[OpenWrt-Devel] [PATCH 30/32] atheros: convert AR5312 GPIO code to platform driver
Sergey Ryazanov
ryazanov.s.a at gmail.com
Thu Sep 11 22:00:47 EDT 2014
Signed-off-by: Sergey Ryazanov <ryazanov.s.a at gmail.com>
---
target/linux/atheros/config-3.14 | 1 +
target/linux/atheros/patches-3.14/100-board.patch | 76 +-------
.../atheros/patches-3.14/102-ar5312_gpio.patch | 194 +++++++++++++++++++++
.../atheros/patches-3.14/105-ar2315_pci.patch | 2 +-
4 files changed, 198 insertions(+), 75 deletions(-)
create mode 100644 target/linux/atheros/patches-3.14/102-ar5312_gpio.patch
diff --git a/target/linux/atheros/config-3.14 b/target/linux/atheros/config-3.14
index 3f7c76a..5d1041a 100644
--- a/target/linux/atheros/config-3.14
+++ b/target/linux/atheros/config-3.14
@@ -44,6 +44,7 @@ CONFIG_GENERIC_NET_UTILS=y
CONFIG_GENERIC_PCI_IOMAP=y
CONFIG_GENERIC_SMP_IDLE_THREAD=y
CONFIG_GPIOLIB=y
+CONFIG_GPIO_AR5312=y
CONFIG_GPIO_DEVRES=y
CONFIG_GPIO_SYSFS=y
# CONFIG_HAMRADIO is not set
diff --git a/target/linux/atheros/patches-3.14/100-board.patch b/target/linux/atheros/patches-3.14/100-board.patch
index 649ecf7..8ffa91c 100644
--- a/target/linux/atheros/patches-3.14/100-board.patch
+++ b/target/linux/atheros/patches-3.14/100-board.patch
@@ -1292,7 +1292,7 @@
+#endif /* __ASM_MACH_AR231X_AR2315_REGS_H */
--- /dev/null
+++ b/arch/mips/include/asm/mach-ar231x/ar5312_regs.h
-@@ -0,0 +1,247 @@
+@@ -0,0 +1,235 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License. See the file "COPYING" in the main directory of this archive
@@ -1525,24 +1525,12 @@
+#define MEM_CFG1_AC1 0x00007000 /* bank 1: SDRAM addr check (added) */
+#define MEM_CFG1_AC1_S 12
+
-+/* GPIO Address Map */
+#define AR5312_GPIO (AR5312_APBBASE + 0x2000)
-+#define AR5312_GPIO_DO (AR5312_GPIO + 0x00) /* output register */
-+#define AR5312_GPIO_DI (AR5312_GPIO + 0x04) /* intput register */
-+#define AR5312_GPIO_CR (AR5312_GPIO + 0x08) /* control register */
-+
-+/* GPIO Control Register bit field definitions */
-+#define AR5312_GPIO_CR_M(x) (1 << (x)) /* mask for i/o */
-+#define AR5312_GPIO_CR_O(x) (0 << (x)) /* mask for output */
-+#define AR5312_GPIO_CR_I(x) (1 << (x)) /* mask for input */
-+#define AR5312_GPIO_CR_INT(x) (1 << ((x)+8)) /* mask for interrupt*/
-+#define AR5312_GPIO_CR_UART(x) (1 << ((x)+16)) /* uart multiplex */
-+#define AR5312_NUM_GPIO 8
+
+#endif /* __ASM_MACH_AR231X_AR5312_REGS_H */
--- /dev/null
+++ b/arch/mips/ar231x/ar5312.c
-@@ -0,0 +1,536 @@
+@@ -0,0 +1,476 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License. See the file "COPYING" in the main directory of this archive
@@ -1687,51 +1675,6 @@
+ irq_set_chained_handler(AR5312_IRQ_MISC_INTRS, ar5312_misc_irq_handler);
+}
+
-+/*
-+ * gpiolib implementations
-+ */
-+static int
-+ar5312_gpio_get_value(struct gpio_chip *chip, unsigned gpio)
-+{
-+ return (ar231x_read_reg(AR5312_GPIO_DI) >> gpio) & 1;
-+}
-+
-+static void
-+ar5312_gpio_set_value(struct gpio_chip *chip, unsigned gpio, int value)
-+{
-+ u32 reg = ar231x_read_reg(AR5312_GPIO_DO);
-+
-+ reg = value ? reg | (1 << gpio) : reg & ~(1 << gpio);
-+ ar231x_write_reg(AR5312_GPIO_DO, reg);
