL;
++ }
++
+ if (of_property_read_u32(node, "qcom,mode", &gsbi->mode)) {
+ dev_err(&pdev->dev, "missing mode configuration\n");
+ return -EINVAL;
+@@ -64,6 +197,25 @@ static int gsbi_probe(struct platform_device *pdev)
+ writel_relaxed((gsbi->mode << GSBI_PROTOCOL_SHIFT) | gsbi->crci,
+ base + GSBI_CTRL_REG);
+
++ /*
++ * modify tcsr to reflect mode and ADM CRCI mux
++ * Each gsbi contains a pair of bits, one for RX and one for TX
++ * SPI mode requires both bits cleared, otherwise they are set
++ */
++ if (config) {
++ for (i = 0; i < config->num_rows; i++) {
++ mask = config->array[i][gsbi_num - 1];
++
++ if (gsbi->mode == GSBI_PROT_SPI)
++ regmap_update_bits(gsbi->tcsr,
++ TCSR_ADM_CRCI_BASE + 4 * i, mask, 0);
++ else
++ regmap_update_bits(gsbi->tcsr,
++ TCSR_ADM_CRCI_BASE + 4 * i, mask, mask);
++
++ }
++ }
++
+ /* make sure the gsbi control write is not reordered */
+ wmb();
+
+--
+1.9.1
+
diff --git a/target/linux/ipq806x/patches-3.18/103-ARM-DT-ipq8064-Add-TCSR-support.patch b/target/linux/ipq806x/patches-3.18/103-ARM-DT-ipq8064-Add-TCSR-support.patch
new file mode 100644
index 0000000..322e1d9
--- /dev/null
+++ b/target/linux/ipq806x/patches-3.18/103-ARM-DT-ipq8064-Add-TCSR-support.patch
@@ -0,0 +1,65 @@
+--- a/arch/arm/boot/dts/qcom-ipq8064.dtsi
++++ b/arch/arm/boot/dts/qcom-ipq8064.dtsi
+@@ -132,6 +132,7 @@
+
+ gsbi2: gsbi at 12480000 {
+ compatible = "qcom,gsbi-v1.0.0";
++ cell-index = <2>;
+ reg = <0x12480000 0x100>;
+ clocks = <&gcc GSBI2_H_CLK>;
+ clock-names = "iface";
+@@ -140,6 +141,8 @@
+ ranges;
+ status = "disabled";
+
++ syscon-tcsr = <&tcsr>;
++
+ uart2: serial at 12490000 {
+ compatible = "qcom,msm-uartdm-v1.3", "qcom,msm-uartdm";
+ reg = <0x12490000 0x1000>,
+@@ -167,6 +170,7 @@
+
+ gsbi4: gsbi at 16300000 {
+ compatible = "qcom,gsbi-v1.0.0";
++ cell-index = <4>;
+ reg = <0x16300000 0x100>;
+ clocks = <&gcc GSBI4_H_CLK>;
+ clock-names = "iface";
+@@ -175,6 +179,8 @@
+ ranges;
+ status = "disabled";
+
++ syscon-tcsr = <&tcsr>;
++
+ uart4: serial at 16340000 {
+ compatible = "qcom,msm-uartdm-v1.3", "qcom,msm-uartdm";
+ reg = <0x16340000 0x1000>,
+@@ -201,6 +207,7 @@
+
+ gsbi5: gsbi at 1a200000 {
+ compatible = "qcom,gsbi-v1.0.0";
++ cell-index = <5>;
+ reg = <0x1a200000 0x100>;
+ clocks = <&gcc GSBI5_H_CLK>;
+ clock-names = "iface";
+@@ -209,6 +216,8 @@
+ ranges;
+ status = "disabled";
+
++ syscon-tcsr = <&tcsr>;
++
+ uart5: serial at 1a240000 {
+ compatible = "qcom,msm-uartdm-v1.3", "qcom,msm-uartdm";
+ reg = <0x1a240000 0x1000>,
+@@ -279,6 +288,11 @@
+ status = "disabled";
+ };
+
++ tcsr: syscon at 1a400000 {
++ compatible = "qcom,tcsr-ipq8064", "syscon";
++ reg = <0x1a400000 0x100>;
++ };
++
+ qcom,ssbi at 500000 {
+ compatible = "qcom,ssbi";
+ reg = <0x00500000 0x1000>;
diff --git a/target/linux/ipq806x/patches-3.18/700-add-gmac-dts-suport.patch b/target/linux/ipq806x/patches-3.18/700-add-gmac-dts-suport.patch
index 89ebe66..348f24b 100644
--- a/target/linux/ipq806x/patches-3.18/700-add-gmac-dts-suport.patch
+++ b/target/linux/ipq806x/patches-3.18/700-add-gmac-dts-suport.patch
@@ -1,7 +1,7 @@
--- a/arch/arm/boot/dts/qcom-ipq8064-ap148.dts
+++ b/arch/arm/boot/dts/qcom-ipq8064-ap148.dts
-@@ -18,8 +18,15 @@
- bootargs = "console=ttyMSM0,115200 root=/dev/mtdblock12 rootfstype=squashfs,jffs2";
+@@ -22,8 +22,15 @@
+ linux,stdout-path = "serial0:115200n8";
};
+ aliases {
@@ -16,7 +16,7 @@
i2c4_pins: i2c4_pinmux {
pins = "gpio12", "gpio13";
function = "gsbi4";
-@@ -34,6 +41,25 @@
+@@ -38,6 +45,25 @@
bias-none;
};
};
@@ -42,16 +42,16 @@
};
gsbi at 16300000 {
-@@ -72,6 +98,7 @@
+@@ -76,6 +102,7 @@
#size-cells = <1>;
spi-max-frequency = <50000000>;
reg = <0>;
+ m25p,fast-read;
partition at 0 {
- label = "0:SBL1";
-@@ -148,5 +175,66 @@
- sata at 29000000 {
+ label = "lowlevel_init";
+@@ -136,5 +163,66 @@
+ usb30 at 1 {
status = "ok";
};
+
@@ -127,11 +127,10 @@
/ {
model = "Qualcomm IPQ8064";
-@@ -279,5 +280,42 @@
- #clock-cells = <1>;
- #reset-cells = <1>;
+@@ -390,5 +391,41 @@
+ };
};
-+
+
+ nss-gmac-common {
+ reg = <0x03000000 0x0000FFFF 0x1bb00000 0x0000FFFF 0x00900000 0x00004000>;
+ reg-names = "nss_reg_base" , "qsgmii_reg_base", "clk_ctl_base";
--
1.9.1
_______________________________________________
openwrt-devel mailing list
openwrt-devel at lists.openwrt.org
https://lists.openwrt.org/cgi-bin/mailman/listinfo/openwrt-devel
More information about the openwrt-devel
mailing list