-+}
-+
-+static int
-+ar5312_gpio_direction_input(struct gpio_chip *chip, unsigned gpio)
-+{
-+ ar231x_mask_reg(AR5312_GPIO_CR, 0, 1 << gpio);
-+ return 0;
-+}
-+
-+static int
-+ar5312_gpio_direction_output(struct gpio_chip *chip, unsigned gpio, int value)
-+{
-+ ar231x_mask_reg(AR5312_GPIO_CR, 1 << gpio, 0);
-+ ar5312_gpio_set_value(chip, gpio, value);
-+ return 0;
-+}
-+
-+static struct gpio_chip ar5312_gpio_chip = {
-+ .label = "ar5312-gpio",
-+ .direction_input = ar5312_gpio_direction_input,
-+ .direction_output = ar5312_gpio_direction_output,
-+ .set = ar5312_gpio_set_value,
-+ .get = ar5312_gpio_get_value,
-+ .base = 0,
-+ .ngpio = AR5312_NUM_GPIO, /* 8 */
-+};
-+
-+/* end of gpiolib */
-+
+static void ar5312_device_reset_set(u32 mask)
+{
+ u32 val;
@@ -2024,20 +1967,6 @@
+ mips_hpt_frequency = ar5312_cpu_frequency() / 2;
+}
+
-+static int __init
-+ar5312_gpio_init(void)
-+{
-+ int ret = gpiochip_add(&ar5312_gpio_chip);
-+
-+ if (ret) {
-+ pr_err("%s: failed to add gpiochip\n", ar5312_gpio_chip.label);
-+ return ret;
-+ }
-+ pr_info("%s: registered %d GPIOs\n", ar5312_gpio_chip.label,
-+ ar5312_gpio_chip.ngpio);
-+ return ret;
-+}
-+
+void __init
+ar5312_prom_init(void)
+{
@@ -2060,7 +1989,6 @@
+ devid >>= AR5312_REV_WMAC_MIN_S;
+ devid &= AR5312_REV_CHIP;
+ ar231x_board.devid = (u16)devid;
-+ ar5312_gpio_init();
+}
+
+void __init
diff --git a/target/linux/atheros/patches-3.14/102-ar5312_gpio.patch b/target/linux/atheros/patches-3.14/102-ar5312_gpio.patch
new file mode 100644
index 0000000..79fdfa1
--- /dev/null
+++ b/target/linux/atheros/patches-3.14/102-ar5312_gpio.patch
@@ -0,0 +1,194 @@
+--- a/arch/mips/ar231x/Kconfig
++++ b/arch/mips/ar231x/Kconfig
+@@ -1,6 +1,7 @@
+ config SOC_AR5312
+ bool "Atheros 5312/2312+ support"
+ depends on ATHEROS_AR231X
++ select GPIO_AR5312
+ default y
+
+ config SOC_AR2315
+--- a/arch/mips/ar231x/ar5312.c
++++ b/arch/mips/ar231x/ar5312.c
+@@ -192,6 +192,22 @@ static struct platform_device ar5312_phy
+ .num_resources = 1,
+ };
+
++static struct resource ar5312_gpio_res[] = {
++ {
++ .name = "ar5312-gpio",
++ .flags = IORESOURCE_MEM,
++ .start = AR5312_GPIO,
++ .end = AR5312_GPIO + 0x0c - 1,
++ },
++};
++
++static struct platform_device ar5312_gpio = {
++ .name = "ar5312-gpio",
++ .id = -1,
++ .resource = ar5312_gpio_res,
++ .num_resources = ARRAY_SIZE(ar5312_gpio_res),
++};
++
+ #ifdef CONFIG_LEDS_GPIO
+ static struct gpio_led ar5312_leds[] = {
+ { .name = "wlan", .gpio = 0, .active_low = 1, },
+@@ -282,6 +298,8 @@ int __init ar5312_init_devices(void)
+
+ platform_device_register(&ar5312_physmap_flash);
+
++ platform_device_register(&ar5312_gpio);
++
+ #ifdef CONFIG_LEDS_GPIO
+ ar5312_leds[0].gpio = config->sys_led_gpio;
+ platform_device_register(&ar5312_gpio_leds);
+--- a/drivers/gpio/Kconfig
++++ b/drivers/gpio/Kconfig
+@@ -108,6 +108,13 @@ config GPIO_MAX730X
+
+ comment "Memory mapped GPIO drivers:"
+
++config GPIO_AR5312
++ bool "AR5312 SoC GPIO support"
++ default y if SOC_AR5312
++ depends on SOC_AR5312
++ help
++ Say yes here to enable GPIO support for Atheros AR5312/AR2312+ SoCs.
++
+ config GPIO_CLPS711X
+ tristate "CLPS711X GPIO support"
+ depends on ARCH_CLPS711X || COMPILE_TEST
+--- a/drivers/gpio/Makefile
++++ b/drivers/gpio/Makefile
+@@ -15,6 +15,7 @@ obj-$(CONFIG_GPIO_ADNP) += gpio-adnp.o
+ obj-$(CONFIG_GPIO_ADP5520) += gpio-adp5520.o
+ obj-$(CONFIG_GPIO_ADP5588) += gpio-adp5588.o
+ obj-$(CONFIG_GPIO_AMD8111) += gpio-amd8111.o
++obj-$(CONFIG_GPIO_AR5312) += gpio-ar5312.o
+ obj-$(CONFIG_GPIO_ARIZONA) += gpio-arizona.o
+ obj-$(CONFIG_GPIO_BCM_KONA) += gpio-bcm-kona.o
+ obj-$(CONFIG_GPIO_BT8XX) += gpio-bt8xx.o
+--- /dev/null
++++ b/drivers/gpio/gpio-ar5312.c
+@@ -0,0 +1,121 @@
++/*
++ * This file is subject to the terms and conditions of the GNU General Public
++ * License. See the file "COPYING" in the main directory of this archive
++ * for more details.
++ *
++ * Copyright (C) 2003 Atheros Communications, Inc., All Rights Reserved.
++ * Copyright (C) 2006 FON Technology, SL.
++ * Copyright (C) 2006 Imre Kaloz <kaloz at openwrt.org>
++ * Copyright (C) 2006-2009 Felix Fietkau <nbd at openwrt.org>
++ * Copyright (C) 2012 Alexandros C. Couloumbis <alex at ozo.com>
++ */
++
++#include <linux/kernel.h>
++#include <linux/init.h>
++#include <linux/platform_device.h>
++#include <linux/gpio.h>
++
++#define DRIVER_NAME "ar5312-gpio"
++
++#define AR5312_GPIO_DO 0x00 /* output register */
++#define AR5312_GPIO_DI 0x04 /* intput register */
++#define AR5312_GPIO_CR 0x08 /* control register */
++
++#define AR5312_GPIO_CR_M(x) (1 << (x)) /* mask for i/o */
++#define AR5312_GPIO_CR_O(x) (0 << (x)) /* mask for output */
++#define AR5312_GPIO_CR_I(x) (1 << (x)) /* mask for input */
++#define AR5312_GPIO_CR_INT(x) (1 << ((x)+8)) /* mask for interrupt */
++#define AR5312_GPIO_CR_UART(x) (1 << ((x)+16)) /* uart multiplex */
++
++#define AR5312_GPIO_NUM 8
++
++static void __iomem *ar5312_mem;
++
++static inline u32 ar5312_gpio_reg_read(unsigned reg)
++{
++ return __raw_readl(ar5312_mem + reg);
++}
++
++static inline void ar5312_gpio_reg_write(unsigned reg, u32 val)
++{
++ __raw_writel(val, ar5312_mem + reg);
++}
++
++static inline void ar5312_gpio_reg_mask(unsigned reg, u32 mask, u32 val)
++{
++ ar5312_gpio_reg_write(reg, (ar5312_gpio_reg_read(reg) & ~mask) | val);
++}
++
++static int ar5312_gpio_get_val(struct gpio_chip *chip, unsigned gpio)
++{
++ return (ar5312_gpio_reg_read(AR5312_GPIO_DI) >> gpio) & 1;
++}
++
++static void ar5312_gpio_set_val(struct gpio_chip *chip, unsigned gpio, int val)
++{
++ u32 reg = ar5312_gpio_reg_read(AR5312_GPIO_DO);
++
++ reg = val ? reg | (1 << gpio) : reg & ~(1 << gpio);
++ ar5312_gpio_reg_write(AR5312_GPIO_DO, reg);
++}
++
++static int ar5312_gpio_dir_in(struct gpio_chip *chip, unsigned gpio)
++{
++ ar5312_gpio_reg_mask(AR5312_GPIO_CR, 0, 1 << gpio);
++ return 0;
++}
++
++static int ar5312_gpio_dir_out(struct gpio_chip *chip, unsigned gpio, int val)
++{
++ ar5312_gpio_reg_mask(AR5312_GPIO_CR, 1 << gpio, 0);
++ ar5312_gpio_set_val(chip, gpio, val);
++ return 0;
++}
++
++static struct gpio_chip ar5312_gpio_chip = {
++ .label = DRIVER_NAME,
++ .direction_input = ar5312_gpio_dir_in,
++ .direction_output = ar5312_gpio_dir_out,
++ .set = ar5312_gpio_set_val,
++ .get = ar5312_gpio_get_val,
++ .base = 0,
++ .ngpio = AR5312_GPIO_NUM,
++};
++
++static int ar5312_gpio_probe(struct platform_device *pdev)
++{
++ struct device *dev = &pdev->dev;
++ struct resource *res;
++ int ret;
++
++ if (ar5312_mem)
++ return -EBUSY;
++
++ res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
++ ar5312_mem = devm_ioremap_resource(dev, res);
++ if (IS_ERR(ar5312_mem))
++ return PTR_ERR(ar5312_mem);
++
++ ar5312_gpio_chip.dev = dev;
++ ret = gpiochip_add(&ar5312_gpio_chip);
++ if (ret) {
++ dev_err(dev, "failed to add gpiochip\n");
++ return ret;
++ }
++
++ return 0;
++}
++
++static struct platform_driver ar5312_gpio_driver = {
++ .probe = ar5312_gpio_probe,
++ .driver = {
++ .name = DRIVER_NAME,
++ .owner = THIS_MODULE,
++ }
++};
++
++static int __init ar5312_gpio_init(void)
++{
++ return platform_driver_register(&ar5312_gpio_driver);
++}
++subsys_initcall(ar5312_gpio_init);
diff --git a/target/linux/atheros/patches-3.14/105-ar2315_pci.patch b/target/linux/atheros/patches-3.14/105-ar2315_pci.patch
index 0f1c326..7630e94 100644
--- a/target/linux/atheros/patches-3.14/105-ar2315_pci.patch
+++ b/target/linux/atheros/patches-3.14/105-ar2315_pci.patch
@@ -358,7 +358,7 @@
+}
--- a/arch/mips/ar231x/Kconfig
+++ b/arch/mips/ar231x/Kconfig
-@@ -7,3 +7,10 @@ config SOC_AR2315
+@@ -8,3 +8,10 @@ config SOC_AR2315
bool "Atheros 2315+ support"
depends on ATHEROS_AR231X
default y
--
1.8.1.5
_______________________________________________
openwrt-devel mailing list
openwrt-devel at lists.openwrt.org
https://lists.openwrt.org/cgi-bin/mailman/listinfo/openwrt-devel
More information about the openwrt-devel
mailing list